HomeMy WebLinkAboutNOA # 15-0721.04AL 'MIANII-DADS COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADINUNISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE OA) www.miamidade.eov/economy
Entegra Roof Tile, LLC
1289 NE 91' Ave
Okeechobee, FL 34972
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Plantation Roof Tile
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA #14-1120.04 and consists of pages 1 through 7.
The submitted documentation was reviewed by Gaspar J Rodriguez.
NOA No.: 15-0721.04
Expiration Date: 12/08/20
Approval Date: 11/05/15
Page 1 of 7
P N®ALL E® STOFFY ArYNITECTS, PA.
AA#003379 ARNN11105
APPROVED ® REVISE & RESUBMIT
® APPROVED AS CORRECTED E] REJECTED
This review is only for gan?ral co, formance writh the design concept oftho
project and general c-o;;Hance with the lmormation given in the contact
d,^.,u ,c�nt�. Cermciians or, nmer� s mado on the shop drawings during
this r eviU11 do iot, raijsve the contractor from compliance with the require-
mwls cf the pblijls and spacifcations. Approval of a specific Hem shall not
include arprow.1 of, n zssaimb'y of which the item is a component Con-
tractor is responsiNe for. Dimensions to be coni3rrned and correlated at the
jib situ; Infumation that partains solely to the fabrication processes orb
the means, methods, techniques, sequences and procedures of constnx-
tion: coordination of the work of ail other trades: and for performing all wwk
in a safe and satisfactory manner.
DATE: r- O BY:
NIIANII-DARE COUNTY
MIAMR _.. PRODUCT CONTROL SECTION
y 11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
\ BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
( ' NOTICE OF ACCEPTANCE (NOA} w�v�r.miamidade.eov/economy
' Entegra Roof Tile, LLC
1289 NE 91h Ave
Okeechobee, FL 34972
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami -Dade County and other areas where allowed by the Authority Having. Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(in Miami -Dade County) and/or the AHJ (in areas other than Miami -Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Plantation Roof Tile
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA #14-1120.04 and consists of pages 1 through 7.
The submitted documentation was reviewed by Gaspar J Rodriguez.
Pt z%
O07, - 04?" A
F girati�n Da a?,tl /20
Approval Date: 11/05/15
Page 1 of 7
ROOFINGASSEMBLYAPPROVAL
Category:
Roofing
Sub -Category:
Roofing Tiles
Material:
Concrete
1. PRODUCT DESCRIPTION
Manufactured by
Dimensions
ILI
- Applicant
Plantation Tile
Length: 16'VV
Width: 13"
Trim Pieces L = varies
W = varies
Varying thickness
2.1. MANUFACTURING LOCATION
1. Okeechobee, FL
2.2 SUBMITTED EVIDENCE:
Test
Product
Specifications
Description
TAS 112
Flat concrete roof tile for direct deck or
battened nail -on, mortar or adhesive set
applications.
TAS 112
Accessory trim, concrete roof pieces for
use at hips, rakes, ridges and valley
terminations. Manufactured for each tile
profile.
Test Agency
Test Identifier
American Test Lab of South
RT0624.05-14
Florida
Redland Technologies
7161-03
Appendix III
The Center for Applied
94-060B
Engineering, Inc.
94-084
Redland Technologies
7161-03
Appendix II
Redland Technologies
Letter Dated Aug. 1, 1994
Redland Technologies P0631-01
Redland Technologies P0402
The Center for Applied Project No. 307025
Engineering, Inc. Test #MDC-76
Walker Engineering, Inc. Calculations
Walker Engineering, Inc. Calculations
MAMMADECOUNTY
Test Name/Report Date
TAS 112 07/03/14
Static Uplift Testing
Dec. 1991
PA 102 & PA 102(A)
Static Uplift Testing
March, 1994
PA 101 (Adhesive Set)
May 1994
(Mortar Set)
Wind Tunnel Testing
Dec. 1991
PA 108 (Nail -On)
Wind Tunnel Testing
Aug. 1994
PA 108 (Nail -On)
Wind Tunnel Testing
July 1994
PA 108 (Mortar Set)
Withdrawal Resistance Testing of
Sept. 1993
screw vs. smooth shank nails
Wind Driven Rain
Oct. 1994
PA 100
Aerodynamic Multiplier
March 1999
April 1999
25-7183
March 1995
25-7094
February 1996
25-7496
April 1996
NOA No.: 15-0721.04
Expiration Date: 12/08/20
Approval Date: 11/05/15
Page 2of7
-, 2.2 SUBMITTED EVIDENCE:
Test Aaeney
Test Identifier
Test Name/Renort
Date
' Walker Engineering, Inc.
Calculations
25-7584
December 1996
25-7804b-8
25-7804-4 & 5
25-7848-6
Walker Engineering, Inc.
Calculations
Two Patty,Adhesive Set System
April 1999
Farabaugh Engineering and
T295-11
TAS-108
10/05/11
w
Testing Inc.
Farabaugh Engineering and
T306-11
TAS-108
10/04/11
Testing Inc.
Farabaugh Engineering and
T279-11
TAS-108
09/23/11
Testing Inc.
3. LIMITATIONS
3.1 Fire classification is not part of this acceptance.
3.2 For mortar or adhesive set tile applications, a static field uplift test shall be performed in accordance with
TAS 106.
3.3 Applicant shall retain the services of a Miami -Dade County Certified Laboratory to perform quarterly test
in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Miami -Dade Product
Control office for review.
3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed
section 4.1 herein.
3.5 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated
otherwise by the underlayment material manufacturers published literature.
3.6 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with
applicable building code.
3.7 All products listed herein shall have a quality assurance audit in accordance with the Florida Building
Code and Rule 61 G20-3 of the Florida Administrative Code.
NOA No.:15-0721.04
Expiration Date: 12/08/20
Approval Date: 11/05/15
Page 3 of 7
r
4. INSTALLATION
4.1 Plantation Roof Tile and its components shall be installed in strict compliance with Roofing Application
StandardRAS 118, RAS 119 and RAS 120.
4.2 Data For Attachment Calculations
Table 1: Average Weight (W) and Dimensions (I x w )
Tile Profile
Weight-W (Ibf)
Length4 (ft)
Wldth-w (ft)
Plantation Tile
11.6
1.375
1.08
Table 2: Aerodynamic Multipliers - A, (ft3)
Tile
Profile
1 (0)
Batten Application
X (ft3)
Direct Deck Application
plantation Tile
0.267
0.289
Table 3: Restoring
Moments due to Gravity - M (ft-Ibf)
Tile
Greater than
Profile
2": 12"
3"• 12"
4"• 12"
5"• 12"
V., 12"
T" 12"
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Deck
Deck
Deck
Deck
Deck
Deck
Plantation
7.22
7.91
6.85
7.79
6.75
7.67
6.61
7.52
6.44
7.32
6.26
7.04
Tile
NOA No.:15-0721.04
Expiration Date:12/08/20
Approval Date: 11/05/15
Page 4 of 7
;1
Table 4: Attachment Resistance Expressed as a Moment - Mr (ft-lbf)
For Nail -On Systems
Tile
Fastener Type
Direct Deck
Direct Deck
Battens
Profile
(Min 15132"
(Min. 19132"
plywood)
plywood)
Plantation Tile
2-10d Ring Shank
30.9
38.1
17.2
Nails
1-10d Smooth or
7.3
9.8
4.9
Screw Shank Nail
2-10d Smooth or
14.0
18.8
7.4
Screw Shank Nails
1 #8 Screw
30.8
30.8
18.2
2 #8 Screw
51.7
51.7
24.4
1-10d Smooth or
24.3
24.3
24.2
Screw Shank Nail
Field Clip)
1-10d Smooth or
19.0
19.0
22.1
Screw Shank Nail
Eave Clip)
2-10d Smooth or
35.5
35.5
34.8
Screw Shank Nails
Field Clip)
2-10d Smooth or
31.9
31.9
32.2
Screw Shank Nails
Eave Clip)
2-10d Ring Shank
50.3
65.5
48.3
Nails'
1 Installation with a W' the
headlap and fasteners are located a minimum of 2%" from the head of tile.
Table 5: Attachment Resistance Expressed as a Moment Mf (ft-Ibf)
For Two Patty Adhesive Set Systems
The Profile
Tile Application
Minimum Attachment
Resistance
Plantation Tile
Adhesive
31.33
2 See manufactures component approval for installation requirements.
3 Flexible Products Company'MeBond Average weights per patty 13.9 grams.
3M'" 2-Component Foam Roof Tile Adhesive AH-160. Average weight pera 8 grams.
Table 6: Attachment Resistance Expressed as a Moment - Mf (ft-Ibf)
For Single Patty Adhesive Set S stems
Tile Profile -
Tile Application
Minimum Attachment Resistance
Plantation Tile
3M' 2-Component Foam Roof Tile Adhesive AH-160
118.94
3M- 2-Component Foam Roof Tile Adhesive AH-160
40.45
4 Large paddy placement of 45 grams of 3Mw 2-Component Foam Roof Tile Adhesive AH-160
5 Medium paddy placement of 24 grams of 3W 2-Component Foam Roof Tile Adhesive AH-160.
NOA No.: 15-0721.04
Expiration Date:12108/20
Approval Date: 11/05/15
)Page 5 of 7
Table 7: Attachment Resistance Expressed as a Moment - Mf(ft-lbf)
for Mortar Set Systems
Tile Profile Tile Application Attachment
I Resistance
See specific mortar manufacturer's Notice of Acceptance.
5. LABELING
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo as seen below or following
statement: "Miami -Dade County Product Control Approved".
OR
�ENTEGRA
PLANTATION ROOF TILE LABEL (LOCATED ON UNDERSIDE OF TILE)
6. BUILDING PERMIT REQUIREMENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6.1.1 This Notice of Acceptance.
6.1.2 Any other documents required by Building Official or Applicable building code in order to properly
evaluate the installation of this system.
NOA No.: 15-0721.04
Expiration Date:12108/20
Approval Date: 11/05/15
Page 6 of 7
' r
PROFILE DRAWING
PLANTATION FLAT CONCRETE TILE
END OF THIS ACCEPTANCE
NOA No.: 15-0721.04
Expiration Date: 12/08/20
Approval Date: 11/05/15
Page 7 of 7