HomeMy WebLinkAboutNOA - CONCRETE ROOF TILE MIAMI-DADE COUNTY
M1AMhQADE PRODUCT CONTROL SECTION
11805 SW 26 Street,Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) Miami,Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade. ov/econom
Crown Building Products of Florida,LLC.
6018 HWY. 72
Arcadia,FL.34266
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section
(In Miami Dade County)and/or the AHJ(in areas other than Miami Dade County)reserve the right to have this product
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements
of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Sanibel Concrete Roof Tile
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA#20-1105.09 and consists of pages 1 through 7.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 21-0420.12
MIAMFDAD`COUNTY Expiration Date: 02/13/24
Approval Date:09/02/21
Page 1 of 7
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub-Category: Roofing Tiles
Material: Concrete
Deck Type: Wood
1. SCOPE
This approves a system using Sanibel Concrete Roof Tile, as manufactured by Crown Building Products of
Florida, LLC., and described in Section 2 of this Notice of Acceptance. For locations where the pressure
requirements, as determined by applicable Building Code does not exceed the design pressure values obtained by
calculations in compliance with RAS 127 using the values listed in section 4 herein. The attachment calculations
shall be done as a moment based system.
2. PRODUCT DESCRIPTION
Manufactured by Test Product
Dimensions
Applicant Specifications Description
Sanibel Concrete Roof L= 17" TAS 112 High profile, interlocking,one-piece, 'S' shaped
Tile W= 13,25" concrete roof the (Type I Class I1I), equipped with
H=3.1" two nail holes. For direct deck or battened nail-on
Thickness: 0.56" (4/12 min slope), mortar set or adhesive set
applications.
Trim Pieces L=varies TAS 112 Accessory trim,concrete roof pieces for use at hips,
W=varies rakes, ridges and valley terminations.
varying thickness Manufactured for each tile profile.
2.1 PRODUCTS MANUFACTURED BY OTHERS
Product Name Product Description Manufacturer
(With Current NOA)
ICP Adhesives Polyset'-" AH-160 Two component polyurethane ICP Adhesives and Sealants, Inc.
foam.adhesive.
TILE BONDTm Roof Tile Adhesive Single component polyurethane DuPont de Nemours, Inc.
foam roof tile adhesive.
Touch `N Seal StormBone One One component polyurethane DAP Foam, Inc.
Component Polyurethane Roof Tile foam adhesive.
Adhesive
2.2 MANUFACTURING LOCATION
2.2.1 Arcadia,FL
CMIAMI�- �=UNW NOA No.:21-0420.12
Expiration Date: 02/13/24
Approval Date:09/02/21
Page 2 of 7
2.3 EVIDENCE SUBMITTED
Test A2eney Test Identifier Test Name/Report Date
PRI Construction Materials ACTI-002-02-01 TAS-112 Sept. 2006
ACTI-002-02-04 TAS-100 Sept. 2006
Redland Technologies 7161-03 Static Uplift Testing Dec. 1991
Appendix III TAS 102&TAS 102(A)
7161-03 Wind Tunnel Testing Dec. 1991
Appendix II TAS 108(Nail-On)
P0402 Withdrawal Resistance Testing of Sept. 1993
screw vs. smooth shank nails
Letter Dated Aug. 1, 1994 Wind Tunnel Testing Aug. 1994
TAS 108 (Nail-On)
P0631-01 Wind Tunnel Testing July 1994
TAS 108 (Mortar Set)
Nutting Engineering 13343.1 Physical Properties June 2006
TAS 112
The Center for Applied 25-7688-3 Static Uplift Testing June 1996
Engineering, Inc. 25-7688-10 TAS 101 (Adhesive Set) July 1996
TAS 101 (Mortar Set)
25-7688-5 Static Uplift Testing June 1996
TAS 102
(3"Headlap,Nails, Direct Deck,New
Construction)
25-7688-4 Static Uplift Testing June 1996
TAS 102
(4"Headlap,Nails, Clips)
Celotex Corporation 520111-3 Static Uplift Testing Dec. 1998
Testing Services 520191-2-1 TAS 101 March 1999
Trinity/ERD Calculations Aerodynamic Multiplier&Restoring Sept. 2006
Moment Due to Gravity
American Test Lab of South RT1028.01-13 TAS 112 11/13/13
Florida RT1206.01-13 Aerodynamic Multiplier&Restoring 02/05/14
Moment Due to Gravity
RT1203.01-18 TAS 112 12/11/18
NEMO ETC,LLC 4c-DPBS-20-LSOTM-01.A- TAS 101 12/17/20
R1
PRI Construction Materials 2002T0003.08 TAS 101 10/06/20
Technologies
NOA No.:21-0420.12
MIAMI•DADE COUNTY Expiration Date: 02/13/24
Approval Date: 09/02/21
Page 3 of 7
3. LIMITATIONS
3.1 Fire classification is not part of this acceptance.
3.2 For mortar or adhesive set tile applications, a static field uplift test shall be perforined in accordance with
TAS 106.
3.3 Applicant shall retain the services of a Miami-Dade County Certified Laboratory to perform quarterly test
in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Miami-Dade Product
Control office for review.
3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed
section 4.1 herein.
3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated
otherwise by the underlayment material manufacturers published literature.
3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with
applicable building code.
3.7 Mechanically attached tile minimum slope 4/12.
3.8 All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code
and Rule 61 G20-3 of the Florida Administrative Code.
4. INSTALLATION
4.1 Crown Building Products of Florida, LLC.'s Sanibel Concrete Roof Tile and its components shall be
installed in strict compliance with Roofing Application Standard RAS 118,RAS 119, and RAS 120.
4.2 Data For Attachment Calculations
Table 1: Average Weight(W) and Dimensions (I x w)
Tile Profile Weight-W(lbf) Length-1 (ft.) Width-w(ft.)
Sanibel Concrete Roof Tile 11.33 1.417 1.104
Table 2: Aerod namic Multipliers -X ft3
Tile 21(ft') X(ft3)
Profile Batten Application Direct Deck Application
Sanibel Concrete Roof Tile 0.289 0.313
Table 3: Restoring Moments due to Gravity-Mg (ft.-lbf)
Tile 2":12 3":12" 4":12" 5":12" 6":12" 7":12" or
Profile greater
Sanibel Battens Direct Battens Direct Battens Direct Battens Direct Battens Direct Battens Direct
Concrete Roof Deck Deck Deck Deck Deck Deck
Tile NIA 9.05 NIA 8.96 8.79 1 8.81 8.60 8.62 8.38 8.40 8.13 8.16
NOA No.: 21-0420.12
[' ropoE c°� Expiration Date: 02/13/24
Approval Date: 09/02/21
Page 4 of 7
Table 4: Attachment Resistance Expressed as a Moment-Mf(ft.-Ibf)
for Nail-On Systems
Tile Fastener Type Direct Deck Direct Deck Battens
Profile (min 15/32" (min. 19132"
plywood) plywood)
Sanibel Concrete 2-10d Ring Shank Nails 28.6 41.2 19.4
Roof Tile 1-1 Od Smooth or Screw Shank Nail 5.1 6.8 2.8
2-10d Smooth or Screw Shank Nails 6.9 9.2 7.3
1 #8 Screw 20.7 20.7 18.1
2#8 Screws 43.2 43.2 29.8
1-1 Od Smooth or Screw Shank Nail (Field 23.1 23.1 19.0
Clip)
1-10d Smooth or Screw Shank Nail (Save 29.3 29.3 24.0
Clip)
2-1 Od Smooth or Screw Shank Nails (Field 27.6 27.6 38.6
Clip)
2-1 Od Smooth or Screw Shank Nails (Save 38.1 38.1 41.8
Clip
Table 5: Attachment Resistance Expressed as a Moment Mf ft-lbf)
for Two Patty Adhesive' Set Systems
Tile Tile Application Minimum Attachment
Profile Resistance
Sanibel Concrete Roof Tile TILE BOND7m Roof Tile Adhesive 192
TILE BONDTm Roof Tile Adhesive 58,
ICP Adhesives Pol set®AH-160 29.34
Touch `N Sea[StormBond® one component) 591
1 See manufacturer component approval for installation requirements.
2 Medium paddy weight of 8 grams between tile and underlayment, paddy weight of 8 grams on overlap of tile of TILE
BOND"m Roof Tile Adhesive
3 Medium paddy weight of 10 grams installed on the center of the back of the tile, second paddy weight of 20 grams on
the underlayment. Place tile so that both paddys combine.
4 Medium paddy weight of 8 grams per paddy of Polyset®AH-160
5 Medium paddy weight of 8 grams between tile and underlayment, paddy weight of 4 grams on overlap of tile of
Touch `N Seal StormBond® one com onent
Table 6: Attachment Resistance Expressed as a Moment-Mr(ft-lbf)
for Single Patty Adhesive'Set Systems
Tile Tile Application Minimum Attachment
Profile Resistance
Sanibel Concrete Roof Tile ICP Adhesives Pol set®AH-160 66.57
ICP Adhesives Polyset®AH-160 38.7'
6 See manufactures component approval for installation requirements
7 Lar a paddy weight of 63 grams of Pol set®AH-160.
8 Lar a paddy weight of 24 grams of Pol sat®AH-160.
NOA No.:21-0420.12
MIAMI-DADE COUNTY Expiration Date: 02/13/24
Approval Date: 09/02/21
Page S of 7
Table 7: Attachment Resistance Expressed as a Moment-Mf(ft.-lbf)
for Mortar Set Systems
Tile Tile Attachment
Profile Application Resistance
Sanibel Concrete Roof Tile Mortar Set9 24.5
9 Tile-Tite Roof Tile Mortar.
5. LABELING
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo as seen below or
following statement: "Miami-Dade County Product Control Approved".
ZA C r
LABEL FOR SANIBEL CONCRETE ROOF TILE
(LOCATED UNDERNEATH OF TILE)
6. BUILDING PERMIT REQUIREMENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6.1.1 This Notice of Acceptance.
6.1.2 Any other documents required by Building Official or Applicable building code in order to
properly evaluate the installation of this system.
NOA No.: 21-0420.12
CMIAMI•oran�cournr Expiration Date: 02/13/24
Approval Date: 09/02/21
Page 6 of 7
PROFILE DRAWING
FASTENER HOLES
Q O
UNDERLOCK�
OVERLOOK
17"
131/4"
SANIBEL CONCRETE ROOF TILE
END OF THIS ACCEPTANCE
�� NOA No.:21-0420.12
M"WAD C UN Expiration Date: 02/13/24
Approval Date: 09/02/21
Page 7 of 7