Loading...
HomeMy WebLinkAbout20061003 (1) NOA No. 20-0610.03 Expiration Date: September 22, 2025 Approval Date: September 10, 2020 Page 1 MIAMI–DADE COUNTY, FLORIDA PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION T (786) 315–2590 F (786) 315–2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy CGI WINDOWS and DOORS, INC. 3780 W. 104th Street Hialeah, FL 33018 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami–Dade County RER– Product Control Section to be used in Miami–Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami–Dade County Product Control Section (In Miami–Dade County) and/ or the AHJ (in areas other than Miami–Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami–Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein and has been designed to comply with the Florida Building Code, including the High Velocity Hurricane Zone. DESCRIPTION: Series “HR120-Sentinel” Aluminum Horizontal Sliding Window – L.M.I. APPROVAL DOCUMENT: Drawing No. HR 120LM-NOA Rev A (former W10–18), titled “Series 120 Alum. Horizontal Sliding Window-LM”, sheets 1 through 14 of 14, dated 06/03/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P. E., bearing the Miami–Dade County Product Control Revision stamp with the Notice of Acceptance number and expiration date by the Miami–Dade County Product Control Section. MISSILE IMPACT RATING: Large and Small Missile Impact Resistant LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state, series, and following statement: "Miami–Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/ or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami–Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises and renews NOA No. 17-0918.09 and consists of this page 1 and evidence pages E–1, E–2, E-3, E-4 and E–5, as well as approval document mentioned above. The submitted documentation was reviewed by Ishaq I. Chanda, P. E. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0610.03 Expiration Date: September 22, 2025 Approval Date: September 10, 2020 E – 1 CGI Windows & Doors, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA’s A. DRAWINGS 1. Manufacturer's die drawings and sections. (Submitted under NOA’s No.’s 10–0510.12 and 15–0512.05) 2. Drawing No. W10–18, titled “Series Sentinel 120 Alum Horiz. Sliding Wdw. (L.M.I./ S.M.I.)”, sheets 1, 1.1, 2, 2.1, 3, 3.1, 4 through 11 of 11, dated 03/29/10 with revision “G” dated 05/02/16, prepared by Al–Farooq Corporation, signed and sealed by Javad Ahmad, P.E. B. TESTS 1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 201–94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3) Water Resistance Test, per FBC, TAS 202–94 4) Large Missile Impact Test, per FBC, TAS 201–94 5) Cyclic Wind Pressure Loading, per FBC, TAS 203–94 6) Forced Entry Test, FBC 2411 3.2.1, TAS 202–94 along with marked–up drawings and installation diagram of a series Sentinel 120 aluminum horizontal sliding window, prepared by Certified Test Laboratories, Test Report No. CTLA– 3062W, dated 07/07/15, signed and sealed by Ramesh C. Patel, P.E. 2. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202–94 2) Large Missile Impact Test, per FBC, TAS 201–94 3) Cyclic Wind Pressure Loading, per FBC, TAS 203–94 along with marked–up drawings and installation diagram of a series fixed window, to qualify DuPont “Butacite” PVB interlayer, Duraseal® and Super Spacer® insulating glass spacer, prepared by Certified Test Laboratories, Test Report No. CTLA–3056 WA, dated 03/03/15, signed and sealed by Ramesh C. Patel, P.E. (Submitted under previous NOA No. 15–0512.05) 3. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202–94 2) Large Missile Impact Test, per FBC, TAS 201–94 3) Cyclic Wind Pressure Loading, per FBC, TAS 203–94 along with marked–up drawings and installation diagram of a series project out window, to qualify DuPont “Butacite” PVB interlayer, Duraseal® and Super Spacer® insulating glass spacer, prepared by Certified Test Laboratories, Test Report No. CTLA–3056 WB, dated 03/03/15, signed and sealed by Ramesh C. Patel, P.E. (Submitted under previous NOA No. 15–0512.05). 4. Test reports on: 1) Uniform Static Air Pressure Test, Loading per FBC TAS 202–94 2) Large Missile Impact Test, per FBC, TAS 201–94 3) Cyclic Wind Pressure Loading, per FBC, TAS 203–94 along with marked–up drawings and installation diagram of a series aluminum fixed window, to qualify DuPont “Butacite” PVB interlayer, Duraseal® and Super Spacer® insulating glass spacer, prepared by Certified Test Laboratories, Test Report No. CTLA– 3056 WC, dated 04/16/15, signed and sealed by Ramesh C. Patel, P.E. (Submitted under previous NOA No. 15–0512.05) Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0610.03 Expiration Date: September 22, 2025 Approval Date: September 10, 2020 E – 2 CGI Windows & Doors, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED B. TESTS (CONTINUED) 5. Test reports on: 1) Air Infiltration Test, per FBC, TAS 201–94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202–94 3) Water Resistance Test, per FBC, TAS 202–94 4) Small Missile Impact Test, per FBC, TAS 201–94 5) Cyclic Wind Pressure Loading, per FBC, TAS 203–94 6) Forced Entry Test, FBC 2411 3.2.1, TAS 202–94 along with marked–up drawings and installation diagram of a series “Sentinel” aluminum horizontal sliding window, prepared by Hurricane Test Laboratory, LLC, Test Report No. HTL–0080–0102–10, dated 06/04/10, signed and sealed by Vinu J. Abraham, P. E. (Submitted under NOA No. 10–0510.12) C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 5th Edition (2014), prepared by Al–Farooq Corporation, dated 09/17/15 revised on 05/11/16, signed and sealed by Javad Ahmad, P. E. 2. Glazing complies with ASTM E1300–09 D. QUALITY ASSURANCE 1. Miami–Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 14-0916.10 issued to Kuraray America, Inc. for their “Butacite® PVB Glass Interlayer” dated 04/25/15, expiring on 12/11/16. 2. Notice of Acceptance No. 14–0916.11 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/18. 3. Notice of Acceptance No. 14–0423.15 issued to Eastman Chemical Company (MA) for their “Saflex CP – Saflex and Saflex HP Composite Glass Interlayers with PET Core” dated 06/19/14, expiring on 12/11/18. 4. Notice of Acceptance No. 14-0423.17 issued to Eastman Chemical Company (MA) for their “Saflex Clear and Color Glass Interlayers”, expiring on 05/21/16. F. STATEMENTS 1. Statement letter of conformance, of complying with FBC 5th Edition (2014) and of no financial interest, dated 08/17/15, issued by Al–Farooq Corporation, signed and sealed by Javad Ahmad, P. E. 2. Laboratory compliance letters for Test Report No. CTLA–3062W, dated 07/07/15, issued by Certified Test Laboratories, signed and sealed by Ramesh C. Patel, P. E. 3. Testing Proposal issued by the Product Control Section, dated 04/08/15, signed by Jaime Gascon, P. E., Section Supervisor. 4. Laboratory compliance letters for Test Reports No.’s CTLA–3056 WA, dated 03/03/15, CTLA–3056 WB, dated 03/03/15 and CTLA–3056 WC, dated 04/16/15, all issued by Certified Test Laboratories, all signed and sealed by Ramesh C. Patel, P. E. (Submitted under previous NOA No. 15–0512.05) Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0610.03 Expiration Date: September 22, 2025 Approval Date: September 10, 2020 E – 3 CGI Windows & Doors, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED F. STATEMENTS (CONTINUED) 5. Testing Proposal issued by the Product Control Section, dated 12/16/14, signed by Jaime Gascon, P. E., Section Supervisor. (Submitted under previous NOA No. 15–0512.05) 6. Laboratory compliance letters for Test Report No. HTL–0080–0102–10, issued by Hurricane Test Laboratory, LLC, dated 06/04/10, signed and sealed by Vinu J. Abraham, P. E. (Submitted under NOA No. 10–0510.12) G. OTHERS 1. Notice of Acceptance No. 15–0512.05, issued to CGI Windows & Doors for their Series “Sentinel 120” Aluminum Horizontal Sliding Window – L.M.I., approved on 08/20/15 and expiring on 09/22/20. 2. EVIDENCE SUBMITTED UNDER PREVIOUS NOA A. DRAWINGS 1. Drawing No. W10–18, titled “Series Sentinel 120 Alum Horiz. Sliding Wdw. (L.M.I./ S.M.I.)”, sheets 1, 1.1, 2, 2.1, 3, 3.1, 4 through 11 of 11, dated 03/29/10 with revision “H” dated 09/05/17, prepared by Al–Farooq Corporation, signed and sealed by Javad Ahmad, P.E. B. TESTS 1. None. C. CALCULATIONS 1. None. D. QUALITY ASSURANCE 1. Miami–Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 16-1117.01 issued to Kuraray America, Inc. for their “Trosifol® Ultraclear, Clear and Color PVB Glass Interlayers” dated 01/19/17, expiring on 07/08/19. 2. Notice of Acceptance No. 14–0916.11 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Interlayer” dated 06/25/15, expiring on 07/04/18. 3. Notice of Acceptance No. 17-0712.03 issued to Eastman Chemical Company (MA) for their “Saflex CP – Saflex and Saflex HP Composite Glass Interlayers with PET Core” dated 09/07/17, expiring on 12/11/18. 4. Notice of Acceptance No. 17-0712.05 issued to Eastman Chemical Company (MA) for their “Saflex Clear and Color Glass Interlayers” dated 09/07/17, expiring on 05/21/21. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0610.03 Expiration Date: September 22, 2025 Approval Date: September 10, 2020 E – 4 CGI Windows & Doors, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED F. STATEMENTS 1. Statement letter of conformance to FBC 5th Edition (2014) and FBC 6th Edition (2017), dated 08/30/17, issued by Al–Farooq Corporation, signed and sealed by Javad Ahmad, P. E. G. OTHERS 1. This NOA revises NOA #15-0929.13, expiring on 09/22/20. 3. NEW EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No. HR 120LM-NOA Rev A (former W10–18), titled “Series 120 Alum. Horizontal Sliding Window-LM”, sheets 1 through 14 of 14, dated 06/03/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P. E. B. TESTS 1. Test reports on: 1) Air Infiltration Test, per FBC, TAS 202-94 2) Uniform Static Air Pressure Test, Loading per FBC, TAS 202-94 3) Water Resistance Test, per FBC, TAS 202-94 4) Large Missile Impact Test per FBC, TAS 201-94 5) Cyclic Wind Pressure Loading per FBC, TAS 203-94 6) Forced Entry Test, per ASTM F588 and TAS 202-94 along with marked-up drawings and installation diagram of all CGI Windows and Doors, Inc. and PGT Industries, Inc., representative units listed below and tested to qualify Dowsil 791 and Dowsil 983 silicones, per Proposal #19-1155TP, prepared by Fenestration Testing Laboratory, Inc., Test Reports No.: CGI Windows and Doors Inc. test specimens: FTL-20-2108.1, CGI SH360 Aluminum Single Hung Window (unit 1 in proposal) FTL-20- 2108.2, CGI CA238 Alum. Outswing Casement Window (unit 2 in proposal) FTL-20-2108.3, CGI SGD560 Aluminum Sliding Glass Door (unit 3 in proposal) FTL-20-2108.4, CGI PW410 Aluminum Fixed Window (unit 4 in proposal) and FTL-20-2108.5, CGI SH360 Aluminum Single Hung Window (unit 5 in proposal)all dated 08/24/20 and signed and sealed by Idalmis Ortega, P.E. PGT Industries, Inc. test specimens: FTL-7897, PGT PW5520 PVC Fixed Window (unit 6 in proposal), dated 09/03/14 FTL-20-2107.1, PGT SGD780 Aluminum Sliding Glass Door (unit 7 in proposal) FTL-20- 2107.2, PGT CA740 Alum. Outswing Casement Window (unit 8 in proposal) FTL-20-2107.3, PGT PW7620A Aluminum Fixed Window (unit 9 in proposal) and FTL-20-2107.4, PGT PW7620A Aluminum Fixed Window (unit 10 in proposal) all dated 07/13/20 and signed and sealed by Idalmis Ortega, P.E. C. CALCULATIONS 1. Anchor verification calculations and structural analysis, complying with FBC 7th Edition (2020), dated 03/26/20, prepared by manufacturer, signed and sealed by Anthony Lynn Miller, P.E. 2. Glazing complies with ASTM E1300-04, -09, -12 and -16. Ishaq I. Chanda, P. E. Product Control Unit Supervisor NOA No. 20-0610.03 Expiration Date: September 22, 2025 Approval Date: September 10, 2020 E – 5 CGI Windows & Doors, Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 3. NEW EVIDENCE Continue: D. QUALITY ASSURANCE 1. Miami Dade Department of Regulatory and Economic Resources (RER). E. MATERIAL CERTIFICATIONS 1. Notice of Acceptance No. 19-0305.02 issued to Kuraray America, Inc. for their “Trosifol® Ultraclear, Clear and Color PVB Glass Interlayers”, expiring on 07/08/24. 2. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their “SentryGlas® (Clear and White) Glass Interlayers”, expiring on 07/04/23. 3. Notice of Acceptance No. 17-0712.05 issued to Eastman Chemical Company (MA) for their “Saflex Clear and Color Glass Interlayers” dated 09/07/17, expiring on 05/21/21. 4. Notice of Acceptance No. 18-0301.06 issued to Eastman Chemical Company (MA) for their “Saflex CP – Saflex and Saflex HP Composite Glass Interlayers with PET Core”, expiring on 12/11/23. F. STATEMENTS 1. Statement letters of conformance to FBC 2020(7th Edition), dated 03/26/20, prepared, signed & sealed by Lynn Miller, P. E. 2. Statement from Successor Engineer, adopting another Engineer’s work as his own per FLA 51G915.27-001, signed and sealed on 06/03/20 by Anthony Lynn Miller, P.E. 3. Statement of Lab compliance as part of the test report. G. OTHER 1. This NOA revises and renews NOA No. 17-0918.09 and updates to FBC 2020 (7th Edition) expiring 09/22/25. 2. RER Test proposals #19-1155 dated 01/10/20 approved by Ishaq I. Chanda, P.E.