HomeMy WebLinkAboutGENERAL INFORMATION SECTION ASection A (General Information)
Master Permit No.
Process No.
Contractors Name: 1�.� ���,�Lifense #
r
Job Address �� � �► �- C - - -\�-c
0 Low Slope
❑ Asphaltic Shingles
❑ New roof ❑ Repair
Low Slope Roof Area (SF) 3 \C
ROOF CATEGORY
❑ Mechanically Fastened Tile ❑ Mortar/Adhesive Set Tiles
Metal Panel/Shingles ❑Wood Shingles/Shakes
❑ Prescriptive BUR-RAS 150
ROOF RO.OF.TYPE.
❑ Maintenance Reroofing
ROOF SYSTEM INFORMATION
Steep Sloped Roof Area (SF) _ j �0
❑ Recovering
Total (SF) 3 a E9 o
Section B (Roof Plan)
Sketch Roof Plan: Illustrate all levels and sections, roof drains, scuppers, overflow scuppers and overflow drains.
Include dimensions of sections and levels, clearly identify dimensions of elevated pressure zones and location of parapets.
Section C (Low Slope Roof)
Fill in specific roof assembly components and identify
manufacturer
(If a component is not us d, 'd ntify a NA")
System Manufacturer: ,/T4— ,ai (\C
Product Approval No.:E
Design Wind Pressures, From RAS 128 Or Calculations:
6
Zone V. 1 X 4 one 1: Zone 2:4* one 3"�
Max. Design Pressure fry the specific product approval
system: 7 t
Deck:
Type:
Gauge Thickness:
(�a
Slope: I / ��_-
Anchor/Base Sheet & No. df Ply(s):
Anchor/Base Sheet Fastener/Bonding Material:
Insulation Base Layer:
Base Insultation Size and Thickness:
Base Insulation Fastener/Bonding Material:
Top Insulation Layer:
Top Insulation Size and Thickness:
Top Insulation Fastener/Bonding Material:
Base Sheet(s) & No. of Ply(s):
Surfacing:
Fastener Spacing for Anchor/Base Sheet Attachment:
Zone 1':—" oc @ Lap, # Rows— ®" oc
Zone 1:—" oc @ Lap, # Rows — @ oc
Zone 2:_._." oc @ Lap, # Rows — ®�" oc
Zone 3:—" oc @ Lap, # Rows @ �" oc
Number of Fasteners Per Insulation Board:
Zone 1': Zone 1: Zone 2: Zone 3
Illustrate Components Noted and Details as Applicable:
Woodblocking, Gutter, Edge Termination, Stripping,
' Flashing, Continuous Cleat, Cant Strip, Base Flashing,
Counterflashing, Coping, Etc.,
Indicate: Mean Roof Height, Parapet Height, Height of Base
Flashing, Component Material, Material' Thickness, Fastener
Type, Fastener Spacing or Submit Manufacturers Details that
Comply with RAS 111 and Chapter 16..
Base Sheet sten r/Bondin Mate iai.
Ply Sheet(s)' & No. of Ply(s): wI �( P
Ply Sheet Fastener/Bonding Material:
Top Ply:
Top Ply Fastener/Bonding Material:
�� A�- E
Section D (Steep Slope Roof System)
Roof System Manufacturer: k±11qA'
Notice of Acceptance Number: r- L n � 2,
Minimum Design Wind Pressures, If Applicable (From RAS 127 or Calculations):
Zone 1: d L• Lone 2e::�"one 2n: Zone 2r: Zone 3e: J Z Zone 3r:
Deck Type: I f C'� Lj pv �_-
Type Underlayment:
Roof Slope.
.1 2 --
Insulation:
Fire Barrier:
Ridge Ventilation? Fastener Type &Spacing: i�fo� Z. i12—
3
Adhesive Type:
Type Gap Sheet:
Mean Roof Height: _!' Roof Covering:11z6
Type & Size Drip
Edge: