HomeMy WebLinkAboutNOA Modified Bitumen RoofingMlAMI, j A U 65 � � 2 911 7 MIAMI-DADE COUNTY
N P E r, Rf, I TT I IN G PRODUCT CONTROL SECTION
St. Lucie County, FL 11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 31525-99
NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
CertainTeed Corporation
18 Moores Road
Malvern, PA 19355
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: CertainTeed Modified Bitumen Roofing Systems over Wood Decks.
ft
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA #14-0224.03 and consists of pages 1 through 42.
The submitted documentation was reviewed by Alex Tigera.
zA NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 1 of 42
ROOFING SYSTEM APPROVAL
Category: Roofing
Sub -Category: Modified Bitumen
Material: APP/SBS
Deck Type: Wood
Maximum Design Pressure: -127.5 psf.
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions
Specification
Description
All Weather/Empire Base
39 3/8" x 65' 10";
ASTM D 4601, Type Asphalt coated, fiberglass reinforced
Sheet
Roll weight: 70 lbs.
II
base sheet.
(2 squares)
UL Type G2
Flexiglas Base Sheet
39 3/8" x 98'9"; Roll
ASTM D 4601, Type Modified Bitumen coated fiberglass
weight: 90 lbs.
II
base sheet.
(3 squares)
UL Type G2
Flintlastic Base 20
39 3/8" x 49' 6"; Roll
ASTM D 6163,
Modified Bitumen coated fiberglass
weight: 90 lbs.
Grade S, Type I
base sheet.
(1.5 squares)
Flintglas Ply Sheet Type IV
39 3/8" x 1647'; Roll
ASTM D 2178, Type Fiberglass, asphalt impregnated ply sheet.
weight: 38 lbs.
IV
(5 squares)
UL Type G 1
Flintglas Premium Ply Sheet
39 3/8" x 1647'; Roll
ASTM D 2178, Type Fiberglass, asphalt impregnated ply
Type VI
weight: 40 lbs.
VI
sheet.
(5 squares)
UL Type G1
Flintlastic STA
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Smooth surfaced APP Modified
weight: 87 lbs.
Grade S, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
Flintlastic GTA
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 1051bs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
Flintlastic GTA-FR
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 105 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
Flintlastic GMS
39 3/s" x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 94 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application.
NOA No.: 14-0529.02
MIAMI•DADE COUNTY
• • Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 2 of 42
1
f
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE
1
Test
Product
Product
Dimensions
Specification
Description
Flintlastic Premium GMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 101 lbs.
Grade G, Type II
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application.
Flintlastic FR-P
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type I
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Flintlastic Premium FR-P
39 3/s" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type II
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Flintlastic FR Dual Cap
39 3/8" x 32' 10"; Roll
ASTM D 6162,
Granule surfaced SBS modified
weight: 103 lbs.
Grade G, Type I
bitumen membrane with a nonwoven
(1 square)
polyester/fiberglass composite mat
reinforcement for use in cold or mop
applications.
Flintlastic FR Cap 30
39 3/8" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
weight: 86 lbs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications.
Flintlastic FR Cap 30 T
39-3/8" x 32' 10'; Roll
ASTM D 6163,
Granule surfaced SBS Modified
weight: 100 lbs.
Grade G, Type I
Bitumen membrane with fiberglass
(1 square)
mat reinforcement for torch
application.
Flintlastic Base 20 T
39-3/8" x 33'; Roll
ASTM D 6163,
Modified Bitumen, coated fiberglass
Weight: 81 lbs.
Grade S, Type I
base sheet for torch application.
(1 square)
Flintlastic FR Cap 30 CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
weight: 88 lbs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications. Covered with reflective
CoolStar Coating.
Flintlastic FR Cap 30 T
39 3/8." x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
CoolStar
weight: 1021bs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications. Covered with reflective
CoolStar Coating.
NOA No.: 14-0529.02
MIAMI-DADE COUNTY
• • •, 9 Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 3 of 42
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test Product
Product Dimensions Specification Description
Flintlastic GTA CoolStar 39 3/8" x 32' 10"; Roll ASTM D 6222, Granule surfaced APP Modified
weight: 1061bs. Grade G, Type I Bitumen membrane with non -woven
(1 square) polyester mat reinforcement for torch
application. Covered with reflective
CoolStar Coating.
Flintlastic GTA-FR CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 1061bs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application. Covered with reflective
CoolStar Coating.
Flintlastic GMS CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 971bs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application. Covered with reflective
CoolStar Coating.
Flintlastic Premium GMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
CoolStar
weight:103 lbs.
Grade G, Type II
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application. Covered with reflective
CoolStar Coating.
Flintlastic FR-P CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 103 lbs.
Grade G, Type I
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Covered with reflective CoolStar
Coating.
Flintlastic Premium FR-P
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
CoolStar
weight: 1031bs.
Grade G, Type II
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Covered with reflective CoolStar
Coating.
Flintlastic Ultra Poly SMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Smooth surfaced SBS Modified
Base Sheet
weight: 901bs. (1
Grade S, Type I
Bitumen Membrane with non -woven
squares)
polyester mat reinforcement for mop
applications.
Glasbase Base Sheet
36" x 98' 9"; Roll
ASTM D 4601, Type Asphalt coated, fiberglass base sheet.
weight: 75 lbs.
II,
(3 squares)
UL Type G2
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 4 of 42
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Product
Flintlastic Poly SMS Base
Sheet
Yosemite Venting Base Sheet
Flintlastic APP Base T
Flintlastic Ultra Glass SA
Black DiamondTm Base Sheet
APPROVED INSULATIONS:
Product Name
F1intBoard ISO
FlintBoardx ISO
ACFoam -II
High Density Wood Fiberboard
Dimensions
39 3/8" x 64' 3"; Roll
weight: 90 lbs.
(2 squares)
39 3/8" x 32' 10"; Roll
weight: 85 lbs.
(1 square)
39 3/8" x 65' 4"; Roll
weight: 100 lbs.
(2 squares)
39 3/8" x 33' 11"; Roll
weight: 73 lbs.
(1 square)
36" x 687'; Roll
weight: 78 lbs.
(2 squares)
Test
Product
Specification
Description
ASTM D 4601,
Modified Bitumen coated polyester
Grade S, Type II
base sheet.
UL Type G2
ASTM D 3909
Mineral Surfaced fiberglass reinforced
ASTM D 4897, Type buffer sheet.
II
UL Type G3
ASTM D 6509
Modified Bitumen coated fiberglass
base sheet.
ASTM D 1970
ASTM D 1970
TABLE 2
Product Description
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Wood fiber insulation board
Perlite Insulation Perlite insulation board
DensDeck, DensDeck Prime Water resistant gypsum board
H-Shield Polyisocyanurate foam insulation
ENRGY 3 Polyisocyanurate foam insulation
ENRGY 3 25 PSI Polyisocyanurate foam insulation
Multi -Max FA-3 Polyisocyanurate foam insulation
SECUROCK Gypsum -Fiber Roof Board homogenous fiber reinforced
CM1AM1WDADMEC0=UNTY
Self -adhering, fiberglass reinforced,
SBS modified bitumen base/ply sheet.
Self -adhering fiberglass reinforced
modified bitumen base sheet
Manufacturer
(With Current NOA)
CertainTeed Corporation
CertainTeed Corp.
Atlas Roofing Corp.
Generic
Generic
Georgia Pacific Gypsum LLC
Hunter Panels LLC
Johns Manville Corp.
Johns Manville Corp.
RMax Operating, LLC
USG Corp.
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 5 of 42
APPROVED FASTENERS:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions
(With Current NOA)
1.
Trufast #12 DP Fastener
Insulation fastener for wood
various
Altenloh, Brinch & Co. U.S.,
and steel decks
Inc.
2.
Trufast 3" Metal
Galvalume steel plate
3" round
Altenloh, Brinch & Co. U.S.,
Insulation Plate
Inc.
3.
FlintFast #12
Coated, carbon steel screw
various
CertainTeed Corp.
4.
FlintFast 3" Insulation
Galvalume AZ50 steel plate
3" round
CertainTeed Corp.
Plate
5.
FlintFast #14
Insulation fastener for wood
various
CertainTeed Corp.
and steel decks
6.
Simplex MAXX Cap
Polymer fastner
1" long
Simplex Nails, Inc.
7.
OMG #12 Standard
Insulation fastener for wood
various
OMG, Inc.
Roofgrip
and steel.
8.
OMG 3" Galvanized Steel
Galvalume stress plate
3" round
OMG, Inc.
Plates
9.
Trufast #14 HD Fastener
Insulation fastener for wood
various
Altenloh, Brinch & Co. U.S.,
and steel decks
Inc.
10.
OMG Heavy Duty
Insulation and membrane
Various
OMG, Inc.
fastener
11.
OMG 3 in. Round Metal
Galvalume AZ50 steel plate
Y round
OMG, Inc.
Plates
12.
AccutTrac Hextra
Carbon steel fastener
Various
OMG, Inc.
13.
AccuTrac Plates
Galvalume stress plate.
3" square
OMG, Inc.
14.
AccuTrac Flat Bottom
A2-SS aluminized steel plate
3" square
OMG, Inc.
Plates
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 6 of 42
APPROVED SURFACING/COATING OPTIONS:
TABLE 4
Chosen components must be applied according to manufacturer's application instructions. Any coating, listed
below, used as a surfacing, must be listed within a current NOA.
System Number Manufacturer Application
1. Generic Gravel applied at 4001bs/sq., adhered with flood coat of asphalt at
60 lbs/sq.
2.
Generic
Slag applied at 300 lbs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
3.
Karnak Corp.
Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
4.
CertainTeed Corp.
FlintCoat A-150 applied at an application rate of 1.5 gal/sq.
5.
Gardner Asphalt Corp.
APOC #212 Fibered Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
6.
Gardner Asphalt Corp.
APOC #400 Sunbrite applied at an application rate of 3 gal./sq.
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 7 of 42
EVIDENCE SUBMITTED:
Test Agency/Identifier
Name
Report
Date
Factory Mutual Research Corp.
FM 4470
3Y8A LAM
03/23/96
FM 4470
OD3A3.AM
04/04/97
FM 4470
2DOAO.AM
12/23/98
FM 4470
1D7A4.AM
11/09/98
FM 4470
3039046
06/15/10
FM 4470
3048520
09/19/13
Underwriters Laboratories, Inc.
UL 790
R11656
01/11/13
United States Testing Company
ASTM D 5147
97457-4
06/03/88
ASTM D 5147
97-457-2R
12/02/87
Momentum Technologies, Inc.
ASTM D 4601
AX31 G81)
09/05/08
ASTM D6164
AX31G8F
06/05/09
ASTM D6222
AX31 G8G
06/05/09
ASTM D 3909/ D 4897
AX31G8C
09/05/08
TrinitylERD
TAS 114(J)
3504.06.01-1
06/05/01
TAS 114(J)
3507.08.99-1
04/18/01
TAS 117 (B)
3503.10.06
10/10/06
TAS 117 (B)
06490.04.07-R1
06/27/07
TAS 114 (H)
Letter
04/05/06
TAS 114
3533.01.06
01/06/06
TAS 114
3521.07.04
07/29/04
TAS 117 (B)/ ASTM D 6862
C8500SC.11.07
11/30/07
TAS 114
C8370.08.08
08/19/08
ASTM Physical Properties
C10080.09.08-R4
03/25/10
ASTM D6164/D4798
C31410.01.11-2
01/10/11
ASTM D4601
C40050.09.12-1
09/28/12
ASTM D1970
C40050.09.12-2
09/28/12
ASTM D5147/D4798
C31410.10.10-R1
11/01/12
ASTM D5147/D.4798
C31410.01.11-1-R1
11/01/12
ASTM D1876
C35460.05.11
06/16/11
ASTM D1876, TAS 114 (I),
C42110.08.12
08/13/12
TAS 117 (B)
FM 4474/TAS 114
C39670.08.12
08/20/12
TAS 117B
C35500.02.11
02/09/11
ASTM D4798
C31410.01.11-2A-R1
02/21/13
ASTM D4798
C31410.12.13
12/05/13
ASTM D6222
C40050.12.13-R1
12/31/13
TAS 117, TAS 114
C30310.12.09-R1
03/07/14
ASTM D1876, TAS 114 (H),
C45620.03.14
03/27/14
FM 4474
ASTM D1876, TAS 114 (H),
C47320.03.14-R1
04/01/15
FM 4474
PRI Construction Materials
ASTM D6163
CTC-032-02-01
01/22/08
Technologies LLC
ASTM D6163
CTC-066-02-01
08/09/11
ASTM D6222
CTC-070-02-01
08/09/11
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 8 of 42
EVIDENCE SUBMITTED:
Test Agency/Identifier/Identifier Name
Report
Date
ASTM D6164/D4798
CTC-093-02-01
08/09/11
ASTM D2178
CTC-122-02-01
03/13/12
ASTM D2178
CTC-123-02-01
03/13/12
ASTM D4601
CTC-127-02-01
03/13/12
ASTM D6163
CTC-128-02-01
06/11/12
ASTM D6163
CTC-129-02-01
06/11/12
ASTM D6164
CTC-132-02-01
06/11/12
ASTM D6164
CTC-162-02-01
05/09/13
ASTM D6164
CTC-161-02-01
05/09/13
ASTM D6162
CTC-183-02-01
10/02/13
ASTM D6164
CTC-190-02-01
12/02/13
ASTM D1970
CTC-199-02-01
01/22/14
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 9 of 42
Ply Sheet: One ply of All Weather/Empire Base Sheet, Glasbase Base Sheet, Flexiglas Base Sheet,
(Optional) Flintlastic Base 20, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet or
one or more plies of Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI
adhered in a full mopping of approved asphalt applied within the EVT range and at a rate of 20-
40 lbs./sq. or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self -adhered
or Flintlastic Ultra Poly SMS Base Sheet torch applied.
Membrane: One ply of Flintlastic GMS, Flintlastic GMS CoolStar, Flintlastic Premium GMS, Flintlastic
Premium GMS CoolStar, Flintlastic FR Dual Cap, Flintlastic FR-P, Flintlastic FR-P CoolStar,
Flintlastic Premium FR-P, Flintlastic Premium FR-P CoolStar, Flintlastic FR Cap 30, Flintlastic
FR Cap 30 CoolStar adhered to base/ply sheet with approved mopping asphalt applied within
the EVT range and at a rate of 20 to 40 lbs./sq. or Flintlastic FR Cap 30 T or Flintlastic FR Cap
30 T CoolStar torch adhered to base/ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -60 psf. (See General Limitation #7)
Pressure:
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 16 of 42
Membrane Type:
Deck Type 1I:
APP Modified
Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank
System Type E(3): Base'sheet mechanically fastened.
All General and System Limitations apply.
Base Sheet: One ply of All Weather/Empire Base Sheet, Yosemite Venting Base Sheet, Flexiglas Base
Sheet, Flintlastic Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Glasbase Base
Sheet or Flintglas Premium Ply Sheet Type. VI mechanically attached as detailed below.
Fastening: Base sheet shall be lapped 4" and fastened with 11 ga. annular ring shank nails and approved tin
caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c.
Ply Sheet: One ply of All Weather/Empire Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Glasbase
(Optional) Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or one
or more plies of Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered in
a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq.
or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self -adhered or Flintlastic
STA or Flintlastic APP Base T torch adhered.
Membrane: Flintlastic GTA, Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar
torch adhered to base/ply sheet.
Surfacing: Any of the approved surfacing/coating options listed in Table 4.
(Optional)
Maximum Design -52.5 psf. (See General Limitation #7)
Pressure:
NOA No.: 14-0529.02
Expiration Date: 06/19/18
Approval Date: 09/24/15
Page 23 of 42