Press Alt + R to read the document text or Alt + P to download or print.
This document contains no pages.
HomeMy WebLinkAboutAPPROVED NOA 21-1209.01012MIAMI-DADE COUNTY
MIAMI-DIADE PRODUCT CONTROL SECTION
11805 5W 26 Street. Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE NOA w.y-v.miamidade.aov econom),
GAF
1 Campus Drive
Parsippany, NJ 07054
SCOPE.
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) andior the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this
acceptance, if it is determined by Miami -Dade County Product Control Section that this product or material fails to
meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code
DESCRIPTION: GAF Timberline HDI, Timberline" Natural Shadow', Timberline' NS, Timberline® American
Harvest, Timberline' AH, Timberline HOZI, Timberline" CS and Fortitude Shingles
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and;'or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatical;y terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA #19-0312.04 and consists of pages 1 through 6.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 21-1209.01
Expiration Date: 02/21;27
Approval Date: 01/06/22
Page 1 of 6
ROOFING ASSEMBLY APPROVAL
Category:
Roofing
Sub-Catezory:
Asphalt Shingles
Materials:
Laminate
Deck Type:
Wood
SCOPE
This approves GAF Timberline HW, Timberline' Natural Shadow", Timberline® NS, Timberline American'
Harvest®, Timberline' AH, Timberline HDZ", Timberline' CS and Fortitude Shingles as manufactured by GAF
as described in this Notice of Acceptance.
PRODUCT DESCRIPTION
Product Dimensions Test Product Descrintion
Specifications
GAF Timberline HD" 13 ` a x 39 ' TAS 110 Fiberglass reinforced heavy weight asphalt roof
Manufacturing shingle, with a laminate profile
Locations #1, 2, 3, 4, 5, 6, 7
GAF Timberline' Natural
13 ';`a" x 39
TAS 110
Fiberglass reinforced heavy weight asphalt roof
Shadow* and Timberline` NS
shingle, with a laminate profile
Manufacturing
Locations #1, 2, 3, 4, 5, 6, 7
GAF Timberline American
13 ' 'a x 39 3;'„..
TAS 110
Fiberglass reinforced heavy weight asphalt roof
Harvest®
shingle, with a laminate profile
Man it fact uring
Locations #2, 4, 6
GAF Timberline®AH
..
13 '/4" x 39 3/8
TAS 110
Fiberglass reinforced heavy weight asphalt roof
Manufacturing
shingle, with a laminate profile
Locations #2, 4, 6, 9
GAF Timberline HDZ*
13'/4"x 39 3/8
TAS 110
Fiberglass reinforced heavy weight asphalt roof
Manufacturing
shingle, with a laminate profile
Locations #1, 2, 3, 4, 5, 6, 7, 8, 9,
10
GAF Fortitude®
13 '/r " x 39 3/8"
TAS 110
Fiberglass reinforced heavy weight asphalt roof
Manufacturing
shingle, with a laminate profile
Location #4
GAF Timberline" CS
13'/4"x 39 3.8..
TAS 110
Fiberglass reinforced heavy weight asphalt roof
Manufacturing
shingle, with a laminate profile
Location #9
-Qd1DE COUNOA No.: 21-1209.01
MIAMINTY
,...� , Expiration Date: 02121?27
Approval Date: 01106!22
Page 2 of 6
MANUFACTURING LOCATION
1.
Tampa, FL
2.
Michigan City, IN
3.
Baltimore, MD
4.
Myerstown, PA
5.
Ennis, TX
6.
Tuscaloosa, AL
7.
Dallas, TX
8.
Shafter, CA
9.
Fontana, CA
10.
Minneapolis, MN
EVIDENCE SUBMITTED
Test Agency
Test Identifier
Test Name/Report
Date
Underwriters Laboratories, LLC
ASTM D3462
4788932264
12/13/19
ASTM D3462
4788717529
01/31/19
ASTM D3462
4787344101
07/25/16
TAS 107
4789225984
11/1/19
TAS 107
4788717529
01 /31 /19
TAS 107
OINK45803
04/13/94
TAS 107
06NK05159
08/09/06
TAS 107
04NK04273
02/20/04
TAS 107
05CA42840
1 I /1 1 /05
TAS 107
02NK4181 1
1 1/1 1 /02
TAS 107
03CA35209
10/17/03
TAS 107
04CA 13850
08/30/04
PRI Asphalt Technologies, Inc.
TAS 100
GAF-912-02-01
12/17/18
TAS 100
GAF-044-02-01
01/13/04
TAS 100
GAF-098-02-01
11/08/05
TAS 100
GAF- 10 1 -02-01
11 /09/05
TAS 100
GAF-116-02-02
03/23/06
TAS-100
ELK-083-02-01
10/ 16/02
ELK-084-02-01
10/ 15/02
ELK-085-02-01
10/ 14/02
ELK-0 8 6-0 2-01
10/24/0 2
ELK-087-02-01
10/21 /02
ELK-088-02-01
10/ 16/02
ELK-107-02-01
10/09/03
ELK-108-02-01
10/09/03
ELK-109-02-01
10/09/03
NOA No.: 21-1209.01
Expiration Date: 02/21/27
Approval Date: 01106/22
Page 3 of 6
LIMITATIONS
1, Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Shall not be installed on roof mean heights in excess of 33 ft.
3. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code,
INSTALLATION
1. Shingles shall be installed in compliance with Roofing Application Standard RAS 115.
2. Flashing shall be in accordance with Roofing Application Standard RAS 115
3. The manufacturer shall provide clearly written application instructions.
4. Exposure and course layout shall be in compliance with Detail 'A', attached.
5. Nailing shall be in compliance with Detail'B', attached.
LABELING
Shingles shall bear the imprint or identifiable marking of the manufacturer's name or logo, city and state of manufacturing
facility, and following statement: "Miami -Dade County Product Control Approved" or the Miami -Dade County Product
Control Seal as shown below.
BUILDING PERMIT REQUIREMENTS
1. Application for building permit shall be accompanied by copies of the following;
1.1 This Notice of Acceptance.
1.2 Any other documents required by the Building Official or the applicable code in order to properly evaluate
the installation of this system.
NOA No.: 21-1209.01
CM1AM&"DADffl=EC0jW
Expiration Date: 02/21!27
Approval Date: 01106.122
Page 4 of 6
DETAIL A
COURSE LAYOUT
Exposure
NOA No.: 21-1209.01
Expiration Date: 02121127
Approval Date: 01f06l22
Page 5 of 6
DETAIL B
OVERALL DIMENSIONS AND NAILING PATTERN
FOR GAF TIMBERLINE HD® TIMBERLINE® NATURAL SHADOW® AND TIMBERLINE® NS
39-3/8i'
(tm)
14-1t%3 - 17-112" 14-11?�g - 45mrn) "
(3 • 445mm1 (3-415mm)
it 6-112" - 9-112"
3 6-if1" - 9-112"
—(337�eij - 1ta5-x�tmml tt65.2�uwn-
trr-xrn»—------�---h --- --
tt .
ENHANCED NAILING PATTERN - six nails per shingle*
required by some local codes and required for enhanced wind coverage on cedain products
See limiled warranly for deiaifs.
These shingles MUST be nailed a nominal 6" (152mm) from bottom of
of shingle, above the cut outs, as shown. Nails must not be exposed.
Nail guide ine
5-W4' . 6.1 �4-
(146mm - 159mm;
from 6otiom of shingle
Self seal
adhesive
on back
OVERALL DIMENSIONS AND NAILING PATTERN
FOR TIMBERLINE HDe, TIMBERLINE® CS, TIMBERLINE"AH, AND FORTITUDE*'
13-114"
[3371a1f1a]
5-13/16' - 6.1?4-
(140 mm -159 mm)
For Mansard Roots
I
39-318' (1 m)
6-117 - 9-1.7 (165 mm - 241 r
.1f1' - 2.11?113 mm - 64 mm)
END OF THIS ACCEPTANCE
lZ-2.1Q'(13mm-64
- TARGET
NAIL ZONE
5-13116' - 7-9X
(148 rain - 194 mmu
NOA No.: 21-1209.01
Expiration Date: 02,2U27
Approval Date: 01106122
Page 6 of 6
3 1'22, 1:38 PM TFWZ.R21 - Prepared Roof -covering Materials I UL Product iQ
UL Product iQ'M I&
TFWZ.R21 - Prepared Roof -covering Materials
Prepared Roof -covering Materials
GAF R2'
1 Campus Dr
Pars-ppany, NJ 07054 United States
Asphalt glass fiber mat shingles - "Royal Sovereigns", 'Sentinelo', , SentinelO ASTM D3462", "Timberlines HD",'Timberline® Natural
Shadows", "Timberlines NS", "Timberline® Ultra HD",'Timberlines UHD", "Timberline® Coot Seriest", "Timberline® American Harvest'",
"Timberline® HDZ", "Timberline® AW or "Timberlines CS", "Fortitude'"", ''Timberline® ArmorShield'"' 11'.'Timberline-Z AS it", "Marquis
WeatherMaxs", "Grand Canyons", "Grand Sequoias", "Grand Sequoias ArmorShield"", "Grand Sequoias AS', "Camelots", "Camelot® 11",
"Slatelines", "Woodlands", "Sienna®" or "Glenwood®" for installation as a Class A prepared roof covering. Suitable for installation on minimum
3/8-in, thick plywood roof decks in combination with a minimum of one ply of "Shingle -Mates Roof Deck Protection", Type 15 or Type 30
underlayment. Also Classified in accordance with ASTM D3161/D3161M, Class F. Also Classified in accordance with ASTM D3462/D3462M. Also
Classified in accordance with ICC ES AC438.
Asphalt glass fiber mat shingles - "Pro -Start^' Starter Strip Shingles" for installation as a Class A prepared roof covering. Suitable for installation
on minimum 3/8-in. thick plywood roof decks in combination with a minimum of one ply of "Shingle -Mates Roof Deck Protection'. Type 15 or
Type 30 underlayment. Also Classified in accordance with ASTM D3161/D3161 M, Class F.
Asphalt glass fiber mat shingles - "Weather8locker" Premium Eave/Rake Starter Strip Shingles" for installation as a Class A prepared roof
covering. Suitable for installation on minimum 3/8-in. thick plywood roof decks in combination with a minimum of one ply of "Shingle -Mate®
Roof Deck Protection", Type 15 orI'ype 30 underlayment, Also Classified in accordance with ASTM D3161/D3161M, Class F. Also Classified in
accordance with ASTM D3462/O3462M.
Asphalt glass fiber mat shingles, "Royal Sovereigns", "Sentinels", "TimberlineT HD'. "Timberlines Natural Shadow&", "Timberlines NS",
"Timberline® Ultra HD", "Timberlines UHD", "Timberlines Cool Series®", "Timberline® American Harvest"", "Fortitude'"", "Marquis
WeatherMaxs", "Grand Canyons', 'Grand Sequoias" and "Camelott" for installation as Class A prepared roof cover ng when used with
minimum Type 30 underlayment over existing wood shingle roof.
Asphalt glass mat hip and ridge shingles- "Timbertexs Hip and Ridge" for installation as Class A prepared roof covering. Also been evaluated in
a: cordance with ASTM D3161/D3161 M, Class F when Henkel "PL Roofing and Flashing Sealant" or Sonneborn "NP1 Gun -Grade Polyurethane
Sealant" is applied as specified in manufacturer's application instructions."
Asphalt glass mat hip and ridge shingles, ' Zs Ridge Cap Shingles", "TimberCrest' Premium SBS-Mod red Ridge Cap Shingle", "TimberCrests
A5 Premium SBS-Modified IR Ridge Cap Shingles', "TimberTexs Premium Ridge Cap Shingles', -Ridglasss Premium Ridge Cap Shingles", for
installation as Class A prepared roof coverings. Also been evaluated in accordance with ASTM D3161/D3161 M. Class A.
Asphalt glass mat hip and ridge shingles, "Zs Ridge Cap Shingles", "TimberTexs Premium Ridge Cap Shingles", for installation as Class A
prepared roof coverings. Also been evacuated in accordance with ASTM D3161/D3161M, Class F when Henkel Corp. "Loctite PL Roof & Flashing
Polyurethane Sealant" is applied as specTed in manufacturer's installation instructions
Asphalt glass mat hip and ridge shingles, "Seal-A-RidgeD Ridge Cap Shingles", "Seal -A -Ridges ArmorShield"' and "Seal -A -Ridges AS SBS-
Modified IR Ridge Cap Shingles" for installation as Class A prepared roof coverings. Also been evaluated in accordance with ASTM
D3161/D3161M, Class F.
Asphalt glass mat hip and ridge shingles, "TimberCrest'' Premium SBS-Modified Ridge Cap Shingle" or"TimberCrests AS Premium SBS-
Modified IR Ridge Cap Shingles" for installation as Class A prepared roof covering. Also been evaluated in accordance w'th ASTM O3161/D3161M,
Class F when ASTM C920 Henkel "Loctite PL Roofing and Flashing Sealant" is applied as specified in manufacturer's installation instructions.
https:/liq.ulprospector-com/en/profile?e=148552 t 9
311122. 1:38 PM TFWZ.R21 - Prepared Roof -covering Materials I UL Product iQ
Last Updated on 2021-09-09
The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured
under UL's Follow -Up Service. Only those products bearing the UL Mark should be considered to be Certified and covered under UL's Follow -Up
Service. Always look for the Mark on the product,
UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions' 1- The Gu-de
Information, Assemblies, Constructions, Designs, Systems, and/or Certifications {files} must be presented in their entirety and on a non -misleading
manner, without any manipulation of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission
from UL" must appear adjacent to the extracted material. In addition, the reprinted material must include a copyright notice in the following
format: "© 2022 UL LLC"
hilpsd/iq,ulprospector,com/en/profile?e=148552 '24