HomeMy WebLinkAboutNOA 3-9-22MIAMI DAREEKR
MIAMI-DADE COUNTY
PRj8)�315-2590
CT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RE��2 05 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474
, _rJnitttr F (786) 315-2590:•
NOTICE OF ACCEPTANCE (NOA) www.miamidade.Eov/economy
Karnak Corporation
330 Central Avenue
Clark, NJ 07066
�• � � 2' jam, .'_�. � ,r'�. �—._
FILE COPY ST. LUCIE COUNTY
SCOPE: SOCC
This NOA is being issued under the applicable rules and regulations governing the'use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this product
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner, the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use
of such product or material within their jurisdiction. RER reserves the right to revolve this acceptance if it is determined
by Miami -Dade County Product Control Section.that this. product or material fails to meet the requirements of the
applicable building code.
This product is approved as described herein and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Karnak 298 Alumin-R, 501 Elasto-Brite, 502 RC-W Elasto-Kote Base &
502 RC-W Elasto-Kote Coating.
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA No.20-0304.02 and consists of pages 1 through 7.
The submitted documentation was reviewed by Jorge L. Acebo.
MIAMI•DADE COUNTY
NOA No.: 21-0706.04
Expiration Date: 12/01/26
Approval Date: 10/28/21
Page I of 7
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Cement -Adhesive -Coatings
Material: - Elastomeric
SCOPE:
This approves "298 Alumin-R, 501 Elasto-Brite Coatings, 502 RC-W Elasto-Kote Base & 502 RC-W Elasto-Kote
Coatings" as a roof maintenance coating as manufactured by Karnak Corporation, as described in. this Notice of
Acceptance, designed to comply with the Florida Building Code and the High Velocity Hurricane Zone of the Florida
Building Code.
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
Test'
Product
Product
Dimensions
Specification
Description
298 Alumin-R
5 gallon pail &
ASTM D2824,
A single component; SBS rubber modified
Manuf. Location # 3
55 gallon drum
Type III
asphalt, formulated with aluminum
pigment to be used as a reflective
elastomeric coating.
501 Elasto-Brite
5 gallon pail &
ASTM D6083
A co -polymer elastomeric emulsion
Manuf. Location #1 & 2
55 gallon drum
exterior protective coating.
502 RC-W Elasto-Kote Base
5 gallon pail &
ASTM D6083
A thermoplastic, rubber -based,,
Manuf. Location #1
55 gallon drum
elastomeric coating.
502 RC-W Elasto-Kote
5 gallon pail &
ASTM D6083
A thermoplastic, rubber -based, white
Manuf Location #1
55 gallon drum
reflective, elastomeric coating.
5.02MS Karna-Flex
3.5 gallon bucket
TAS 139
An elastomeric, thermoplastic -rubber
Manuf. Location #1
&
mastic repair sealant
30 oz. caulking
cartridges
(white only)
505MS Karna-Flex WB
2 gallon bucket
TAS 139
An acrylic elastomeric, water -borne
Manuf Location #1
3.5 gallon bucket
mastic repair sealant
5 gallon pail
MANUFACTURING LOCATIONS:
1. Clark, N.J.
2. Port Everglades, FL.
3. Broadview, IL.
NOA No.: 21-0706.04
Expiration Date: 12/01/26
Approval Date: 10/28/21
Page 2 of 7
EVIDENCE SUBMITTED:
Test A2ency Test Identifier
Test Name/Report
Date
PIU Construction Materials KAR-087-02-01
ASTM D6083
06/18/15
Technologies, LLC KAR-090-02-01
ASTM C794/D903
08/19/16
KAR-116-02-01
ASTM D6083
11/20/17
KAR-117-02-01
TAS 139
10/05/17
KAR-118-02-01
TAS 139
10/05/17
KAR-079-02-01
ASTM D2824
08/21/14
PHYSICAL PROPERTIES OF COMPONENTS:
�Y.
Tirade name•; . 298 Alumii
Thickness: See System Approvals Below .
Specifications: ASTM D 2824, Type III (Non -Asbestos)
Description: A single component, SBS rubber modified asphalt, formulated with aluminum pigment to be
used as a reflective elastomeric coating for use over;
a
• Build Up Roof Systems: Apply with brush, roller, squeegee, or spray at a minimum
rate of 1-2 gal/100 ft2.
• Galvanized Metal Roof Apply with brush, roller, squeegee, or spray at a minimum
rate of 1-2 gal/100 ft2.
Container Sizes: 5-gallon pails and 55-gallon drums. Note all cautions on container label.
Systems Approvals: Methods of application and quantities shall comply with the specific Roof Assembly System's
Product Control Notice of Acceptance where it exceeds standards of this NOA.
NOA No.: 21-0706.04
Expiration Date: 12/01/26
Approval Date: 10/28/21
Page 3 of 7
PHYSICAL PROPERTIES OF COMPONENTS: (CONTINUED)
Trade name: 501 Elasto-Brite
Thickness: See System Approvals Below
Specifications: ASTM D 6083
Description: A co -polymer elastomeric emulsion exterior protective coating.for use over;
• SBS. Smooth Modified Bitumen Membranes: Apply 501 Elasto-Brite with brush,
roller or spray in two coats at. a. minimum rate of 1.5gal/1.00ft, per coat for a total
coverage of 3.0gal/100ft,
• APP Granulated Surfaced Modified Bitumen Membranes: Apply 501 Elasto-Brite
with brush, roller or spray in two coats at a minimum rate of 1.5gal/100ft2 per coat for
a total coverage of 5.OgaUl00ft2:
• Spray Polyurethane.FoamSystems' Apply 501 Elasto-Brite with brush, roller or
spray in two coats at a minimum rate of 1.5ga1/1002. per coat for a total coverage of
3.0ga1/100ft2..
• Single Ply TPO Membranes: Apply 501 Elasto-Brite with brush, roller or spray in
two coats at, a minimum rate of 1.5gaU1002 per coat fora total coverage of
3.0ga1/100ft2:
• Single Ply PVC Membranes: Apply 501 Elasto-Brite with brush, roller,or spray in
two coats at a minimum rate of 1.5gal/100ft2 per coat for a'total coverage of
3.Ogal/100ft2.
• Single Ply KEE Membranes: Apply 501 Elasto-Brite with brush, roller or spray in
two coats at a minimum rate of 1.5gal/100ft2 per coat for a total coverage of
3.Oga1/100ft2.
• Single Ply Hypalon Membranes: Apply 501 Elasto-Brite with brush, roller or spray
in two coats, at a minimum rate of 1.5gal/100ft2 per coat for a total coverage of .
3.0ga1/100ft2.
• Metal PVDF .(Kynar coated Metal): Apply 501 Elasto-Brite with brush, roller or
spray in. two coats at a minimum rate of 1.5ga1/100ft2 per coat for a total coverage of
3.0gaU1002.
• Galvanized Metal Roof: Apply 501 Elasto-Brite. with brush, roller or spray in two
coats at a minimum rate of 1.5gal/100ft2 per coat for a total coverage of,3.0gal/100ft2.
• Galvalume: Apply 501 Elasto-Brite with brush, roller or spray in two coats at a
minimum, rate of 1.5g41/l00ft2 per coat for a total coverage of 3.0ga1/100ft2.
• Concrete*: Prepare the surface by applying one coat of 4.04 Corrosion Proof at a
minimum rate of 1.5gal/100W. Apply 501 Elasto-Brite with brush, roller or spray in
two coats at a minimum rate of 1.5gal/100ft2 per coat fora total coverage of
3.0gal/100ft2:
This Application is not approved for use as a Waterproofing System.
*This application is only approved with products manufactured in the Clark, NJ facility.
Container Sizes: 5 gallon pail & 55 gallon drum. Note all cautions on container label.
Systems Approvals: Methods of application and quantities shall comply with the specific Roof Assembly System's
Product Control Notice of Acceptance where it exceeds standards of this NOA.
NOA No.: 21-0706.04
MIAMI•DADE COUNTY Expiration Date: 12/01/26
Approval Date: 10/28/21
Page 4 of 7
PHYSICAL PROPERTIES OF COMPONENTS: (CONTINUED)
Trade name:
Thickness:
Specifications:.
Description:
Container Sizes:
Systems Approvals:
MIAMI•DADE COUNTY
502 RC-W Elasto-Kote
See System Approvals Below
ASTM D 6083.
A thermoplastic, rubber -based exterior protective coating for use over; .
• Spray Polyurethane Foam Systems (SPUF): Apply 502 RC-W Elasto-Kote Base
with brush, roller or spray in one coat at a minimum rate of 1.5 ga1/1.00.ft2 followed
by 502 RC W Elasto-Kote applied with brush, roller or spray in one coat at a
minimum rate of 1.5ga1/l00ft2 per coat for a total coverage of 3.Oga1/100ft2.
• Single Ply TPO Membranes:. Apply 502 RC-W Elasto-Kote Base with brush, roller
or spray in. one coat at a minimum rate of 1.5 gal/100 ft2 followed by 502 RC-W
Elasto-Kote applied with brush, roller or spray in, one coat at a minimum rate of
1.5gal/100ft2 per coat for a total coverage,of 3.0gal/l00ft2:
• Single Ply.Hypalon Membranes (CSPE): Apply 502 RC-W Elasto-Kote Base with
brush, roller. or spray in one coat at a minimum rate of 1.5 gal/l00 ft2 followed by 502
RC-W Elasto-Kote applied with brush, roller or spray in one coat at a minimum rate
of 1.5gal/100ft2-per coat for a total coverage of 3.Ogal/100ft2.
• Galvanized Steel Metal Roofs: Apply 502 RC-W' Elasto-Kote Base with brush,
roller or spray in one coat at a minimum rate of 1.5 gal/100 ft2 followed by 502 RC-W
Elasto-Kote applied with brush, roller or spray in one coat at a minimum rate of
1.5gal/l00ft2 per coat for a total coverage of 10gal/1OOft2.
• EPDM Membranes: Using #507 SPC Primer/Wash (rinseable). Apply 502 RC-W
Elasto-Kote Base with brush, roller or spray in one coat at a minimum rate of 0.5
gal/100 ft2 followed by two coats of 502 RC-W Elasto-Kote applied with brush, roller
or spray at a minimum rate of 1.25 gaU100ftper coat for a total coverage of
3.0gal/1002.
• Concrete: Apply 502 RC-W Elasto-Kote Base with brush, roller or spray in one coat
at a minimum rate of 1.5 gal/100 ft2 followed by 502 RC=W Elasto-Kote applied with
brush, roller or spray in one coat at a minimum rate of 1.5ga1/100ft2 per coat for a
total coverage of 3.0gal/100ft2.
This. Application is not approved for use as a Waterproofing Svstem.
*This application is only approved with products manufactured in the Clark, NJ facility.
5 gallon pail & 55 gallon drum. Note all cautions on container label.
Methods of application and quantities shall comply with the specific Roof Assembly System's
Product Control Notice of Acceptance where it exceeds standards of this NOA.
NOA No.: 21-0706.04
Expiration Date: 12/01/26
Approval Date: 10/28/21
Page 5 of 7
PHYSICAL PROPERTIES OF COMPONENTS: (CONTINUED)
Trade name:
502MS Karna-Flex
Thickness:
See System Approvals Below
Specifications:
TAS 139
Description:
An elastomeric, thermoplastic -rubber mastic repair sealant for use sealing and waterproofing
cracks and splits on; spray polyurethane foam systems, single -ply TPO, PVC and EPDM
membranes, galvanized metal roof, concrete or wood roof systems as well as gutters, ,
fasteners, pinholes in metal, flashing and curb details. Also use to seal around skylights,
penetrations and roof equipment.
Application:
Apply 502MS Kama -Flex with a brush or caulking gun over cracks less than'/4" in
width. It's recommended to complete application by coating over with 502 RC-W
Elasto-Kote.
*This' application is only approved with products manufactured in the Clark, NJ facility. .
*PVC and TPO roof surfaces should be least 4 years old prior to :application.
Container Sizes:
3-gallon buckets & 30 oz. caul king .cartridges (white only). Note all cautions on container
label.
Systems Approvals:
Methods of application and quantities shall comply with the specific Roof Assembly System's
Product Control Notice of Acceptance where it exceeds standards of this NOA.
Trade name: 505MS Karna-Flex WB
Thickness: See System Approvals Below
Specifications: TAS 13.9
Description: An acrylic elastomeric, water -borne mastic formulated repair sealant for use on built-up
asphalt roofing, modified bitumen membranes and properly prepared, single -ply membranes
(TPO, PVC, Hypalon and EPDM), metal, concrete, spray polyurethane foam and plywood
roof substrates. Also used for sealing flashing, curbs and waterproofing metal roof seams,
gutters, fasteners, pinholes in metal and skylights.
Application:
Apply 505MS Kama -Flex WB with a brush or caulking gun over cracks less than'/4"
in width. It's recommended to complete application by coating over with appropriate
KARNAK approved acrylic coating.
Note: Allow to cure 24 hours before coating over, if desired. Not intended for use in
ponding areas.
*This application is only approved with products manufactured in the Clark, NJ facility.
Container Sizes: 2-gallon buckets, 3.5-gallon buckets and 5-gallon pails. Note all cautions on container label.
Systems Approvals: Methods of application and quantities shall comply with the specific Roof Assembly System's
Product Control Notice of Acceptance where it exceeds standards of this NOA.
QW4NOA No.: 21-0706.04•DAD, COUNTY Expiration Date: 070604
2/01/26
Approval Date: 10/28/21
Page 6 of 7
BUILDING PERMIT REQUIREMENTS:
Application for building permit shall be accompanied by copies of the following:
1. This Notice of Acceptance
2. Any other documents required by the building official or the Applicable Building Code in order to properly
evaluate the installation of this system.
LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
rating of this product.
2. Karnak products shall not be applied in inclement weather conditions.
3. The products listed herein are components of roof assemblies and are approved for use with roof assemblies that
list any of the products listed herein as part of their roof assemblies Notice of Acceptance.
4. All products listed herein shall have. an unannounced follow-up quality control program from an approved listing
agency. Follow up test results shall be made available to Miami Dade Product Control upon request.
5. Change in materials, use, or manufacture of any products listed herein shall be cause. for termination of this Notice
of Acceptance.
6. Karnak products shall be applied in accordance with manufacturer's published application instructions.
7. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61G20-3 of the Florida Administrative Code.
8. The use of a reinforcing fabric in a maintenance coating is only to enhance the coating's ability to deliver efficient
and long term and performance through the protection of the underlying roof system and in this particular use does
not become a roof system itself.
9. All approved .products listed herein shall be labeled in compliance with TAS 121 and shall bear the imprint or
identifiable marking of the manufacturer's name or logo, city and state of manufacturing facility, and following
statement: "Miami -Dade County Product Control Approved" or the Miami -Dade County Product Control Seal as
shown below.
QM1AMM1-DMADEWC0=UNTY
,...�
END OF THIS ACCEPTANCE
NOA No.: 21-0706.04
Expiration Date: 12/01/26
Approval Date: 10/28/21
Page 7 of 7