HomeMy WebLinkAboutNOA - SELF ADHERED ROOF SYSTEM OVER WOOD DECK
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 1 of 34
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
Polyglass USA, Inc.
150 Lyon Drive
Fernley, NV 89408
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Self-Adhered Roof System over Wood Decks
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA# 13-1217.01 and consists of pages 1 through 34.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 2 of 34
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub-Category: Modified Bitumen
Materials SBS/APP/TPO
Deck Type: Wood
Maximum Design Pressure -112.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Dimensions
Test
Specification
Product
Description
Elastobase 65’ 2” x 3’ 3-3/8” ASTM D 6163,
Type I
SBS modified asphalt coated fiberglass reinforced
base sheet.
XtraFlex SBS Glass
Base
65’ 8” x 3’ 3-3/8” ASTM D 6163,
Type I
SBS modified asphalt coated fiberglass reinforced
base sheet.
Polyglass G2 Base 108’ x 36” ASTM D 4601
Type II
Asphalt-coated fiberglass reinforced base sheet
Polyanchor 250’ x 48” ASTM D 4601
Type II
A polymer woven, high performance, synthetic base
sheet.
Elastobase P 65’ 8” x 3’ 3-3/8” ASTM D 6164,
Type I
SBS modified asphalt coated polyester reinforced base
sheet.
Elastoflex SA V FR
(1.5-mm)
66’ 8” x 3’ 3-3/8” ASTM D 6163,
Type I
Self-adhered, fire-rated, fiberglass reinforced, SBS
modified bitumen membrane with a self-adhering back
face and a smooth top surface.
Elastoflex SA V
PLUS FR
66’ 8” x 3’ 3-3/8” ASTM D 6163,
Type I
Self-adhered, fire-rated, fiberglass reinforced, SBS
modified bitumen membrane with a self-adhering back
face and a smooth top surface.
Elastoflex SA V (1.5-
mm)
66’ 8” x 3’ 3-3/8” ASTM D 6163,
Type I
Self-adhered, fiberglass reinforced, SBS modified
bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA V
PLUS
66’ 8” x 3’ 3-3/8” ASTM D 6163,
Type I
Self-adhered, fiberglass reinforced, SBS modified
bitumen membrane with a self-adhering back face and
a smooth top surface.
XtraFlex SBS Base
SA
66’ 8” x 3’ 3-3/8” ASTM D 6163,
Type I
Self-adhered, fiberglass reinforced, SBS modified
bitumen membrane with a self-adhering back face and
a smooth top surface.
Elastoflex SA P FR 32’ 10” x 3’ 3-3/8” ASTM D 6164,
Type I
Self-adhered, fire-rated, polyester reinforced, SBS
modified bitumen membrane with a self-adhering back
face and a granule top surface.
XtraFlex SBS G SA 32’ 10” x 3’ 3-3/8” ASTM D 6164,
Type I
Self-adhered, fire-rated, polyester reinforced, SBS
modified bitumen membrane with a self-adhering back
face and a granule top surface.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 3 of 34
Elastoflex SA P 32’ 10” x 3’ 3-3/8” ASTM D 6164,
Type I
Self-adhered, fiberglass reinforced, SBS modified
bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
XtraFlex APP S 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
Polybond 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
Polyflex G 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a granule top surface.
Polyflex SA P 32’ 10” x 3’ 3-3/8” ASTM D 6222,
Type I
Self-adhered, polyester reinforced, APP modified
bitumen membrane with a self-adhering back face and
a granule top surface.
Polyflex SA P FR 32’ 10” x 3’ 3-3/8” ASTM D 6222,
Type I
Self-adhered, fire-rated, polyester reinforced, APP
modified bitumen membrane with a self-adhering back
face and a granule top surface.
XtraFlex APP G SA 32’ 10” x 3’ 3-3/8” ASTM D 6222,
Type I
Self-adhered, fire-rated, polyester reinforced, APP
modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyfresko G SBS SA 32’ 10” x 3’ 3-3/8” ASTM D 6164,
Type I
Self-adhered, fiberglass reinforced, SBS modified
bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko G SBS SA
FR
32’ 10” x 3’ 3-3/8” ASTM D 6164,
Type I
Self-adhered, fire-rated, fiberglass reinforced, SBS
modified bitumen membrane with a self-adhering back
face and a granule top surface.
Polyfresko G APP SA 32’ 10” x 3’ 3-3/8” ASTM D 6222,
Type I
Self-adhered, polyester reinforced, APP modified
bitumen membrane with a self-adhering back face and
a granule top surface.
Polyfresko G APP SA
FR
32’ 10” x 3’ 3-3/8” ASTM D 6222,
Type I
Self-adhered, fire-rated, polyester reinforced, APP
modified bitumen membrane with a self-adhering back
face and a granule top surface
PolyKool 32’ 10” x 3’ 3-3/8” ASTM D6222
Type I
Self-adhered, polyester reinforced, APP modified
bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
XtraFlex Kool APP S
SA
32’ 10” x 3’ 3-3/8” ASTM D6222
Type I
Self-adhered, polyester reinforced, APP modified
bitumen membrane with a self-adhering back face and
a white film laminate on the top surface.
Polyglass APP Base 65’ 8” x 3’ 3-3/8” ASTM D 6509
Type I
APP modified asphalt coated fiberglass reinforced
base sheet.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 4 of 34
PG325 Cold Process
Adhesive
1, 3, 5, 50, 55 gal. or
tube
ASTM D3019
Type III
A fibered cold process adhesive for use with roll or
BUR roofing.
PG100 Asphalt Primer 1, 3, 5, 50, 55 gal,
tube or 17 oz. spray
can
ASTM D41 A penetrating solution of solvent and a blend of
selected asphalts used to promote adhesion.
XtraFlex 10 Asphalt
Primer
1, 3, 5, 50, 55 gal,
tube or 17 oz. spray
can
ASTM D41 A penetrating solution of solvent and a blend of
selected asphalts used to promote adhesion.
PG350 Mod Bit
Adhesive
1, 3, 5, 50, 55 gal. or
tube
ASTM D3019
Type III
A fibered rubberized adhesive designed for use with
modified bitumen membranes.
PG400 Plastic Roof
Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586
ASTM D3409
A thick, fibered, rubberized flashing cement for use in
dry or damp conditions.
PG425 Wet/Dry Roof
Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586
ASTM D3409
A thick, fibered, rubberized flashing cement for use in
dry or damp conditions.
PG450 Flashing
Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586 A thick, fibered, rubberized flashing cement.
PG500 MB Flashing
Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586 A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
Polyplus 35 Premium
Mod Bit Adhesive
1, 3, 5, 50, 55 gal. or
tube
ASTM D3019
Type III
A fibered rubberized adhesive designed for use with
modified bitumen membranes.
XtraFlex 35 Premium
Mod Bit Adhesive
1, 3, 5, 50, 55 gal. or
tube
ASTM D3019
Type III
A fibered rubberized adhesive designed for use with
modified bitumen membranes.
Polyplus 45 Premium
Flashing Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586 A thick, fibered, rubberized flashing cement.
Polyplus 50 Premium
MB Flashing Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586 A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
XtraFlex 50 Premium
Modified Wet/Dry
Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586 A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
Polyplus 55 Premium
Modified Flashing
Cement
1, 3, 5, 50, 55 gal. or
tube
ASTM D4586 A mastic compound for use as a roof flashing
adhesive.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 5 of 34
APPROVED INSULATIONS:
TABLE 2
Product Name Product Description Manufacturer
(With Current NOA)
Polytherm-H Polyisocyanurate foam insulation Polyglass USA, Inc.
Polytherm Polyisocyanurate foam insulation Polyglass USA, Inc.
ACFoam-II Polyisocyanurate foam insulation Atlas Roofing Corp
ACFoam-III Polyisocyanurate foam insulation Atlas Roofing Corp
High Density Wood Fiberboard Wood fiber insulation board Generic
DensDeck, DensDeck Prime Gypsum insulation board Georgia-Pacific Gypsum LLC
H-Shield Polyisocyanurate foam insulation Hunter Panels, LLC
H-Shield CG Polyisocyanurate/perlite composite insulation Hunter Panels, LLC
ENRGY-3 Polyisocyanurate foam insulation Johns Manville Corp.
Fesco Board Expanded mineral fiber Johns Manville Corp.
Multi-Max FA-3 Polyisocyanurate foam insulation Rmax Operating, LLC.
SECUROCK Gypsum-Fiber Roof Board Fiber reinforced coverboard United States Gypsum
Corporation
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 6 of 34
APPROVED FASTENERS:
TABLE 3
Fastener
Number
Product
Name
Product
Description
Dimensions
Manufacturer
(With Current NOA)
1. Dekfast Fasteners 12, 14 &
15 HS
Insulation fastener for wood,
steel and concrete decks
SFS Intec, Inc.
2. Dekfast Galvalume Steel
Hex Plate
Galvalume hex stress plate. 2 7/8" x
3 ¼”
SFS Intec, Inc.
3. #14 Roofgrip Insulation and membrane
fastener
Various OMG, Inc.
4. Flat Bottom Metal Plate A2-SS aluminized steel plate 3" square OMG, Inc.
5. Trufast #14 HD Fastener Insulation fastener for steel and
wood decks
Altenloh, Brinck & Co.
U.S., Inc.
6. Trufast 3” Metal Insulation
Plate
Round Galvalume AZ50 steel
plate
3.23 round
3" round
Altenloh, Brinck & Co.
U.S., Inc.
7. Polygrip Fasteners #12, #14
& #15
Insulation fastener for wood,
steel and concrete decks
Various Polyglass USA, Inc
8. Polygrip Hex Plates Galvalume hex stress plate. 2 7/8" x
3 ¼”
Polyglass USA, Inc
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 7 of 34
APPROVED SURFACING:
TABLE 4
Product
Name
Product
Description
Application
Rate Specification Manufactur
er
PG200 Non-Fibered Roof Coating A non fibered asphaltic coating used
to add life and rejuvenate existing
BUR roofing substrates.
1½-2 gal/sq TAS 140 Polyglass
USA, Inc.
XtraFlex 20 Bituminous Roof
Coating
A non fibered asphaltic coating used
to add life and rejuvenate existing
BUR roofing substrates.
1½-2 gal/sq TAS 140 Polyglass
USA, Inc.
PG300 Fibered Roof Coating An asphalt cutback fibered roof
coating. May be applied by brush or
spray equipment to rejuvenate aged
BUR
1½-2 gal/sq ASTM D4479 Polyglass
USA, Inc.
XtraFlex Bituminous Roof
Coating Fibered
An asphalt cutback fibered roof
coating. May be applied by brush or
spray equipment to rejuvenate aged
BUR
1½-2 gal/sq ASTM D4479 Polyglass
USA, Inc.
PG600 Non-Fibered Aluminum
Roof Coating
Non-fibered aluminum roof coating. ½-1 gal/sq ASTM D2824
Type I
Polyglass
USA, Inc.
PG650 Fibered Aluminum Roof
Coating
Fibered aluminum roof coating. 1½-2 gal/sq ASTM D2824
Type III
Polyglass
USA, Inc.
PG700 Elastomeric Roof Coating A premium white elastomeric acrylic
based roof coating (water-based). A
polyester fabric may be used for
reinforcement with this coating.
1-1½ gal/sq ASTM D6083 Polyglass
USA, Inc.
PG800 Non-Fibered Asphalt
Emulsion Roof Coating
An asphalt base, un-fibered clay
emulsion
3 gal/sq in
two coats
ASTM D1227 Polyglass
USA, Inc.
XtraFlex 80 Emulsion Roof
Coating
An asphalt base, un-fibered clay
emulsion
3 gal/sq in
two coats
ASTM D1227 Polyglass
USA, Inc.
PG850 Fibered Asphalt Emulsion
Roof Coating
An asphalt base, fibered clay
emulsion
3 gal/sq in
two coats
ASTM D1227 Polyglass
USA, Inc.
Polyplus 65 Premium Fibered
Aluminum Roof Coating
Fibered aluminum roof coating. 1½-2 gal/sq ASTM D2824
Type III
Polyglass
USA, Inc.
XtraFlex 65 Aluminum Roof
Coating Fibered
Fibered aluminum roof coating. 1½-2 gal/sq ASTM D2824
Type III
Polyglass
USA, Inc.
Polyplus 60 Premium Non-
Fibered Aluminum Roof Coating
Non-fibered aluminum roof coating. ½-1 gal/sq ASTM D2824
Type I
Polyglass
USA, Inc.
XtraFlex 60 Aluminum Roof
Coating
Non-fibered aluminum roof coating. ½-1 gal/sq ASTM D2824
Type I
Polyglass
USA, Inc.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 8 of 34
APPROVED SURFACING:
TABLE 4
Product
Name
Product
Description
Application
Rate Specification Manufactur
er
Polybrite 70 Premium Grade
Elastomeric Roof Coating
A premium white elastomeric acrylic
based roof coating (water-based). A
polyester fabric may be used for
reinforcement with this coating.
1-1½ gal/sq ASTM D6083 Polyglass
USA, Inc.
XtraFlex 70 Premium Acrylic FR
Roof Coating
A premium white elastomeric acrylic
based roof coating (water-based). A
polyester fabric may be used for
reinforcement with this coating.
1-1½ gal/sq ASTM D6083 Polyglass
USA, Inc.
Polybrite 90 High Solids Silicone
Roof Coating
A premium grade high solids, single
component, moisture cure, fluid
applied silicone coating
1.25 gal/sq ASTM D6694 Polyglass
USA, Inc.
XtraFlex SRC 9600 High Solids
Silicone Roof Coating
A premium grade high solids, single
component, moisture cure, fluid
applied silicone coating
1.25 gal/sq ASTM D6694 Polyglass
USA, Inc.
Polybrite 95 Silicone Roof
Coating
A single component, solvent,
moisture cure silicone coating.
1.25 gal/sq ASTM D6694 Polyglass
USA, Inc.
XtraFlex SRC 8000 Silicone Roof
Coating
A single component, solvent,
moisture cure silicone coating.
1.25 gal/sq ASTM D6694 Polyglass
USA, Inc.
Gravel To be installed in a flood coat of
approved asphalt at 60 lbs/sq
400 lbs/sq N/A Generic
Slag To be installed in a flood coat of
approved asphalt at 60 lbs/sq
300 lbs/sq N/A Generic
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 9 of 34
EVIDENCE SUBMITTED:
Test Agency Test Name/Report Report No.
Date
Factory Mutual Research 4470 2W7A7.AM 08.04.94
Corporation 4450 2D5A9.AM 06.22.99
4470 3001334 02.15.00
4470 3000857 01.12.00
4470 3004091 01.12.00
4470 3012321 07.29.07
4450 3014751 08.27.03
4450 3019317 06.30.04
4470 3014692 08.05.03
Trinity | ERD TAS 114 11752.09.99-1 02.08.00
TAS 114 02764.09.05 09.09.05
TAS 114 02762.03.05 03.30.05
TAS 117(B)-ASTM D903 020841.06.04 06.02.04
TAS 114 P1734.07.06-R1 02.27.07
TAS 114 P1738.02.07 02.05.07
TAS 114 P1739.01.07 01.23.07
TAS 117(B)-ASTM D6862 C8500SC.11.07 11.30.07
ASTM D6164 / ASTM D6222 P10490.08.08 08.13.08
ASTM D6164 / ASTM D6222 P10490.10.08-R1 10.03.08
ASTM D6222 P7400.03.08-R2 10.09.08
TAS 114(D) – ASTM D1876 P10070.10.08 10.09.08
ASTM D6222 P10490.10.08-2 10.30.08
FM 4470 & TAS 114 P33970.03.11 03.15.11
ASTM D6163 / ASTM D 4601 P33960.03.11 03.15.11
TAS 114 & TAS 117 (B) 11757.12.00-1-R1 04.29.13
TAS 114 & TAS 117 (B) 11757.04.01-1-R1 04.30.13
ASTM D6164 P37590.07.13-1 07.02.13
ASTM D6164 P37590.03.13-3A 03.06.13
ASTM D6163 P37590.03.13-2-R1 02.05.13
ASTM D6222 P37590.09.13 09.12.13
ASTM D4601 / TAS 117 P45940.09.13 09.04.13
TAS 114 & FM 4474 P41630.08.13 08.06.13
TAS 114 (H) P13760.09.09 09.10.09
ASTM D4601 / TAS 117 P45970.05.14 05.12.14
PRI Construction Materials
Technologies
ASTM D6222 PUSA-061-02-02 01.28.08
ASTM D6222 PUSA-062-02-02 12.04.08
ASTM D6163 PUSA-064-02-02 02.27.08
ASTM D6694 PUSA-134-02-01 05.16.14
ASTM D6694 PUSA-135-02-01 05.16.14
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 10 of 34
APPROVED ASSEMBLIES:
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with #8 wood screws at 6” o.c..
System Type A(1): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Polyglass G2 Base, Polyflex*, XtraFlex APP
S*, Polybond* or GAFGLAS #75 fastened to the deck as described below:
*with OMG fasteners and Flat Bottom Metal Plates.
Fastening #1: Attach base sheet using 11 ga. annular ring shank and 1-5/8” diameter tin caps spaced 8” o.c.
in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet.
Fastening #2: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
14 with Galvalume Steel Hex Plates or Polygrip Fasteners #14 with Polygrip Hex Plates or
Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plates spaced 12” o.c. in a 4” lap
and 12” o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Layer (Optional) Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1” thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board
Minimum ¼” thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 11 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See general limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 12 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with #8 wood screws at 6” o.c .
System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P, Polyglass G2 Base, Polyflex,
XtraFlex APP S or Polybond fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12”
o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Layer (Optional) Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1” thick N/A N/A
Top Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board
Minimum ¼” thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 13 of 34
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-60 psf; (See general limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 14 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with 8d common nails at 4” o.c.
or #8 wood screws at 6” o.c .
System Type A(3): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga. Annular ring shank and 1-5/8” diameter tin caps spaced 8” o.c.
in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet.
One of more of the following:
Base Insulation Layer (Optional) Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1” thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Dens Deck, Dens Deck Prime, SECUROCK Gypsum-Fiber Roof Board
Minimum ¼” thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 15 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See general limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 16 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank fastened at 24” spans with #8 wood screws at 6” o.c.
System Type A(4): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened as below:
Fastening: 12 ga. Annular ring shank nails and 1-5/8” tin-caps attached 6” o.c. in 4” lap and 6” o.c. in four
equally spaced staggered rows.
Base Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, H-Shield CG, Multi-Max FA-3, ENRGY 3
Minimum 1” thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet with Millennium One-Step Foamable Adhesive applied
over rows of tin-caps in continuous rows 7” o.c. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-60 psf; (See general limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 17 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with 8d common nails or wood
screws at 4” o.c.
System Type C(1): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following
Base Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5” thick N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Approved High Density Wood Fiberboard
Minimum ½” thick 1 1:1.33 ft²
DensDeck
Minimum ¼” thick 1 1:1.33 ft²
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 18 of 34
coating or required fire classification.
Maximum Design
Pressure:
-67.5 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 19 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with 8d common nails at 4” o.c.
System Type C(2): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5” thick N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Approved High Density Wood Fiberboard
Minimum ½” thick 1 1:1.33 ft²
DensDeck
Minimum ¼” thick 1 1:1.33 ft²
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 20 of 34
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-67.5 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 21 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with wood screws at 6” o.c.
System Type C(3): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following:
Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
ENRGY 3, H-Shield, Polytherm-H, ACFoam-II, Polytherm
Minimum 1.5” thick 1, 5 or 7 1:1.33 ft²
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-82.5 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 22 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with #8 wood screws at 6” o.c.
System Type D(1): All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1” thick N/A N/A
Top Insulation Layer (Optional) Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Fesco Board
Minimum ¾” thick N/A N/A
Approved High Density Wood Fiberboard
Minimum ½” thick N/A N/A
DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board
Minimum ¼” thick N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One or more plies of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor
fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners #14 with Polygrip Hex Plates
or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plates spaced 12” o.c. in a 4” lap
and 12” o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 23 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 24 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with #8 wood screws at 6” o.c.
System Type D(2): All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Layer Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1” thick N/A N/A
Top Insulation Layer (Optional) Insulation Fasteners
(Table 3)
Fastener
Density/ft2
Fesco Board
Minimum ¾” thick N/A N/A
Approved High Density Wood Fiberboard
Minimum ½” thick N/A N/A
DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Roof Board
Minimum ¼” thick N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One or more plies of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor
fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12”
o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 25 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-60 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 26 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with 8d common nails at 4” o.c.
or #8 wood screws at 6” o.c.
System Type E(1): Base sheet is mechanically attached to roof deck.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8” diameter tin caps spaced 8”
o.c. in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See General limitation #7.).
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 27 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with #8 wood screws at 6” o.c.
System Type E(2): Base sheet is mechanically attached to roof deck.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening #: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
#14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners #14 with Polygrip Hex
Plates or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plates spaced 12” o.c. in a
4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-
adhered.
Or
One ply of Polyflex G, torch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-60 psf; (See General limitation #7.).
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 28 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with 8d ring shank nails at 6”
o.c. at edges and intermediate supports.
System Type E(3): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Polyglass APP Base, Elastobase (Poly/Sand) sheet fastened to the deck as described
below:
Fastening: Attach base sheet using 11 ga. annular grooved shank and 1” diameter caps spaced 6” o.c. in a
3” lap and 6” o.c. in four equally spaced staggered center rows.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyfresko G SBS SA,
Polyfresko G SBS SA FR, Polyflex SA P, Polyflex SA P FR, XtraFlex APP G SA, Polyfresko
G APP SA, Polyfresko G APP SA FR, PolyKool or XtraFlex Kool APP S SA self-adhered.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See General Limitation #7)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 29 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with 8d common nails at 4” o.c.
or #8 wood screws at 6” o.c
System Type E(4): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12”
o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-adhered.
Or
One ply of Polyflex G, torch-applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See General Limitation #7)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 30 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24” spans with 8d common nails at 4” o.c.
or #8 wood screws at 6” o.c .
System Type E(5): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8” diameter tin caps spaced 8”
o.c. in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-adhered.
Or
One ply of Polyflex G, torch-applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See General Limitation #7)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 31 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24” o.c. and to blocking
members spaced 48” o.c. with TruFast TP #10x2-7/8” screws spaced 6” o.c.
System Type E(6): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8” diameter tin caps spaced 4”
o.c. in a 4” lap and 4” o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Elastoflex SA P, Elastoflex SA P
FR or XtraFlex SBS G SA, self-adhered.
Or
One ply of Polyflex G, torch-applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-97.5 psf; (See General Limitation #7)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 32 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24” o.c. and to blocking
members spaced 48” o.c. with #10x3” wood screws spaced 6” o.c.
System Type E(7): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: Attach base sheet using 12 ga. ring shank nails and tin caps spaced 4” o.c. in a 4” lap and 4”
o.c. in four equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Elastoflex SA P, Elastoflex SA P
FR or XtraFlex SBS G SA, self-adhered.
Or
One ply of Polyflex G, torch-applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-112.5 psf; With Elastoflex SA V PLUS, XtraFlex SBS Base SA or Elastoflex SA V PLUS FR
(See General limitation #7.)
-97.5 psf; With Elastoflex SA V(1.5-mm) or Elastoflex SA V FR(1.5-mm) (See General
limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 33 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non-Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24” o.c. with #8x3” wood
screws spaced 6” o.c.
System Type E(8): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: 12 ga. annular ring shanked nails and 1-5/8” tin-caps 6” o.c. in 4” lap and 6” o.c. in four equally
spaced staggered rows. Tin-caps are primed with PG100 Asphalt Primer or XtraFlex 10
Asphalt Primer.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self-adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self-adhered.
Or
One ply of Polyflex G, torch-applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-112.5 psf; With Elastoflex SA V PLUS, XtraFlex SBS Base SA or Elastoflex SA V PLUS FR
(See General limitation #7.)
-97.5 psf; With Elastoflex SA V(1.5-mm) or Elastoflex SA V FR(1.5-mm) (See General
limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 34 of 34
WOOD DECK SYSTEM LIMITATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product
Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the
top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam
insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using
spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one
at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener
spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or
Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal
resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing
Application Standard RAS 117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE