The URL can be used to link to this page

Home My WebLink AboutNOA polyglass 2022 NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 1 of 63 MIAMI-DADE COUNTY PRODUCT CONTROL SECTION DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208 BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474 T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy Polyglass USA, Inc. 1111 W. Newport Center Drive Deerfield Beach, FL 33442 SCOPE: This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER - Product Control Section to be used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ). This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements of the applicable building code. This product is approved as described herein, and has been designed to comply with the Florida Building Code including the High Velocity Hurricane Zone of the Florida Building Code. DESCRIPTION: Polyglass Modified Bitumen Roof System Over Wood Decks LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following statement: "Miami-Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA renews NOA#15-0928.05 and consists of pages 1 through 63. The submitted documentation was reviewed by Alex Tigera. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 2 of 63 ROOFING ASSEMBLY APPROVAL Category: Roofing Sub-Category: Modified Bitumen Materials SBS/APP Deck Type: Wood Maximum Design Pressure -120 psf TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Dimensions Test Specification Product Description Polyglass G2 Base 108’ x 36” ASTM D 4601 Type II Asphalt-coated fiberglass reinforced base sheet Polyflex SA Base 66’ 8” x 3’ 3-3/8” ASTM D 4601 Type II Self-adhered, fiberglass reinforced, APP modified bitumen base sheet. Elastobase 65’ 8” x 3’ 3-3/8” ASTM D 6163 SBS modified asphalt coated fiberglass reinforced base sheet. Elastoflex SA V 66’ 8” x 3’ 3-3/8” ASTM D 6163, Type I Self-adhered, fiberglass reinforced, SBS modified bitumen membrane with a self-adhering back face and a smooth top surface. Elastoflex SA V FR 66’ 8” x 3’ 3-3/8” ASTM D 6163 Self-adhered, fire-rated, fiberglass reinforced, SBS modified bitumen membrane with a self-adhering back face and a smooth top surface. Elastoflex SA V PLUS 66’ 8” x 3’ 3-3/8” ASTM D 6163 Self-adhered, fiberglass reinforced, SBS modified bitumen membrane with a self-adhering back face and a smooth top surface. Elastoflex SA V PLUS FR 66’ 8” x 3’ 3-3/8” ASTM D 6163 Self-adhered, fiberglass reinforced, SBS modified bitumen membrane with a a fire retardant additive, self-adhering back face and a smooth top surface. Elastoflex V 32’ 10” x 3’ 3-3/8” ASTM D 6163 Torch, hot asphalt or cold adhesive applied, fiberglass reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a sanded top surface. Also available in a thicker version listed as Elastoflex V 2.5. Elastoflex VG 32’ 10” x 3’ 3-3/8” ASTM D 6163 Torch, hot asphalt or cold adhesive applied, fiberglass reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. Elastoflex VG FR 32’ 10” x 3’ 3-3/8” ASTM D 6163 Torch, hot asphalt or cold adhesive applied, fire-rated, fiberglass reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. Polyglass HT Base 650 65’ 8” x 3’ 3-3/8” ASTM D 6163 SBS modified asphalt coated fiberglass reinforced base sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 3 of 63 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Dimensions Test Specification Product Description XtraFlex SBS Base SA 66’ 8” x 3’ 3-3/8” ASTM D 6163 Self-adhered, fiberglass reinforced, SBS modified bitumen membrane with a self-adhering back face and a smooth top surface. XtraFlex SBS Glass Base 65’ 8” x 3’ 3-3/8” ASTM D 6163 SBS modified asphalt coated fiberglass reinforced base sheet. XtraFlex SBS Glass Interply 32’ 10” x 3’ 3-3/8” ASTM D 6163 Torch, hot asphalt or cold adhesive applied, fiberglass reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a sanded top surface. XtraFlex SBS HT Base 650 65’ 8” x 3’ 3-3/8” ASTM D 6163 SBS modified asphalt coated fiberglass reinforced base sheet. Elastobase P 65’ 8” x 3’ 3-3/8” ASTM D 6164 SBS modified asphalt coated polyester reinforced base sheet. Elastoflex S6 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a polyethylene or sanded top surface. Elastoflex S6 G 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. Elastoflex S6 G FR 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, fire-rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. Elastoshield TSG 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. Elastoshield TSG FR 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, fire-rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. Polyfresko G SBS 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface. Polyfresko G SBS FR 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, fire-rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 4 of 63 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Dimensions Test Specification Product Description XtraFlex SBS Poly Base 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a polyethylene or sanded top surface. XtraFlex SBS Poly G 32’ 10” x 3’ 3-3/8” ASTM D 6164 Torch, hot asphalt or cold adhesive applied, fire-rated, polyester reinforced, SBS modified bitumen membrane with a burn off polyethylene or sanded back face and a granule top surface and fire retardant chemistry. Polybond 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Polybond G 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. Polyflex 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. Polyflex G 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. Polyflex G FR 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, fire-rated, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface and fire retardant chemistry. Polyfresko G 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. Polyfresko G FR 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, fire-rated, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface and fire retardant chemistry. XtraFlex APP G 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, fire-rated, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface and fire retardant chemistry. XtraFlex APP S 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a smooth or sanded top surface. XtraFlex Kool APP G 32’ 10” x 3’ 3-3/8” ASTM D 6222 Torch applied, polyester reinforced, APP modified bitumen membrane with a burn off polyethylene back face and a granule top surface. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 5 of 63 TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT: TABLE 1 Product Dimensions Test Specification Product Description Polyglass APP Base 65’ 8” x 3’ 3-3/8” ASTM D 6509 Type I APP modified asphalt coated fiberglass reinforced base sheet. PG 100 Asphalt Primer 1, 3, 5, 50, 55 gal, tube or 17 oz. spray can ASTM D41 A penetrating solution of solvent and a blend of selected asphalts used to promote adhesion. XtraFlex 10 Asphalt Primer 1, 3, 5, 50, 55 gal, tube or 17 oz. spray can ASTM D41 A penetrating solution of solvent and a blend of selected asphalts used to promote adhesion. PG 325 Cold Process Adhesive 1, 3, 5, 50, 55 gal. or tube ASTM D3019 Type III A fibered cold process adhesive for use with roll or BUR roofing. PG 350 Mod Bit Adhesive 1, 3, 5, 50, 55 gal. or tube ASTM D3019 Type III A fibered rubberized adhesive designed for use with modified bitumen membranes. Polyplus 35 Premium Mod Bit Adhesive 1, 3, 5, 50, 55 gal. or tube ASTM D3019 Type III A fibered rubberized adhesive designed for use with modified bitumen membranes. PG 450 Flashing Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 A thick, fibered, rubberized flashing cement. PG 500 MB Flashing Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 A thick, fibered, rubberized flashing cement for use with modified bitumen membranes. Polyplus 45 Premium Flashing Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 A thick, fibered, rubberized flashing cement. Polyplus 50 Premium MB Flashing Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 A thick, fibered, rubberized flashing cement for use with modified bitumen membranes. Polyplus 55 Premium Modified Flashing Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 A mastic compound for use as a roof flashing adhesive. XtraFlex 50 Premium Modified Wet/Dry Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 A thick, fibered, rubberized flashing cement for use with modified bitumen membranes. PG 400 Plastic Roof Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 ASTM D3409 A thick, fibered, rubberized flashing cement for use in dry or damp conditions. PG 425 Wet/Dry Plastic Roof Cement 1, 3, 5, 50, 55 gal. or tube ASTM D4586 ASTM D3409 A thick, fibered, rubberized flashing cement for use in dry or damp conditions. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 6 of 63 APPROVED INSULATIONS: TABLE 2 Product Name Product Description Manufacturer (With Current NOA) Polytherm Polyisocyanurate foam insulation Polyglass USA, Inc. Polytherm-H Polyisocyanurate foam insulation Polyglass USA, Inc. ACFoam-II, ACFoam-III Polyisocyanurate foam insulation Atlas Roofing Corporation DensDeck, DensDeck Prime Gypsum insulation board Georgia Pacific Gypsum LLC FescoBoard Rigid perlite roof insulation board. Johns Manville Corp. H-Shield Polyisocyanurate foam insulation Hunter Panels, LLC H-Shield-CG Polyisocyanurate/perlite composite insulation Hunter Panels, LLC ENRGY 3 Polyisocyanurate foam insulation Johns Manville Corp. Multi-Max FA-3 Polyisocyanurate foam insulation Rmax Operating, LLC SECUROCK Gypsum-Fiber Board Fiber reinforced coverboard USG Corporation EnergyGuard Polyiso Insulation Polyisocyanurate foam insulation GAF ISO 95+ GL Polyisocyanurate foam insulation Firestone Building Products Company, LLC Structodek High Density Fiberboard Roof Insulation Wood fiber board Blue Ridge Fiberboard, Inc. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 7 of 63 APPROVED FASTENERS/ADHESIVES: TABLE 3 Fastener Number Product Name Product Description Dimensions Manufacturer (With Current NOA) 1. Polygrip Fastener #12, #14 & #15 Insulation fastener for wood, steel and concrete decks Various Polyglass USA, Inc. 2. Polygrip Hex Plate Galvalume hex stress plate. 2 7/8" x 3 1/4" Polyglass USA, Inc. 3. Dekfast 12, Dekfast 14 & Dekfast 15 HS Insulation fastener for wood, steel and concrete decks Various SFS Intec, Inc. 4. Dekfast Galvalume Steel Hex Plate Galvalume hex stress plate. 2 7/8" x 3 ¼” SFS Intec, Inc. 5. #12 Standard Roofgrip & #14 Roofgrip Insulation and membrane fastener Various OMG, Inc. 6. Flat Bottom Metal Plate Galvalume AZ50 stress plate 3" square OMG, Inc. 7. Trufast #14 HD Fastener Insulation fastener for steel and wood decks Various Altenloh, Brinck & Co. U.S., Inc. 8. Trufast 3” Metal Insulation Plate Galvalume steel plate 3" round Altenloh, Brinck & Co. U.S., Inc. 9. 3 in. Round Metal Plate Galvalume stress plate. 3” round OMG, Inc. 10. OMG Heavy Duty Truss head, self-drilling, pinch point fastener Various OMG, Inc. 11. Trufast #12 DP Fastener Carbon steel screw with #3 phillips drive Various Altenloh, Brinck & Co. U.S., Inc. 12. OMG 3” Galvalume Steel Plate Galvalume coated steel plate 3” round OMG, Inc. 13. AccuTrac Flat Bottom Aluminized steel plate 3” square OMG, Inc. 14. Simplex MAXX Cap Fasteners Polymer stress plate with two ring shank nails 3” round x 1” long Simplex Nails. Inc. 15. ICP Adhesives CR-20 A two component elastomeric polyurethane foam adhesive ICP Adhesives and Sealants, Inc. 16. Insta Stick Quik Set Insulation Adhesive A single component urethane foam adhesive The Dow Chemical Co. 17. Millennium One Step Foamable Insulation Adhesive A two component, low rise, polyurethane foam adhesive Adco Products, Inc. dba Royal Adhesives & Sealants 18. OlyBond 500 A two component polyurethane foam adhesive OMG, Inc. 19. OlyBond 500 Green A two component, low rise, polyurethane foam adhesive OMG, Inc. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 8 of 63 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer’s application instructions. Number Product Name Product Description Application Rate Specification Manufacturer 1. Gravel To be installed in a flood coat of approved asphalt at 60 lbs/sq 400 lbs/sq N/A Generic 2. Slag To be installed in a flood coat of approved asphalt at 60 lbs/sq 300 lbs/sq N/A Generic 3. KM Acryl 15 A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 KM Coatings Manufacturing 4. KM Acryl 15 QS A premium white quick setting, elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 KM Coatings Manufacturing 5. KM Acryl 25 A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 KM Coatings Manufacturing 6. KM Acryl 25 QS A premium white quick setting, elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 KM Coatings Manufacturing 7. PS #220 A single component, solvent, moisture cure silicone coating. 1.25 gal/sq ASTM D6694 KM Coatings Manufacturing 8. PS #250 A premium grade high solids, single component, moisture cure, fluid applied silicone coating 1.25 gal/sq ASTM D6694 KM Coatings Manufacturing 9. PG 200 Non-Fibered Roof Coating A non fibered asphaltic coating used to add life and rejuvenate existing BUR roofing substrates. 1½-2 gal/sq TAS 140 Polyglass USA, Inc NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 9 of 63 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer’s application instructions. Number Product Name Product Description Application Rate Specification Manufacturer 10. PG 300 Fibered Roof Coating An asphalt cutback fibered roof coating. May be applied by brush or spray equipment to rejuvenate aged BUR 1½-2 gal/sq ASTM D4479 Polyglass USA, Inc. 11. PG 600 Non-Fibered Aluminum Roof Coating Non-fibered aluminum roof coating. ½-1 gal/sq ASTM D2824 Type I Polyglass USA, Inc. 12. PG 650 Fibered Aluminum Roof Coating Fibered aluminum roof coating. 1½-2 gal/sq ASTM D2824 Type III Polyglass USA, Inc. 13. PG 700 Elastomeric Roof Coating A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 Polyglass USA, Inc. 14. PG 700 QS Elastomeric Roof Coating A premium white quick setting, elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 Polyglass USA, Inc. 15. PG 800 Non-Fibered Asphalt Emulsion Roof Coating An asphalt based, non-fibered clay emulsion 3 gal/sq in two coats ASTM D1227 Polyglass USA, Inc. 16. Polybrite 70 Premium Grade Elastomeric Roof Coating A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 Polyglass USA, Inc. 17. Polybrite 70 QS Premium Grade Elastomeric Roof Coating A premium white quick setting, elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 Polyglass USA, Inc. 18. Polybrite 90 High Solids Silicone Roof Coating A premium grade high solids, single component, moisture cure, fluid applied silicone coating 1.25 gal/sq ASTM D6694 Polyglass USA, Inc. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 10 of 63 APPROVED SURFACING: TABLE 4 Chosen components must be applied according to manufacturer’s application instructions. Number Product Name Product Description Application Rate Specification Manufacturer 19. Polybrite 95 Silicone Roof Coating A single component, solvent, moisture cure silicone coating. 1.25 gal/sq ASTM D6694 Polyglass USA, Inc. 20. Polyplus 60 Premium Non-Fibered Aluminum Roof Coating Non-fibered aluminum roof coating. ½-1 gal/sq ASTM D2824 Type I Polyglass USA, Inc. 21. Polyplus 65 Premium Fibered Aluminum Roof Coating Fibered aluminum roof coating. 1½-2 gal/sq ASTM D2824 Type III Polyglass USA, Inc. 22. XtraFlex 20 Bituminous Roof Coating A non fibered asphaltic coating used to add life and rejuvenate existing BUR roofing substrates. 1½-2 gal/sq TAS 140 Polyglass USA, Inc 23. XtraFlex 60 Aluminum Roof Coating Non-fibered aluminum roof coating. ½-1 gal/sq ASTM D2824 Type I Polyglass USA, Inc. 24. XtraFlex 65 Aluminum Roof Coating Fibered Fibered aluminum roof coating. 1½-2 gal/sq ASTM D2824 Type III Polyglass USA, Inc. 25. XtraFlex 70 Premium Acrylic FR Roof Coating A premium white elastomeric acrylic based roof coating (water-based). A polyester fabric may be used for reinforcement with this coating. 1-1½ gal/sq ASTM D6083 Polyglass USA, Inc. 26. XtraFlex 80 Emulsion Roof Coating An asphalt based, non-fibered clay emulsion 3 gal/sq in two coats ASTM D1227 Polyglass USA, Inc. 27. XtraFlex Bituminous Roof Coating Fibered An asphalt cutback fibered roof coating. May be applied by brush or spray equipment to rejuvenate aged BUR 1½-2 gal/sq ASTM D4479 Polyglass USA, Inc. 28. XtraFlex SRC 8000 Silicone Roof Coating A single component, solvent, moisture cure silicone coating. 1.25 gal/sq ASTM D6694 Polyglass USA, Inc. 29. XtraFlex SRC 9600 High Solids Silicone Roof Coating A premium grade high solids, single component, moisture cure, fluid applied silicone coating 1.25 gal/sq ASTM D6694 Polyglass USA, Inc. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 11 of 63 EVIDENCE SUBMITTED: Test Agency Test Name/Report Report No. Date Factory Mutual Research 4470 2W7A7.AM 08.04.94 Corporation 4470 3000857 01.12.00 4470 3004091 01.12.00 4470 3001334 02.15.00 4470 3031350 09.27.07 4470 RR202591 10.22.15 Underwriters Laboratory TAS 114 00NK20869 06.08.00 UL 790 R14571 06.30.15 Trinity | ERD TAS 114 11751.05.03 05.30.03 TAS 114 11758.08.03 08.11.03 TAS 114 P1738.02.07 02.05.07 TAS 117(B)-ASTM D6862 C8500SC.11.07 11.30.07 ASTM D 6164 / D 6222 P10490.10.08-R1 10.03.08 TAS 114 P13760.09.09 09.10.09 ASTM D6163 / ASTM D 4601 P33960.03.11 03.15.11 FM 4470 & TAS 114 P33970.03.11 03.15.11 TAS 117 (B) & TAS 114 P39680.03.13 03.04.13 ASTM D6164 P37590.03.13-3A 03.06.13 TAS 114 11757.12.00-1-R1 04.29.13 TAS 114 11757.04.01-1-R1 04.30.13 ASTM D6509 P37590.03.13-1-R1 06.26.13 ASTM D6222 P37590.07.13-2 07.01.13 ASTM D6222 P37590.03.13-5-R1 07.01.13 ASTM D6163 P37590.03.13-2-R1 07.01.13 ASTM D6164 P37590.07.13-1 07.02.13 TAS 114 & FM 4474 P41630.08.13 08.06.13 ASTM D4601 / TAS 117 P45940.09.13 09.04.13 ASTM D4601 P44370.10.13 10/04/13 ASTM D6162 SC5170.05.15 05.08.15 ASTM D6162 SC5170.12.15-1 12/29/15 ASTM D6163 PLYG-P45440SC.03.15-2-R1 12.29.15 ASTM D6163 PLYG-P45440SC.03.15-1-R1 02.19.16 TAS 114 & FM 4474 PLYG-SC8905.05.16-1 05.17.16 TAS 114 & FM 4474 PLYG-SC8905.05.16-2 05.17.16 TAS 114 P1734.07.06-R2 08.24.16 PRI Asphalt Technologies ASTM D6222 PUSA-062-02-01 12.04.07 ASTM D6163 PUSA-064-02-02 02.27.08 ASTM D6694 PUSA-134-02-01 05.16.14 ASTM D6694 PUSA-135-02-01 05.16.14 NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 12 of 63 APPROVED ASSEMBLIES Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type A(1): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is subsequently adhered to insulation All General and System Limitations apply. One or more layers of the following: Anchor Sheet: One ply of Polyglass APP Base or Polyglass G2 Base fastened to the deck as described below: Fastening #1: Attach base sheet using 11 ga. annular ring shank and 1-5/8” diameter tin caps spaced 8” o.c. in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet. Fastening #2: Attach base sheet using OMG Roofgrip Fasteners with Flat Bottom Metal Plates, Dekfast 14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners #14 with Polygrip Hex Plates or Trufast #14 HD Fasteners with Trufast 3” Metal Insulation Plates spaced 12” o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet. Base Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 ENRGY 3, ISO 95+ GL, ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, Multi-Max FA-3 Minimum 1.5” thick N/A N/A Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 FescoBoard Minimum ¾” thick N/A N/A Structodek High Density Fiberboard Roof Insulation Minimum ½” thick N/A N/A DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 13 of 63 Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Base/Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered to DensDeck Prime or SECUROCK Gypsum-Fiber Board. *Requires torch-applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 14 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below: Fastening: Fastened to deck using Polygrip Fastener #14 with Polygrip Hex Plates or Dekfast 14 fasteners with Dekfast Galvalume Steel Hex Plates or OMG Heavy-Duty with OMG 3” Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrac Flat Bottom Plates or Trufast #14 HD with Trufast 3” Metal Insulation Plate or Simplex MAXX Cap Fasteners spaced 10” o.c. in 4” lap and 10” o.c. in three equally spaced staggered center rows. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, ENRGY 3, Multi-Max FA-3 Minimum 1.5” thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A Note: All insulation shall be adhered in a full mopping of approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 15 of 63 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 16 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type A(3): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. One or more layers of the following: Anchor Sheet: One ply of Elastobase (Poly/Sand, Sand/Sand), Polyglass G2 Base, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: Attach anchor sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates spaced 12” o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet. Base Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 ENRGY 3, ISO 95+ GL, ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, Multi-Max FA-3 Minimum 1.5” thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A FescoBoard Minimum ¾” thick N/A N/A Structodek High Density Fiberboard Roof Insulation Minimum ½” thick N/A N/A Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 17 of 63 Base/Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polybond, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered to DensDeck Prime or SECUROCK Gypsum-Fiber Board. *Requires torch-applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 18 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type A(4): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. One or more layers of the following: Anchor Sheet: One ply of Polyglass APP Base or Polyglass G2 Base fastened to the deck as described below: Fastening: Attach anchor sheet using 11 ga. annular ring shank and 1-5/8” diameter tin caps spaced 8” o.c. in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet. Base Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 ENRGY 3, ISO 95+ GL, ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, Multi-Max FA-3 Minimum 1.5” thick N/A N/A Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 FescoBoard Minimum ¾” thick N/A N/A Structodek High Density Fiberboard Roof Insulation Minimum ½” thick N/A N/A DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 19 of 63 Base/Ply Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered to DensDeck Prime or SECUROCK Gypsum-Fiber Board. *Requires torch-applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 20 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type A(5): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Elastobase, Elastobase P, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: 12 ga. annular ring shank nails and 1-5/8” tin-caps attached 6” o.c. in 4” lap and 6” o.c. in four equally spaced staggered center rows. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, H-Shield-CG, Multi-Max FA-3, ENRGY 3 Minimum 1” thick N/A N/A Note: All insulation shall be adhered to the anchor sheet with Millennium One-Step Foamable Adhesive, OlyBond 500, OlyBond 500 Green, Insta Stik™ Quik Set Insulation Adhesive, ICP Adhesives CR-20 applied in continuous rows 12” o.c. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation panels may be used as a top layer placed with the polyisocyanurate side facing down. Base/Ply Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base or one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 21 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type A(6): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below: Fastening: 12 ga. annular ring shank nails and 1-5/8” tin-caps attached 8” o.c. in 4” lap and 8” o.c. in four equally spaced staggered center rows. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, ENRGY 3, Multi-Max FA-3 Minimum 1.5” thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A Note: All insulation shall be adhered in a full mopping of approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 22 of 63 Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -67.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 23 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 screws at 6” o.c. System Type A(7): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below: Fastening: Fastened to deck using Polygrip Fastener #14 with Polygrip Hex Plates or Dekfast 14 fasteners with Dekfast Galvalume Steel Hex Plates or OMG Heavy-Duty with OMG 3” Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrac Flat Bottom Plates or Trufast #14 HD with Trufast 3” Metal Insulation Plates spaced 9” o.c. in 4” lap and 9” o.c. in four equally spaced staggered center rows. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, ENRGY 3, Multi-Max FA-3 Minimum 1.5” thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 DensDeck Prime or SECUROCK Gypsum-Fiber Roof Board Minimum ¼” thick N/A N/A Note: All insulation shall be adhered in a full mopping of approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 24 of 63 Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -82.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 25 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 screws at 6” o.c. System Type A(8): All insulation layers are adhered to a mechanically attached anchor sheet. Membranes subsequently adhered to insulation All General and System Limitations apply. Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below: Fastening: 12 ga. annular ring shank nails and 1-5/8” tin-caps attached 8” o.c. in 4” lap and 8” o.c. in four equally spaced staggered center rows. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, ACFoam-III, H-Shield, Polytherm-H, ENRGY 3, Multi-Max FA-3 Minimum 1.5” thick N/A N/A Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A Note: All insulation shall be adhered in a full mopping of approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of approved top layer insulation installed as the final membrane substrate. Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 26 of 63 Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -90.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 27 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type B(1): Base layer of insulation mechanically fastened, top insulation layer adhered with approved asphalt. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, H-Shield, Polytherm-H, ENRGY 3 Minimum 1.5” thick 1, 3 or 7 1:1.33 ft² Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density (See Roofing Application Standard RAS 117 for fastening details). Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 FescoBoard Minimum ¾” thick N/A N/A Structodek High Density Fiberboard Roof Insulation Minimum ½” thick N/A N/A Note: Optional top layer of insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as a top layer shall be installed with the polyisocyanurate face down. Base Sheet: (Optional if using ply sheet) One or more plies of Elastobase, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Ply Sheet: (Optional if using base sheet) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one to more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 28 of 63 Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 29 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type B(2): Base layer of insulation mechanically fastened, top layer adhered with approved asphalt. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, H-Shield, Polytherm-H, ENRGY-3 Minimum 1.5” thick 1, 3 or 7 1:1.33 ft² Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density (See Roofing Application Standard RAS 117 for fastening details). Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 FescoBoard Minimum ¾” thick N/A N/A Structodek High Density Fiberboard Roof Insulation Minimum ½” thick N/A N/A Note: Optional top layer of insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20-40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as a top layer shall be installed with the polyisocyanurate face down. Base Sheet: (Optional if using ply sheet) One or more plies of Elastobase, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Ply Sheet: (Optional if using base sheet) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base, one to more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 30 of 63 Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 31 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type B(3): Base layer of insulation mechanically fastened, top layer adhered with approved asphalt. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, H-Shield, Polytherm-H, ENRGY 3, Multi-Max FA-3, EnergyGuard Polyiso Insulation, Minimum 2.0” thick 1 (#14), 3 (#14), 7 or 10 1:1 ft² Note: Base layer shall be mechanically attached with fasteners and density described. Insulation panels listed are minimum sizes and dimensions; if larger panels are used the number of fasteners per board shall be increased maintaining the same fastener density (See Roofing Application Standard RAS 117 for fastening details). Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A Note: Top layer of insulation shall be adhered with approved asphalt within the EVT range and at a rate of 20- 40 lbs/100 ft2. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Composite insulation boards used as a top layer shall be installed with the polyisocyanurate face down. Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One or more plies of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 32 of 63 Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -75 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 33 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type C(1): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, H-Shield, Polytherm-H, ENRGY 3, Multi-Max FA-3, EnergyGuard Polyiso Insulation, Minimum 1.0” thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick 1 (#14), 3 (#14), 7 or 10 1:1.78 ft² Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 34 of 63 Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -45 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 35 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type C(2): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 Any approved Polyisocyanurate Listed in Table 2 Minimum 1.5” thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 Structodek High Density Fiberboard Roof Insulation Minimum ½” thick 1 or 3 1:1.33 ft² DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick 1 or 3 1:1.33 ft² Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Base Sheet: (Optional if using ply sheet in hot asphalt) One or more plies of Elastobase, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered to DensDeck Prime or SECUROCK Gypsum-Fiber Board. *Requires torch-applied ply or cap sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 36 of 63 Ply Sheet: (Optional if using base sheet in hot asphalt) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one to more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 37 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 4” o.c. System Type C(3): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 Any approved Polyisocyanurate Listed in Table 2 Minimum 1.5” thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 Structodek High Density Fiberboard Roof Insulation Minimum ½” thick 1 or 3 1:1.33 ft² DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick 1 or 3 1:1.33 ft² Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Base Sheet: (Optional if using ply sheet in hot asphalt) One or more plies of Elastobase, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA* self-adhered to DensDeck Prime or SECUROCK Gypsum-Fiber Board. *Requires torch-applied ply or cap sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 38 of 63 Ply Sheet: (Optional if using base sheet in hot asphalt) One ply of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one to more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -67.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 39 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type C(4): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 ACFoam-II, Polytherm, H-Shield, Polytherm-H, ENRGY 3, Multi-Max FA-3, EnergyGuard Polyiso Insulation, Minimum 1.0” thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick 1 (#14), 3 (#14), 7 or 10 1:1 ft² Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Base Sheet: One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR*, Polyflex SA Base* or XtraFlex SBS Base SA*, self-adhered. *Requires torch-applied ply or cap sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 40 of 63 Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -75 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 41 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type C(5): All layers of insulation are mechanically attached to roof deck. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 Any approved Polyisocyanurate Listed in Table 2 Minimum 1.5” thick N/A N/A Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Top Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 Structodek High Density Fiberboard Roof Insulation Minimum ½” thick 1 or 3 1:1.33 ft² DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick 1 or 3 1:1.33 ft² Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for insulation attachment. Base Sheet: (Optional if using ply sheet in hot asphalt) One or more plies of Elastobase, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Ply Sheet: (Optional if using base sheet in hot asphalt) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one to more plies of Type IV or VI ply sheet adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 42 of 63 Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -82.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 43 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type D(1): All layers of insulation and base sheet mechanically fastened. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 Any Approved Polyisocyanurate listed in Table 2 Minimum 1” thick N/A N/A Top Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 FescoBoard Minimum ¾” thick N/A N/A Structodek High Density Fiberboard Minimum ½” thick N/A N/A DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft., and four fasteners for any insulation board having no dimension greater than 8 ft. Base Sheet: One ply of Elastobase, Polyglass APP Base*, Polyglass G2 Base, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below. * Requires torch-applied ply or cap sheet. Fastening: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates, Dekfast 14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners 14 with Polygrip Hex Plates or Trufast #14 HD Fastener with Trufast 3” Metal Insulation Plates spaced 12” o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 44 of 63 Ply Sheet: (Optional) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 45 of 63 Membrane Type: SBS/APP Deck Type 1I: Wood, Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type D(2): All layers of insulation and base sheet mechanically fastened. Membranes subsequently adhered to insulation. All General and System Limitations apply. One or more layers of the following: Base Insulation Layer Insulation Fasteners (Table 3) Fastener Density/ft2 Any approved Polyisocyanurate Listed in Table 2 Minimum 1” thick N/A N/A Top Insulation Layer (Optional) Insulation Fasteners (Table 3) Fastener Density/ft2 FescoBoard Minimum ¾” thick N/A N/A Structodek High Density Fiberboard Minimum ½” thick N/A N/A DensDeck, DensDeck Prime, SECUROCK Gypsum-Fiber Board Minimum ¼” thick N/A N/A Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4 ft., and four fasteners for any insulation board having no dimension greater than 8 ft. Base Sheet: One ply of Elastobase, Elastobase P, Polyglass APP Base*, Polyglass G2 Base, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: * Requires torch-applied ply or cap sheet. Fastening: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates spaced 12” o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet. Ply Sheet: (Optional) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 46 of 63 Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 47 of 63 Membrane Type: SBS/APP Deck Type 1: Wood, Non- Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type E(1): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Polyglass APP Base*, Polyglass G2 Base, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS HT Base 650 fastened to the deck as described below: *Requires torch-applied ply or cap sheet. Fastening #1: (Polyglass APP Base or Polyglass G2 Base only) Attach base sheet using 11 ga. annular ring shank and 1-5/8” diameter tin caps spaced 8” o.c. in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet Fastening #2: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates, Dekfast 14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners #14 with Polygrip Hex Plates or Trufast #14 HD Fastener with Trufast 3” Metal Insulation Plates spaced 12” o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet. Ply Sheet: (Optional) One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 48 of 63 Membrane Type: APP Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type E(2): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass APP Base sheet fastened to the deck as described below: Fastening: Attach base sheet using 11 ga. annular grooved shank and 1” diameter caps spaced 6” o.c. in a 3” lap and 6” o.c. in four equally spaced staggered center rows. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 49 of 63 Membrane Type: SBS Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type E(3): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase (Sand/Poly), Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: Fastening: Attach base sheet using 11 ga. annular grooved shank and 1” diameter caps spaced 6” o.c. in a 3” lap and 6” o.c. in four equally spaced staggered center rows. Membrane: One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 50 of 63 Membrane Type: SBS Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type E(4): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase (Poly/Poly, Sand/Sand), Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: Fastening: Attach base sheet using Simplex MAXX Cap fasteners spaced 9” o.c. in a 2” lap and 12” o.c. in two equally spaced staggered center rows. Membrane: One ply of Polybond, Polyflex G, Polyfresko G or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -52.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 51 of 63 Membrane Type: SBS/APP Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type E(5): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase (Poly/Sand, Sand/Sand), Polybond, Polyflex, Polyglass APP Base*, Polyglass G2 Base, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: *Requires torch-applied ply or cap sheet. Fastening: Attach base sheet using OMG #14 Roofgrip fasteners with Flat Bottom Metal Plates spaced 12” o.c. in a 4” lap and 12” o.c. in two equally spaced staggered rows in the center of the sheet. Ply Sheet: (Optional) One or more plies of Polybond, Polyflex or XtraFlex APP S torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 52 of 63 Membrane Type: SBS/APP Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 screws at 6” o.c. System Type E(6): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass APP Base* or Polyglass G2 Base fastened to the deck as described below: * Requires torch-applied cap sheet. Fastening: Attach base sheet using 11 ga. annular ring shank and 1-5/8” diameter tin caps spaced 8” o.c. in a 4” lap and 8” o.c. in three equally spaced staggered rows in the center of the sheet. Ply Sheet: (Optional) One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base or one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20- 40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -60 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 53 of 63 Membrane Type: SBS/APP Deck Type 1: Wood, Non-Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type E(7): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass APP Base* or Polyglass G2 Base fastened to the deck as described below: *Requires torch-applied ply or cap sheet. Fastening: Attach base sheet using 12 ga. annular ring shank nails and 1-5/8” tin-caps attached 8” o.c. in 4” lap and 8” o.c. in four equally spaced staggered center rows. Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -67.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 54 of 63 Membrane Type: SBS/APP Deck Type 1: Wood, Non- Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with 8d ring shank nails at 6” o.c. System Type E(8): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass APP Base* or Polyglass G2 Base fastened to the deck as described below: *Requires torch-applied ply or cap sheet. Fastening: Fastened to deck using Polygrip Fastener #14 with Polygrip Hex Plates or Dekfast 14 fasteners with Dekfast Galvalume Steel Hex Plates or OMG Heavy-Duty with OMG 3” Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrac Flat Bottom Plates or Trufast #14 HD with Trufast 3” Metal Insulation Plate or Simplex MAXX Cap Fasteners spaced 10” o.c. in 4” lap and 10” o.c. in three equally spaced staggered center rows. Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -75.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 55 of 63 Membrane Type: APP Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 wood screws at 6” o.c. System Type E(9): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass APP Base* or Polyglass G2 Base sheet fastened to the deck as described below: *Requires torch-applied cap sheet. Fastening: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates spaced 6” o.c. in a 4” lap and 6” o.c. in three equally spaced staggered center rows. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -90.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 56 of 63 Membrane Type: SBS Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 wood screws at 6” o.c. System Type E(10): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase (Sand/Poly), Polyglass G2 Base, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening #1: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates spaced 6” o.c. in a 4” lap and 6” o.c. in three equally spaced staggered center rows. Fastening #2: (Only with asphalt applied cap sheets) Attach base sheet using Trufast #12 DP or Trufast #14 HD fasteners and Trufast 3” Metal Insulation Plates spaced 6” o.c. in a 4” lap and 6” o.c. in three equally spaced staggered center rows. Membrane: One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -90.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 57 of 63 Membrane Type: SBS/APP Deck Type 1: Wood, Non-Insulated Deck Description: Min. 15/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 wood screws at 6” o.c. System Type E(11): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass APP Base* or Polyglass G2 Base fastened to the deck as described below: *Requires torch-applied ply or cap sheet. Fastening: Fastened to deck using Polygrip Fastener #14 with Polygrip Hex Plates or Dekfast 14 fasteners with Dekfast Galvalume Steel Hex Plates or OMG Heavy-Duty with OMG 3” Galvalume Steel Plates or OMG #14 Roofgrip fasteners with Flat Bottom Plates or AccuTrac Flat Bottom Plates or Trufast #14 HD with Trufast 3” Metal Insulation Plate or Simplex MAXX Cap Fasteners spaced 9” o.c. in 4” lap and 9” o.c. in four equally spaced staggered center rows. Ply Sheet: (Optional) One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polybond, Polyflex, Polyglass APP Base, Polyglass HT Base 650, XtraFlex APP S, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base torch applied. Or One ply of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650 or XtraFlex SBS Poly Base adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -90.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 58 of 63 Membrane Type: SBS Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 wood screws at 6” o.c. System Type E(12): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of or Elastobase (Poly/Poly, Sand/Sand), Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: Fastening: Attach base sheet using Simplex MAXX Cap fasteners spaced 6” o.c. in a 2” lap and 6” o.c. in two equally spaced staggered center rows. Membrane: One ply of Polybond, Polyflex G, Polyfresko G or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -90.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 59 of 63 Membrane Type: SBS Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 wood screws at 4” o.c. System Type E(13): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase (Poly/Poly, Sand/Sand), Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: Attach base sheet using Simplex MAXX Cap fasteners spaced 6” o.c. in a 2” lap and 6” o.c. in three equally spaced staggered center rows. Membrane: One ply of Polybond, Polyflex G, Polyfresko G or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -105.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 60 of 63 Membrane Type: SBS Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #8 wood screws at 6” o.c. System Type E(14): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase, Elastobase P, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 fastened to the deck as described below: Fastening: 11 ga. Annular ring shanked nails and 1-5/8” tin-caps 6” o.c. in 4” lap and 6” o.c. in four equally spaced staggered rows. Tin-caps are primed with PG 100 Asphalt primer or XtraFlex 10 Asphalt Primer. Ply Sheet: (Optional) One or more plies of Elastobase, Elastobase P, Elastoflex S6, Elastoflex V, Elastoflex V 2.5, Polyglass HT Base 650, XtraFlex SBS Glass Base, XtraFlex SBS Glass Interply, XtraFlex SBS HT Base 650, XtraFlex SBS Poly Base, one or more plies of Type IV or VI ply sheet adhered in full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. Or One ply of Elastoflex SA V*, Elastoflex SA V FR*, Elastoflex SA V PLUS*, Elastoflex SA V PLUS FR* or XtraFlex SBS Base SA* self-adhered. *Requires torch-applied ply or cap sheet. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S, XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -112.5 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 61 of 63 Membrane Type: APP Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 wood screws at 4” o.c. System Type E(15): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Polyglass APP Base* or Polyglass G2 Base sheet fastened to the deck as described below: * Requires torch-applied cap sheet. Fastening: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates spaced 6” o.c. in a 4” lap and 6” o.c. in five equally spaced staggered center rows. Membrane: One ply of Polybond, Polybond G, Polyflex, Polyflex G, Polyflex G FR, Polyfresko G, Polyfresko G FR, XtraFlex APP G, XtraFlex APP S or XtraFlex Kool APP G torch applied. Or One ply of Elastoflex S6 G, Elastoflex S6 G FR, Elastoflex VG, Elastoflex VG FR, Elastoshield TSG, Elastoshield TSG FR, Polyfresko G SBS, Polyfresko G SBS FR or XtraFlex SBS Poly G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -120.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 62 of 63 Membrane Type: SBS Deck Type 1: Wood, Non-Insulated Deck Description: Min. 19/32" plywood or wood plank attached to structural supports at a maximum of 24” o.c. with #10 wood screws at 4” o.c. System Type E(16): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered. All General and System Limitations apply. Base Sheet: One ply of Elastobase (Sand/Poly), Polyglass APP Base*, Polyglass G2 Base, Polyglass HT Base 650, XtraFlex SBS Glass Base or XtraFlex SBS HT Base 650 sheet fastened to the deck as described below: * Requires torch-applied cap sheet. Fastening #1: Attach base sheet using OMG #12 Standard Roofgrip or OMG Heavy Duty fasteners with OMG 3 in. Round Metal Plates or OMG Flat Bottom Metal Plates spaced 6” o.c. in a 4” lap and 6” o.c. in five equally spaced staggered center rows. Fastening #2: (Only with asphalt applied cap sheets) Attach base sheet using Trufast #12 DP or Trufast #14 HD fasteners and Trufast 3” Metal Insulation Plates spaced 6” o.c. in a 4” lap and 6” o.c. in five equally spaced staggered center rows. Membrane: One ply of Elastoflex S6 G torch or hot asphalt applied. Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired coating or required fire classification. Maximum Design Pressure: -120.0 psf; (See General Limitation #7) NOA No.: 17-0824.09 Expiration Date: 09/13/22 Approval Date: 09/14/17 Page 63 of 63 WOOD DECK SYSTEM LIMITATIONS: 1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet. GENERAL LIMITATIONS: 1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire ratings of this product. 2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq. or mechanically attached using the fastening pattern of the top layer. 3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size shall be 4' x 4' maximum. 4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt application of either system shall be at a minimum rate of 12 lbs./sq. Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf 5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below 275 lbf. insulation attachment shall not be acceptable. 6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum fastener resistance value in conjunction with the maximum design value listed within a specific system. Should the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect or Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application Standard RAS 117. 7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect or Registered Roof Consultant (When this limitation is specifically referred within this NOA, General Limitation #9 will not be applicable.) 8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to Roofing Application Standard RAS 111 and applicable wind load requirements. 9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field, perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically referred within this NOA, General Limitation #7 will not be applicable.) 11. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and Rule 61G20-3 of the Florida Administrative Code. END OF THIS ACCEPTANCE