The URL can be used to link to this page

Home My WebLink AboutEvaluation Report- 9-3-08q(o 3 (08 QOTRRINITYIERD EVALUATION REPORT East Coast Metals, Inc. 2301 West 8 Lane Hialeah, FL 33010 EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization //9503 353 CHRISTIAN STREET, UNIT#13 OXFORD, CT 06478 PHONE: (203) 262-9245 FAX: (203) 262-9243 Evaluation Report E10240.08.08-R4 FL5374-R4 Date of Issuance: 09/03/2008 Revision 4: 03/17/2015 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code'and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code sections noted herein. DESCRIPTION: East Coast Metals Channel Metals LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "TrinitylERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 7. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 03/17/2015. This does not serve as an electronically signed document Signed, sealed hardcopies have been transmitted to the Product Approval Administrator and to the named client CERTIFICATION OF INDEPENDENCE: 1. Trinity IERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinity I ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. S. This is a building code evaluation. Neither Trinity) ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. Ye , Cop_,► \I TRINITY I ERD ROOFING COMPONENT EVALUATION: 1. SCOPE: Product Category: Roofing Sub -Category: Roofing Accessories that are an Integral Part of the Roofing System Compliance Statement: East Coast Metals Channel Metals, as produced by East Coast Metals, have demonstrated compliance with the following sections of the Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: Section Prove Standard Year 1507.3.7 Installation, non-HVHZ FRSA/TRI April 2012 (04-12) 2012 1518.8.1 Installation, HVHZ RAS 118, 119 & 120 1995 1523.6.5.2.2 Static Uplift Resistance TAS 101 1995 1711.2.1 Static Uplift Resistance SBCCI SSTD 11 1997 3. REFERENCES: 9afty Examination Reference Date ERD (TST6049) Static Uplift Resistance E42730.08.13 08/23/2013 ERD (TST6049) Static Uplift Resistance ECM-SC6795.12.14-1 02/27/2015 ERD (TST6049) Static Uplift Resistance ECM-SC6795.12.14-2 02/27/2015 Florida TEC (TST7393) TAS 101 S10-628R 10/27/2010 PRI (TST5878) TAS 101 ECM-001-02-01 09/21/2001 PRI (TST5878) TAS 101 ECM-003-02-01 06/13/2008 PRI (TST5878) TAS 101 ECM-004-02-01 06/13/2008 PRI (TST5878) TAS 101 ECM-005-02-01 06/13/2008 PRI (TST5878) TAS 101 ECM-006-02-01 06/13/2008 PRI (TST5878) TAS 101 ECM-007-02-01 06/13/2008 PRI(TST5878) TAS 101 ECM-008-02-01 06/13/2008 Florida Building Code Attachment Requirements FRSA/TRI April 2012 (04-12) 04/2012 Florida Building Code - HVHZ Attachment Requirements RAS 118,119 and 120 1995 East Coast Metals Metal Quality Mill Certifications Various Architectural Testing (QUA1844) Quality Control Participation Letter Exp.12/31/2018 4. PRODUCT DESCRIPTION: 4.1 Hip & Ridge Channel Metal: Pre -formed metal channel designed for use as a hip and ridge base to which roof tiles are bonded in FBC Approved roof tile adhesive. Hip & Ridge Channel Metal is available in 119-3/8-inch (± 3/8-inch) length by 2.5, 3, 3.5, 4, 5, 6 or 7-inch (± 3/8-inch) heights with 1.5-inch (± 1/16-inch) deck -flanges. Exterior Research and Design, I.I.C. Evaluation Report E10240.08.08-R4 Certificate ojAutharization #9503 FL5374-R4 Revision 4: 03/17/2015 Page 2 of 7 C)O �l I RINITY I ERD 4.2 Trim Lock Channel Metal: Pre -formed metal channel designed for use as a hip and ridge base to which roof tiles are bonded in FBC Approved roof the adhesive. Trim Lock Channel Metal is characterized by its profiled and perforated upper horizontal flange designed to receive and allow for interlock with the overlying tile adhesive. Trim Lock Channel Metal is available in 119-3/8-inch (± 3/8") length by 3, 3.5, 4, 5 or 6-inch L 3/8-inch) heights with 1.5-inch L 1/16-inch) deck -flanges. 4.2 Trim Lock Plus Channel Metal: Pre -formed metal channel designed for use as a hip and ridge base to which roof tiles are bonded in FBC Approved roof tile adhesive. Trim Lock Plus Channel Metal is characterized by its profiled and perforated upper horizontal flange designed to receive and allow for interlock with the overlying tile adhesive and its perforated deck flanges, designed for installation atop the roof underlayment via placement In FBC Approved roof tile adhesive, which flows -through and interlocks with the underlying adhesive. Trim Lock Plus Channel Metal is available in 119-3/8-inch (± 3/8") length by 3, 3.5, 4, 5 or 6-inch (± 3/8-inch) heights with 1.5-inch (± 1/16-inch) deck -flanges., 4.4 East Coast Metals Channel Metals are fabricated of the following metals: ➢ Galvanized Steel: Min. 0.019 ±0.002-inch, ASTM A653 (G-90), min. 33 KSI. ➢ Galvalume Steel: Min. 0.019 ± 0.002-inch, ASTM A792, AZ55, min. 35 KSI. ➢ Aluminum: Min. 0.032±0.002-inch, ASTM B209, 3003-H14, min. 21 KSI. ➢ Stainless Steel: Min. 0.019 ± 0.002-inch, ASTM A240/A480, T304, min. 35 KSI. 5. LIMITATIONS: 5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. Exterior Research and Design, I.I.C. Evaluation Report E10240.08.08-R4 Certifcate ofAuthoriration 09503 FL5374-R4 Revision 4: 03/17/201S Page 3 of 7 rTRINI-rYIERD 5.2 FOR HVHZJURISDICTIONS: 5.2.1 For Hip & Ridge Channel Metal or Trim Lock Channel Metal, refer to FBC RAS 118, Drawing 13, Detail 3; RAS 119, Drawing 12, Detail 3; or RAS 120, Drawing 15, Detail 3. For Trim Lock Plus Channel Metal, refer to the installation instructions herein. 5.2.2 For HVHZ jurisdictions, installations of Hip & Ridge Channel Metal and Trim Lock are prescriptive by RAS 118, 119 and 120, and the data in Tables 1A and 1B is supplemental to these prescriptive allowances. Installations of Trim Lock Plus are limited to projects having a required moment resistance (Mr) or uplift resistance (Fr), as determined in accordance with RAS 127, not greater than the following values. Refer to the tile adhesive manufacturer's published installation instructions for adhesive paddy placement details. ➢ "INDEPENDENT" paddy placement means each individual the is bonded to the Channel Metal in its own, single foam paddy; tile head laps are not bonded. This method is limited to 2-part tile adhesives. Allowable performance data below for "INDEPENDENT" paddy placement already has a 2 to 1 margin of safety applied to ultimate performance. ➢ "INTERDEPENDENT" paddy placement means each individual tile is bonded to the Channel Metal in a foam paddy, and a second foam paddy bonds the the head lap, or two tiles are bonded to the Channel Metal using a single foam paddy. Allowable performance data below for "INTERDEPENDENT" paddy placement already has a 4 to 1 margin of safety applied to ultimate performance. TABLE 1A PERFORMANCE LIMITATIONS r HVHZ, INDEPENDENT PADDYPIACEMENT (2TO1'"GIN OFSAFETYALREADYAPPIJEDf - Hip/Ridge Metal Tile Adhesive Allowable Performance Design Metal Type Type Placement Moment Based Uplift Based Mf (ft-lbf) F' (Ibf) Hip & Ridge galvanized clay or 31VITM" 2-Component Foam Independent 127 169 Channel Metal concrete Roof Tile Adhesive AH-160 Trim Lock galvanized, Galvalume®, clay or 3MTM 2-Component Foam Independent 171 159 aluminum or stainless steel concrete Roof Tile Adhesive AH-160 Trim Lock Plus galvanized, Galvalume®, clay or 3M'" 2-Component Foam Independent 177 165 aluminum or stainless steel concrete Roof Tile Adhesive AH-160 TABLE 1B: PERFORMANCE LIMITATIONS- HVHZ,INTERDEPENDENT PADDY PLACEMENT .. :r. .. . (4TOI MARGINOFSAFElYALREAOYAPPLIEDJ Hip/Ridge Metal Tile Adhesive Allowable Performance Moment Based Uplift Based Design Metal Type Type Placement Mf (ft-lbf) F' (Ibf) Trim Lock or Trim galvanized, Galvalume®, clay or 3MTM 2-Component Foam Interdependent 95 88 Lock Plus aluminum or stainless steel concrete Roof Tile Adhesive AH-160 Trim Lock galvanized, Galvalume®, clay or 3M— Roof Tile Adhesive Interdependent 99 94 stainless steel concrete RTA-1 Trim Lock aluminum clay or 3M— Foam Roof Tile Interdependent 90 84 concrete Adhesive RTA-1 Trim Lock Plus galvanized, Galvalume®, clay or 3M— Foam Roof Tile Interdependent 90 84 aluminum or stainless steel concrete Adhesive RTA-1 Trim Lock galvanized, Galvalume® or clay or TILE BOND— Roof Tile Interdependent 123 117 stainless steel concrete Adhesive Trim Lock aluminum clay or TILE BOND- Roof Tile Interdependent 79 73 concrete Adhesive Trim Lock Plus galvanized, Galvalume®, clay or TILE BOND- Roof Tile Interdependent 79 73 aluminum or stainless steel concrete Adhesive Trim Lock galvanized, Galvalume® or clay or Touch 'n Seal StormBond Interdependent 146 139 stainless steel concrete Roof Tile Adhesive Trim Lock Aluminum clay or Touch'n Seal StormBond Interdependent 58 54 concrete Roof Tile Adhesive Trim Lock Plus galvanized, Galvalume®, clay or Touch'n Seal StormBond Interdependent 58 54 aluminum or stainless steel concrete Roof Tile Adhesive Exterior Research and Design, I.I.C. Evaluation Report E10240.08.08-R4 Certificate of Authorization #9SO3 F1.5374-114 Revision 4: 03/17/2015 Page 4 of 7 TRINITY I ERD 5.3 FOR NON-HVHZJURISDICTIONS: 5.3.1 For Hip & Ridge Channel Metal or Trim Lock Channel Metal, refer to FRSA/TRI April 2012 (04-12). For Trim Lock Plus Channel Metal, refer to the installation instructions herein 5.3.2 For non-HVHZ, installations are limited to projects having hip and ridge design pressure requirements, determined in accordance with Table 1A of FRSA/TRI April 2012 (04-12), not greater than the following values. Refer to the tile adhesive manufacturer's published installation instructions for adhesive paddy placement details. ➢ "INDEPENDENT" paddy placement means each individual tile is bonded to the Channel Metal in its own, single foam paddy; tile head laps are not bonded. This method is limited to 2-part tile adhesives. This method is limited to 2-part tile adhesives. Allowable performance data below for "INDEPENDENT" paddy placement already has a 2 to 1 margin of safety applied to ultimate performance. ➢ "INTERDEPENDENT" paddy placement means each individual tile is bonded to the Channel Metal in a foam paddy, and a second foam paddy bonds the tile head lap, or two tiles are bonded to the Channel Metal using a single foam paddy. Allowable performance data below for "INTERDEPENDENT" paddy placement already has a 4 to 1 margin of safety applied to ultimate performance. TABLE 2A:PERFORMANCE LIMITATIONS=NON-HVHZ, INDEPENDENT PADDY PLACEMENT f2,70I MARGIN OF SAFEiYALRREADYAPPLIED) Hip/Ridge Metal Tile Adhesive Allowable Uplift (Psf) Design Metal Type Type Placement Hip & Ridge galvanized clay or 3M- 2-Component Foam Roof Independent 169 Channel Metal concrete Tile Adhesive AH-160 Trim Lock galvanized, Galvalume®, aluminum or clay or 3M— 2-Component Foam Roof Independent 173 stainless steel concrete Tile Adhesive AH-160 Trim Lock Plus galvanized, Galvalume®, aluminum or clay or 3M- 2-Component Foam Roof Independent 178 stainless steel concrete Tile Adhesive AH-160 TABLE 2B: •PERFORMANCE LIMITATIONS :NON-HVHZ,.INTERDEPEWENT,PADDY PLACEMENT :. (4TOIMARGIN OF3AFE/YA[READYAPPGEO) . Hip/Ridge Metal Tile Adhesive Allowable Uplift (Psf) Design Metal Type Type Placement Trim Lock or Trim galvanized, Galvalume®, aluminum or clay or 31v'TM 2-Component Foam Roof Interdependent 98 Lock Plus stainless steel concrete Tile Adhesive AH-160 Trim Lock galvanized, Galvalume® or stainless clay or 3M- Foam Roof Tile Adhesive Interdependent 110 steel concrete RTA-1 Trim Lock aluminum clay or 3M— Foam Roof Tile Adhesive Interdependent 93 concrete RTA-1 Trim Lock Plus galvanized, Galvalume®, aluminum or clay or 3M" " Foam Roof Tile Adhesive Interdependent 93 stainless steel concrete RTA-1 Trim Lock galvanized, Galvalume® or stainless clay or TILE BOND- Roof Tile Adhesive Interdependent 152 steel concrete Trim Lock aluminum clay or TILE BOND— Roof Tile Adhesive Interdependent 82 concrete Trim Lock Plus galvanized, Galvalume®, aluminum or clay or TILE BOND- Roof Tile Adhesive Interdependent 82 stainless steel concrete Trim Lock galvanized, Galvalume® or stainless clay or Touch 'n Seal StormBond Roof Interdependent 148 steel concrete Tile Adhesive Trim Lock Aluminum clay or Touch 'n Seal StormBond Roof Interdependent 61 concrete Tile Adhesive Trim Lock Plus galvanized, Galvalume®, aluminum or clay or Touch 'n Seal StormBond Roof Interdependent 61 stainless steel I concrete Tile Adhesive Exterior Research and Design, I.I.C. Evaluation Report E10240.08.08-R4 Certificate afAuthorization #95D3 FL5374-R4 Revision 4: 03/17/2015 Page 5 of 7 QOTRINITYIERD 6. INSTALLATION: 6.1 The roof deck shall be minimum 15/32-inch plywood (non-HVHZ) or minimum 19/32-inch plywood (HVHZ) attached in accordance with FBC Chapter 23 to the satisfaction of the AHJ. 6.2 Hip & Ridge Channel Metal and Trim Lock Channel Metal shall be installed using min. 11 ga. x 1%-inch long x 3/8-inch head diameter galvanized annular ring shank nails spaced 6-inch o.c. along both deck -flanges. Fasteners shall be positioned Y44-inch from the outside edge of each deck -flange, set in a bed plastic roof cement. For FBC HVHZ, refer to FBC RAS 118, Drawing 13, Detail 3; RAS 119, Drawing 12, Detail 3; or RAS 120, Drawing 15, Detail 3. 6.3 Trim Lock Plus Channel Metal shall be installed atop the Approved roof underlayment in continuous 2-inch wide ribbons of tile adhesive centered beneath each 1.5-inch wide deck flange. Place the Trim Lock Plus Channel Metal into the wet adhesive and allow it to set-up prior to installation of roof tiles. View of Polyset AH160 Placement for Trim Lock Plus Channel Metal Installation 6.3.1 It is critical that the bond between the Trim Lock Plus Channel Metal, the tile adhesive and the underlayment is not disturbed prior to or during placement of the ridge tiles. 6.3.2 Approved underlayments are the codified '30/90' system or other FBC Approved roof underlayments listing approved use of the subject tile adhesive. Exterior Research and Design, I.I.C. Evaluation Report E10240.08.08-R4 Certificate ojAuthorization #9503 FL5374-R4 Revision 4: 03/17/2015 Page 6 of 7 ►A 8. 9. I RINITi I ERD 6.4 Tile shall be installed atop the Channel Metal in accordance with the tile adhesive manufacturer's Approved, published installation instructions, subject to the limitations outlined in Section 5 herein. The exposed edges shall be packed and pointed with Approved mortar or weather blocking adhesive in accordance with FRSA/TRI April 2012 (04-12) or RAS 118, RAS 119, RAS 120 requirements. Hip / Ridge Tile Tile Adhesive Trim Lock Plus • ':''' '• ''-''• Mortar or Weather Block Adhesive .s w '.r •r•.j. Tile Adhesive �••.-,. is f•,'. ,�,f.a. View of Trim Lock Plus Channel Metal Installation after Weather Blocked 6.4.1 Channel Metal shall be free of dust, debris, oils or other bond -breaking substance prior to placement of adhesive. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. MANUFACTURING PLANTS: Contact the named QA entity for manufacturing facilities covered by F.A.C. Rule 61G20-3 CIA requirements. QUALITY ASSURANCE ENTITY: Architectural Testing, Inc. — QUA1844; (717) 764-7700 - END OF EVALUATION REPORT - Exterior Research and Design, U.C. Evaluation Report E10240.08.08-R4 Certificate of Authorization #9503 FL5374-R4 Revision 4: 03/17/2015 Page 7 of 7