HomeMy WebLinkAboutROOFING PERMIT INFORMATION SHEET t
L -
S�Tro LULL o P .. CAI ORKSooi_
ST LUCIE COUNTY ROOFING PERMIT INFORMATION SHEETP
Florida Building Code 7th Edition (2020)
Based on Section 1525.of the Florida Building Code-Building
INSTRUCTION PAGE
COMPLETE THE NECESSARY SECTIONS OF THE UNIFORM ROOFING SHEET.
APPLICATION FORM AND ATTACH THE REQUIRED.DOCUMENTS AS NOTED
BELOW;.,
Required Sections of Attachments.Require_d
Roof System the Permit Application See List Below
Form
Low Slope Application A,B,C ' -1,2,%4,5,6.7
Prescriptive BUR-RAS 150 A,B,C
Asphaltic Shingles A,B,`D' ..1,2,4,5,6,7
Concrete or Clay Tile A,B,"D,E
taI Roofs A,B..D 5,�,T
Wood Shingles and A,B,D . 1,2,4,5,6.7
Shakes _
Other As Applicable 1.2,3,4,5,6.7
ATTACHMENTS REQUIRED As Applicable):
1. Fire Directory Listing Page
2. From Product Approval:
Front Page
Specific System.Description
Specific System Limitations
r General Limitations
Applicable Detail Drawings
3.. .Design Calculations per Chapter 16,.or if applicable,RAS 127 or RA5128
4. Other Component of Product Approval
5. Municipal Permit Application
6. Owners Notification for Roofing Considerations(Reroofing Only)
7. .Any Required Roof Testing/Calculation Documentation
Form RooflnfoFeb21 Rev Feb 18,2021
Sim LUCIE WORKS
Section A(General Information).
Master Permit No. Process No.
Contractors-Name�o b� ��y�V��� —License-#—���/"Y—
Job Addrese (G" ?-A yt 'l %\N- 2rc-0— , 3'� q,�%
ROOF CATEGORY
0 Low Slope 0 Me anicallyFastened Tile . 13 Mortar/Adhesive Set Tiles
13Asphaltic Shingles etal Panel/Shingles Mood Shingles/Shakes
0 Prescriptive BUR-RAS 150
ROOF ROOF TYPE
0 New roof 0 Repair 0 Maintenance.. Reroofing 0 Recovering
ROOF SYSTEM INFORMATION
Low Slope Roof Area(SF) Steep Sloped Roof Area(SF Total(SF)72�c?L7
Section B(Roof Plan)
Sketch. Roof Plan: Illustrate all levels and sections, roof.drains,,scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and.levels,clearly identify dimensions of elevated pressure zones and location of parapets.
S-ed[on-D-jfteep_Slop�/R�Qo �Xsterror)
Roof System Manufacturer:
Notice of Acceptance Number:
Minimum Design Wind Pres's!�res,if Applicable(From RAS 127 or Calculations):
none r.a— Zone 2e:117=Zoni2nll.�one 2r:l�one 3e: one 3e:
Deck Type:
J.
Type;UnderisiymenC 0
ttlsulation
Vla .fk
Fire'i3amer:
RidgeVgrrtiJ� on? Fastener Type&_Spacing , �2
off'z A
. 77
Adhesive Type: ... `
Type Cap Sheet T et v� ►u.w�S Vl
Mean Roof Height: RmfCovering
S✓ ca.
Type&Sae Drip
Edge:
WORKS
Section C(Low Slope Roof) Surfacing:
Fill in specific roof assembly components and identify Fastener Spacing for Anchor/Base Sheet Attachment:
manufacturer Zone 1'—. ."oc @ Lap,#Rows_®=00
(If a component is not used,identify as"NA") Zone 1:_.._."oc 0-Lap,#Rows ® "00
System Manufacturer. Zone 2_"oc @ Lap,#Rows_®—"do '
Zone 3-_ .oc @ Lap,#Rows oc "
Product Approval No.:
Number of Fasteners-Per Insulation Board:
Design Wind Pressures,From RAS 128 Or Calculations: Zone 1'• Zone 1 Zone 2 Zone 3
Zone 1':_Zone 1: Zone 2:_Zone 3: Illustrate Components Noted and.Details as Applicable:
Max.Design Pressure,from the specific product approval Woodblocking, Gutter, Edge Termination, Stripping,
system:
--------------------__._- _______-_____- _____:__ _ .- ___:. -Flashing,-.-Continuous Cleat,-:Cant Strip, Base Flashing,
Counterflashing,Coping,Etc..
Deck: - Indicate: Mean Roof Height, Parapet Height, Height of Base
Type: Flashing,Component Material,Material'Thickness;Fastener
Type,Fastener Spacing orSubmit Manufacturers Details that
Gauge Thickness: Comply with RAS 111 and Chapter 16..
Slope:
Anchor/Base Sheet&No.df.Ply(s):
Anchor/Base Sheet Fastener/Bonding Material: FT'
Insulation Base Layer:-
Base Insultation Size and Thickness: Parapet
Base Insulation Fastener/Bonding Material:., Height
Top Insulation Layer:
Top Insulation Size and Thickness: FT.
Top Insulation Fastener/Bonding Material:
Mean
Base Sheet(s),&'No.of Ply(s): Roof
Base Sheet Fastener/Bonding Material: Height
Ply Sheet(s)'&No.of Ply(s):
Ply Sheet Fastener/Bonding Material:
Top Ply:
Top Ply Fastener/Bonding Material: