HomeMy WebLinkAboutAPPROVED, 195 Tumblin Kling Permit InfoST. LUCIE WORKS
ST LUCIE COUNTY ROOFING PERMIT INFORMATION SHEET
Florida Building Code 7th Edition (2020)
Based on Section 1525 of the Florida Building Code - Building
INSTRUCTION PAGE
COMPLETE THE NECESSARY SECTIONS OF THE UNIFORM ROOFING SHEET
APPLICATION FORM AND ATTACH THE REQUIRED DOCUMENTS AS NOTED
BELOW:
Roof System
Required Sections of
the Permit Application
Form
Attachments Required
See List Below
Low Slope Application
A B C
1,2,3,4,5,6,7
Prescriptive BUR-RAS 150
A, 8, C
2,4,5,6,7
Asphaltic Shingles
A, 8, D
1,2,4,5,6,7
Concrete or Clay Tile
A, B, D, E
1,2,3,4,5,6,7
Metal Roofs
A, B, D
1,2,3,4,5,6.7
Wood Shingles and
Shakes
Other
A, B, D
As Applicable
1,2,4,5,6,7
— j
1 2 3 4 5 6 7
ATTACHMENTS REQUIRED As Applicable):
1.
Fire Directory Listing Page
2.
From Product Approval:
Front Page
Specific System Description
Specific System Limitations
General Limitations
Applicable Detail Drawings
3.
Design Calculations per Chapter 16, or if applicable, RAS 127 or RAS 128
4.
Other Component of Product Approval
5,
Municipal Permit Application
6.
Owners Notification for Roofing Considerations (Reroofing Only)
7,
Any Required Roof Testing/Calculation Documentation
Form RooflnfoFeb21 Rev Feb 18, 2021
ST. LUCIE WORKS
Section A (General Information)
Master Permit No.
Contractors Name: Collins Roofing Inc.
Process No.
License # CCC-058011
ROOF CATEGORY
❑ Low Slope ❑ fyechanically Fastened Tile ❑ Mortar/Adhesive Set Tiles
❑ Asphaltic Shingles etalPanel/Shingles ❑Wood Shingles/Shakes
❑ Prescriptive BUR-RAS 150
ROOF ROOF TYPE. ,
❑ New roof ❑ Repair ❑ Maintenance Reroofing ❑Recovering
ROOF SYSTEM INFORMATION
Low Slope Roof Area (SF)t0- 4 Steep Sloped Roof Area (SF) _
—> Total (SF)
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
3'
If
ST. LUCIE WORKS
Section D (Steep Slope Roof System)
Extreme Metal Fab
Roof System Manufacturer:
Notice of Acceptance Number: FL 17023
Minimum Design Wind Pressures, If Apeliic�
cable (From RAS 127 or Calculation
s): $.1 7
— Zone 1:?-Zone 2eL� l Zone 2n:SZone 2rrC� one 3e:—Zone 3r:
Deck Type: 5/8" Plywood
Type Underlayment High Temp/Self Adhesive Underlayment M t Y
Roof Slope:
12 Insulation: N/A
Fire Barrier: N/A
Ridge Ventilation? Fastener Type & Spacing: #10x1.5'-12"x12" Pattern 16" D.C. (Wood Zac)
N/A
Adhesive Type: N/A
Type Cap Sheet N/A
Mean Roof Height: 15ft Roof Covering: 26 Ga 5V Metal Roof Panels
III Type & Size Drip 2"x2" Galv. Steel
Edge:
ST. LUCIE VVORKS
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(If a component is not used, identify as "NA")
System Manufacturer:
Product Approval No.:
Design Wind Pressures, From RAS 128 Or Calculations:
Zone 1': Zone 1: _ Zone 2: _Zone 3: _
Max. Design Pressure, from the specific product approval
system:
Deck:
Type:
Gauge Thickness:
Slope:
Anchor/Base Sheet & No. df Ply(s):
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheet(s) & No. of Ply(s):
Base Sheet Fastener/Bonding Material:
Ply Sheet(s)' & No. of Ply(s):
Ply Sheet Fastener/Bonding Material:
Top Ply:
Top Ply Fastener/Bonding Material:
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':—"
oc @ Lap, # Rows_
@ _" oc
Zone 1:—"
oc @ Lap, # Rows
— @ —" oc
Zone 2:_"
oc @ Lap, # Rows
— @ —" oc
Zone 3:_"
oc @ Lap, # Rows_
@ —" oc
Number of Fasteners Per Insulation Board:
Zone 1': Zone 1:—Zone 2:—Zone 3:,
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc.
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16.