HomeMy WebLinkAboutEnergy Conservation Code:ORM 9405-2014
f
RESIDENTIAL ENERGY CONSERVATION CODE DOCUMENTATION CHECKLIST
640 C6VVz*\k De 1�0
Florida Department of Business and Professional Regulation
Simulated Performance Alternative (Performance) Method
Applications for compliance with the 2014 Florida Building Code, Energy Conservation via the
residential Simulated Performance method shall include
❑ This checklist
❑ A Form R405 report that documents that the Proposed Design complies with Section
R405.3 of the Florida Energy Code. This form shall include a summary page
indicating home address, e-ratio and the pass or fail status along with summary
areas and types of components, whether the home was simulated as a worst -case
orientation, name and version of the compliance software tool, name of individual
completing the compliance report (1 page) and an input summary checklist that can
be used for Feld verification (usually 4 pages/may be greater).
❑ Energy Performance Level (EPL) Display Card ("one page)
❑ Mandatory Requirements(three pages)
Required prior to CO for the Performance Method:
❑ Air Barrier and Insulation inspection Component Criteria checklist (Table R402.4.1.1 -
one page)
❑ A completed Envelope Leakage Test Report(usually one page)
❑ If Form R405 duct leakage type indicates anything other than "default leakage", then a completed
Form R405 Duct Leakage Test Report (usually one page)
File Copy
912212016 11:35:56 AMEnergyGauge(& - USRCZB v5.1 Page 1 of 1
FORM R405-2014 >
FLORIDA ENERGY EFFICIENCY CODE FOR BUILDING CONSTRUCTION
Florida Department of Business and Professional Regulation - Residential Performance Method
l7 yt>exoYN
yN�'
aroject Name Express 1672 Aria RIGHT PSL
Builder name.
CM>^�"11
St>aet 8% ccw'"l' Cx—
Permit Office
City State. Zip ST LUCIE , FL,
Permit Number
C vner. Express Homes
J'_dsciction Se0..VLk- L U LL-2 ��•�
i astgn Location F_, ST_LUCiE_CO_INTL
County, St. Lucie (F`orida Climate Zone 2 )
1 Nev" construction o- exis`iny ;few (Fenn Pl,nsl
- Wall Tvc'es(1707 2 sgft )
insulat,on Area
a Csncrete Bior.�� - Irt Piaui, Exter.or
R=4.1 13G2.20 ft'
�!q
i
2 Single family of r.1 rltipla family ng family
r F• e,_e
,, ,ar1°Jost• Adla..er,t
P.=13 v 3115 04 ft2
3 lumder of urns if rvitio e family 1
C NIA.
R= ftz
d N.:�.
it' R=
4 Nurrber of Bed'ooms 3
f0 Ceiling Types (t672 agft 1
InsLlation Area
Is this a 'Norse case') Yes
a. Under Atic :Nentedj
R=38 0 1672 Ot; ft'
6 Conditioned 'lcor area above grade (t'} 1672 28CZ-02929
b W
R=
r_ MIA
R=
13C1`diton, ed illcr ar_a be:ovi ra,de if 1 0
11 Duz
R sz
YVi=;ir:;�s? i 83 ' agft ! Descrin-ion Area
a SI-P At:io Pet attic. AH 1Aho,a House 6 163 6
a U-r z:tor' fib!. U=�• 24
Sr'Gw SHGC=0 35
iG CcCls'tg systems
ot„
i<.�. rhf Efficiency
r is
4 U-Factor Dbl. U=0 63 4`) ? j
a Centrai nit i i
290 SEERAS CO
SHGC S1HG0=0.32
13 Hea+17g systems
cBtulrr-fficiency
o U-JJFactor N'A Ft`
a Electric Neat purnp
27 0 NSPF g 00
i♦-1-Sr-
d� G
f'ifea YID jnte'�iA'tera'�C V`te'~a r••�^g Llel:'tti 227C.
14 Not w2'e- S%SiemS
Area 4,n ghted n: age S-GC 343
- E!actrir_
Cap 67 ga9ur5
8 -.c,r TyCas ,'3' O s,r t t ^:5.:1a"lor Area
EF 0 980
3 AlaJ-C''af8G8 tN.g, 1'Stla,.i•-n „n 1672 00ft
fe!, es
ft-
`d,.4
S Credits
Pstat.
Tcta; Proposed Mcd—jifed Loads: 53.07
SS
PASS
fi
Gl _sir !oor Area 0 i i
Total Baseiin= Loads 5622
i hereby Certify "hat the planS and specf?;Cat,ons covered by
c
Energy
Review of the plans and
ecincations covered b this
y
0i1K �r�
t;^.ts Calculation are :n GOr"rllanGe with the F16rida
—ode, T A [ E'
f� f
s p'
., G
calculation indicates ornpliance
Cai25
with the Florida Energy Code.
,
ij
Before construction is completed
PREPARED 8`i -- — - —
�..- • p
�- DATE
this building will be inspected for
compliance with Section 553.908
ti
I hereby certi y tna: this building. as deli nee, i15,1n COMpliar:ce
v
t
Florida Statutes
•e,
with tee Florida Energy CC IV,
W�'�
CVIiNEG' GEtiT
BUILDIN 0FFICIAL : -- -
— — -- ------
- Compliance requires certification by the air handier unit manufacturer that the air handier enclosure qualifies as
certified factory -sealed in accordance with R403.2.2.1.
- Compliance requires an Air Barrier and Insulation Inspection Checklist in accordance with R402.4.1.1 and an envelope leakage
test report in accordance with R402.4.1.2.
- Compliance with a proposed duct leakage On requires a Duct Leakage Test Report confirming duct leakage to outdoors,
tested in accordance with Section 803 of RESNET Standards, is not greater than 0.030 On for whole house.
File COPY
11:2512017 2'39 PNI Ener'gyGaugez' USA - FlaRe52014 Section R405 4 1 Comp fa�c are Page 1 or 4
A A
i-'VRIVi R4u J-LV I`t
i
' PROJECT
Title:
Building Type:
Owner:
# of Units:
Builder Name:
Permit Office:
Jurisdiction:
Family Type:
New/Existing:
Comment.
Express 1672 Aria PSL RICH Bedrooms: 3
User Conditioned Area: 1672
Express Homes Total Stories: 1
1 Worst Case: Yes
Rotate Angle: 225
Cross Ventilation: No
Whole House Fan: No
Single-family
New (From Plans)
Address Type: Street Address
Lot #
BlocklSubDivision:
PlatBook:
Street:
County: St. Lucie
City, State, Zip: ST. LUCIE ,
FL,
CLIMATE
1! Design Location
IECC Design Temp
TMY Site Zone 97.5 % 2.5 %
Int Design Temp Heating Design Daily Temp
Winter Summer Degree Days Moisture Range
FL, ST_LUCIE_CO INTL FL_VERO SEACH_MUNI 2 39 90
70
75 299 58
Medium
BLOCKS
Number
Name
Area Volume
}
Blockl
1672280 14716.1
SPACES
Number
Name
Area Volume Kitchen Occupants
Bedrooms
InfilID Finished Cooled
Heated
1
Whole House
1672.28 14716.1 Yes 4
3
1 Yes Yes
Yes
FLOORS
#
Floor Type
Space Perimeter R-Value
Area
Tile Wood
Carpet
1 Slab -On -Grade Edge Insulatio Whole House 194 ft 0
1672 ft2
---- 0.7 0
0.3
ROOF
V #
Type
Roof Gable Roos
Materials Area Area Color
Solar
Absor.
SA Emitt Emitt Deck
Tested Tested Insul.
Pitch
(deg)
1
Hip Composition shingles 1870 ft2 0 ft2 Dark
0.9
No 0.9 No 0
26.6
ATTIC
V #
Type
Ventilation Vent Ratio (1 in)
Area
RBS IRCC
1
Full attic
Vented 300
1672 ft2
N N
CEILING
1 #
Ceiling Type
Space R-Value Ins Type Area Framing Frac Truss Type
}
Under Attic (Vented)
Whole House 38 Blown 1672 ft2 0.11 Wood
9i2212016 11:36 AM EnergyGaugeO USA - FlaRes2014 Section R405.4.1 Compliant Software Page 2 of 4
FORM R405-2014
'
WALLS
Cavity Width Height
Sheathing
Framing Solar
Below
Adjacent S ace
P
1
N=>SW Exterior Concrete Block - Int insWhole House
4.1 38.8 0 8.8
0
341.4 ft-'
0
0 0.8
0
_
2
W=>SE Exterior Concrete Block - Int InsVVhole House
4.1 58.4 0 8.8
0
513.9 ft2
0
0 0.8
0
Y_ 3
S=>NE Exterior Concrete Block - Int InsVVhole House
4.1 17 0 8.8
0
149.6 ft2
0
0 0.8
0
4
E=>NW Exterior Concrete Block - In' InsWhole House
4.1 44 0 8.8
0
387.2 ft2
0
0 0.8
0
_
5
S=>NE Garage Frame - Wood Whole House
13 21.8 0 8.8
0
191.8 ft,
0
0.8
0
_
6
E=>NW Garage Frame - Wood Whole House
13 14 0 8.8
0
123.2 ft2
0
0.23 0.8
0
DOORS
# Ornt Door Type Space
Storms
U-Value
Ft
Width
In
Height
Ft In
Area
1 S=>NE Insulated Whole House
None
.4
3
68 20.4 ft2
2 S=>NE Insulated Whole House
None
.4
2
8
16 ft2
WINDOWS
Orientation shown is the entered orientation (=>) changed to Worst Case.
Wall
Overhang
.� (
# Omt ID Frame Panes NFRC U-Factor SHGC
Area
Depth
Separation
Int Shade
Screening
1 N=>SW 1 Vinyl Low-E Double Yes
0.34 0.35
62A ft2
1 ft 0 in
2 ft0 in
None
None
2 N=>SW 1 Vinyl Low-E Double Yes
0.34 0.35
31.2 ft2
8 ft 0 in
2 ft 0 in
None
None
3 W=>SE 2 Vinyl Low-E Double Yes
0.34 0.35
15.6 ft2
1 ft 0 in
2 ft 0 in
None
None
4 S=>NE 3 Vinyl Low-E Double Yes
0.34 0.35
31.2 ft2
1 ft 0 in
2 ft 0 in
None
None
5 S=>NE 3 Vinyl Low-E Double Yes
0.34 0.35
2.5 ft2
7 ft 0 in
2 ft 0 in
None
None
6 W=>SE 2 Vinyl Low-E Double Yes
0.63 ' 0.32
40.8 ft2
1 ft 0 in
8 ft0 in
None
None
GARAGE
# Floor Area Ceiling Area Exposed Wail Perimeter
Avg. Wall Height
Exposed Wall Insulation
1 445.12 ft2 445-12 ft'
64 ft
8.8 ft
13
INFILTRATION
#
Scope Method SLA CFM 50 ELA EgLA
ACH
ACH 50
1 Wholehouse Proposed ACH(50) .00028 1226.3 67.32 126.61
.2097
5
HEATING SYSTEM
V
# System Type Subtype
Efficiency
Capacib(
Block
Ducts
1 Electric Heat Pump Split
HSPF:9
27 kBtuihr
1
sys#1
9122/2016 11:36 ANI EnergyGauge2 USA - FiaRes2014 Section R405.4-1 Compliant Software Page 3 of 4
FORM R405-2014
COOLING SYSTEM
# System Type
Subtype
Efficiency
Capacity
Air Flow
SHR
Block
Ducts
1 Central Unit
Split
SEER: 16
29 kBtulhr
931 cfm
0.73
1
sys#1
HOT WATER SYSTEM
# System Type
SubType
Location
EF Cap
Use
SetPnt
Conservation
1 Electric
None
Garage
0.98 50 gal
60 gal
120 deg
None
SOLAR HOT WATER SYSTEM
Collector
Storage
V/ FSEC
Cert # Company Name
System Model # Collector Model # Area
Volume
FEF
ft2
None None
DUCTS
--- supply l ~--
— Return ---
Air
Handier
CFM 25 CFM25
TOT OUT QN
RLF
HVAC #
Heat Cool
V # Location R-Value
Area
Location
Area Leakage Type
1 Attic
6 183.5 ft
Attic
63.61 ft Prop. Leak Free
Whole Hou
--- cfm 50.2 cfm 0.03 0.60
1 1
TEMPERATURES
Programable Thermostat: Y
Ceiling Fans:
Coaling Jan [ Feb
[[ Mar
[
j Apr
1 May Jun [X] Jul
1 May [ ]Jun [ ]Jul
X Aug(Xj
Aug
Se
! !Sep 1XI
Oct
N ov
X� Nov
DecOct
� Dec
Heating Jan X Feb
Feb
[X Polar
[X, Mar
(]Apr
(X]
Apr
j May [ ]Jun [ ]Jul
Aug
[ 1 Sep Oct
Venting Jan t
Thermostat Schedule: HERS 2006 Reference
Hours
8 9
10
11
12
Schedule Type
1
2
3
4 5 6
--
Cooling (WD) AM
78
78
80
78
78
78 78 78
78 78 78
78
78
78 80
78 78
80
78
80
78
80
78
PM
Cooling (WEH) AM
80
7
78
78
78
78 75 78
78 78 78
78
78
78 78
78
78
78
78
78
78
PM
78
78
Heating (WD) AIM
66
66
68
66
68
66 66 68
68 68 68
68
68
68 68
68 68
68
68
68
66
68
66
PM
Heating (WEH) A11A
68
66
66
06
as 6R 68
68
68 68
68
66
68
66
tINI oo
9i22/2016 11:36 AM EnergyGaugeiu USA - FlaRes2014 Section R405.4.1 Compliant Software Page 4 of 4
FORM R405-2014 ,
ENERGY PERFORMANCE LEVEL (EPL)
ESTIMATED ENERGY PERFORMANCE INDEX* = 94
The lower the EnergyPerformance Index, the more efficient the home.
1. New construction or existing
2. Single family or multiple family
3. Number of units, if multiple family
4. Number of Bedrooms
5 Is this a worst case?
6. Conditioned floor area (ft2)
7. Windows"
Description
a. U-Factor
Dbl, U=0 34
S ;GC
SHGC=O 35
b. U-Factor.
Dbl, U=0.63
SHGC•
SHGC=0.32
c U-Factor•
NIA
SHGC'
d. U-Factor.
NIA
SHGC
Area %Weighted Average Overhang Depth'
Area Weighted Average
SHGC'
, ST. LUCIE, FL,
New (From Plans)
g. Wall Types
Insulation
a. Concrete Block - Ini Insul, Exterior
R=4.1
Single-family
b. Frame - Wood, Adjacent
R=13.0
1
c. NIA
R=
d. NIA
R=
3
10. Ceiling Types
Insulation
Yes
a. Under Attic (Vented)
R=38.0
1672
b. N/A
R=
c. N/A
R=
Area
11. Ducts
142.89 ft2
a. Sup: Attic, Ret: Attic, AH. Whole House
40.80 ft'
12 Ceo ing systems
ft2 a Central Unit
z
ft 13 Heating systems
a. Electric Heai Pump
2.270 ft.
0 343
S. Floor Types Insulation Area
a. Slab -On -Grade Edge Insulation P.=0.0 1672.00 ft2
b N/A R= ft•
c. N/A R= ft
14. Hot water systems
a Electric
b Conservation features
None
15. Credits
I certinj that this home has complied with the Florida Energy Efficiency Code for Building
Construction through the above energy saving features which will be installed (or exceeded)
in this home before final inspection. Otherwise, a new EPL Display Card will be completed
based on installed Code compliant features.
I
Builder Signature: Date:Z4�__
Address of New Home: 8q�61,t(ae City FL Zip:�pr�.
Area
1392.20 ft'
315.N W
ft2
ft2
Area
1672 00 ft2
ft2
ft�
R ,t2
6 183.5
kBtu/hr Effc!ency
29.0 SEER.16.00
kBtuihr Efficiency
27,0 HSPF:9 00
Cap 50 gallons
EF. 0,98
Pstat
115E 57%
'Note: This is not a Building Energy Rating. if your Index is below 70, your home may qualify for energy efficient
mortgage (EEM) incentives if you obtain a Florida EnergyGauge Rating. Contact the EnergyGauge Hot;ine at (321)
638-1492 or see the EnergyGauge web site at energygauge.com for information and a list of certified Raters. For
information about the Florida Building Code, Energy Conservation, contact the Florida Building Commission's support
staff.
"Label required by Section R303.1.3 of the Florida Building Code, Energy Conservation, if not DEFAULT.
gi22(2016 11.26 AN1 EnergyGaugeS USA - FlaRes2014 - Section R405.4 1 Compliant Software Page 1 of 1
FORM R405-2014
Flr)riri;; np-partment of Business and Professional Regulations
Residential Whole Building Performance and Prescriptive Methods
ADDRESS: Permit Number. ST. LUCIE , FL,
MANDATORY REQUIREMENTS See individual code sections for tuli cietaks.
❑ 401.3 Energy Performance Level (EPL) display card (Mandatory). The building official shall require that an energy performance level (EPL)
display card be completed and certified by the builder to be accurate and correct before final approval of the building for occupancy. Florida law
(Section 553.9085, Florida Statues) requires the EPL display card to be included as an addendum to each sales contract for both presold and
nonpresold residential buildings. The EPL display card contains information indicating the energy performance level and efficiencies of components
installed in a dwelling unit. The building official shall verify that the EPL display card completed and signed by the builder accurately reflects the plans
and specifications submitted.to demonstrate compliance for the building. A copy of the EPL display card can be found in Appendix C
❑ R402.4 Air leakage (Mandatory). The building thermal envelope shall be constructed to limit air leakage in accordance with the requirements of
Sections R402.1 through R402.4.4.
0 R402.4-1 Building thermal envelope. The building thermal envelope shall comply with Sections R402.4.1.1 and R402.4.1.2. The
seating methods between dissimilar materials shall allow for differential expansion and contraction.
• R402.4.1.1 Installation. The components of the building thermal envelope as listed in Table R402.4.1.1 shall be installed in
accordance with the. manufacturer's instructions and the criteria listed in Table 402.4.1.1, as applicable to the method of construction.
Where required by the code official, an approved third party shall inspect all components and verify compliance.
• R402.4.1.2 Testing. The building or dwelling unit shall be tested and verified as having an air leakage rate of not exceeding 5 air
changes per hour in Climate Zones 1 and 2, and 3 air changes per hour in Climate Zones 3 through 8. Testing shall be conducted with
a blower door at a pressure of 0.2 inches w.g. (50 Pascals). Where required by the code official. testing shall be conducted by an
approved third party. A written report of the results of the test shall be signed by the party conducting the test and provided to the code
official. Testing shall be performed at any lime after creation of all penetrations of the building thermal envelope.
During testing,
I Exterior windows and doors, fireplace and stove doors shall be closed, but not sealed, beyond the intended w*atherstdpping or
other infiltration control measures;
2. Dampers including exhaust, intake, makeup air, backdraft and flue dampers shall be closed, but not sealed beyond intended
infiltration control measures,
3. Interior doors, if installed at the time of the test, shall be open;
4. Exterior doors for continuous ventilation systems and heat recovery ventilators shall be closed and sealed;
5. Heating and cooling systems, if installed at the time of the test, shall be turned off. and
6 Supply and return registers, if installed at the time of the test, shall be fully open.
O R402.4.2 Fireplaces. New wood -burning fireplaces shalt have tight -fitting flue dampers and outdoor combustion air
O R402.4.3 Fenestration air leakage. Windows, skylights and sliding glass doors shall have an air infiltration rate of no more than 0.3 cfm
per square foot (1 5 Uslm2), and swinging doors no more than 0.5 cfm per square foot (2.6 Us/m2), when tested according to NFRC 400 or
AAh14AN0MA/CSA 10111 S 21A440 by an accredited, independent laboratory and listed and labeled by the manufacturer.
Exception: Site -built windows, skylights and doors
O R402.4.4 Recessed lighting. Recessed luminaires installed in the building thermal envelope shall be sealed to limit air leakage
between conditioned and unconditioned spaces All recessed luminaires shall be iC-rated and labeled as having an air leakage rate not
more than 2.0 cfm (0.944 Us) when tested in accordance with ASTM E 283 at a 1.57 psf (75 Pa) pressure differential. All recessed
luminaires shall be sealed with a gasket or caulk between the housing and the interior wall or ceiling covering.
❑ R403.1.1 Thermostat provision (Mandatory). At least one thermostat shall be provided for each separate heating and cooling system.
❑ R403.1.3 Heat pump supplementary heat (Mandatory). Heat pumps having supplementary electric -resistance heat shall have controls
that, except during defrost, prevent supplemental heat operation when the heat pump compressor can meet the heating load.
❑ R403.2.2 Sealing (Mandatory)AII ducts, air handlers, and filter boxes and building cavities that form the primary air containment
passageways for air distribution, systems shall be considered ducts and plenum chambers, shall be constructed and sealed in accordance
with Section C403.2.7.2 of the Commercial Provisions of this code and shall be shown to meet duct tightness criteria by post -construction
or rough -in testing below.
Duct tightness shall be verified by testing to Section 803 of the RESNET Standards by either an energy rater certified in accordance with Section
553 99, Florida Statutes, or as authorized by Florida Statutes, to be "substantially leak free" by either of the following:
1 Post -construction test: Total leakage shall be less than or equal to 4 cfm (113 Umin) per 100 square feet (9.29 m2) of conditioned floor area
when tested at a pressure differential of 0.1 inches w.g_ (25 Pa) across the entire system, including the manufacturer's air handler enclosure. All
register boots shall be taped or otherwise sealed during the test.
2. Rough -in test: Total leakage shall be less than or equal to 4 cfm (113 Umin) per 100 square feet (9 29 m2) of conditioned floor area when tested
at a pressure differential of 0.1 inches w.g_ (25Pa) across the system, including the manufacturer's air handler enclosure All registers shall be
taped or otherwise sealed during the test. if the air handier is not installed at the time of the test, total leakage shall be less than or equal to 3 cfm
(85 Umin) per 100 square feet (9.29 m2) of conditioned floor area.
Exceptions.
1. The total leakage test is not required for ducts and air handlers located entirety within the building envelope.
2. Duct testing is not mandatory for buildings complying by Section R405 of this code
9/22/2016 11:36 AM EnergyGauge® USA - FlaRes2014 -Section R405.4.1 Cam Page 1 of 3
FORM R405-2014
MANDATORY REQUIREMENTS - (Continued)
❑ R403.2.3 Building Cavities (Mandatory). Building framing cavities shall not be used as ducts or plenums.
• R403.3 Mechanical system piping insulation (Mandatory). Mechanical system piping capable of carrying fluids above 105* F (41'C)
or below 55'F (13'C) shall be insulated to a minimum of R-3.,
R403.3.1 Protection of piping insulation.
❑ R403.4.1 Circulating hot water systems (Mandatory). Circulating hot water systems shall be provided with an automatic or readily
accessible manual switch that can turn off the hot-water circulating pump when the system is not in use.
❑ R403.4.3 Heat traps (Mandatory). Storage water heaters not equipped with integral heat traps and having vertical pipe risers shall have
heat traps installed on both the inlets and outlets. External heat traps shall consist of either a commercially available heat trap or a
downward and upward bend of at least 3 % inches (89 mm) in the hot water distribution line and cold water lire located as close as possible
to the storage tank.
❑ R403.4.4 Water heater efficiencies (Mandatory).
O R403.4.4.1 Storage water heater temperature controls
R403.4.4.1 A Automatic controls. Service water heating systems shall be equipped with automatic temperature controls
capable of adjustment from the lowest to the highest acceptable temperature settings for the intended use. The minimum
temperature setting range shall be from 100'F to 140'F (38'C to 60'C).
R403.4.4.1.2 Shutdown. A separate switch or a clearly marked circuit breaker shall be provided to permit the power supplied
to electric ser-Ace systems to be turned off. A separate valve shall be provided to permit the energy supplied to the main burner(s)
of combustion types of service water heating systems to be turned off.
p R403.4.4.2 Water heating equipment. Water heating equipment installed in residential units shall meet the minimum efficiencies of
Table C404.2 in Chapter 4 of the Florida Building Code. Energy Conservation; Commercial Provisions, for the type of equipment installed.
Equipment used to provide heating functions as part of a combination system shall satisfy all stated requirements for the appropriate water
heating category. Solar water heaters shall met the criteria Section R403.4.4.2.1.
R403.4.4.2.1 Solar water heating systems. Solar systems for domestic hot water production are rated by the annual solar energy
factor of the system. The solar energy factor of a system shall be determined from the Florida Solar Energy Center Directory of
Certified Solar Systems. Sclar collectors shall be tested in accordance with ISO Standard 9806, Test Methods for Solar Collectors,
and SRCC Standard TM-1, Solar Domestic Hot Water System and Component Test Protocol, Collectors in installed solar water
heating systems should meet the following criteria:
1. Be installed with a tilt angle between 10 degrees and 40 degrees of the horizontal; and
2. Be installed at an orientation within 45 degrees of true south.
a R403.5 Mechanical ventilation (Mandatory). The building shall be provided with ventilation that meets the requirements of the
Florida Building Cade, Residential or Florida Building Code, Mechanical, as applicable, or with other approved means of ventilation.
Outdoor air intakes and exhausts shall have automatic or gravity dampers that close when the ventilation system is not operating.
❑ R403.6 Heating and cooling equipment (Mandatory). The following sections are mandatory for cooling and heating equipment.
O R403.6.1 Equipment sizing. Heating and cooling equipment shall be sized in accordance with ACCA Manual S based on the
equipment loads calculated in accordance with ACCA Manual J or other approved heating and cooling calculation methodologies,
based on building loads for the directional orientation of the building. The manufacturer and model number of the outdoor and
indoor units (if split system) shall be submitted along with the sensible and total cooling capacities at the design conditions
described in Section R302.1. This code does not allow designer safety factors, provisions for future expansion or other factors
which affect equipment sizing. System sizing calculations shall not include loads created by local intermittent mechanical ventilation
such as standard kitchen and bathroom exhaust systems.
R403.6.1.1 Cooling equipment capacity. Cooling only equipment shall be selected so that its total capacity is not Tess than the
calculated total load, but not more than 1.15 times greater than the total load calculated according to the procedure selected in
Section 403.6, or the closest available size provided by the manufacturers product lines. The corresponding latent capacity of the
equipment shall not be less than the calculated latent load.
Rage 2 of 3
9/2212016 11:36 AM EnergyGaug&BD USA - F1aRes2014 - Section R405.4 1 Corn
FORM R405-2014
MANDATORY REQUIREMENTS - (Continued)
O R403.6.1.1 Cooling equipment capacity. (continued) The published value for AHRI total capacity is a nominal, rating -test value and
shall not be used for equipment sizing. Manufacture's expanded performance data shall be used to select cooling -only/ equipment. This
selection shall be used to select ccoling-only equipment. This selection shall be based on the outdoor design dry bulb temperature for the
load calculation (or entering water temperature for water -source equipment), the blower cfm provided by the expanded performance data,
the design value for entering wet bulb temperature and the design value for entering dry bulb temperature.
Design values for entering wet bulb and dry bulb temperature shall be for the indoor dry bulb and relative humidity used for the load
calculation and shall be adjusted for return side gains if the return duct(s) is installed in an unconditioned space.
Exceptions:
1. Attached single- and multi -family residential equipment sizing may be selected so that its cooling capacity is less than the
calculated total sensible load but not less than 80 percent of that load.
2. When signed and sealed by a Florida -registered engineer, in attached single- and muiti-family units, the capacity of
equipment may be sized in accordance with good design practice.
O R403.6.1.2 Heating equipment capacity
R403.6.1.2.1 Heat pumps. Heat pumps sizing shall be based on the cooling requirements as calculated according to Section
R403.6.1.1 and the heat pump total cooling capacity shall not be more than 1.15 times greater than the design cooling load.
R403.6.1.2.2 Electric resistance furnaces. Electric resistance furnaces shall be sized within 4 kW of the design
requirements calculated according to the procedure selected in Section R403.6,1
R403.6.1.2.3 Fossil fuel heating equipment. The capacity of fossil fuel heating equipment with natural draft atmospheric burners
shall not be less than the design load calculated in accordancewith Section R403.6.1.
0 R403.6.1.3 Extra capacity required for special occasions. Residences requiring excess cooling or heating'equipment capacity on an
intermittent basis. such as anticipated additional loads caused by major entertainment events, shall have equipment sized or controlled to
prevent continuous space cooling or heating within that space by one or more of the following options-
1 A separate cooling or heating system is utilized to provide cooling or heating to the major entertainment areas.
2 A variable capacity system sized for optimum performance during base lead periods is utilized.
❑ R403.7 Systems serving multiple dwelling units (Mandatory). Systems serving multiple dwelling units shall comply with Sections
C403 and C404 of the Commercial Provisions in lieu of Section R403
❑ R403.8 Snow melt system controls (Mandatory). Snow and ice -melting systems, supplied through energy service to the building. shall
include automatic controls capable of shutting off the system when the pavement temperature is above 55•F, and no precipitation is falling
and an automatic or manual control that will allow shutoff when the outdoor temperature is above 40°F.
❑ R403.9 Swimming pools, inground spas and portable spas (Mandatory). The energy requirements for residential pools and
inground spas shall be as specified in Sections P.403.9.1. through R403 9.3 and in accordance with ANSIlAPSP-15. The energy
requirements for portable spas shall be In accordance with ANSI/APSP-14.
O R403.9.1 Pool and spa heaters. All pool heaters shall be equipped with a readily accessible on -off switch that is mounted
outside the heater to allow shutting off the heater vrithout adjusting the thermostat setting.
R403.9.1.1 Gas and oil -fired pool and spa heaters. All gas- and oil -fired pool and space heaters shall have a minimum
thermal efficiency of 82 percent for heaters manufactured on or after April 16, 2013 when tested in accordance with ANSI Z 21.56.
Pool heaters fired by natural gas or LP gas shall not have continuously burning pilot lights.
R403.9.1.2 Heat pump pool heaters. Heat pump pool heaters shall have a minimum COP of 4.0 when tested in accordance
with AHRI 1160, Table 2, Standard Rating Conditions -Low Air Temperature. A test report from an independent laboratory is
required to verify procedure compliance. Geothermal swimming pool heat pumps are not required to meet this standard
0 R403.9.2 Time switches. Time switches or other control method that can automatically turn off and on heaters and pumps according to a
preset schedule shall be installed on all heaters and pumps. Heaters, pumps and motors that have built in timers shall be deemed in
compliance with this equipment.
Exceptions:
• 1. Where public health standards require 24-hour pump operations.
2. Where pumps are required to operate solar- and waste -heat -recovery pool heating systems.
3. Where pumps are powered exclusively from on -site renewable generation.
O R403.9.3 Covers. Heated swimming pools and inground permanently installed spas shall be equipped with a vapor -retardant cover on or
at the water surface or a liquid cover or other means proven to reduce heat loss.
Exception: Outdoor pools deriving over 70 percent of the energy for heating from site -recovered energy, such as a heat pump or
solar energy source computed over an operating season.
❑ RR404.1 Lighting equipment (Mandatory). A minimum of 75 percent of the lamps in permanently installed lighting fixtures shall be
high -efficacy lamps or a minimum of 75 percent of permanently installed lighting factures shall contain only high efficacy lamps
Exception: Low -voltage lighting shall not be required to utilize high -efficacy lamps.
0 R404.1.1 Lighting equipment (Mandatory). Fuel gas lighting systems shall not have continuously burning pilot lights
❑ R405.2 Performance ONLY. All ducts not entirely inside the building thermal envelope shall be insulated to a minimum of R-6
O R405.2.1 Performance ONLY. Ceilings shall have minimum insulation of R-19. Where single assemby of the exposed deck and beam type or
concrete deck roofs do not have sufficent space, R-10 is allowed.
9122/2016 11:36 AIM EnergyGaugeS USA - FlaRes2014 - Section R405.4.1 Com Page 3 of 3
FORA R405-2014 TABLE 402.4A .1
AIR BARRIER AND INSULATION INSPECTION COMPONENT CRITERIA
Project Name: Express 1672 Aria PSL RIGHT NEW Builder Name:
Street: Permit Office:
City, State, Zip: ST.. LUCIE , FL, Permit Number:
Owner. Express Homes Jurisdictlon;
Design Location: FL, ST_LUCIE_CO_INTL
COMPONENT
CRITERIA
CHECK
Air barrier and thermal barrier
A continuous air barrier shall be installed in the building envelope.
Exterior thermal envelope contains a continuous barrier.
Breaks or joints in the air.barder shall be sealed.
Air -permeable insulation shall not be used as a sealing material.
Ceiling/attic
The air barrier in any dropped ceiling/soffit shall be aligned with the
insulation and any gaps in the air barrier shall be sealed.
Access openings, drop down stairs or knee wall doors to unconditioned
attic spaces shall be sealed.
Comers and headers shall be insulated and the junction of the foundation
Walls
and sill plate shall be sealed.
The junction of the top plate and the top or exterior walls shall be sealed.
Exterior thermal envelope insulation for framed walls shall be installed in
substantial contact and continuous alignment with the air barrier.
Knee walls shall be sealed.
Windows, skylights and doors
The space between window/doorjambs and framing and skylights and
framing shall be sealed.
Rim joists
Rim joists are insulated and include an air barrier.
Floors (including above -garage
Insulation shall be installed to maintain permanent contact with underside
and cantilevered floors)
of subfloor decking.
The air barrier shall be installed at any exposed edge of insulation.
Crawl space walls
Where provided in lieu of floor insulation, insulation shall be permanently
attached to the crawlspace walls.
Exposed earth in unvented crawl spaces shall be covered with a Class I
vapor retarder with overlapping joints taped.
Shafts, penetrations
Duct shafts, utility penetrations, and flue shaft openings to exterior or
unconditioned space shall be sealed.
Narrow cavities
Batts in narrow cavities shall be cut to fit, or narrow cavities shall be filled
by insulation that on installation readily conforms to the available cavity
spaces.
Garage separation
Air sealing shall be provided between the garage and conditioned spaces.
Recessed lighting
Recessed light fixtures installed in the building thermal envelope shall be
air tight, IC rated, and sealed to the drywall.
Plumbing and wiring
Batt insulation shall be cut neatly to fit around wiring and plumbing in
exterior walls, or insulation that on installation readily conforms to available
space shall extend behind piping and wiring.
Shower/tub on exterior wall
Exterior walls adjacent to showers and tubs shall be insulated and the air
barrier installed separating them from the showers and tubs.
Electrical/phone box on
The air barrier shall be installed behind electrical or communication boxes or
air sealed boxes shall be installed.
HVAC register boots
HVAC register boots that penetrate building thermal envelope shall be
sealed to the sub -floor or drywall.
Fireplace
An air barrier shall be installed on fireplace walls. Fireplaces shall have
gasketed doors
9i22l2016 11:36 AM EnergyGauge(b USA - FlaRes2014 Section R405.4.1 Compliant Software rage 1 o' '
FLORIDA ENERGY EFFICIENCY CODE
FOR BUILDING CONSTRUCTION
Envelope Leakage Test Report
Prescriptive and Performance Method
Project Name: Express 1672 Aria PSL RIGHT NEW Builder Name:
Street: Permit Office:
City, State, Zip: ST, LUCIE , FL, Permit Number:
Design Location: FL, ST_LUCIE_CO_INTL Jurisdiction:
Cond. Floor Area:: 1672 sq.ft. Cond. Volume: 14716 cu ft.
Envelope Leakage Test Results
Regression Data:
C:
n: R:
Leakage Characteristics
CFM(50):
Single or Multi Point Test Data
E LA:
HOUSE PRESSURE FLOW:
Eq LA:
ACH.
ACH(50):
SLA:
R402.4.1.2 Testing. The building or dwelling unit shall be tested and verified as having an air leakage rate of not exceeding 5 air changes per hour
in Climate Zones 1 and 2, 3 air changes per hour in Climate Zones 3 through 8. Testing shall be conducted with a blower door at a pressure of 0 2
inches w.g. (50 Pascals). Where required by the code official, testing shall be conducted by an approved third party. A written report of the results of the
test shall be signed by the party conducting the test and provided to the code official. Testing shall be performed at any time after creation of all
penetrations of the building thermal envelope.
During testing:
1. Exterior windows and doors, fireplace and stove doors shall be closed, but not sealed, beyond the intended weatherstripping or other
infiltration control measures;
2, Dampers including exhaust, intake, makeup air, backdraft and flue dampers shall be closed, but not sealed beyond intended infiltration
control measures:
3. Interior doors: if installed at the time of the test, shall be open:
4. Exterior doors for continuous ventilation systems and heat recovery ventilators shall be closed and sealed;
5. Heating and cooling systems, if installed at the time of the test, shall be turned off; and
6. Supply and return registers, if installed at the time of the test, shall be fully open.
I hereby certify that the above envelope leakage
performance results demonstrate compliance
with Florida Energy Code requirements in
accordance with Section R402.4.1.2.
SIGNATURE:
PRINTED NAME:
DATE:
Where required by the code official,
testing shall be conducted by an
approved third party. A written
report of the results of the test shall
be signed by the third party
conducting the test and provided to
the code official.
BUILDING OFFICIAL:
DATE:
011
4k .UD WS
9/22/2013 11:36 AM EnergyGauge(g• USA - FiaRes2014 - Section R405.4.1 Compliant Software Page 1 of 1
p
v
FORM R405-2014 Duct Leakage Test Report Performance Method
FLORIDA ENERGY EFFICIENCY CODE
FOR BUILDING CONSTRUCTION
Form R405 Duct Leakage Test Report
Performance Method
Project Name: Express 1672 Aria PSL RIGHT NEW Builder Name:
Street: Permit Office:
City, State, Zip: ST LUCIE , FL, Permit Number:
Design Location: FL, ST_LUCIE_CO_INTL Jurisdiction:
Duct Test Time: Post Construction
n, IC:t I P-;&;ne Test Results
.I
CFM25 Duct Leakage TValues
Line
System J
Outside Duct Leakage
i I
1
System 1
cfm25(Out)
2
System 2
cfm25(Out)
!
3 1
System 3
i
L cfm25(0ut)
I
4
i
System 4
cfm25(Out)
5
Total House
f Sum lines 14
Duct System
1 Divide by
Leakage
(Total Conditioned Floor Area)
I�
_ (Qn,Out)
{
j
I certify the tested duct leakage to outside, Qn, is
not greater than the proposed duct leakage Qn
specified on Form R405-2014.
SIGNATURE:
PRINTED NAME:
DATE
Duct tightness shall be verified by
testing to Section 803 of the RESNET
Standards by an energy rater certified in
accordance with Section 553.99,
Florida Statutes.
BUILDING OFFICIAL:
DATE:
lk�bO,66 wE
9122/2016 11:36 AM EnergyGaugeG USA - FiaRes2014 - Section R405.4 1 Compliant S Page 1 of 1