HomeMy WebLinkAboutNOA - MODIFIED BITUMEN ROOF SYSTEM
NOA No.: 19-0610.05
Expiration Date: 08/29/24
Approval Date: 08/29/19
Page 1 of 6
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
CertainTeed Corporation
20 Moores Road
Malvern, PA 19355
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be
used in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (in
Miami-Dade County) and/or the AHJ (in areas other than Miami-Dade County) reserve the right to have this product or
material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of
such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by
Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable
building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code including
the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: CertainTeed BUR and Modified Bitumen Roofing Membranes
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in
the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials,
use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales,
advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA
shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in
its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall
be available for inspection at the job site at the request of the Building Official.
This NOA consists of pages 1 through 6.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 19-0610.05
Expiration Date: 08/29/24
Approval Date: 08/29/19
Page 2 of 6
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub-Category: Roofing Membranes and Accessories
Material: BUR and Modified Bitumen Roofing
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
SBS: MODIFIED BITUMEN MEMBRANES
Product
Dimensions
Test
Specifications
Product Description
Black Diamond™ Base Sheet
Manufacturing location: #2
36" x 68’7” ASTM D1970
ASTM D4601,
Type I
Self-adhering fiberglass reinforced modified
bitumen base sheet.
Flintlastic Ultra Glass SA
Manufacturing location: #1
39 3/8” x 33’11” ASTM D6163
Self-adhering, fiberglass reinforced, SBS
modified bitumen base/ply sheet.
All Weather/Empire Base
Sheet
Manufacturing location: #1
39 3/8" x 65’10” ASTM D4601,
Type II
Asphalt coated, fiberglass reinforced base sheet.
Flexiglas Base Sheet
Manufacturing location: #1
39 3/8" x 98’9” ASTM D4601,
Type II
Modified Bitumen coated fiberglass base sheet.
Flintlastic Poly SMS Base
Sheet
Manufacturing location: #1
39 3/8" x 64' 3"
ASTM D4601,
Grade S, Type II
UL Type G2
Modified Bitumen coated polyester base sheet.
Flintlastic Ultra Poly SMS
Base Sheet
Manufacturing location: #1
39 3/8” x 32’10” ASTM D6164
Grade S, Type I
SBS modified, polyester reinforced base/ply
sheet.
Flintlastic Base 20
Manufacturing location: #1
39 3/8” x 49’6” ASTM D6163
Grade S, Type I
SBS modified, fiberglass reinforced base/ply
sheet.
Flintlastic Base 20 T
Manufacturing location: #1
39 3/8” x 33’ ASTM D 6163,
Grade S, Type I
Modified Bitumen, coated fiberglass base sheet
for torch application.
Flintlastic FR Cap 30
Manufacturing location: #1
39 3/8" x 32' 10" ASTM D 6163,
Grade G, Type I
Fire resistant, granule surfaced SBS Modified
Bitumen membrane with fiberglass mat
reinforcement for mop applications.
Flintlastic FR Cap 30 T
Manufacturing location: #1
39 3/8” x 32’10” ASTM D 6163,
Grade G, Type I
Granule surfaced SBS Modified Bitumen
membrane with fiberglass mat reinforcement for
torch application.
NOA No.: 19-0610.05
Expiration Date: 08/29/24
Approval Date: 08/29/19
Page 3 of 6
Flintlastic GMS
Manufacturing location: #1
39 3/8" x 32' 10" ASTM D 6164,
Grade G, Type I
Granule surfaced SBS Modified Bitumen
membrane with non-woven polyester mat
reinforcement for mop application.
Flintlastic FR-P
Manufacturing location: #1
39 3/8" x 32' 10" ASTM D 6164,
Grade G, Type I
Granule surfaced SBS Modified Bitumen
membrane with non-woven polyester mat
reinforcement for mop application.
Flintlastic Premium FR-P
Manufacturing location: #1
39 3/8" x 32’ 10” ASTM D 6164,
Grade G, Type II
Fire resistant, granule surfaced SBS Modified
Bitumen Membrane with non-woven polyester
mat reinforcement for mop application.
SBS: SELF-ADHERED MEMBRANES
Product
Dimensions
Test
Specifications
Product Description
Flintlastic SA NailBase
Manufacturing location: #1
39 3/8” x 66’6” ASTM D4601,
Type II
Fiberglass reinforced, SBS modified bitumen
base sheet.
Flintlastic SA PlyBase
Manufacturing location: #1
39 3/8” x 66’6” ASTM D4601,
Grade S, Type II
Self-adhering, fiberglass reinforced, SBS
modified bitumen base/ply sheet.
Flintlastic SA Mid Ply
Manufacturing location: #1
39 3/8” x 32’1” ASTM D 6163,
Grade S, Type I
Self-adhering, polyester reinforced, SBS
modified bitumen ply sheet.
Flintlastic SA Cap
Manufacturing location: #1
39 3/8” x 32’11” ASTM D 6164,
Grade G, Type I
Self-adhering, polyester reinforced, SBS
modified bitumen cap sheet.
Flintlastic SA Cap FR
Manufacturing location: #1
39 3/8” x 32’11” ASTM D 6163,
Grade G, Type I
Self-adhering, fiberglass reinforced, SBS
modified bitumen cap sheet.
APP:MODIFIED BITUMEN MEMBRANES
Product
Dimensions
Test
Specifications
Product Description
Flintlastic APP Base T
Manufacturing location: #1
39 3/8” x 65’ 4” ASTM D6509 Modified Bitumen coated fiberglass base sheet.
Flintlastic STA
Manufacturing location: #1
39 3/8" x 32’10” ASTM D 6222,
Grade S, Type I
Smooth surfaced APP Modified Bitumen
membrane with non-woven polyester mat
reinforcement for torch application.
Flintlastic GTA
Manufacturing location: #1
39 3/8" x 32' 10" ASTM D 6222,
Grade G, Type I
Granule surfaced APP Modified Bitumen
membrane with non-woven polyester mat
reinforcement for torch application.
Flintlastic GTA-FR
Manufacturing location: #1
39 3/8" x 32’ 10" ASTM D 6222,
Grade G, Type I
Granule surfaced APP Modified Bitumen
membrane with non-woven polyester mat
reinforcement for torch application.
NOA No.: 19-0610.05
Expiration Date: 08/29/24
Approval Date: 08/29/19
Page 4 of 6
BUILT-UP ROOFING MEMBRANES
Product
Dimensions
Test
Specifications
Product Description
Glasbase Base Sheet
Manufacturing location: #1
39 3/8" x 98’9” ASTM D4601
Type II
UL Type G2
Asphalt coated, fiberglass base sheet.
Flintglas Ply 4
Manufacturing location: #3
39 3/8" x 164’7” ASTM D2178,
Type IV
UL Type G1
Fiberglass, asphalt impregnated ply sheet.
Flintglas Premium Ply 6
Manufacturing location: #3
39 3/8" x 164’7” ASTM D2178,
Type VI
UL Type G1
Fiberglass, asphalt impregnated ply sheet.
Yosemite Venting Base Sheet
Manufacturing location: #1
39 3/8" x 32’10” ASTM D3909
ASTM D4897,
Type II UL G3
Mineral Surfaced fiberglass reinforced buffer
sheet.
Flintglas MS Cap Sheet
Manufacturing location: #1
39 3/8" x 32’10” ASTM D3909
UL Type G3
Asphalt impregnated and coated inorganic
glass fiber surfaced with mineral granules used
as the top ply in conventional built-up roof
membranes.
MANUFACTURING LOCATIONS:
1. Little Rock, AR
2. Shakopee, MN
3. Shreveport, LA
NOA No.: 19-0610.05
Expiration Date: 08/29/24
Approval Date: 08/29/19
Page 5 of 6
EVIDENCE SUBMITTED:
Test Agency Test Identifier Test Name/Report Date
PRI Construction Materials ASTM D6163 CTC-066-02-01 2011-08-08
Technologies LLC ASTM D6222 CTC-071-02-01 2011-08-08
ASTM D6164 CTC-093-02-01 2011-08-08
ASTM D2178 CTC-123-02-01 2012-03-12
ASTM D4601 CTC-124-02-01 2012-03-12
ASTM D4601 CTC-126-02-01 2012-03-12
ASTM D6509 CTC-116-02-01 2012-04-04
ASTM D6163 CTC-128-02-01 2012-06-08
ASTM D6163 CTC-129-02-01 2012-06-08
ASTM D6164 CTC-131-02-01 2012-06-08
ASTM D6164 CTC-161-02-01 2013-05-09
ASTM D6164 CTC-190-02-01 2013-11-27
ASTM D6163 CTC-319-02-01 2017-08-22
ASTM D4601 CTC-321-02-01 2017-08-22
ASTM D6164 CTC-354-02-01 2018-05-11
Trinity|ERD ASTM D6222 C40050.12.13-R1 2013-12-05
ASTM D6163 C45110.01.14 2014-01-20
ASTM D2178 C47250.03.14 2014-03-26
ASTM D4601 CTR-SC8740.04.15-R2 2015-04-30
ASTM D6163 CTR-SC11145.09.16-5B 2016-09-16
ASTM D3909 CTR-SC11145.09.16-2A 2016-09-19
ASTM D3909 CTR-SC11145.09.16-2B 2016-09-19
ASTM D4601 CTR-SC11145.09.16-3A 2016-09-19
ASTM D4601 CTR-SC11145.09.16-3B 2016-09-19
ASTM D4601 CTR-SC11145.09.16-3C 2016-09-19
ASTM D4897 CTR-SC11145.09.16-4 2016-09-19
ASTM D6163 CTR-SC11145.09.16-5A 2016-09-19
ASTM D6222 CTR-SC11145.09.16-7A 2016-09-19
LABELING:
All membranes and accessories or packaging shall bear the imprint or identifiable marking of the manufacturer's name or
logo, city and state of manufacturing facility, and the following statement: "Miami-Dade County Product Control
Approved" or the Miami-Dade County Product Control Seal as shown below.
NOA No.: 19-0610.05
Expiration Date: 08/29/24
Approval Date: 08/29/19
Page 6 of 6
LIMITATIONS:
1. Fire classification is not part of this acceptance. Refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. CertainTeed BUR and Modified Bitumen Roofing Membranes are designed for use as specified within approved
roofing system NOA assemblies.
3. This acceptance establishes the required physical properties testing and traceability of roofing membrane and
accessory components listed in approved roofing applications. Minimum deck requirements shall be in compliance
with applicable building code. CertainTeed BUR and Modified Bitumen Roofing Membranes shall be installed in
strict compliance with applicable Building Codes, Product Approvals and Manufacturers’ specifications and
guidelines.
4. Change in materials or manufacturing process or location of any of the products listed herein shall be cause for
termination of this Notice of Acceptance.
5. CertainTeed BUR and Modified Bitumen Roofing Membranes may be used with any approved Roof Assembly
Notice of Acceptance listing CertainTeed BUR and Modified Bitumen Roofing Membranes as a component part of
an assembly in the Notice of Acceptance. If CertainTeed BUR and Modified Bitumen Roofing Membranes is not
listed, a request may be made to the Authority Having Jurisdiction (AHJ) or the Miami-Dade County Product
Control Department for approval, provided that appropriate documentation is provided to detail compatibility of the
products, wind uplift resistance, and fire testing results.
6. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE