No preview available
HomeMy WebLinkAboutEvaluation ReportMEMO I etc. Certificate of Authorization N32455 353 Christian Street, Unit #13 Oxford, CT 06478 (203)262-9245 ENGINEER EVALUATE Ili I TEST CONSULT GAF 1Campus Drive Parsippany, NJ 07054 (800) 766-3411 Evaluation Report 01506.04.08-1122 FL10626-1122 Date of Issuance: 04/25/2008 Revision 22: 06/09/2021 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the ar li 1 able rules and regulations governing the use of construction materials in the State of Florida. The documentatio ubmitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Flo Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 7t IEdition (2020) Florida Building Code sections noted herein. DESCRIPTION: GAF Roof Underlayments for use in FBC non-HVHZ j1Id ldictions LABELING: Labeling shall be in accordance with the requirementthe Accredited Quality Assurance Agency noted herein and FBC 1507.1.1. CONTINUED COMPLIANCE: This Evaluation Report is valid until such ta as the named product(s) changes, the referenced Quality Assurance or production facility location(s) changes, or. C� provisions that relate to the product(s) change. Acceptance of our Evaluation Reports by the named client con tes agreement to notify NEMO ETC, LLC of any changes to the product(s), the Quality Assurance or the produ-i facility location(s). NEMO ETC, LLC requires a complete review of its Evaluation Report relative to updated Cod ell uirements with each Code Cycle. ADVERTISEMENT: The Florida Product Approval Number (FL#) prec d d by the words "NEMOletc. Evaluated" may be displayed in advertising literature. if any portion of the Evalua Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report II be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site L a request of the Building Official. This Evaluation Report consists of pages 1 through 9. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration No. 59156, Florida DCA ANE1983 CERTIFICATION OF INDEPENDENCE: 1. NEMO ETC, LLC does not have, nor does it intend to acquire or will it distributing products it evaluates. 2. NEMO ETC, LLC is not owned, operated or controlled by any company I 3. Robert Nieminen, P.E. does not have nor will acquire, a financial inter which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial inte product. 5. This is a building code evaluation. Neither NEMO ETC, LLC nor Robert project on which this Evaluation Report, or previous versions tnereof, specifically for that purpose. The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 06/09/2021. This does not serve as an electronically signed document. re, a financial interest in any company manufacturing or acturing or distributing products it evaluates. any company manufacturing or distributing products for I any other entity involved in the approval process of the inen, P.E. are, in any way, Lhe Designer of Record for any is used for permitting or design guidance unless retained ©2019 NEMO ETC, LLC I Q-)NEMOletc- ROOFING COMPONENT EVALUATION: Product Category: Roofing Sub -Category: Underlayment Compliance Statement: GAF Roof Underlayments, as produ by GAF, have demonstrated compliance with the following sections of the 711 Edition (2020) Florida Building C 'd through testing in accordance with the following Standards. Compliance is subject to the Installation Requir nts and Limitations / Conditions of Use set forth herein. Section Property 1504.3.1 Wind resistance 1507.1.1. 1507.2.4. 1507.2 9.2 / Material standard R905.1.1, R905.2.8.2 1507.1.1.1(2&3, Exception), I ear Strength 1507.1.1.1(5) / R905.1.1.1(2&3, Exception), R905.1.1.1(5) 1507.1.1.1(2&3, Exception), Tensile strength 1507.1.1.1(5) / R905.1.1.1(2&3, Exception), R905.1.1.1(5) 1507.1.1.1(5) / R905.1.1.1(5) Liquid water transmission 1507.1.1 / R905.1.1 Material standard 1507.3.3, 11905.3.3 material standard 1507.11.2 Material standard TAS 110 Accelerated Weathering Standard Year FM 4474 2011 ASTM D1970 2015 ASTM D4533 2015 ASTM DS035 2011 ASTM D4869 2016 ASTM D6757 2016 FRSA/TRI, Sixth Edition 2018 ASTM D6164 2011 ASTM D4798 2011 Reference Date Entity Examination ERD (TST 6049) ASTM D1623 & FRSA/TRI (Stipp e) G34150.08.11 11/14/2011 ERD (TST 6049) ASTM D6164 (GA) G40630.01.14-2B 01/07/2014 ERD (TST 6049) ASTM D6164 (GA) G46160.09.14-3A 09/09/2014 ERD (TST 6049) ASTIVi D'1970 (GA) GAF-SC13285.03.17-3 03/01/2017 ERD (TST 6049) AS-1 M D2970 (GA) GAF-SC13285.03.17-4 03/01/2017 ERD (TST 6049) ASTM D1970 (GA) GAF-SC13285.03.1Y-1 03/08/2017 ERD (TST6049) ASI'M 01970 (IN) GAF-SC16440.12.17 12/31/2017 Intertek (T5T .15551 A5TM D4369 (Dadra, India) Physical Properties (ON) F8549.02-106-18 11/08/2016 4q-GAF-I9-SSMBB•03.A 05/13/2019 NEMO (TST 6049) NEMO (TST6049) ASTM D1970 4j-FTS-20-SSUDL-01.A 12/01/2020 NEMO (TST 6049) ASTM D4798, TAS 103 4j-GAF-20-SSUDL-02.A 03/15/2021 NEMO (TST6049) ASTM 04798 4j-FTS-2I-SSUDI. 02.A 06/09/2021 PRI (TST 5878) ASTM D1970 (IN) GAF-324-02-01 11/30/2011 PRI (TST 5878) ASTM D226 (OK) GAF-339-02-01 03/13/2012 PRI (TST 5878) =,5 T NI D4798 (NC) GAF•349-02-01 07/03/2012 PRI (TST 5878) Wing Upli t GAF-434-02-01 09/16/2013 PRI (TST 5378) Wind Uplift GAF-434-02-03 09/16/2013 09/16/2013 PRI (TST 5878) Wind Uplift ASTM D4533 (various) GAF-434-02-04 GAF-818-02-01 12/05/2017 PRI (TST 5878) PRI (TST 5878) ASTM D1970 (AL) MSA-047-02-01 04/1172018 PRI (TST 5878) ASTM D4533 (LA) GAF-826-02-01 06/4/2018 PRI (TST 5878) ASTIVI D4533 (Dadra, India) GAF-847-02-01 06/4/2018 PRI (TST 5878) ASTM D4533 (Dadra, India) GAF-914-02-01. 04/10/2019 PRI (TST 5878) ASTM D4533, D5035 (VA) 376T0012 07/15/2019 07/31/2019 PRI (TST 5878) ASTM U4533 (lJrnerkui Kilvani, id a) 376T0018 07/31/2019 PRI (TST 5878) ASTM D11533 [Parzai, India) 376T0018 Evaluation Report 01506.04.08-1122 MEMO ETC, LLC Certificate ofAathoritation K32a55 'GNF `.' Or Lti,:IGaf FL10626-R22 Revision 22: 06/09/2021 Roof Underlayme Page 2 of 9 ONEMOletc. Entity Examination Reference Date PRI (TST 58781 ASTM D1970 (AR) 376T0032 10/22/2019 PRI (TST 5878) ASTM D226 (S-CA) 376TOO54 02/18/2020 PRI (TST 5878) ASTM D4533 (Gujarat, India) 376TOO58 02/18/2020 PRI (TST 5878) ASTM D5035 (various) 376TO103 09/11/2020 PRI (TST 5878) ASTM D4533, D5035 (Rajasthan nc ia) 376TO111 12/22/2020 PRI (TST 5878) ASTM D4533, D5035 (Gujarat, Ir i is 376TO113 12/22/2020 UL (TST 1740) ASTM D67S7 (TX) 02NK22569 06/04/2002 PRI (TST 5878) ASTM D5035 (Gujarat, India) 376TO146 03/11/2021 PRI (TST 5878) ASTM D4533, D5035 (Rajasthan n(ia) 376TO161 05/07/2021 UL (TST 1.740) ASTM D6757 (NC) IONK11990 05/18/2011 NEMO ETC traceability FBC Cross -Listing 04/22/2020 NEMO I i aceability FBC Cross -Listing 04/08/2021 UL, LLC (QUA 9625) Quality Control Service Confirmation 03/23/2021 UL, LLC (QUA 9625) Quality Control Service Confirmation (AL) 05/04/2020 UL, LLC (QUA 9625) Quality Control Florida BCIS Current Material St ard Plant(s) Product 4.1 GAF Extended Dry -In Membrane ASTM Cl 0; Langley, BC Canada Liberty- SBS Self -Adhering Base/Ply ASTM D1 0 Mt. Vernon, IN 4.2 Sheet Savannah, GA ASTM D1 70 Mt. Vernon, IN 4.3 StormGuar& Film -Surfaced Leak Barrier Savannah, GA --'- — Arkadelphia, AR WeatherWatch" Mineral -Surfaced Leak ASTM D1 0 Mt. Vernon, IN 4.4 Barrier Savannah, GA Tuscaloosa, AL Deck -Armor"' Prernium Breathable Roof —1507.1,1.1(2&3, 1 !cc ption) / Dadra, India 4.5 Deck Protection R905.1.1.1(2&3, c ption) Dadra, India ------ -'- -' --:..----- Gujarat, India FeltBuster- Synthetic Roofing Felt 1507.1.1.1(2&3, c ption), (CPP) Rajasthan, India 4.6 (formerly FeltBusrcr- High- IroctionSynrhetic• I 1507.1.1.1(5) / R9 .1 1.1(2&3, (MIP) Rajasthan, India Roofing Felt) I Exception), R9 1.1.1(5) Richmond, VA --- Spartanburg, SC 4.7 - -'--- ... - — - - Shingle -Mate' Root Deck Protection �— ASTM D226, Ty p I ( able 1) Pryor, OK Shafter, CA 1S07.1..1.1(2&3, c ption) / North Bay, ON 4.8 StormSafe'"' Anchor Sheet i R905.1.1.1(2&3, c ption) - ----- --i-- i Dadra, India Tiger Paw'" Premium Roof Deck 1507.1.1.1(2&3, c ption) / Gujarat, India 4.9 Protection(formerlyTigerPaw-Roof Deck I R905.1.1.1(2&3, c ption) Parzai, India Protection) Umerkui Kilvani, India VersaShield°" Fire -Resistant Roof Deck ASTM D6 7 Conover, NC 4.10 protection ASTM D6 54 Savannah, GA 4.11 Ruberoid6' Mop Granule I FRSA/TRI -'1 - --- --- - — ASTivi D6 4 Savannah, GA 4.12 RuberoW' Mop G; ar:r,lc FIR FRSA/tRl -IS Evaluation Report 01506.04.08-1122 JEMO ETC, LLB :er[ificafe of Authorization n32J.55 �..i7t"^! iP:'":1; FEC' ri:.'•N•v+'+;{j, (J' TIOfJ FL10626-R22 021 Revision 22: 06ge GAF Roof Underlayme 3 of9 Page 3 of 5.1 This is a building code evaluation. Neither NEMO ETC, LLC nc of Record for any project on which this Evaluation Report, or or design guidance Unless retained specifically for that purpc 5.2 This Evaluation Report is not for use in FBC High Velocity H Dade Counties). 5.3 This Evaluation Report pertains to above -deck roof compon accordance with FBC requirements to the satisfaction of the 5.4 This Evaluation Report dues not include evaluation of fire cl limitations regarding roof assembly fire classification. R( concerning the use of foam plastic insulation. 5.5 GAF Roof Underlayments may be used with any prepared r( within FBC approval documents. If not listed, a request rr approval based on this evaluation combined with supportin€ 5.6 Allowable Roof Covers: NNEm*oletc. t Nieminen, P.E. are, in anyway, the Designer s versions thereof, is/was used for permitting ne Zone jurisdictions (i.e., Broward and Miami - Roof decks and structural members shall be in lority Having Jurisdiction. cation. Refer to FBC 1505 for requirements and to FBC 2603 for requirements and limitations (er where the product is specifically referenced made to the Authority Having Jurisdiction for for the prepared roof covering. — TABLE 1: ROOF COVER I I ONS --'r FBC Section: 1507.2 1507.3 1 07.4 and 1507.5 1507.7 1507.8 and 1507.9 Clay and Concrete Tile Metal Slate or Wood al Ad Velt _ a els Shingles Shingles Shakes Underlayment Aspha I Shingles Slate -Type Shingles Attach Set --'--T Yes Yes I I GAF Extended Dry -In Membrane Yes No No� Yes Yes Yes (jointstrips, 1507.1.1.3/ (Joint strips, 1507.1.1.3/ i R905.1.1.3) R905.1.1.3) — — Yes Yes Liberty"SBSSelf-AdhLnfi; vts No I I No I No No (Joint strips, 7507.1.1.3/ (Joint strips, 1507.1.1.3/ Base/PI Sheet Y ! i R905.1.1.3) R905.1.1 ) Yes Yes StormGuarda Film -Surfaced Leal: i Yes i No No Y s Yes Yes 60intstrips, (jointstrips, Barrier R905113) R905.1.1.3) — — — - Yes Yes WeatherWatch" Mineral-Surfat.ed i Yes No No o No No paint strips, IS07.1.1.3/ (Joint strips, 1507.1.1.3/ Leak Barrier {I Deck -Armor" Premium Breatha L7 i No No Y s Yes Yes 111905.1.1.3) No R905.1.1.3) No II Yes Roof Deck Protection __ —� -- _ FeltBuster` Synthetic Roofing Fan Yes No No I o No No No No Shingle -Mate° Roof Deck — i Yes No No o No No No No Protection I _ Tiger Paw'" Premium Roof Decl< Yes No No Y s Yes Yes No No Protection— VersaShield' Fire -Resistant Roof Yes No No o No No No No Deck Protection — --_� Yes (Cdp sheelin I o No No No No Ruberoid" Mop Granule No ; !C.n! sh, t•, in ,,i ll, s } I o No No No No Yes (Cap Sheet in Ruberoid" Mop Granule FR No i (Cap Sheet in 2-ply system) __...- ---- ---- I ply system)- see 5.6.1 - —. NEIVIO ETC, LLC Certificate of Aurhorizarion,r324S: GAF Roof Underlayme it Evaluation Report 01506.04.08-R22 FL10626-R22 Revision 22: 06/09/2021 Page 4 of 9 i N>=nno I ete. OTABLE 5.6.1 Adhesive -set is limited to use of following underlayment / ti -a hesive combinations. 1A: ALLOWABLE UNDERLAYMENT / TILE D ESIVE COMBINATIONS' Underlayment A hesive =11oProduct Approval Ruberoid° Mop Granule; Ruberoid'D Mop Granule FR Dupont "Tile B d " Roof Tile AdhesiveFL22525 5.7 Allowable Substrates: TABLE 2: SUBSTRATE OPTIONS FOR RED UNDERLAYMENTS Underlayment Application Primer Substrates GAF Extended Dry -In Membrane self -adhering None plywood Liberty" SBS Self -Adhering Base/Ply Sheet _ _ (Optional) StormGuard° Film. -Surfaced Leak Barrier self -adhering ASTM D41 I wood p y Weather Watch'"' Mineral -Surfaced Leak Barrier Liberty" SBS Self -Adhering Base/Ply Sheet StormGuard"' Film -Surfaced Leak Barrier self -adhering None ASTM D226 felt, Type II Weather Watch" Mineral -Surfaced Leak Barrier Liberty'" SBS Self -Adhering Base/Ply Sheet metal (flashing metal, valley metal, StormGuard"' Flm_Surfaced Leak Barrier self -adhering AS D41 etc.) Weather Wh' atcIvlineral-Surfaced Leal: Barrier Ruberoid°' Mop Granule_— hot asphalt ASTM D41 structural concrete Ruberoid" Mop Granule FIR _ Ruberoid" Nlop Grannie -_ -- ---- — hot asphalt None GAFGLASI #80 Ultima'" Base Sheet Ruberoid°' Mop Granule FR or Ruberoid® 20 Smooth 5.8 Attachment Limitations: 5.8.1 For use under mechanically attached NON -TILE prepared rc of: overings, attachment shall be in accordance with the manufacturer's installation instructions, but —for mec ni ally attached underlayments or base sheets - not less than FBC'1507.1.1 or R905.1.1. 5.8.2 For use under the roof systems, attachment shall be i accordance with the manufacturer's installation instructions, but - For mechanically attached base sheets o� less than: • FRSA/TRI Florida High Wind Concrete and Clay Rooj ril Installation Manual, Sixth Edition, Appendix A, Table 1 (for Two -Ply Asphalt Applied Hot Mop Under' ent) or • Section 5.8.3 herein (for other underlayment system 5.8.3 Wind Resistance for Underlayment Systems in Tile Roof A di cations: The following wind uplift limitations apply to underlayme L systems that are not prescriptive in the FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installation I o ual, Sixth Edition. The Maximum Design Pressure is the result of testing for wind load resistance based on al able wind loads, and reflects the ultimate passing divided by L (the Z to 1 margin of safety per FBC 504.9 has already been applied). pressure 5.8.3.1 Direc[ to Desk: The maximum design pressure for the selected assembly hall meet or exceed that required under FRSA/TRI Florida High Wind Concrete and Clay Roof Tile Installatio �VI nual, Sixth Edition, Appendix A, Table 1A or the critical (highest) design pressure determined in accordanci w th FBC 1609 or FBC Residential Chapter 3. I i Refer to Tile Manufacturer's or Adhesive Manufocturer's Florida Product p rovol for Overturning Moment Resistance Performance. Evaluation Report 01506.04.08-R22 MEMO ETC, LLC certlficare of Auchorizauon R32955 - . � `•' •:'': Jig. - .'ram.; j°r' i:;•:.;`; - „U FL10626-R22 • '': P_ 1 Revision 22: 06/ge GAF Roof Underlaymt I 5 of Page 5 of 9 I #1 Maximum Design Pressure = -442.5 psf. Deck: Min. 2,500 psi structural concrete to meet Fri Jurisdiction Base Sheet: GAFGLAS #75 Base Sheet, Tri-Ply #75 Base Sh Tri-Ply Ply 4 or GAFGLAS Flex Ply 6 applied in to 25 Ibs/square. Cap Sheet: Ruberoid° Mop Granule or Ruberoid° Mop G IV hot asphalt at 20 to 25 Ibs/square. 5.8.3.2 #2 #3 #4 Mechanically -Attached Base Sheet: The maximum design pressure for the selected assembly Florida High Wind Concrete and Clay Roof Tile Installation critical (highest) design pressure determined in accordance Alternatively, the maximum design pi ensure for the select( design pressure determined in accordance with FBC 1609 o shall employ an attachment density designed by a qualifie criteria. Commonly used methods are ANSI/SPRI WD1, Application Standard RAS 117. Assemblies marked with z 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (February Maximum Design Pressure = 45 psf. Deck: Min. 19/32-inch plywood to meet project Jurisdiction. Base Sheet: GAFGLAS"' #80 Ultima" Base Sheet or Rubel min. 1.25-inch long ring shank nails through 3 at the min. 4-inch wide side laps and 9-inch c in the field of the sheet. Cap Sheet: Ruberoid* Mop Granule or RuberoidO Mop GI IV hot asphalt at 20 to 25 Ibs/square. Maximum Design Pressure = -75 psf. Deck: Nlin. 19/32-inch plywood to meet project Jurisdiction. Base Sheet: GAFGLASO' #80 Uitima'" Base Sheet or Rubei min. 1.25-inch long ring shank nails through 3 aethe min. 4-Inch wide side laps and 8-Inch o in the field of the sheet. Cap Sheet: Ruberoid"' Mop Granule or Ruberoid' Mop G IV hot asphalt at 20 to 25 Ibs/square. Maximum Design.PrLssure = -97.5 psf. Deck: Min. 19/32-inch plywood to meet project Jurisdiction. Base Sheet: GAFGU\S" 080 Uitirna" Base Sheet or Rube min. 1.25-inch long ring shank nails through at the min. 2-inch wide side laps and 4-inch c of the sheet. Cap Sheet: Ruberoid* Mop Granule or RUberoid' Mop G IV hot asphalt at 20 to 25 Ibs/square. NEMO ETC, LLC Certificate ofAuthoriration #J 2455 GAF Roof Underlayi ONEMOleti requirements to satisfaction of Authority Having GAFGLAS #80 Ultima Base Sheet, GAFGLAS Ply 4, nopping of ASTM D312, Type IV hot asphalt at 20 le FR applied in full mopping of ASTM D312, Type i !II meet or exceed that required under FRSA/TRI nual, Sixth Edition, Appendix A, Table 1A or the I h FBC 1609 or FBC Residential Chapter 3. ssembly shall meet or exceed at least the Zone 1 C Residential Chapter 3. Elevated pressure zones li sign professional to resist the elevated pressure Loss Prevention Data Sheet 1-29 and Roofing )sterisk* carry the limitations set forth in Section ?ID) for enhancements. ents to satisfaction of Authority Having 20 Smooth mechanically attached with 12 ga., 1-5/8-inch diameter tin caps spaced 9-inch o.c. two (2), equally spaced, staggered center rows FR applied in full mopping of ASTM D312, Type uirements to satisfaction of Authority Having 20 Smooth mechanically attached with 12 ga., 1-5/8-inch diameter tin caps spaced 8-inch o.c. three (3), equally spaced, staggered center rows le FR applied in full mopping of ASTM D312, Type uirements to satisfaction of Authority Having 20 Smooth mechanically attached with 11 ga., 1-5/8-inch diameter tin caps spaced 4-inch o.c. four (4), equally spaced center rows in the field le FR applied in full mopping of ASTM D312, Type Evaluation Report 01506.04.08-R22 .FL10626-R22 Revision 22: 06/09/2021 Page 6 of 9 R1; - 0 M 5.9 Exposure Limitations: — TABLE 3: EXPOSURE LIMIT TI9NS Prepared Roof Cover Maximum Underlayment Installation Type Exposure (days) Deck -Armor"" Premium Breathable Roof Deck Protection, FeltBuster" Synth is Roofing Felt, Shingle -Mate = Roof Deck Protection, StormSafe' Anchor Shee i er Paw`"' Premium Roof Deck Protection, VersaShiel& Fire -Resistant Roof Deck Mechanically attached 30 Protection, Liberty'"' SBS Self -Adhering Base/Ply Sheet, StormGuard" Film -Su aced Leak Barrier and WeatherWatch` !\4ineral-Sur faced Leak Barrier Mechanically attached 180 GAF Extended Dry -In Membrane Adhesive -set tile roof system 180 Ruberoid° Mop Granule and Ruberoid" Mop Granule FR Mechanically attached UNLIMITED 5.16 Tile Slippage Limitations: When loading roof tiles on the uti; rlayment in direct -deck tile roof assemblies, the maximum roof slope shall be as follows. These slope limit s can only be exceeded by using battens during loading of the roof tiles. TABLE 4: TILE SLIPPAGE LIMITATIONS FOR DIRE - ECK TILE INSTALLATIONS Underlayment Profile —_ , St ging Method Maximum Staging Slope _ — Ruberoid® Mop Granule .Tile Rat d x. 10•tile stack 4:12 Flat Me 6 He stack (4 over 2) — 5:12 Lugged VIEX. 10-tile stack 5:12 Ruberoid° Mop Granule FR Flat or Lugged Ma 6' the stack (4 over 2) 5:12 Lugged , x. 10-tile stack 4:12 6.1 GAF Roof Underlaylnents shall be installed in accordance w 1i;; AF published installation instructions subject to the Limitations set forth in Section 5 herein and the specific d ed below. 6.2 Re -fasten any loose decking panels, and check for protrud g� nail heads. Sweep the substrate thoroughly to remove any dust and debris prior to application and prime t ubstrate (if applicable). 6.3 Deck -Armor"' Premium Breathable Roof Deck Protection o i�er Paw`"' Premium Roof Deck Protection: 6.3.1 Shall be installed in compliance with requirements for a syn a is underlayment in FBC 1507.1.1.1(2, Exception) or 1507.1.1.1(3, Exception) or FBC Residential R905.1.1.1(2 x eption) or R905.1.1.1(3, Exception) for the type of prepared roof covering to be installed, and the manufactu r' installation instructions. FBC requirements take precedence over the manufacturer's installation instruction 6.4 FeltBusterT1 Synthetic Roofing Felt: _ 6.4.1 Shall be instalied in compliance with requirements for a synt e6c underlayment in FBC 1507.1.1.1(2, Exception), 1507.1.1.1(3, Exception) or 1507.1.1.1(5) or FBC Residentia 05.1.1.1(2, Exception), R905.1.1.1(3, Exception) or R905.1.1.1(5) for the type of prepared roof 'covering t be installed, and the manufacturer's installation instructions. FBC requirements take precedence over the m facturer's installation instructions. NEMO ETC, LLC JEvaluation Report 01506.04.08-R22 eertificote OfAuthoriznrion #32455 ! J,: "' •;7?D} i�SC NONyi'.'ri.Y.UP.1 KiN FL10626-R22 GAF Roof Underlaymen Revision 22: 06/09/2021 Page 7 of 9 i I NNEMOletc. 6.5 StormSafel- Anchor Sheet: 6.5.1 StormSafer Anchor Sheet is limited to use as a mechanically tt ched base layer in 2-ply underlayment systems. 6.5.2 Shall be installed in compliance with requirements for a synt i at c underlayment'in FBC 1507.1.1.1(2, Exception) or 1507.1.1.1(3, Exception) or FBC Residential R905.1.1.1(2, x(eption) or R905.1.1.1(3, Exception) for the type of prepared roof covering to be installed, and the manufactur installation instructions. FBC requirements take precedence over the manufacturer's installation instructions 6.5.3 One the same day, install Liberty" 565 Self -Adhering Bas Ply; I StormGuard`" Film -Surfaced Leak Barrier or WeatherWatch" Mineral -Surfaced Leak Barrier over the Stor S fe`" Anchor Sheet. 6.6 Shingle-Mate,9 Roof Deck Protection: 6.6.1 Shall be installed in compliance with requirements for an ap o ed mechanically attached underlayment (ASTM D226, Type II) in FBC Table 1507.1.1.1 or FBC Residential Ta 905.1.1.1 for the type of prepared roof covering to be installed, and the manufacturer's installation instruct n FBC requirements take precedence over the manufacturer's installation instructions. 6.7 VersaShield° Fire -Resistant Roof Deck Protection: 6.7.1 Shall be installed in compliance with requirements for an ap o ed"mechanically attached underlayment (ASTM D6757) in FBC Table 1507.1.1.1 or FBC Residential Table R9 .1.1 for the type of prepared roof covering to be installed, and the manufacturer's installation instructiona FBC requirements take precedence over the manufacturer's installation instructions. 6.8 GAF Extended Dry -in Membrane, Libertyt" SBS Self-Adherin B se/Ply Sheet, StormGuard° Film -Surfaced Leak Barrier or WeatherWatchO Mineral -Surfaced Leak Barrier: 6.8.1 Shall be instalied in compliance with requirements for an ap ved self -adhering underlayment (ASTM D1970) in FBC 1507.1.1.1 or 1507.1.1.3 or FBC Residential R905.1.1.1 905.1.1.3 for the type of prepared roof covering to be installed, and the manufacturer's installation insiructio 6.8.2 Back -nailing is required. Back -nailing shall consist of ApprovE cap nails spaced 18-inch o.c., encapsulated within min. 4-inch side laps. 6.8.3 When installed over a mechanically attached, FBC Approved S M D226 Type II felt, the felt shall be fastened in accordance with FBC 1507.1.1 or R905.1.1. 6.8.4 GAF Extended Dry -In Membrane, Liberty'" SBS Self-Adherin B se/Ply Sheet, StormGuard® Film -Surfaced Leak Barrier or WeatherWatchO Mineral -Surfaced Leak Barrier be installed as a secondary water barrier using minimurn 9-incn wider roes to seal plywood deck joints prior i stallation of the primary underlayment system. 6.9 Ruberoid`"' Mop Granule; Ruberoid' Mop Granule FR: 6.9.1 Shall be installed in compliance with requirements as an alte ia e to the "Hot Asphalt Applied Cap Sheet" in the "Two Ply System" in the FRSA/TRI Florida High Wind Con fere and -Clay Roof Tile Installation Manual, Sixth Edition, and the manufacturer's installation instructions. 6.9.2 Refer to Section 5.8 herein for attachment limitations. 6.9.3 Refer to Table 4 for the staging limitations. Evaluation Report 01506.04.08-R22 DEMO ETC, LLC .. , , , , . :: , FL10626-R22 :ertificate of Authorization rf i]a 5 i ' - GAF Roof Underlaymenti,, Revision 22: 06/09/2021 Page 8 of 9