HomeMy WebLinkAboutEvaluation Report ( Asphalt Roof Shingles0
NEMO I etc.
Certificate of Authorization #32455
353 Christian Street, Unit #13
Oxford, CT 06478
(203) 262-9245
ENGINEER EVALUATE TEST CONSULT
M IIATION RFPCIF
Owens Corning Evaluation Report 037940.02.12-R11
One Owens Corning Parkway FL10674-R16
Toledo, OH 43659 Date of Issuance: 02/06/2012
(140) 404-7829 Revision 11: 12/11/2020
SCOPE:
This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for
compliance with the 7th Edition (2020) Florida Building Code sections noted herein.
DESCRIPTION: Owens Corning Asphalt Roof Shingles
LABELING: Labeling shall be in accordance with the requirements of the Accredited Quality Assurance Agency noted
herein and FBC 1507.2.7.1 / R905.2.6.1
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance or production facility location(s) changes, or Code provisions that relate to the product(s) change.
Acceptance of our Evaluation Reports by the named client constitutes agreement to notify NEMO ETC, LLC of any
changes to the product(s), the Quality Assurance or the production facility location(s). NEMO ETC, LLC requires a
complete review of its Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Florida Product Approval Number (FL#) preceded by the words "NEMO Ietc. Evaluated" may be
displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its
entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 10.
Prepared by:
Robert J.M. Nieminen P.E.
�` -•sue:ss ?u'
sA .:tis; T= The facsimile seal appearing was authorized by Robert
.. r,,Sg� `c � �• Nieminen, P.E. on 12/11/2020. This does not serve as an
Florida.Registration No. 59166, Florida DCA ANE1983
,:''j�. ° i�t�„ electronically signed document.
CERTIFICATION OF INDEPENDENCE:
1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEMO ETC, LLC is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
S. This is a building code evaluation. Neither MEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
02018 NEMO.ETC, LLC
ONEMOletc.
ROOFING SYSTEMS EVALUATION:
Product Category:
Roofing
Sub -Category:
Asphalt Shingles
Compliance Statement:
Owens Corning Asphalt
Roof Shingles, as produced
by Owens Corning, have
demonstrated compliance with the following sections of the 7` Edition (2020) Florida Building Code through
testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and
Limitations / Conditions of Use set forth herein.
STANDARDS:2.
Section
Property
Standard
Year
1507.2.4, R905.2.3
Physical Properties
ASTM D1970
2015
1507.2.5, R905.2.4
Material standard
ASTM D3462
2010
1507.2.7.1, R905.2.6.1
Wind Resistance
ASTM D3161
2016
1507.2.7.1, R905.2.6.1
Wind Resistance
ASTM D7158
2019
3. REFERENCES:
gaiitf
Examination
Reference
Date
Owens Corning
Declaration
Equivalency Declaration
08/06/2019
PRI (TST5878)
ASTM D1970
OCF-382-02-01
10/24/2017
UL LLC (CER9626)
Physicals & Wind Resistance
File R2453, Vol. 3
02/15/2007
UL LLC (CER9626)
Physicals & Wind Resistance
20120516-112453
05/16/2012
UL LLC (TST9628)
Physical Properties
06CA20263
04/18/2006
UL LLC (TST9628)
Wind Resistance
11CA34308
02/18/2012
UL LLC (TST9628)
Physicals & Wind Resistance
4786093137
02/01/2014
UL LLC (TST9628)
Wind Resistance
4786126532
02/10/2014
UL LLC (TST9628)
Physical Properties
Classification letter
02/13/2014
UL LLC (TST9628)
Physical Properties
Classification letter
10/02/2015
PRI (QUA9110)
Quality Control
Service Confirmation
04/05/2020
PRI (QUA9110)
Quality Control
Florida BCIS
Current
4. '••DDESCRIPTION:
TABLE 1: ASPHALT SHINGLE COMPONENTS
Type
Product
Plant(s)
Material
Standard
Description
Starter Strip Shingle
H TX, OR
Accessory
ASTM D3462
starter strips for asphalt roof shingles
Starter Strip Plus
MN, OR
SRS To Shield Starter
MN, OR
Starter
Starter Shingle Roll
NH
ASTM D1970
mineral -surfaced, fiberglass -reinforced,
self -adhering SBS modified bitumen starter
Strips
Supreme °
GA, CA, CO, I -TX, NJ, OH,
TN, OR, IL
ASTM D3462
fiberglass reinforced 3-tab asphalt
roof shingles
Berkshire'
MN
ASTM D3462
fiberglass reinforced, 4-tab asphalt
roof shingles
Duration' Premium
CA, OR
Duration' Premium COOL
CA
Asphalt
Shingles
ASTM D3462
fiberglass reinforced, laminated
asphalt roof shingles
TruDefinition' Duration'
IN, CA, CO, I -TX, FL, NJ, OH,
MN, OR, GA, IL, TN
TruDefinition' Duration'
Designer Color Collection
Oakridge
GA, IN, CA, CO, H-TX, I -TX,
FL, NJ OH, TN
TruDefinition' Oakridge'
H-TX, I -TX
WeatherGuard' HP
TN
MEMO ETC, LLC Evaluation Report 037940.02.12-1111
Certljicate of Authorization #32455 7`" EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116
Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020
Page 2 of 20
ONEMOletc.
TABLE 1: ASPHALT SHINGLE COMPONENTS
Type
Product
Plant(s)
Material
Standard
Description
Berkshire" Hip and Ridge
MN
Shingles with Sealant
DuraRidge® Hip and Ridge
MN
Hip and
fiberglass reinforced, hip and ridge
Ridge
Shingles with Sealant
ASTM D3462
asphalt roof shingles
ProEdge®
GA, CA, OH, OR
Shingles
WeatherGuard® HP Hip and
TN
Ridge Shingles
S. LimITATIONS:
5.1 This is a building code evaluation. Neither NEMO ETC, LLC nor Robert Nieminen, P.E. are, in any way,, the Designer
of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting
or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC High Velocity Hurricane Zone jurisdictions (i.e., Broward and Miami -
Dade Counties).
5.3 This Evaluation Report pertains to above -deck roof components. Roof decks and structural members shall be in
accordance with FBC requirements to the satisfaction of the Authority Having Jurisdiction.
5.4 This Evaluation Report does not include evaluation of fire classification. Refer to FBC 1505 for requirements and
limitations regarding roof assembly fire classification. Refer to FBC 2603 for requirements and limitations
concerning the use of foam plastic insulation.
5.5 Wind Classification: Refer to Section 6 for installation requirements to meet wind classifications
TABLE 2A: WIND CLASSIFICATIONS, ASPHALT SHINGLES
Product
FBC Table 1507.2.7.1 or R905.2.6.1
Supreme"
ASTM D3161(F) & ASTM D7158(H)
Berkshire
Duration® Premium
Duration" Premium COOL
TruDefinition° Duration'
TruDefinition" Duration' Designer Color Collection
Oakridge
TruDefinition° Oakridge'
WeatherGuard® HP
5.5.1 Classification by ASTM D7158:
ASTM D7158, Class H applies only to exposure category B or C and a building height of 60 feet or less. Calculations
by a qualified design professional are required for conditions outside these limitations. Contact the shingle
manufacturer for data specific to each shingle.
NEMO ETC, LLC Evaluation Report 037940.02.12-1131
Certificate ofAuthorizotion #32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION F1.10674-1116
Owens Corning Asphalt Roof Shingles Revision 12: 12/11/2020
Page 3 of 10
ONEMOletc.
TABLE 21B: WIND CLASSIFICATIONS, STARTER STRIPS AND HIP & RIDGE
Type
Product
FBC Table 1507.2.7.1 or R905.2.6.1
Starter Strips
Starter Strip Shingle
ASTM D3161, Class F
Starter Strip Plus
SRS TopShield Starter
Hip & Ridge
Shingles
Berkshire' Hip and Ridge Shingles with Sealant
ASTM D3161, Class F
DuraRidge® Hip and Ridge Shingles with Sealant
ProEdge®
WeatherGuard° HP Hip and Ridge Shingles
5.5.2 Refer to Owens Corning published information on wind resistance and installation limitations.
5.6 All components in the roof assembly shall have quality assurance audit in accordance with F.A.C. Rule 61G20-3.
Refer to the Product Approval of the component manufacturer for components that are produced by a Product
Manufacturer other than the report holder on Page 1 of this Evaluation Report.
6.1 GENERAL:
6.1.1 Roof deck, slope, underlayment and fasteners shall comply with FBC 1507.2 / R905.2 and the shingle
manufacturer's minimum requirements.
6.1.2 Underlayment shall be acceptable to the shingle manufacturer and shall hold current Florida Statewide Product
Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3.
6.1.3 Fasteners shall be in accordance with the shingle manufacturer's published requirements, but not less than FBC
1507.2.6 or R905.2.5. Staples are not permitted.
6.1.4 Owens Corning asphalt shingles are acceptable for use in reroof (tear -off) or recover applications, subject to the
limitations set forth in FBC Section 1511 or R908 and published installation instructions.
6.2 ACCESSORY STARTERS:
6.2.1 Installation of Starter Strip Shingle, Starter Strip Plus and SRS TopShield Starter shall comply with the Owens
Corning current published instructions, using minimum five (5) nails per strip.
Felt undedayment Deck
Sell -adhered
Weatherlock'
undedayment
Drip Drip edge
edge
Nails located
2'-3" from eave
Install First Self -searing adhesive
Starter Sir��'pp positioned along eave
shinglevirth
6" reproved Starter Strip shingle overhangs eaves and rakes 'Ii -'/P
Figure 1: Minimum Nailing, Starter Strip
Figure 2: Minimum Nailing, Starter Strip Plus
NEMO ETC, LLC Evaluation Report 037940.02.12-1121
Certificate of Authorization #32455 7TM EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020
Page 4 of 10
ONEMOjetc.
6.2.2 Installation of Starter Shingle Roll shall comply with the Owens Corning current published instructions.
edge
Starter Shingle Roll adhered
directly to underlayment and
primed drip edge
Figure 3: Starter Shingle Roll
6.3 ASPHALTSHINGLES:
6.3.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions, using
minimum four (4) nails per shingle in accordance with FBC 1507.2.7 or R905.2.6, with the following exceptions:
➢ Berkshire shingles require minimum five (5) nails per shingle.
➢ WeatherGuard° HP shingles require minimum six (6) nails per shingle.
Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required
Refer to Owens Corning published information on wind resistance and installation limitations.
6.3.1.1 Supreme:
Normal
Wind Areas
Area para vientos normales
7• (A) �.
�r it
5"Exposure
Exposici6n
Mansard or Area Para
High Wind desvonos y
Areas vientos fuertes
r1- 2• 1B 2• '-
Figure 4: Minimum Nailing, Supreme
(Standard Size)
Normal Mansard or Aran pars
Wind Areas High Vlrind deavanes y
Area paro vientos nonnnlae Areas vientos !banes
trz (A) °•� r�• 2• tEll 2• 1.
. . . . . .. .. I
B 5/8" Exposure
Exposicldn
Figure 5: Minimum Nailing, Supreme
(Metric Size)
NEMO ETC, LLC Evaluation Report 037940.02.12-Rii
Certificate of Authorization #32455 7TH EDITION (20.20) FBC NON-HVHZ EVALUATION F1.10574-1116
Owens Corning Asphalt Roof Shingles Revision 11:12/21/2020
Page 5 of 10
6.3.1.2 Berkshire®:
Sealar" strip
La tha de sellador
8lh" i
9 VT i
9 Yi
Figure 6: S-Nail Pattern, Berkshire
ONEMOjetc.
Sealant strip
La lira de sellador
• �----. t--+ • • + s
�----•"J.--Yj T.
i
Figure 7: 6-Nail Pattern, Berkshire
Sealant strip
La Via de seflador
i" 8 8 t/t' Blip
t"
2" Asphalt roofing cemnt
Cemento de techode astab
Figure 8: Mansard or Steep Slope Pattern, Berkshire
NEMO ETC, LLC Evaluation Report 037940.02.12-R31
Certificate o/Authorizatlon #32455 7'" EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-R16
Owens Corning Asphalt Roof Shingles Revision 11: 12/11/2020
Page 6 of 10
6.3.1.3
ONEMOjetc.
Duration° Premium TruDefinition® Duration Duration® Premium COOL & TruDefinition° Duration' Designer Color
Collection:
4-Nail Fastening Pattern
SureNWIQ fastening area width
Nail, Typical
1" 12" 12" 1"
pens Comirq SveNaJ • p �+07 aW W • Orens Carriip SueNai• •
6-1/8"
6-518"
Figure 9: Standard 4-Nail Pattern, Duration
6-Nall Fastening Pattern
SureNaii® fastening area width
Nall, Typical.
1" 12" 12" 1"
p Camirp Surrl7ai • a+P�J s�+"O • Omn Cainp SveNaS� •
rMir,
r►rd8"
Figure 10: 6-Nail Pattern, Duration
Fastening.for Slopes Greater Than 21:12
SureNaft fastening area width
Nail, Typical
1" 12" 12" 1"
&.— C.—g Sert.0 • ,•L • omm Cornhm sve td •
6-1f8" 5 5f8"
eaposme
�2n
Four 1" Spots of Asphalt Roofing Cement
Figure 11: Mansard or Steep Slope Pattern, Duration
NEW ETC, LLC Evaluation Report 037940.02.12-R11
Certificate of Authorization #32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-Ri6
Owens Corning Asphalt Roof Shingles Revision 11:12/11/2020
Page 7 of 10
6.3.1.4 TruDefinition Oakridge®, Oakridee®:
4 Nail Pattem
Esquema con 4 chrms
K�4
r
--• rc --->I 14-- I'
I 55ffExposure rJails
5518"Exposure I
Expos1d6nde66/8pidg clams EWorid6nde5618PLdg
Figure 12: Standard 4-Nail Pattern, Oakridge
6.3.1.5 WeatherGuard° HP:
6 Nall Pattem
Esquema con 6 claws
661W Exposure
Eapasiddn da 5 618 pu1g.
MEMO I etc.
5 6/8" Exposure '
ExMieffin da 5618pu19
Figure 13: 6-Nail Pattern, Oakridge
Fastening for Slopes Greater Than 21:12
I
SuraNall& fastening area wldih
/ Heg, 7yplcal
�T , F. 92"
Foxy 7" spots orAsp= nooflng Cement
Figure 14: Mansard or Steep -Slope Pattern, Oakridge
6 Nail Pattern
Esquema con 6 davos gall 6 918" from bottom
of shiugls
Clove a 6118 4. ds la
5 5t8" Exposure 6 Fasteners parte inferior a la t4a
Exposicibo de 5 518 pulg. 6 sujetadores
3"
qP4
5f8; asura . 5 5la• E sxa Four V Spots of fthah f3onf Ceram
0 E de55.6put%
iAyo c 6 6�paas Cuetro puntos de cemerlto.de techo de asfalto de f pulgada
Figure 15: 6-Nail Pattern, WeatherGuard HP Figure 16: Mansard or Steep -Slope Pattern, WeatherGuard HP
NEMO ETC, LLC Evaluation Report 037940.02.12-R31
Certiftate oJAuthorizotion N32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 22, 22/21/202D
Page got 1D
ONEMOjetc.
6.4 HIP AND RIDGE SHINGLES: 1
6.4.1 Installation of asphalt shingles shall comply with the Owens Corning current published instructions.
➢ Berkshire' Hip and Ridge Shingles with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant require
minimum two (2) nails per shingle.
➢ WeatherGuard' HP Hip and Ridge Shingles and ProEdge® require minimum four (4) nails per shingle.
Refer to Owens Corning published information on wind resistance and installation limitations.
6.4.1.1 Berkshire® Hip and Ridge with Sealant and DuraRidge® Hip and Ridge Shingles with Sealant:
Fig. A
Prevailing Wind Direction
4 Direcci6n del viento predorninante
Cl
i I
A � y +• r
E>ryowre
Faposid6n de 8 ping
P
Figure 17: Isometric View, Berkshire and DuraRidge
6.4.1.2 WeatherGuard® HP Hip and Ridge Shingles:
Fig. A 4 4
Prevalling vAnd
�— Directbn A
A
balls 4 4
A i I
A I I
TT I i
I I I I
A I I
A I I I I
% ♦
Exposure
Figure 19: Isometric View, WeatherGuard HP Hip and Ridge
Fig. B
Top view
Vista superior
TT
Nail
Clavo
I
Z�g
• Owens Coming SureNaB' •
�
I
I
I�
�Iw
'�
ml 4)IT
I
I
�I
Figure IS: Plan View, Berkshire and DuraRidge
Fig. C Hip & Ridge Shingle Fastening
TopView
Naps Nails
r"
7' 2"
i° 1°
•
g Exposure
I 12'
Figure 20: Plan View, WeatherGuard HP Hip and Ridge
MEMO ETC, LLC Evaluation Report 037940.02.12-1131
Certificate ofAuthorization N32455 7- EDITION (2020) FBC NON-HVHZ EVALUATION FL10674-1116
Owens Corning Asphalt Roof Shingles Revision 31: 12/11/2020
Page 9 of 10
6.4.1.3 ProEdge®:
Prevailing
Wind Direction Sealant Strip
6- Exposure
Fasten 71h
Cover Exposed
Fasteners with
< Roof Cement
Figure 21: Isometric View, ProEdge
ONimojetc.
Standard f—
Fastening
Pattern
i2o Sealant
7 �2 6° Exposure
Figure 22: Plan View, ProEdge
7. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction to properly evaluate the installation of this
product.
Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 QA requirements. Refer
to Section 4 herein for products and production locations having met codified material standards.
9. QUALITY ASSURANCE ENTITY:
PRI Construction Materials Technologies, LLC—QUA9110; JaI31 621-5777; bwilson@Dricmt:Com
NEMO ETC, LLC
t:ertifcate of Authorization #32455
- END OF EVALUATION REPORT -
7- EDITION (2020) FBC NON-HVHZ EVALUATION
Owens Corning Asphalt Roof Shingles
Evaluation Report 037940.02.12-R31
FL10674-1116
Revision 11: 32111/202D
,Page 10 of 10