No preview available
HomeMy WebLinkAboutEvaluation ReportO V 1 RINIIY fRD� EVAWATION REPORT ICP Adhesives and Sealants, Inc. 12505 NW 44th Street Coral Springs, FL 33065 OCT 2 7 20W Permitting Department St. Lucie. County_ EXTERIOR RESEARCH & DESIGN, LLC. Cert0cate.ofAuthorization #9503 353 CHRISTIAN STREET, UNIT 13 OXFORD, CT 06478 PHONE; (203) 262-9245 FAX: (203) 262-9243 Evaluation Report02768.03;06-R7 FL6332-R7 Date of Issuance: 08/08/2008 Revision: 7: 06/16/2016 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by'Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the a Edition (2014) Florida Building Code sections noted herein. DESCRIPTION: ICP Adhesives Polyset" AH-160 LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This -Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes,, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreementto notify Robert .Nieminen, P.E. if the product changes or the. referenced Quality Assurance documentation changes. Trinity IERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT. The Evaluation Report number preceded, by the words "Trinity I ERD Evaluated" may be displayed in advertising literature. if any portion of the Evaluation Report is.displayed, then it shall be done in its entirety. INSPECTION: Upon. request;, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall beavailablefor inspection at the job site at the request of the Building Official This Evaluation Report consists of pages 1 through 9. Prepared :by: Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DC4ANE1983 The facsimileseal appearing was authorized by Robert Nieminen, A.E. on0611611016. This does not serve as anefectronical[vsigned document. Srgned, seatedhardcopies have been transmitted to the Product ApprovatAdministeatorand, to the named dent CERTIFICATION OF INDEPENDENCE: 1. Exterior Research & Design, LLC. d/b/a Trinity I ERD does not have,.nor does it ntend to acquire or will it acquire, a financial interest in any companymanufacturing at distributing products it evaluates. 2. Exterior Research & Design, LLC. d/b/a Trinity j ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have not will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation. reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither Trinity) ERD .nor Robert. Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. N1n(iERD ROOFING COMPONENT EVALUATION: 1. SCOPE: Product Category: Roofing Sub -Category: Roof Tile Adhesives Compliance Statement: ICP Adhesives Polyset® AH-160, as produced by ICP Adhesives and Sealants, Inc., has demonstrated compliance with the Florida Building Code through testing in accordance with the Standards set forth herein. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: Sections Prove Standard Year 1505.1 External Fire Classification ASTM'E108 2007 1711.2.1 Wind SSTD 11 1997 3. REFERENCES: Entity Examination Reference Date ERD (TST 6049) SSTD 11 P39740.02.12 02/20/2012. ERD(TST 6049) SSTD 11 P39740.11.13-R1 01/02/2015 ICC-ES (EVL2396) 2012 IBC.Compliance ESR-1709 12/01/2014 ITS (TST 1585) ASTM E108 101646522SAT-001_Rev.1 12/23/2014 Miami=Dade (CER 1592) HVHZ compliance 16-0315.01 04/07/2016, PRI (TST 5878) SSTD 11 ECM-001-02-01 09/21/2001 PRI (TST 5878) SSTD 11 PFI-006-02-01 05/09/2005 PRI (TST 5878) SSTD 11 PFI-006-02-02 05/09/2005. PRI (TST 5878) TAS 101 PFI-007-02701 10/11/2005 PRI (TSTS878) SSTD 11 PFI-008=02-04 02/21/2006 PRI (TST 5878) SSTD 11 PFI-009.02-03 02/21/2006 PRI (TST 5878) SSTD 11 TGRI-001-02-03 10/30/2006 PRI (TST 5878) SSTD it TGRI-001-02-03 10/30/2006 PRI (TST 5878) SSTD 11 PFPI-010-02-01 12/07/2006 PRI (TST 5878) SSTD it PFPI-011-02-01 12/07/2006 OR! (TST 5878) SSTD 11 PFPI-012-02-01 12/07/1006 PRI (TST 5878) SSTD 11 PFPI-013-02-01 12/07/2006 PRI (TST5878) SSTD 11 PFPI-014-02-01 12/07/2006 PRI (TST 5878) TAS 101 ECM-003-02-61 06/13/2068 PRI (TST 5878) TAS 101 ECM-004-02-01 06/13/2008 PRI (TST5878) TAS 101 ECM-005-02-01 06/13/2008 PRI (TST 5878) TAS 101 ECM-006-02-01 06/13/2008 PRI (TST 5878) TAS 101 ECM-007-02-01 06/13/2008 PRI (TST 5878) TAS 1.01 ECM-008-02-01 06/13/2008. UL LLC (QUA 9625) Quality Assurance Service Confirmation Exp. 06/05/2018 4. PRODUCr DESCRIPTION: 4.1 ICP Adhesives Polyset® AH-160 is a two -component expanding polyurethane roof tile adhesive that is mixed and dispensed from a dispensing system provided by ICP Adhesives and. Sealants, Inc. The components are available in refillable tanks or disposable cylinders (ICP Adhesives ProPack© 30 & 100). S. LIMITATIONS: 5.1 This is a building code evaluation. Neither TrinitVI ERD nor Robert Nieminen, P.E. are, in anyway, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in the HVHZ. Exterior Research and Design, I.I.C. Evaluation Report 02168.03.06-117 Certificate of Authorization #9503 FL6332-117 Revision 7: 06/16/2016 Page 2 of 9 �TR�IVIN I ERD 5.3 Concrete and clay tiles, having a current Florida Statewide Product Approval or approved on a local -level by the AHJ, adhered using ICP Adhesives Polyset® AH-160, maintain their respective roof fire classifications. Refer to FBC 1505.2, Exception 2. 5.4 ICP Adhesives Polyset® AH-160 can be used with flat, low and high profile tiles or any rigid, discontinuous roof assembly having a current Florida Statewide Product Approval or approved on a.local-level by the AHJ. 5.5 Minimum underlayment shall be per FRSA/TRI April 2012 (0442) or having a current Florida Statewide Product. Approval or approved on a local -level by the AHJ for use with ICP Adhesives Polyset® AH-160. 5.6 Field. tiles using ICP Adhesives Polyset® AH-160 are limited to projects having an Aerodynamic Uplift Moment (MJ, determined in accordance with FBC 1605.5.3 or Tables 2A and 29 of FRSA/TRI April 2012 (04-12), not greater than the following Allowable Overturning Moment values. Refer to Section 10 and ICP Adhesives and Sealants, Inc, published installation instructions for Adhesive Paddy Placement details. TABLE i. eIELD Tiuis IN ICP AoHFSIVFs Poivs� AH-160 ""A LLOWABLE OVERTURNING MOMENT PERFORMANCE DATA .2To1MARGINOFSAFErYAIRE40YAPPUEDFORINDEPENDFIIR(SIN6IEORCgNnNUOUSPADDYJYIACEMENr F ! 4,7D 1 MARGINOFSAFE►YAIREADVAPPNEI iM!kJEROFPENOENT(rWO PADDY) PIACEMENr • _ Tile Adhesive Paddy Placement Allowable Overturning Type Profile Moment.(ft-lbf) Independent;. Single Paddy, Medium (2x7-inch, `30 gram) 60 Concrete Clay Flat Independent; Single Paddy, Large+(2x10-inch, 45 gram) 112 Interdependent; Two Paddy (40-inch on underlayment, 2x4-inch at tile overlap) 54 Independent; Single Paddy, Medium (2x7-inch, ~30 gram) 39 Clay re Low/te Independent; Single Paddy, Large (2x10-inch, -54 gram) 67 Concrete Medium Interdependent; Two Paddy (44-inch on underlayment, W-inch at the overlap) 58 Clay High Independent; Single Paddy, Large (2x10-inch, 45 gram) 134 Independent; Single Paddy, Medium (2x7-inch,1.3U gram) 65 Concrete Clay High Independent; Single Paddy, Large Qx10-inch, -63 gram) 109 Interdependent; Two Paddy (44-inch on underlayment, 2x4-Inch at tile overlap) 40 Clay Barrel 2x10-inchx' 35 gram for pans; 2 @ WO -inch x -17 gram for cap 147 Concrete .Barrel 2x10-inch x -35 gram for pans; 2 @ WO -Inch x -17 gram for cap 107 Clay Cap atop 2x Independent: Continuous Paddy ('34 gram/ft) 135 stringer Concrete Cap atop 2x Independent: Continuous Paddy (, 34 gram/ft) 116 stringer ClayCap atop 2x Interdependent: 105 stringer Head: One (1) #10:x 2%" screw; Overlap:1 x 6 inch ("-10.5 gram) Concrete Cap atop 2x Interdependent: 76 stringer Head: One (1) #10 x 2%:" screw; Overlap:1 x 6 inch (-10.5 gram) 5.6.1 Data in Table 1 relates to installation over a '30/90' underlayment system, as detailed in the FRSA/TRI April 2012 (04-12). Alternate underlayment systems in those having a current Florida Statewide Product, Approval and/or approved on a local -level by the AHJ specifically for use with ICP Adhesives Polysetm AH-160. 5.6.2 Tile roof systems using the types or profiles other than those listed above acquiring acceptance for use with ICP Adhesives Polyset® AH-160 shall be tested :in accordance with SSTD 11 or TAS 101. For the interdependent two -paddy method, an additional 2-to-1 margin above that specified in SSTD 11 or TAS 101 shall be applied in determining the 'allowable overturning moment'. Exterior Research and Design, LLC. Evaluation Report 02768.6106-R7 Cerditate of Authorization 49503 FL6332-117 Revision 7: 06/16/2016 Page 3 of 9 111"iT, RINIIYIERD 5.7 Hip and ridge tiles using ICP Adhesives Polyset° AH-160 are limited to projects having hip/ridge design pressure requirements, determined in accordance with Table 1A of FRSA/TRI April 2012 (04-12), not greater than the following values. Refer to ICP Adhesives and Sealants, Inc. published installation instructions for Adhesive Paddy Placement details. TABLE 2 HIP. i RIDGE TILES IN ICP ADHESIVES POLYSET0AH460 ALLoWAkE UPLIFT RESISTANCE PERFORNIANCE DATA 2ToIMARGIN OFSAFETYAUtEADYAPPUEDFORJNDEPEND£NT(CONTiNuousPADDY)PLAa mENr 4,Tot.MARGINOFWETYALREADYAPPUEDFOR INrFRDEPENDENTPLACEMENT Allowable Tile Substrate Attachment Method Design Pressure (Ps) Clay 2x PT ridge board Independent: Continuous Paddy (^34 gram/ft) 116. Concrete 2x PT ridge board Independent: Continuous Paddy (- 34 gram/ft) 107 Gay 2x PT ridge board Interdependent: Head: One (1) #10 x 2W screw; 90 Overlap: I x 6 inch (-10.5 gram) Concrete 2x PT ridge board Interdependent: Head: One (1) #10 x 2Y" screw; 56 Overlap, 1 x 6 inch (`"10.5 gram) Clay or Hip & Ridge Channel Metal VI-5374): Independent Continuous Paddy (-34 gram/ft). 169 Concrete galvanized only Clay or Trim Lock' (FL5374): aluminum, Independent: Continuous Paddy (^34 gram/ft) i73 Concrete galvanized, Galvalume® or stainless steel Clay or Trim Lock' Plus (FL5374): aluminum, Independent: Continuous Paddy (� 34 gram/ft) 178 Concrete galvanized, GalvalumeOor stainless steel Clay Top Notch (FL8095) Independent: Continuous Paddy (" 32 gram/ft) 125 Concrete Top Notch (FL8095) Independent: Continuous Paddy 32 gram/ft) 146 6. INSTALLATION: 6.1 iCP Adhesives, Polyset° AH-160 and the tile roof assembly shall be installed in accordance with FRSA/TRI April 2012 (04-12) and ICP Adhesives and Sealants, Inc. published installation instructions, subject to the limitations outlined in Section S. 6.2 Hip and ridge boards or hip/ridge metal shall be installed in accordance with the FRSA/TRI April 2012 (04-12). Proprietary hip and ridge metal shall be installed in accordance with the manufacturer's Florida Product Approval. 6.3 Installation shall be performed by applicators who hold a valid Qualified Applicator Card presented by ICP Adhesives and Sealants, Inc. 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 8. MANUFACTURING PLANTS: Tomball, TX 9. QUALITY ASSURANCE ENTITY: UL LLC—QUA9625; (414) 248-6409; Karen.buchmannt@us.ul..com Exterior Research and Design, LLC. Evaluation Report 02768.03.06-R7 Certi/icate of Authorization 4903 FL6332-117 Revision 7: 06/16/2016 Page 4 of 9 TRINITY l ERA 10. PADDY PLACEMENT DETAILS (FROM ICP ADHESIVES AND SEALANTS, INC. PUBLISHED LITERATURE): 10.1 Independent, Medium Paddy: Underlayment ° W ° 7in.y�� �'�2 in. eat t\ optional ° Eave Course 0 o, 10 in. Eave Closure Paddy (Beneath Tile) Flat/Low ProfileTile Nail through plastic cement (when required) Paddy (Beneath Tile) Underlayment `4• v 71 '2In. Battens optional \, I In. Zan. Jr Eave Closure Eave Course Fascia Medium Profile Tile Nail through plastic ce (when required)'Pe Paddy (Beneath Tile) Underlayment , C �- y 7In. Battensoptional o - Eave Course Fascia Weephole 10►n. in. Eaveclosure , Drip edge High Profile Tile Exterior Research and Design; LLC. Evaluation Report 02768.03.06-R7 Certijloste of Authoriratian #9503 F1.6332-117 Revision 7: 06/16/2016 Page S of 9 10.2 Independent.Iarae Paddy: Nail through plastic cement Paddy (Beneath Tile) (when required) Underla ° yment I o optional ° arse 0 �S-I� o, loin. 2, Flat/Low Profile Tile Exterior Research and Design, I.M. eeiti laote ojAuthodzatlori g9503 ERA TRINITY Nail through plastic cement (when required) l0in.x\ 2 in.wide Battens optional s� 10 in. Medium Profile Tile Nall through plasticce (when required) Paddy (Beneath Tile) Underlayment a 2 in.wide Battens / /optional • Eave course r ., Fascia ,F Weephole loin. 2 in. Eave closure Drip edge High Profile Tile Paddy (Beneath Tile) ''-- Eave Closure Fascia Evaluation Report 0276$.03.06-R7 FI.032-R7 Revision 7: 06/16/2016 Page 6 of 9 LO.3 Interdependent. Two Paddy: Nail through plasticcement Paddy (between tiles) (when required) Battens optional ° ° Paddy (under tile) Single paddy on top of the 4x f 4x4in. Single paddy undertil wi Single paddy on underlayment 2 x 4 in. 0 o ` 10in. .� �2in Fascia Eave{losure Flat/Low Profile Tile Nail through plastic cement Single paddy under file (when required) Paddy (between tiles) Battens Paddy (under tile) optlonal Ss� Single paddy on top of tile� x4in. 2x4in. Single paddy an underlayment 1(I n. ' 2in. Eave Closure Eave Course Fascia Medium Profile Tile Nail through plastic ce end Single paddy under tile. (when required) Paddy (between tiles) Battens optional Paddy (under tile) Singlepaddy onunder)ayment "4 x4 in. Single 2x4in paddyon top of the Eavetourse Fascia Weephole 10in.2in. Eaveclosure Drip edge High Profile Tile Exterior Research and Design, UC. Evaluation Report 02768.03:06-R7 Certift ate of Authodlratfon #9503 FL6332-97 Revision 7: 06/16/2016 Page 7 of 9 F VTRINITY ERD 10.4 Two Piece Barrel (Cap & Pan) Tile: ce enough adhesive to achieve 6S to.70 ttact with the pan tile. "COO upalde down. Place adhosivo toIl infromoutsideodgeofcoverUlm cover till: 620 to 21isq.la contact area on Woof corer lira Underlaymenty I (motarshown). Steeppitch Ion of the have course cover tHe.Abut to second course of eave end of pan and cover;ices are flush at eave line. Two Piece Barrel = High Profile.Tile 10.5 Hip and Ridae (independent placement): A toad ofICP Po4NeMAR-160 may be gT*de 9mve the *Id TautUch Wkidge tors, a beed of SCPPoMe Alt-160 nby t& surfs= an boti sides of tie bphidgebomd or gmtimd be opplird dorm the center ofdte hipiidgeboard or gahitczed Waal fratm to ptmide uYattxtbtocker3, frame. Exterior Research and Design, LLC. Evaluation Report 02768.03.06-117 Certificate of Authorization g9503 FL6332-R7 _ Revision 7: 06/16/2016 Page 8 of 9 10.6 Hip and Ridge (interdependent placement]: - END OF EVALUATION REPORT - \I TRINITY I €RD Exterior Research and Design; LLC. Evaluation Report 02768.03.06•R7 t:ertryicate of AuthaNiatfon #9503 FL6332-R7 Revision 7: 06116/2016 Page 9 of 9