HomeMy WebLinkAboutLOW SLOPE ROOF SECTION CST. LUCIE WORKS -
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(if a component is not used, identify as "NA")
System Manufacturer: Certainteed
Product Approval No.: FL2533-R24
Design Wind Pressures, From RAS 128 Or Calculations:
Zone 1': -34.6 Zone 1: 6fl•3Zone 2: Zone 3: 1 Q8.4
Max. Design Pressure, from the specific product approval
system:_ -127.5
Deck
Type:
_ VVQod
Gauge Thickness: 1 /811
Slope:
Anchor/Base Sheet & No. df Ply(s):
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheet(s) & No. of Ply(s): FjintjaStiC
Base Sheet Fastener/Bonding Material:
SA
Ply Sheet(s)' & No. of Ply(s):
Ply Sheet Fastener/Bonding Material:
Top Ply: Flintiastir_
Top Ply Fastener/Bonding Material:
SA
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':—"
oc @ Lap, # Rows ! "oe '
Zone 1:—"
oc @ Lap, # Rows ® "oC
Zone 2:--"
oc @ Lap, # Rows 0 `oe
Zone 3:--"
oc @ Lap, # Rows ' oo
Number of Fasteners Per Insulation Board:
Zone 1': Zane 1: Zone 2: Zone 3:
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc. ,
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16..
Flintlastic
Flintlastic
Drip Edge: 3" X 3" Galy Alum
FT.
Parapet
Height
FT.
159
Mean
Roof
Height
ST. LUCIE WORKS
Master Permit No.
Section A (General Information)
Process No.
Contractors Name: Total Home Roofing License# CCC1330489
Job Address 3240 W Lake Dr Ft Pierce, FL 34982
ROOF CATEGORY
O Low Slope ❑ Mechanically Fastened Tile O Mortar/Adhesive Set Tiles
❑ Asphaltic Shingles IaMetal Panel/Shingles QWood Shingles/Shakes
13 Prescriptive BUR-RAS 150
ROOF ROOF TYPE-
0 New roof ❑ Repair O Maintenance C4 Reroofing 13Recovering
- ROOF SYSTEM INFORMATION
Low Slope Roof Area (SF) 2 Steep Sloped Roof Area (SF) 925 Total (SF) _
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains. Include
dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
Michelle Franklin, CFA -- Saint Lucie County Property Appraiser -- All rights reserved.
Building Information
Finished Area: 976 SF
Gross Sketched Area: 1,196 SF
Exterior Data
Building Type:
HC-
Grade:
C-
Year Built:
1971
Effective Year:
1971
No. Units:
I
Primary Wall:
Hardwood Lap
Secondary Wall:
Roof Cover.
Dim Shingle
Roof Structure:
Gable
View:
Frame:
Story Height:
1 Story
Interior Data
Bedrooms:
2
Full Baths:
I
Half Baths:
0
Primary Int Wall:
Drywall
Primary Floors:
Carpet
Avg Hgt/Floor:
0
Heat Type:
FrcdHotAir
Heat Fuel:
ELEC
Electric:
MAXIMUM
A/C %:
100%
Heated %:
100%
Int Sprinkler %:
N/A%
All information is believed to be correct at this time, but is subject to change and is provided without any warranty.
0 Copyright 2022 Saint Lucie County Property Appraiser. All rights reserved.
ST. LUCIE WORKS
Section D (Steep Slope Roof System)
Tri County Metals
Roof System Manufacturer:
Notice of Acceptance Number: FL23302-Rl
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
Zone 1:"74 4Zone 2e: -74 .^Zone 2n-108 one 2r-10�one 3e:108 zone 3r:-128
Deck Tim: I Wood
Roof Slope. -Type Underlayrnent: IPoly Tu
2 :12 Insulation: I NIA
Fire farrier: NIA
RidgeWitladon7 Fastener Type &Spacing: 1 1/4" Ring hank Nails
n/a
Adhesive Type: NIA
Type Cap Sheet: NIA
Mean Roof Height: _ 15' Roof Covering: I Asphalt Shingles
Type & Sim Drip T X 3" Gals Alum
Edge: