Loading...
HomeMy WebLinkAboutNOA - BUITIMENT ROOF SYSTEM OVER WOOD DECKMIAMi 021. MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) . www.miamidade.goy/economy Polyglass USA, Inc. 1111 W. Newport Center Drive Deerfield Beach, FL 33442 SCOPE:��9 This NOA is being issued under .the applicable rules and regulations governing the use of cons�i"oi�materials. The documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to, perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Polyglass Modified Bitumen Roof System Over Wood Decks LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA #17-0824.09 and consists of pages 1 through 65. The submitted documentation was reviewed by Alex Tigera. NOA No.: 17-0825.01 MIAMI•DAD, COUNTY Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 1 of 65 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub -Category: Modified Bitumen Materials SBS/APP Deck Type: Wood Maximum Design Pressure -120 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE I Product Polyglass G2 Base Polyflex SA Base Elastoshield HT XtraFlex SBS HT Base 650 Elastobase Elastoflex SA V Elastoflex SA V FR Elastoflex SA V PLUS Elastoflex SA V PLUS FR Elastoflex V Elastoflex V G Test Dimensions Specification 108' x 36" ASTM D 4601 Type II 66' 8" x 3' 3-3/8" ASTM D 4601 Type H 65' 8" x 3' 3-3/8" ASTM D 6162 65' 8" x 3' 3-3/8" ASTM D 6162 Product i Description Asphalt -coated fiberglass reinforced base sheet Self -adhered, fiberglass reinforced, APP modified bitumen base sheet. SBS modified asphalt coated fiberglass/polyester reinforced base sheet. SBS modified asphalt coated fiberglass/polyester reinforced base sheet. 65' 8" x 3' 3-3/8" ASTM D 6163 SBS modified asphalt coated fiberglass reinforced base sheet. 66' 8" x 3' 33/8" ASTM D 6163, Type I 66' 8" x 3' 3 3/s" ASTM D 6163 66' 8" x 3' 33/8" ASTM D 6163 66' 8" x 3' 3 3/8" ASTM D 6163 32' 10" x 3' 3-3/8" ASTM D 6163 32' 10" x 3' 3-3/8" ASTM D 6163 Self -adhered, fiberglass reinforced, SBS modified bitumen membrane with a self -adhering back face and a smooth top surface. Self -adhered, fire -rated, fiberglass reinforced, SBS modified bitumen membrane with a self -adhering back face and a smooth top surface. Self -adhered, fiberglass reinforced, SBS modified bitumen membrane with a self -adhering back face and a smooth top surface. Self -adhered, fiberglass reinforced, SBS modified bitumen membrane with a fire retardant additive, self - adhering back face and a smooth top surface. Torch, hot asphalt or cold adhesive applied, fiberglass reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a sanded top surface. Torch, hot asphalt or cold adhesive applied, fiberglass reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 2 of 65 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description Elastoflex V G FR 32' 10" x 3' 3-3/8" ASTM D 6163 Torch, hot asphalt or cold adhesive applied, fire -rated, fiberglass reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. XtraFlex SBS Base 66' 8" x 3' 3 3/8" ASTM D 6163 Self -adhered, fiberglass reinforced, SBS modified SA bitumen membrane with a self -adhering back face and a smooth top surface. XtraFlex SBS Glass 65' 8" x 3' 3-3/8" ASTM D 6163 SBS modified asphalt coated fiberglass reinforced base Base sheet. XtraFlex SBS Glass 32' 10" x 3' 3-3/8" ASTM D 6163 Torch, hot asphalt or cold adhesive applied, fiberglass Interply reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a sanded top surface. Elastobase P 65' 8" x 3' 3-3/8" ASTM D 6164 SBS modified asphalt coated polyester reinforced base sheet. Elastoflex S6 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a polyethylene or sanded top surface. Elastoflex S6 G 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. Elastoflex S6 G FR 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold ' adhesive applied, fire -rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. Elastoshield TS G 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold, adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. Elastoshield TS G FR 32' 10" x 3' 3-3/8" ASTM D 6164 Polyfresko G SBS 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold adhesive applied, fire -rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified' bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 3 of 65 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description Polyfresko G SBS FR 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold adhesive applied, fire -rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. XtraFlex SBS Poly 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester Base reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a polyethylene or sanded top surface. XtraFlex SBS Poly G 32' 10" x 3' 3-3/8" ASTM D 6164 Torch, hot asphalt or cold adhesive applied, fire -rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. Polybond 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Polybond G 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. Polyflex 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Polyflex G 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. Polyflex G FR 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, fire -rated, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface and fire retardant chemistry. Polyfresko G 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. Polyfresko G FR 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, fire -rated, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface and fire retardant chemistry. XtraFlex APP G 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, fire -rated, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface and fire retardant chemistry. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 4 of 65 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Test Product Product Dimensions Specification Description XtraFlex APP S 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with aiburn off polyethylene back face and a smooth or sanded top surface. XtraFlex Kool APP G 32' 10" x 3' 3-3/8" ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane.with auburn off polyethylene back . face and a granule top surface. Polyglass Base 65' 8" x 3' 33%8" ASTM D 6509 APP modified asphalt coated fiberglass reinforced base Type I sheet. i PG 100 1, 3, 5, 50, 55 gal, ASTM D41 A penetrating solution of solvent and a blend of tube or 17 oz. spray selected asphalts used to promote adhesion. can XtraFlex 10 1, 3, 5, 50, 55 gal, ASTM D41 A penetrating solution of solvent and a blend of tube or 17 oz. spray selected asphalts used to promote adhesion. can PG 350 1, 3, 5, 50, 55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with tube Type III modified bitumen membranes. POLYPLUS 35 1, 3, 5, 50, 55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with tube Type III modified bitumen membranes. XtraFlex 35 1, 3, 5, 50, 55 gal. or ASTM D3019 A fibered rubberized adhesive designed for use with tube Type III modified bitumen membranes. PG 450 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement. tube PG 500 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use tube with modified bitumen membranes. POLYPLUS 45 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement. tube POLYPLUS 50 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use tube with modified bitumen membranes. XtraFlex 50 Premium 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use Modified Wet/Dry tube with modified bitumen membranes. Cement PG 400 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use in tube ASTM D3409 dry or damp conditions. PG 425 1, 3, 5, 50, 55 gal. or ASTM D4586 A thick, fibered, rubberized flashing cement for use in tube ASTM D3409 dry or damp conditions. WB-3000 5 gallon pail Proprietary A low-VOC, water -based acrylic primer to enhance adhesion of self-adhered'membranes. i NOA No.: 17-0825.01 r IAMI-Dane COUNTY Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 5 of 65 APPROVED INSULATIONS: Product Name Polytherm Polytherm-H Polytherm G XtraFlex Polyiso XtraFlex Polyiso G ACFoam-1I ACFoam-III DensDeck DensDeck Prime FescoBoard H-Shield H-Shield-CG ENRGY 3 Multi -Max FA-3 SECUROCK Gypsum -Fiber Roof Board EnergyGuard Polyiso Insulation ISO 95+ GL TABLE 2 Product Description Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Gypsum insulation board Gypsum insulation board Rigid perlite roof insulation board. Polyisocyanurate foam insulation Polyisocyanurate/perlite composite insulation Polyisocyanurate foam insulation Polyisocyanurate foam insulation Fiber reinforced coverboard Polyisocyanurate foam insulation Polyisocyanurate foam insulation Structodek High Density Fiberboard Roof Wood fiber board Insulation Manufacturer (With Current NOA) Polyglass USA, Inc. Polyglass USA, Inc. Polyglass USA, Inc. Polyglass USA, Inc. Polyglass USA, Inc. Atlas Roofing Corporation Atlas Roofing Corporation Georgia Pacific Gypsum LLC Georgia Pacific Gypsum LLC Johns Manville Corp. Hunter Panels, LLC Hunter Panels, LLC Johns Manville Corp. Rmax Operating, LLC USG Corporation GAF Firestone Building Products Company, LLC Blue Ridge Fiberboard, Inc. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 6 of 65 APPROVED FASTENERWADHESIVES: TABLE 3 Fastener Product Product Manufacturer Number Name Description Dimensions (With Current NOA) 1. Polygrip Fastener #12 Insulation fastener for wood, steel Various Polyglass USA, Inc. and concrete decks 2. Polygrip Fastener #14 Insulation fastener for wood, steel Various Polyglass USA, Inc. and concrete decks 3. Polygrip Fastener #15 Insulation fastener for wood, steel Various Polyglass USA, Inc. and concrete decks 4. Polygrip Hex Plate Galvalume hex stress plate. 2 7/8" x Polyglass USA, Inc. 3 1/4" 5. Dekfast DF-#12-PH3 Insulation fastener for wood, steel Various SFS Group USA, Inc. and concrete decks 6. Dekfast DF-#14-PH3 Insulation fastener for wood, steel Various SFS Group USA, Inc. and concrete decks 7. Dekfast DF-#15-PH3 Insulation fastener for wood, steel Various SFS Group USA, Inc. and concrete decks 8. Dekfast PLT-H-2-7/8 Galvalume hex stress plate. 2'/8" x SFS Group USA, Inc. 3 '/4" 9. #12 Standard Roofgrip Insulation and membrane fastener Various OMG, Inc. 10. #14 Roofgrip Insulation and membrane fastener Various OMG, Inc. 11. Flat Bottom Metal Galvalume AZ50 stress plate 3" square OMG, Inc. Plate 12. Trufast #14 HD Insulation fastener for steel and wood Various Altenloh, Brinck & Co. Fastener decks U.S., Inc. 13. Trufast 3" Metal Galvalume steel plate 3" round Altenloh, Brinck & Co. Insulation Plate U.S., Inc. 14. 3 in. Round Metal Galvalume stress plate. 3" round OMG, Inc. Plate 15. OMG Heavy Duty Truss head, self -drilling, pinch point Various OMG, Inc. fastener 16. Trufast #12 DP Carbon steel screw with #3 phillips Various Altenloh, Brinck & Co. Fastener drive U.S., Inc. 17. OMG 3" Galvalume Galvalume coated steel plate 3" round OMG, Inc. Steel Plate 18. AccuTrac Flat Bottom Aluminized steel plate 3" square OMG, Inc. 19. Simplex MAXX Cap Polymer stress plate with two ring 3" round x 1" Simplex Nails. Inc. Fasteners shank nails long NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 7 of 65 APPROVED FASTENERS/ADHESIVES: TABLE 3 Fastener Product Product Manufacturer Number Name Description Dimensions (With Current NOA) 20. ICP Adhesives CR-20 A two component elastomeric ICP Adhesives and polyurethane foam adhesive Sealants, Inc. 21. Insta Stick Quik Set A single component urethane foam The Dow Chemical Co. Insulation Adhesive adhesive 22. Millennium One Step A two component, low rise, H.B. Fuller Company Foainable Insulation polyurethane foam adhesive Adhesive '23. Millennium One Step A two component, low rise, H.B. Fuller Company Green Foamable polyurethane foam adhesive Insulation Adhesive 24. Millennium PG-1 A two component, low rise,' H.B. Fuller Company Pump Grade Adhesive polyurethane foam adhesive 25. OlyBond 500 A two component polyurethane foam OMG, Inc. adhesive 26. OlyBond 500 Green A two component, low rise, OMG, Inc. polyurethane foam adhesive APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Number Product Product Application Specification Manufacturer Name Description Rate 1. Gravel To be installed in a flood coat 400 lbs/sq N/A Generic of approved asphalt at 60 Ibs/sq 2. Slag To be installed in a flood coat 300 lbs/sq N/A Generic of approved asphalt at 60 Ibs/sq 3. KM Acryl 15 A premium white or tinted 1-1'/2 gallsq ASTM D6083 Polyglass USA, elastomeric acrylic based roof Inc. coating (water -based). A polyester fabric may be used for reinforcement with this coating. 4. KM Acryl 15 QS A premium white or tinted 1-1 %z gallsq ASTM D6083 Polyglass USA, quick setting, elastomeric Inc. acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 8 of 65 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Number Product Product Application Specification Manufacturer Name Description Rate 5. KM Acryl 25 A premium white or tinted 1-1'h gaUsq ASTM D6083 Polyglass USA, elastomeric acrylic based roof Inc. coating (water -based). A polyester fabric may be used for reinforcement with this coating. 6. KM Acryl 25 QS A premium white or tinted 1-1 %Z gal/sq ASTM D6083 Polyglass USA, quick setting, elastomeric Inc. acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. 7. KM -PS #220 A single component, white or 1.25 gal/sq ASTM D6694 Polyglass USA, tinted, solvent, moisture cure Inc. silicone coating. 8. KM -PS #250 A premium grade high solids, 1.25 gal/sq ASTM D6694 Polyglass USA, white or tinted, single Inc. component, moisture cure, fluid applied silicone coating 9. PG 300 An asphalt cutback fibered roof 1'/2-2 gal/sq ASTM D4479 Polyglass USA, coating. May be applied by Inc. brush or spray equipment to rejuvenate aged BUR 10. PG 600 Non-fibered aluininuin roof %2-1 gaUsq ASTM D2824 Polyglass USA, coating. Type I Inc. 11. PG 650 Fibered aluminum roof coating. 1'/2-2 gaUsq 12. PG 700 A premium white or tinted elastomeric acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. 1-1'/z gal/sq ASTM D2824 Polyglass USA, Type III Inc. ASTM D6083 Polyglass USA, Inc. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 9 of 65 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Number Product Product Application Specification Manufacturer Name Description Rate 13. PG 700 QS A premium white or tinted 1-1'/2 gal/sq ASTM D6083 Polyglass USA, quick setting, elastomeric Inc. acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. 14. PG 800 An asphalt based, non-fibered 3 gal/sq in two ASTM D1227 Polyglass USA, clay emulsion coats Inc. 15. PolyBrite 70 A premium white or tinted 1-1'/z gaUsq ASTM D6083 Polyglass USA, elastomeric acrylic based roof Inc. coating (water -based). A polyester fabric may be used for reinforcement with this coating. 16. PolyBrite 70 QS A premium white or tinted 1-1'/2 gaUsq ASTM D6083 Polyglass USA, quick setting, elastomeric Inc. acrylic based roof coating (water -based). A polyester fabric may be used for reinforcement with this coating. 17. PolyBrite 90 A premium grade high solids, 1.25 gal/sq ASTM D6694 Polyglass USA, white or tinted, single Inc. component, moisture cure, fluid applied silicone coating 18. PolyBrite 95 A single component, white or 1.25 gal/sq ASTM D6694 Polyglass USA, tinted, solvent, moisture cure Inc. silicone coating. 19. POLYPLUS 60 Non-fibered aluminum roof ''/2-1 gal/sq ASTM D2824 Polyglass USA, coating. Type I Inc. 20. POLYPLUS 65 Fibered aluminum roof coating. 1'/2-2 gaUsq ASTM D2824 Polyglass USA, Type III Inc. 21. XtraFlex 60 Aluminum Non-fibered aluminum roof %2-1 gaUsq ASTM D2824 Polyglass USA, Roof Coating coating. Type I Inc. 22. XtraFlex 65 Aluminum Fibered aluminum roof coating. 1 %2-2 gaUsq ASTM D2824 Polyglass USA, Roof Coating Fibered Type III Inc. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 10 of 65 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer's application instructions. Number Product Product Application Specification Manufacturer Name Description Rate 23. XtraFlex 70 Premium A premium white or tinted 1-1'h gaUsq ASTM D6083 Polyglass USA, Acrylic FR Roof elastomeric acrylic based roof Inc. Coating coating (water -based). A polyester fabric may be used for reinforcement with this coating. 24. XtraFlex 80 Emulsion An asphalt based, non-fibered 3 gal/sq in two ASTM D1227 Polyglass USA, Roof Coating clay emulsion coats i Inc. 25. XtraFlex 30 An asphalt cutback fibered roof 1'/z-2 gaUsq ASTM D4479 Polyglass USA, Bituminous Roof coating. May be applied by Inc. Coating Fibered brush or spray equipment to 1 rejuvenate aged BUR 26. XtraFlex SRC 8000 A single component, white or 1.25 gal/sq ASTM D6694 Polyglass USA, tinted, solvent, moisture cure Inc. silicone coating. 27. XtraFlex SRC 9600 A premium grade high solids, 1.25 gal/sq ASTM D6694 Polyglass USA, single component, white or Inc. tinted, moisture cure, fluid applied silicone coating NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 11 of 65 EVIDENCE SUBMITTED: Test Agency Factory Mutual Research Corporation Underwriters Laboratory Trinity I ERD PRI Asphalt Technologies Test Name/Report 4470 Report No. Date 2W7A7.AM 08.04.94 4470 3000857 01.12.00 4470 3004091 01.12.00 4470 3001334 02.15.00 4470 3031350 09.27.07 4470 RR202591 10.22.15 TAS 114 OONK20869 06.08.00 UL 790 R14571 06.30.15 TAS 114 TAS 114 TAS 114 TAS 117(B)-ASTM D6862 ASTM D 6164 / D 6222 TAS 114 ASTM D6163 / ASTM D 4601 FM 4470 & TAS 114 TAS' 117 (B) & TAS 114 ASTM D6164 TAS 114 TAS 114 ASTM D6509 ASTM D6222 ASTM D6222 ASTM D6163 ASTM D6164 TAS 114 & FM 4474 ASTM D4601 / TAS 117 ASTM D4601 ASTM D6162 ASTM D6162 ASTM D6163 ASTM D6163 TAS 114 & FM 4474 TAS 114 & FM 4474 TAS 114 ASTM D6222 ASTM D6163 ASTM D6694 ASTM D6694 11751.05.03 11758.08.03 P 1738.02.07 C8500SC.11.07 P 10490.10.08-R1 P13760.09.09 P33960.03.11 P33970.03.11 P39680.03.13 P37590.03.13-3A 11757.12.00-1-R1 11757.04.01-1-R1 P37590.03.13-1-R1 P37590.07.13-2 P37590.03.13-5-R1 P37590.03.13-2-R1 P37590.07.13-1 P41630.08.13 P45940.09.13 P44370.10.13 SC5170.05.15 SC5170.12.15-1 PLYG-P45440SC.03.15-2-RI PLYG-P45440SC.03.15-1-R1 PLYG-SC8905.05.16-1 PLYG-SC8905.05.16-2 P 1734.07.06-R2 PUSA-062-02-01 PUSA-064-02-02 PUSA-134-02-01 PUSA-135-02-01 05.30.03 08.11.03 02.05.07 11.30.07 10.03.08 09.10.09 03.15.11 03.15.11 03.04.13 03.06.13 04.29.13 04.30.13 06.26.13 07.01.13 07.01.13 07.01.13 07.02.13 08.06.13 09.04.13 10/04/13 05.08.15 12/29/15 12.29.15 02.19.16 05.17.16 05.17.16 08.24.16 12.04.07 02.27.08 05.16.14 05.16.14 NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 12 of 65 APPROVED ASSEMBLIES Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type A(1): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Elastobase*, Elastoshield HT*, Polyglass G2 Base XtraFlex SBS Glass Base* or XtraFlex SBS HT Base 650* fastened to the deck as described below: *Only with OMG or Trufast fastening components. Fastening #1: Attach anchor sheet using 11 ga. annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet. Fastening #2: Attach anchor sheet using OMG Roofgrip Fasteners with Flat Bottom Metal Plates, Dekfast DF-#14-PH3 with Dekfast PLT-H-2-7/8, Polygrip Fasteners #14 with Polygrip Hex Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet. One or more layers of any of the following insulations: Base Insulation Laver (Optional) Insulation Fasteners Fastener Table 3 Density/ft' ENRGY 3, ISO 95+ GL, ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam- IH, H-Shield, Polytherm-H, Multi -Max FA-3 Minimum 1.5" thick - N/A N/A Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Top Insulation Layer Insulation Fasteners Fastener Table 3 Density/ftz FescoBoard Minimum'/" thick N/A N/A Structodek High Density Fiberboard Roof Insulation Minimum %Z" thick N/A N/A DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'/" thick N/A N/A NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 13 of 65 Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range and at a rate of 20-40 lbs/100 ft'. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base or one ply of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass, Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered to DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board.*Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 14 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated ; Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Elastobase*, Elastoshield HT*, Polyglass G2 Base, XtraFlex SBS Glass Base* or XtraFlex SBS HT Base 650* fastened to the deck as described below: *Only with OMG or Trufast fastening components. Fastening: Attach anchor sheet using Polygrip Fastener #14 with Polygrip Hex Plates or Dekfast DF-#14- PH3 with Dekfast PLT-H-2-7/8 or OMG Heavy -Duty with OMG 3 Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrae Flat Bottom Plates or Trufast #14 HD with Trufast 3" Metal Insulation Plate or Simplex MAXX Cap Fasteners spaced 10" o.c. in 4" lap -and 10" o.c. in three equally spaced staggered center rows. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener Table 3 ' Density/ft2 ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield, Polytherm-H, ENRGY 3, Multi -Max FA-3 Minimum 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener Table 3 ; Density/ft2 DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum V4" thick N/A N/A Note: All insulation shall be adhered in a full mopping of approved asphalt within the EVT range and at a rate of .20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 15 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT. Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 16 of 65 Membrane Type: SBS/APP Deck Type II: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type A(3): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Elastobase, Elastoshield HT, Polyglass G2 Base, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: Attach anchor sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates spaced 12" o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet. One or more layers of any of the following insulations: Base Insulation Laver (Optional) Insulation Fasteners Fastener Table 3 Density/ft2 ENRGY 3, ISO 95+ GL, ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield, Polytherm-H, Multi -Max FA-3 Minimum 1.511 thick N/A N/A Top Insulation Laver Insulation Fasteners Fastener Table 3 Density/ft' DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum 1/" thick N/A N/A FescoBoard Minimum'/" thick N/A N/A Structodek High Density Fiberboard Roof Insulation Minimum 1/2" thick N/A N/A Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 17 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base or one ply of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered to DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 18 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 11/32" plywood or wood plank attached to structural supports.at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type A(4): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Elastobase, Elastoshield HT, Polyglass G2 Base or XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below.. Fastening: Attach anchor sheet using 11 ga. annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet. One or more layers of any of the following insulations: Base Insulation Laver (Optional) Insulation Fasteners Fastener Table 3 Density/ft' ENRGY 3, ISO 95+ GL, ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield, Polytherm-H; Multi -Max FA-3 Minimum 1.5" thick N/A N/A Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 20-40 lbs/100 ft'. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Top Insulation Laver FescoBoard Minimum 1/4" thick Structodek High Density Fiberboard Roof Insulation Minimum %z" thick DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'/a" thick Insulation Fasteners Fastener Table 3 ; Density/ft2 N/A N/A N/A N/A N/A N/A Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 19 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base or one ply of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered to DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -60 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 20 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. "/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type A(5): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: Attach anchor sheet -using 12 ga. annular ring shank nails and 1-5/8" tin -caps attached 6" o.c. in 4" lap and 6" o.c. in four equally spaced staggered center rows. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Table 3 Fastener Density/fe ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield, Polytherm-H, H-Shield-CG, Multi -Max FA-3, ENRGY 3 Minimum 1" thick N/A N/A Note: All insulation shall be adhered to the anchor sheet with Millennium One -Step Foamable Adhesive, Millennium One Step Green Foamable Insulation Adhesive, Millennium PG-1 Pump Grade Adhesive, OlyBond 500; OlyBond 500 Green, Insta StikTM Quik Set Insulation Adhesive, WP Adhesives CR-20 applied in continuous rows 12" o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base or one ply of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 21 of 65 Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base or one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -60 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 22 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type A(6): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below: Fastening: Attach anchor sheet using 12 ga. annular ring shank nails and 1-5/8" tin -caps attached 8" o.c. in 4" lap and 8" o.c. in four equally spaced staggered center rows. One or more layers of any of the following insulations: Base Insulation Laver Insulation Fasteners Fastener Table 3 Density/ft2 ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield, Polytherm-H, ENRGY 3, Multi -Max FA-3 Minimum 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener Table 3 Density/ftz DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum I/a" thick N/A N/A Note: All insulation shall be adhered in a full mopping,of approved asphalt within the EVT range and at a rate of 20-40 Ibs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 23 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -67.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 24 of 65 Membrane Type:. SBS/APP Deck Type 1I: Wood, Insulated Deck Description: . Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #10 screws at 6" o.c. System Type A(7): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below: Fastening: Attach anchor sheet using Polygrip Fastener #14 with Polygrip Hex Plates or Dekfast DF-#14- PH3 with Dekfast PLT-H-2-7/8 or OMG Heavy -Duty with OMG 3", Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrac Flat Bottom Plates or Trufast #14 HD with Trufast 3" Metal Insulation Plates spaced 9" o:c. in 4" lap and 9" o.c. in four equally spaced staggered center rows. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener Table 3 � Density/ft' ACFoam-H, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, H-Shield, Polytherm-H, ENRGY 3, Multi -Max FA-3 Minimum 1.5" thick N/A N/A Top Insulation Laver Insulation Fasteners Fastener Table 3 Density/ft2 DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board Minimum 1/" thick N/A N/A Note: All insulation shall be adhered in a full mopping of approved asphalt within the EVT range and at a rate of 20-40 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second Payer of approved top layer insulation installed as the final membrane substrate. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 25 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*,Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in Rill mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -82.5 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 26 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. "/32" plywood or wood plank attached to structural supports at,a maximum of 24" o.c. with #10 screws at 6" o.c. System Type A(8): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below: Fastening: Attach anchor sheet using 12 ga. annular ring shank nails and 1-5/8" tin -caps attached 8" o.c. in 4" lap and 8" o.c. in four equally spaced staggered center rows. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener Table 3 Density/ft2 ACFoam-II, Polytherm, Polytherm G, XtraFlex Polyiso, XtraFlex Polyiso G, ACFoam-III, I -I -Shield, Polytherm-H, ENRGY 3, Multi -Max FA-3 Minimum 1.5" thick N/A N/A Top Insulation Layer Insulation Fasteners Fastener Table 3 � Density/ft2 SECUROCK Gypsum -Fiber Roof Board Minimum 114" thick ILUM N/A Note: All insulation shall be adhered in a full mopping of approved asphalt within the EVT range and at a rate of 20-40 lbs/100 fe. , Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer_of approved top layer insulation installed as the final membrane substrate. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 27 of, 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -90.0 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 28 of 65 Membrane Type: SBS/APP Deck Type 11: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type B(1): Base layer of insulation mechanically fastened, top insulation layer adhered with approved asphalt. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Table 3 ACFoam-H, Polytherm, XtraFlex Polyiso, H-Shield, Polytherm-H, ENRGY 3 Minimum 1.5" thick 2 with 4; 6 with 8; 12 with 13 Fastener Density/ft2 1:1.33 ft' Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density (See Roofing Application Standard RAS 117 for fastening details). Top Insulation Laver FescoBoard Minimum'/a" thick Structodek High Density Fiberboard Roof Insulation Minimum %2" thick Insulation Fasteners Fastener Table 3 Density/ft2 N/A : N/A N/A N/A Note: Insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as 'a top layer shall be installed with the polyisocyanurate face down. Base Sheet: (Optional if using ply sheet) One ply of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Ply Sheet: (Optional if using base sheet) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elast6flex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 29 of 65 Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 30 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at,a maximum of 24" o.c. with #8 screws at 6" o.c. System Type B(2): Base layer of insulation mechanically fastened, top layer adhered with approved asphalt. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Laver Insulation Fasteners Fastener Table 3 Density/ft2 ACFoam-II, Polytherm, XtraFlex Polyiso, H-Shield, Polytherm-H, ENRGY-3 Minimum 1.5" thick 2 with 4; 6 with 8; 12 with 1:1.33 ft2 13 Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density (See Roofing he Standard RAS 117 for fastening details). Top Insulation Laver FescoBoard Minimum V thick Structodek High Density Fiberboard Roof Insulation Minimum '/2" thick Insulation Fasteners Fastener Table 3 Density/ft2 N/A N/A N/A N/A Note: Optional top layer of insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as a top layer shall be installed with the polyisocyanurate face down. Base Sheet: (Optional if using ply sheet) One ply of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS HT Base 650 adhered in a full mopping of approved'asphalt applied within the EVT range and at a rate of 20-401bs./sq. Ply Sheet: (Optional if using base sheet) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at'a rate of 20-40 lbs./sq. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 31 of 65 Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -60 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 32 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type B(3): Base layer of insulation mechanically fastened, top layer adhered with approved asphalt. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener Table 3 Density/ft2 ACFoam-II, Polytherm, XtraFlex Polyiso, H-Shield, Polytherm-H, ENRGY 3, Multi -Max FA-3, EnergyGuard Polyiso Insulation, Minimum 2.0" thick 2 with 4; 6 with 8; 12 with 1:1 ftz 13; 15 with 17 Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density (See Roofing Application Standard RAS 117 for fastening details). Top Insulation Laver Insulation Fasteners Fastener Table 3 Density/ft2 DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'/" thick N/A N/A Note: Top layer of insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20- 40 lbs/100 ft. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as a top layer shall be installed with the polyisocyanu rate face down. Primer: (For self -adhering base sheets only) Top insulation is.primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 33 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -75 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 34 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports ate a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type C(1): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Laver Insulation Fasteners Fastener Table 3 : Density/ftz ACFoam-II, Polytherm, XtraFlex Polyiso, H-Shield, Polytherm-H, ENRGY 3, Multi -Max FA-3, EnergyGuard Polyiso Insulation, Minimum 1.0" thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners .and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Laver Insulation Fasteners Fastener Table 3 ; Density/ft2 DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'/a" thick 2 with 4; 6 with 8; 12 with 1:1.78 ftz 13; 15 with 17 Note: All layers of insulation shall be mechanically attached using the fastener, density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Primer: (For self -adhering base sheets only) Top insulation is primed with W13-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 35 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table-4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -45 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 36 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. i9/32" plywood or wood plank attached to structural supports at; a maximum of 24" o.c. with #8 screws at 6" o.c. System Type C(2): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Layer (Optional) Insulation Fasteners Fastener Table 3 Density/ft2 Any approved Polyisocyanurate Listed in Table 2 Minimum 1.5". thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners Fastener Table 3 Density/ft2 Structodek High Density Fiberboard Roof Insulation Minimum'/Z" thick 2 with 4; 6 with 8 1:1.33 W DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum 1/" thick 2 with 4; 6 with 8 1:1.33 ftz Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) Base Sheet: (Optional if using ply sheet in hot asphalt) One ply of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SAV PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered to DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board. *Requires torch -applied ply or cap sheet. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 37 of 65 Ply Sheet: (Optional if using base sheet in hot asphalt) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 38 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 4" o.c. System Type C(3): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Laver (Optional) Insulation Fasteners Fastener Table 3 Density/ft2 Any approved Polyisocyanurate Listed in Table 2 Minimum 1.5" thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Laver Insulation Fasteners Fastener Table 3), Density/ft2 Structodek High Density Fiberboard Roof Insulation Minimum Y2" thick 2 with 4; 6 with 8 1:1.33 ft' DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'14" thick 2 with 4; 6 with 8 1:1.33 ftz Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Primer: (For self -adhering base sheets only) Top insulation is primed with W13-3000. (Optional) Base Sheet: (Optional if using ply sheet in hot asphalt) One ply of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA,V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered to DensDeck Prime or SECUROCK Gypsum -Fiber Roof Board. *Requires torch -applied ply or cap sheet. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 39 of 65 Ply Sheet: (Optional if using base sheet in hot asphalt) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -67.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 40 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports of a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type C(4): 'All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Laver Insulation Fasteners Fastener Table 3 Density/ft2 ACFoam-II, Polytherm, XtraFlex Polyiso, H-Shield, Polytherm-H, ENRGY 3, Multi -Max FA-3, EnergyGuard Polyiso Insulation, Minimum 1.0" thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels. listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Laver Insulation Fasteners Fastener Table 3 Density/ft2 DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'/o" thick 2 with 4; 6 with 8; 12 with 1:1 ft2 13; 15 with 17 Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Primer: (For self -adhering base sheets only) Top insulation is primed with WB-3000. (Optional) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 41 of 65 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA*, self -adhered. *Requires torch -applied ply or cap sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -75 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 42 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type C(5): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Laver (Optional) Insulation Fasteners Fastener Table 3 Density/ft2 Any approved Polyisocyanurate Listed in Table 2 Minimum 1.5" thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Laver Insulation Fasteners Fastener Table 3). Density/ft2 Structodek High Density Fiberboard Roof Insulation Minimum'/2" thick 2 with 4; 6 with 8 1:1.33 ftz DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'/" thick 2 with 4; 6 with 8 1:1.33 ftz Note: All layers of insulation shall be mechanically' attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Base Sheet: (Optional if using ply sheet in hot asphalt) One ply of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. NOA No.: 17-0825.01 MIAMI•DAD,E COUNTY Expiration Date: 09/13/22 ... Approval Date: 05/02/19 Page 43 of 65 Ply Sheet: (Optional if itsing base sheet in hot asphalt) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one to more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -82.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 44 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at, a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type D(1): All layers of insulation and base sheet mechanically fastened. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Laver Any Approved Polyisocyanurate listed in Table 2 Minimum 1" thick Top Insulation Laver (Optional) FescoBoard Minimum'/" thick Structodek High Density Fiberboard Minimum %2" thick Insulation Fasteners Table 3 N/A Insulation Fasteners Table 3 N/A N/A DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board Minimum'/" thick N/A Fastener Density/ft' N/A Fastener Density/ft' N/A N/A N/A Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft., and four fasteners for any insulation board having no dimension greater than 8 ft. Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass Base*, Polyglass G2 Base, , XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below. * Requires torch -applied ply or cap sheet. Fastening: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates,"Dekfast DF-#14-PH3 with Dekfast PLT-H-2-7/8, Polygrip Fasteners 14 with Polygrip Hex Plates or Trufast #14 HD Fastener with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet. NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 45 of 65 Ply Sheet: One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. (Optional) Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 46 of 65 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type D(2): All layers of insulation and base sheet mechanically fastened. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of any of the following insulations: Base Insulation Layer Insulation Fasteners Fastener Table 3 '', Density/ft2 Any; approved Polyisocyanurate Listed in Table 2 Minimum 1" thick N/A N/A Top Insulation Laver (Optional) Insulation Fasteners Fastener Table 3 Density/ft2 FescoBoard Minimum'/4" thick N/A N/A Structodek High Density Fiberboard Minimum W' thick N/A N/A DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board ! Minimum 1/4" thick N/A N/A Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft., and four fasteners for any insulation board having no dimension greater than 8 ft. Base' Sheet: One ply of Elastobase, Elastobase-P, Elastoshield HT, Polyglass Base*, Polyglass G2 Base, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: * Requires torch -applied ply or cap sheet. Fastening: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates spaced 12" o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet. Ply Sheet: One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. (Optional) Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. 1 NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 47 of 65 Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0825.01 MIAMI•DADE couNTY Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 48 of 65 Membrane Type: SBS/APP Deck Type 1: Wood, Non- Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" p.c. with #8 screws at 6" O.C. System Type E(1): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass Base*, Polyglass G2 Base, XtraFlex SBS Glass Base, XtraFlex SBS HT Base 650 fastened to the deck as described below: *Requires torch -applied ply or cap sheet. Fastening #1: (Polyglass Base or Polyglass G2 Base only) Attach base sheet using 11 ga. annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet Fastening #2: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates, Dekfast DF-#14-PH3 with Dekfast PLT-H-2-7/8, Polygrip Fasteners #14 with Polygrip Hex Plates or Trufast #14 HD Fastener with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in frill mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Koo1 APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf; (See General Lini Cation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 49 of 65 Membrane Type: APP Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type E(2): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass Base sheet fastened to the deck as described below: Fastening: Attach base sheet using 11 ga. annular grooved shank and 1" diameter caps spaced 6" o.c. in a 3" lap and 6" o.c. in four equally spaced staggered center rows. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 50 of 65 Membrane Type: SBS Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type E(3): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: Fastening: Attach base sheet using 11 ga. annular grooved shank and 1" diameter caps spaced 6" o.c. in a 3" lap and 6" o.c. in four equally spaced staggered center rows. Membrane: One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 51 of 65 Membrane Type: SBS Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type E(4): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: Fastening: Attach base sheet using Sirnplex MAXX Cap fasteners spaced 9" o.c. in a 2" lap and 12" o.c. in two equally spaced staggered center rows. Membrane: One ply of Polybond, Polyflex G, Polyfresko G or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -52.5 psf, (See General Limitation #7) NOA No.: 17-0825.01 MIAMI•DADE COUNTY Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 52 of 65 Membrane Type: SBS/APP Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type E(5): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastoshield HT, Polybond, Polyflex, Polygl ass Base*, Polyglass G2 Base, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: *Requires torch -applied ply or cap sheet. Fastening: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates spaced 12" o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet. Ply Sheet: One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. (Optional) Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 53 of 65 Membrane Type: SBS/APP Deck Type 1: Wood, Non -Insulated Deck Description: Min. "/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 screws at 6" o.c. System Type E(6): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass Base* or Polyglass G2 Base fastened to the deck as described below: * Requires torch -applied cap sheet. Fastening: Attach base sheet using 11 ga. annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base or one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -60 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 54 of 65 Membrane Type: Deck Type 1: SBS/APP Wood, Non -Insulated Deck Description: Min. 15/32" plywood or -wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type E(7): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass Base* or Polyglass G2 Base fastened to the deck as described below: *Requires torch -applied ply or cap sheet. Fastening: Attach base sheet using 12 ga. annular ring shank nails and 1-5/8" tin -caps attached 8" o.c. in 4" lap and 8" o.c. in four equally spaced staggered center rows. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. I Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt� applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -67.5 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 55 of 65 Membrane Type: SBS/APP Deck Type 1: Wood, Non- Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with 8d ring shank nails at 6" o.c. System Type E(8): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass Base* or Polyglass G2 Base fastened to the deck as described below: *Requires torch -applied ply or cap sheet. Fastening: Attach base sheet using Polygrip Fastener #14 with Polygrip Hex Plates or Dekfast DF-#14- PH3 with Dekfast PLT-H-2-7/8 or OMG Heavy -Duty with OMG 3" Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrae Flat Bottom Plates or Trufast #14 HD with Trufast 3" Metal Insulation Plate or Simplex MAXX Cap Fasteners spaced 10" o.c. in 4" lap and 10" o.c. in three equally spaced staggered center rows. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional)' Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or . XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-401bs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -75.0 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 56 of 65 Membrane Type: APP Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #10 wood screws at 6" o.c. System Type E(9): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass Base* or Polyglass G2 Base sheet fastened to the deck as described below: *Requires torch -applied cap sheet. Fastening: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates spaced 6" o.c. in a 4" lap and 6" o.c. in three equally spaced staggered center rows. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -90.0 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 57 of 65 Membrane Type: SBS Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #10 wood screws at 6" o.c. System Type E(10): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass G2 Base, XtraFlex SBS Glass Base, XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening #1: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates spaced 6" o.c. in a 4" lap and 6" o.c. in three equally spaced staggered center rows. Fastening #2: (Only with asphalt applied cap sheets) Attach base sheet using Trufast #12 DP or Trufast #14 HD fasteners and Trufast 3" Metal Insulation Plates spaced 6" o.c. in a 4" lap and 6" o.c. in three equally spaced staggered center rows. Membrane: One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -90.0 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 58 of 65 Membrane Type: SBS/APP Deck Type 1: Wood, Non -Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports, at a maximum of 24" o.c. with #10 wood screws at 6" o.c. System Type E(11): Base sheet is mechanically attached to roof deck Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass Base* or Polyglass G2 Base fastened to the 'deck as described below: *Requires torch -applied ply or cap sheet. Fastening: Attach base sheet using Polygrip Fastener #14 with Polygrip Hex!Plates or Dekfast DF-#14- PH3 with Dekfast PLT-H-2-7/8 or OMG Heavy -Duty with OMG3" Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrac Flat Bottom Plates or Trufast #14 HD with Trufast 3" Metal Insulation Plate or Simplex MAXX Cap Fasteners spaced 9" o.c. in 4" lap and 9" o.c. in four equally spaced staggered center rows. Ply Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V,'Elastoshield HT, Polybond, (Optional) Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or , One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V,, Elastoshield HT, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT; Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -90.0 psf; (See General Limitation #7) NOA No.: 17-0825.01 MAMMA COUNTY Expiration Date: 09/13/22 Approval Date: 05/01/19 Page 59 of 65 Membrane Type: SBS Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #10 wood screws at 6" o.c. System Type E(12): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of or Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: Fastening: Attach base sheet using Simplex MAXX Cap fasteners spaced 6" o.c. in a 2" lap and 6" o.c. in two equally spaced staggered center rows. Membrane: One ply of Polybond, Polyflex G, Polyfresko G or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: (Optional) Maximum Design Pressure: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. -90.0 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Dater 09/13/22 Approval Date: 05/02/19 Page 60 of 65 Membrane Type: SBS r Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #10 wood screws at 4" o.c. System Type E(13): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One.ply.of Elastobase, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base Fastening: Membrane: Surfacing: (Optional) Maximum Design Pressure: 650 fastened to the deck as described below: i Attach base sheet using Simplex MAXX Cap fasteners spaced 6" ! o.c. in a 2" lap and 6" o.c. in three equally spaced staggered center rows. I One ply of Polybond, Polyflex .G, Polyfresko G or XtraFlex Kooli APP G torch applied. Or One ply of Elastoflex S6 G torch or hot asphalt applied. Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification., I -105.0 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 61 of 65 Membrane Type: SBS Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #8 wood screws at 6" o.c. System Type E(14): 'Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastobase P, Elastoshield HT, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: 11 ga. Annular ring shanked nails and 1-5/8" tin -caps 6" o.c, in 4" lap and 6" o.c. in four equally spaced staggered rows. Tin -caps are primed with PG 100 or XtraFlex 10. Ply Sheet: One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, (Optional) XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoshield HT, Polybond, Polyflex, Polyglass Base, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self -adhered. *Requires torch -applied cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TS G, Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -112.5 psf, (See General Limitation #7) NOA No.: 17-0825.01 MIAMI•DADE COUNTY Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 62 of 65 Membrane Type: APP Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #10 wood screws at 4" o.c. System Type E(15): Base sheet is mechanically attached to roof deck., Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass Base*, Polyglass G2 Base, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: * Requires torch -applied cap sheet. Fastening: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates'spaced 6" o.c. in a 4" lap and 6" o.c. in five equally spaced staggered center rows. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex V G, Elastoflex V G FR, Elastoshield TS G; Elastoshield TS G FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -120.0 psf; (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: OS/02/19 Page 63 of 65 Membrane Type: SBS Deck Type 1: Wood, Non -Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24" o.c. with #10 wood screws at 4" o.c. System Type E(16): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastoshield HT, Polyglass Base*, Polyglass G2 Base, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: * Requires torch -applied cap sheet. Fastening #1: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates spaced 6" o.c. in a 4" lap and 6" o.c. in five equally spaced staggered center rows. Fastening #2: (Only with asphalt applied cap sheets) Attach base sheet using Trufast #12 DP or Trufast #14 HD fasteners and Trufast 3" Metal Insulation Plates spaced 6" o.c. in a 4" lap and 6" o.c. in five equally spaced staggered center rows. Membrane: One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: Install one of the approved surfacing products listed in Table 4 to obtain desired coating or (Optional) required fire classification. Maximum Design Pressure: -120.0 psf, (See General Limitation #7) NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 64 of 65 WOOD DECK SYSTEM LIMITATIONS: 1. A slip sheet is required with Type IV and Type VI when used as a mechanically fastened base or anchor sheet. GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fasteningipatternof the top layer. 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 lbf. insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered. Architect or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 11. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61 G20-3 of the Florida Administrative Code. END OF THIS ACCEPTANCE NOA No.: 17-0825.01 Expiration Date: 09/13/22 Approval Date: 05/02/19 Page 65 of 65