HomeMy WebLinkAboutGeneral Specificationsauar.Rirs>rEet
Quality Steel Corporation AG/UG Propane Tanks
LEG WIDTH
1450 wg. AND UP
APPROXIMATE ABOVEGROUND/UNDEGROUND 1AG/UG1 VESSEL DIMENSIONS AND SPECIFICATIONS
WATER
CAPACITY
DIAMETER
(OD)
HEAD
TYPE
OVERALL
LENGTH
OVERALL
HEIGHT
LEG*
WIDTH
LEG**
SPACING
WEIGHT
(Ibs.)
**QUANTITY
FULL LOAD
PER STACK
*120 wg.
24"
Ellip.
5'-8"
3'
1'-1 1/2"
2'-10 1/2"
260
108 196
16112
*250 wg.
30"
Hemi.
7'-10"
3'-8"
1'-5"
1 4'-11"
480
54
9
*320 wg.
1 30"
Hemi.
9'-7"
3'-8"
1'-5"
5'
620
45
9
500 wg.
1 37 1/2"
Hemi.
10,
4'-2"
1'-8"
5'
950
37 130
8 1 6
1000 wg.
41"
Hemi.
16'
4'-5"
1'-8"
11'-9 1/2"
1,800
17 1 15
6 15
1450 wg.
461/2"
Ellip.
17'-4"
4'-11"
1'-9"
11'-7"
1 2,650
1 12
4
1990 wg.
461/2"
Ellip.
23'-11"
4'-11"
1'-9"
16'
1 3,520
1 8
1 4
Dimensions and specifications shown are approximate. Individual vessels may vary.
* Leg spacing+/- 2". Leg widths and spacing may vary based on mfg. location. Check with your salesperson for details. 120, 250, 320 wg. standard tanks
- no holes in legs (one center hole on request). 500 and 1000 wg. standard tanks - 2 holes 16" on center. 1450 wg. and up as shown above.
** Full load and stack quantities vary by shipping location. Check with your salesperson for details.
General Specifications
- Conforms to the latest edition of ASME Rules for Construction of Pressure Vessels, Section Vill, Division 1.
Complies with NFPA 58.
- Rated at 250 psig from -20' F to 125' F. All vessels registered with National Board.
- Two service options available:
Option 1: Ready -to -bury underground option, coated with either powder coated phenolic epoxy finish
or liquid applied epoxy primer coat followed by urethane top coat, supplied with composite
AG/UG dome.
Option 2: Aboveground option, coated with either powder coated TGIC polyester finish or liquid
applied epoxy primer coat followed by urethane topcoat, supplied with steel AG/UG dome.
- All vessels are shipped vacuum pre -purged to enable simplified first fill of the vessel.
Updated January 14, 2015
PROPANE CONSTRUCTION NOTES
1.
All pipe and fittings above ground and inside building shall be
SCH. 40 Galvanized ASTM A120 or AGA approved. corrugated
stainless steel (C.S.S.T.) pipe.
2.
All polypipe and fittings shall be ASTM D2513 or ASTM D2517
and shall be buried outside underground at a depth of 18" with
warning tape and tracer wire.
3.
All pipe and meter locations are approximate and subject to
change.
4:
All- polypipe shall be joined by heat fusion or approved mechanical
couplings. ,
5.
All 'g.alvanized pipe shall be threaded.
6.
All pipe shall be pressure.tested to 20 # PSI for a 24
period of
hours.
SO
WIL
I Ell
Tl
Z72"�
o PL a —.�•
�fa�f�.—if
f ' sir 1-9
�. •
I UNDERGROUND TANK INSTALLATIOR
2" 6o G'
DOWNGRADED AWAY '
•
FROM DOME
'=y
•MIN. e"'tt ,i • �'
t ANODE CABLE
SACRIFICIAL ANODE ��� %?` • • . • •�
.
•
(MAGNESIUM BAG) • +
,•
• vs 4 • *��
q%'n!' I
REGULATOR
rA1,
..
SHUT GAS OFF AT
• OUTSIDE YALYE
IR ABOVE ADE
.....
RISER 0
i
•
WARY IlG TAPE •
�
Y
. •..
•
_ . ' RrsER�
GRADE/CONCRETE
1
.
SLEEVE
•
Nt
as
UHOEAGnOU110
V,0AS COHUUHEn SERVICE LINE
jF;l
'
TRACE HIRE
1