HomeMy WebLinkAboutNOA - PLANTATION ROOF TILEM1AMl- E
MIAM-DADS COUNTY
PRODUCT CONTROL SECTION
I F-PARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION
Miami, Florida 33175-2474
NOTICE OF ACCEPTANCE OA
T (786) 315-2590 F (786) 315-2599
www.miamidade.r_ov/economy
Soral Roofing, LLC
7575 Irvine Center Drive, Suite 100
Irvine, CA 92618
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AH4
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHd (in areas other than Miami -Dade County) reserve the right to have this product
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the
manufacturer will incur the expense of such testing and the AH7 may immediately revoke, modify, or suspend the use
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements
of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Plantation Roof Tile
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
in its entirety.
expiration date may be displayed in advertising literature. If any portion i the NOA is displayed, then it shall be done
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA #19-1021.02 and consists of pages 1 through 7.
The submitted documentation was reviewed by Freddy Semino
MIAMMADE CoUN NOA No., 20-1019.02
t Expiration Bate: 12/08/25
Approval Date: 11/19/20
Page 1 of 7
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub -Category: Roofing Tiles
Material: Concrete
L SCOPE
This approves a roofing system using Boral Plantation Concrete Roof Tile, as manufactured by Bond Roofing, LLC
in Okeechobee, FL as described in Section 2 of this Notice of Acceptance, designed to comply with the Florida
Building Code for High Velocity Hurricane Zone. For use in locations where the pressure requirements, as determined
by applicable Building Code, do not exceed the design pressure values obtain by calculations in compliance with RAS
127 using the values listed in section 4 herein. The attachment calculations shall be prepared m a moment based
system.
2. PRODUCT DESCRIPTION
Manufactured by Dimensions
Applicant
Plantation Tile Length: 16W'
Width: 13"
Test Product
Specifications Description
TAS 112 Flat profile concrete roof tile,
Type 3a Interlocking, Class III;
for direct deck or battened nail -on,
mortar or adhesive set applications.
Trim Pieces L = varies TAS 112 Accessory trim, concrete roof pieces for
W = varies use at hips, rakes, ridges and valley
Varying thickness terminations. Manufactured for each tile
profile.
2.1. MANUFACTURING LOCATION
1. Okeechobee, FL
2.2 PRODUCTS MANUFACTURED BY OTHERS
Product Name Product Description
ICP Adhesives Polyset®AH-160 Two component polymethane
foam adhesive.
TILE BONDr Roof Tile Adhesive Single component polyurethane
foam roof file adhesive.
DAP Foam Touch N Seal
StormBond® 2 Roof Tile Adhesive
Qailnete" Roof Tile Mortar, FL-15
Two component polyurethane
foam adhesive.
Premised, pre -bagged gray roof tile
mortar.
Manufacturer
(With Current NOS)
ICP Adhesives and Sealants, Inc.
The Dow Chemical Company
Dap Foam, Inc.
The Quikrete Companies, Inc.
MI MI MOO Coutrry NOA No.: 20-1019.02
r r Expiration Date: 12/08/25
Approval Date: 11/19/20
Page 2 of 7
2.3 SUBMITTED EVIDENCE:
Test Anencv Teat Identifier
American Test Lab of South RT0624.05-14
Florida RT0817.07-20
Redland Technologies
The Center for Applied
Engineering, Inc.
Redland Technologies
Redland Technologies
Redland Technologies
Redland Technologies
The Center for Applied
Engineering, Inc.
Walker Engineering, Inc.
Walker Engineering, Inc.
Walker Engineering, Inc.
Walker Engineering, Inc.
Farabaugh Engineering and
Testing Inc.
Fambaugb Engineering and
Testing Inc.
Farabaugh Engineering and
Testing Inc.
PRI Construction Material
Technologies
7161-03
Appendix RI
94-060B
94-084
7161-03
Appendix II
Letter Dated Aug. 1, 1994
P0631-01
P0402
Project No. 307025
Test #MDC-76
Calculations
Calculations
Calculations
Calculations
T295-11
T306-11
T279-11
DAPF-004-02-08
DAPF-004-02-09
DAPF-004-02-10
Test Name/Report
TAS 112
TAS 112
Static Uplift Testing
PA 102 & PA 102(A)
Static Uplift Testing
PA 101 (Adhesive Set)
(Mortar Set)
Wind Tunnel Testing
PA 109 (Nail -On)
Wind Tunnel Testing
PA 108 (Nail -On)
Wind Tunnel Testing
PA 108 (Mortar Set)
Withdrawal Resistance Testing of
screw vs. smooth shank nails
Wind Driven Rain
PA 100
Aerodynamic Multiplier
25-7183
25-7094
25-7496
25-7584
25-7804b-8
25-7804-4 & 5
25-7848-6
Two Patty Adhesive Set System
TAS-108
TAS-108
TAS-108
TAS 101
Static Uplift Resistance
Adhesive Set
Date
07/03/14
08/14/20
Dec. 1991
Much 1994
May 1994
Dec. 1991
Aug. 1994
July 1994
Sept. 1993
Oct. 1994
March 1999
April 1999
March 1995
February 1996
April 1996
December 1996
April 1999
10/05/11
10/04/11
09/23/11
07/26/18
07/26/18
07/26/18
mvu*M cxxjNf1• NOA No.: 20-1019.02
"• r Expiration Date: 12/08/25
Approval Date: 11/19/20
Page 3 of 7
3. LIMITATIONS
3.1 Fire classification is not part of this acceptance.
3.2 For mortar or adhesive set tile applications, a static field uplift test shall be performed in accordance with
TAS 106.
3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test
in accordance with TAS 112, appendix 'A'. Such testing shall be submitted to the Miami -Dade Product
Control office for review.
3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed
section 4.1 herein.
3.5 Minimum 4/12 slope requirement for mechanically attached tiles.
3.6 30/90 hot mopped underlaymem applications may be installed perpendicular to the roof slope unless stated
otherwise by the underlayment material manufacturers published literature.
3.7 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with
applicable building code.
3.8 All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code
and Rule 61G20-3 of the Florida Administrative Code.
4. INSTALLATION
4.1 Plantation Roof Tile and its components shall be installed in strict compliance with Roofing Application
Standard RAS 118, RAS 119 and RAS 120.
4.2 Data For Attachment Calculations
Table 1: Average Weight (W) and Dimensions (I x w )
Tile Profile
Weight-W (lbf)
Length -I (ft)
Width-w (ft)
Plantation Tile
11.6
1.375
1 1.08
Table 2: Aerodynamic Multipliers - X (ft3)
Tile
X (f3)
( )
Profile
Batten Application
Direct Deck Application
Plantation Tile
0.267
1 0 269
Table 3: Restoring Moments due to Gravity - M (ft: Ibf)
Tile
Greater than
Profile
2": 12"
3":12"
4": 12"
5": 12"
6": 12"
7":12"
Battens
Direct
Battens
Direct
Battens
Direct
Battens Direct
Battens Direct
Battens Direct
Deck
Deck
Deck
Deck
Deck
Deck
Plantation
N/A
7.91
N/A
7.19
5.75
7.67
6.61 7.52
6.44 7.32
6.26 7.04
Tile
NOA No.: 20-1019.02
Expiration Date: 12/08/25
Approval Date: 11/19/20
Page 4 of 7
Table 4: Attachment Resistance Expressed as a Moment - Mr (ft-lbf)
For Nail -On Systems
Tile
Profile
Fastener Type
Direct Deck
(Min 15132"
Direct Deck
(Min. 19/32"
Battens
plywood)
plywood)
Plantation Tile
2-1 Od Ring Shank
Nails
30.9
38.1
17,2
1-10d Smooth or
Screw Shank Nail
7.3
9 8
4 9
2-10d Smooth or
Screw Shank Nails
14.0
18.8
7.4
1 #8 Screw
2 #8 Screw
1-10d Smooth or
Screw Shank Nail
30.8
51.7
24.3
30.8
51.7
24.3
18.2
24.4
24.2
Field Clip)
1-10d Smooth or
Screw Shank Nail
19.0
19.0
22 1
Eave Clip)
2-10d Smooth or
Screw Shank Nails
35.5
35.5
3q,8
Field Clip)
2-10d Smooth or
Screw Shank Nails
31.9
31.9
32.2
Eave Clip)
2-10c Ring Shank
Nails'
50.3
65.5
48.3
I Installation with a 4" 81e headle and fastenera are located a minimum of 2'F."from the head of tile.
Table 5: Attachment Resistance Expressed as a Moment Mf (ft-lbf)
For Two Patty Adhesive Set Systems
Tile Profile
Tile Application
Minimum Attachment
Plantation Tile
Adhesive x
Resistance
2 So..
ee manufactures wm nent a royal for Installation re uirements.
3 The Dow Chemical Co. TILE BOND"" Roof Tile Adhesive wei ht per patty 13.9 grams. 31.3 ,
4 ICP Adhesive and Sealants, Inc. ICP Adhesve Polysel@ AH-160 Two -Cora onent Weight Der paq 8 grams. 31.3
5 DAP Foam Touch N Seal StonnBonde 2 Roof Tile Adhesive Weight per paddy 8 giams. 45
NIAMI-MDe ccuNW NOA No.: 20-1019.02
®' f Expiation Date: 12/08/25
Approval Date: 11/19/20
Page 5 of 7
able 6: Attachment RLI
ce Expressed as a Moment - Mr (ft-Ibf)
For Sin Adhesive Set S strofile
Thation
Tileesufactures
tFoam
con, orient a roval for instalirements.esive
and Sealants, Inc. ICP Adhesve PH-160 Two-Com onenl wei ht r 45 rams.
118.9
sive and Sealants, Inc. ICP Adhesve P-160 Two -Component wei ht er 24 rams
40.4
m Touch N Seal StormBondo 2 Roof Tie wei ht r Padd 45 rams.
73
m Touch N Seal Sto"Bonde 2 Roof Tile Adhesive weight per ad 24
rams
48
Table 7: Attachment Resistance Expressed as a Moment - Mf (ft-lbf)
for Mortar Set Systems
Tile Pfile Tile Application Attachment
Resistance
Plantarotion Tile Mortar Sets 39.0
See s ec�c mortar manufacturer's Notice of Acceptance.
5. LABELING
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo as seen below or following
statement: "Miami -Dade County Product Control Approved".
y]p
"��* E U V T E E R M V6ffi)
BORAL PLANTATION ROOF THE LABEL (LOCATED ON UNDERSIDE OF TILE)
6. BUILDING PERMIT REQUB2EMENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6.1.1 This Notice of Acceptance.
6.1.2 Any other documents required by Building Official or Applicable building code in order to properly
evaluate the installation of this system.
MIAMI DARE COUNTY NOA No.: 20-1019.02
i� Expiration Date: 12/08/25
Approval Date: 11/19/20
Page 6 of 7
PROFILE DRAWING
BORAL PLANTATION FLAT CONCRETE TILE
END OF THIS ACCEPTANCE
M"I- A ECOUNTY NOA No.: 20-1019.02
Expiration Date: 12/08/25
Approval Date: 11/19/20
Page 7 of 7