HomeMy WebLinkAboutRoofing Felt Installation}
1 � f
RECEIVED AW 0 A 2017
WARRIOR® ROOFING MANUFACTURING
P. 0. BOX 40185 • TUSCALOOSA, AL 35404 • PHONE (205) 5534734 • FAX (205) 553-1755
f
A
193 LEROY ANDERSON ROAD • MONROE, GA 30655 • PHONE (770) 207-0695 • FAX (770) 207.0775
® 323 DEVELOPMENT AVENUE • CHAMBERSBURG, PA 17201 + PHONE (717) 709.0323 • FAX (717) 709-0027
Roofing Felt Installation Recommendations
Be aware that roofing felt should not be walked upon prior to fastening into position.
Proper safety equipment is recommended for all installations. Also, the roof decking
should be clear of debris and moisture prior to installation of the roofing felt.
Roofing felt should be installed from the bottom of the roof in horizontal layers to
increase the water shedding ability of the felt. The initial layer of felt should be installed
to cover the bottom edge of the decking, from edge to edge. Overhang is not required.
Anchor the top corner of the felt after it has been properly positioned and roll the felt out
across the roof. Pay careful attention to roll the felt out smoothly, avoiding wrinkles as
you move across the roof. The top edge of the felt should be fastened no less than every
eight inches. The middle and bottom edge should also be fastened no less than every
eight inches. Fasteners should be applied no less than every eight inches along the eaves.
The next -course of felt should also be aligned with the roof edge and should overlap the
previous course two inches (sometimes referred to as head lap). In the event you get to
the end of a roll prior to getting to the opposite edge of the roof, begin a new roll with a
four inch overlap over the end of the prior roll (sometimes referred to as end lap). The
same fastening pattern used on the middle and bottom of the initial course should be used
for each subsequent course. For the top of each subsequent course, fasten intermittently
to hold the top edge in place until the next course is applied. The fasteners in the bottom
of the next course will hold the top of the previous course securely.
Continue up the roof in this manner. Be sure to firmly fasten the top of the final course if
it terminates at the top edge of the roof. Otherwise, overlap the felt over the ridge and
secure then begin at the bottom of the other side of the ridge and repeat the process.
In valleys, lay a vertical section of roofing felt the length of the valley prior to the
installation of the horizontal runs of roofing felt. If you use more than one section of
roofing felt in a valley, be certain to start at the bottom and overlap_ each subsequent
length a minimum of two inches as you move up the valley to insure proper water
. a 0
shedding7
Y
In the event some wrinkles are created while fastening down a course of felt, slice the
wrinkles and fasten them flat to the deck. Then seal the cuts with waterproofing cement.
' Installation of the primary roof covering (ex. Shingles) is recommended immediately
after felt installation.
1 NOTE: LOCAL BUILDING CODES MAY REQUIRE A DIFFERENT FASTENING
PATTERN AND/OR SPECIFIC FASTENER TYPES THAN RECOMMENDED BY
THESE INSTRUCTIONS. PLEASE CONTACT YOUR LOCAL BUILDING CODE
ADMINISTRATOR FOR THE EXISTENCE OF REGIONALLY SPECIFIC
FASTENING REQUIREMENTS.
tiq `_
ACCREDITED
C
i�wh
6LA, B3
r�
llCP1�IfFD
1 ��11880PATOq';
ti
CONSTRUCTION MATERIALS
TECHNOLOGIES
LABORATORY TEST RESULTS
Report for: Warrior Roofing Manufacturing
3050 Warrior Road
Tuscaloosa, AL 35405
Attention: Steven Crew
Product ID(s): #15
Manufacturer: Warrior Roofing Manufacturing
(Tuscaloosa, AL)
PRI-CMT Project No.: WRMI-007-02-02
Source: Warrior Roofing Manufacturing
Date Received: Jul. 24, 2008
Date(s) Tested: Jul. 29, 2008 —Aug. 8, 2008
Purpose: Evaluate Warrior Roofing Manufacturing's (Tuscaloosa, AL) #15for compliance
with ASTM D 226: Standard Specification for Asphalt -Saturated Organic
Felt Used in' Roofing and Waterproofing.
Test Methods: Testing was completed as described in ASTM D 226-06, -05, and -97a:
Standard Specification for Asphalt -Saturated Organic Felt Used in Roofing and
Waterproofing. Test methods assigned or referenced include ASTM D 70:
Standard Test Method for Density of Semi -Solid Bituminous Materials
(Pycnometer Method); ASTM D 146: Standard Test Methods for Sampling and
Testing Bitumen -Saturated Felts and Woven Fabrics for Roofing and
Waterproofing; and ASTM D 6136: Standard Test Method for Kerosine Number
of Unsaturated (Dry) Felt by Vacuum Method.
Sampling: The sample received from Warrior Manufacturing on July 24, 2008 was a full
factory labeled roll of felt.
WRMI-007-02-02 PRI-CMT Accreditations- AS TL-189• Miami -Dade 11-0429.05• Florida TST5878; Los Angeles TA24819: CRRC
The test results, opinions, or interpretations are based on the material supplied by the client. This report is for the exclusive use of stated
client. No reproduction or facsimile in any form can be made without the client's permission. This report shall not be reproduced except in
full without the written approval of this laboratory. PRI Construction Materials Technologies LLC assumes no responsibility nor makes a
performance or warranty statement for this material or products and processes containing this material in connection with this report.
PRI Construction Materials Technologies LLC 6408 Badger Drive Tampa, FL 33610 Tel; 813-621-5777 Fax: 813.621-5840 e-mail: materialstesting@pricmt.com WebSite: http:thww+.pricmtcom
Warrior Raofing Manufacturing 1
ASTM D 226 for
#15
Page 2 of 3
Results of Testing:
Requirement
•• ••
Type I Type
�`L.e,F�t$lY3
4-....n_Et xiR
•t,1.,�cC,. �.r;e.ri'hnf
jex;edwT '`f�YJ*{fft `�i�"
re
.%i.n'',:,'..._�<, ��"Y� 'G i2Ff�kr,. k
�V„4�.a;.,Y;�bry?:r
JF, {F,,.'.Y/✓
<'l�SA^i"a%'yes"-ii`.....f `x}1'Si
2b+C
y£jyjQ1
1}i.,.
�'y�'�7{'`S
.,,,x�,...,.]:!;...Y.u`".';vi'a f��Y�
fry »" •�i
°Tv�t'S.�� xi
m,..
�Ii
T,p{•.'4S7,fy
�1�.1s?.'.�.,_
W.S�+i}.{ t}y �maZX'"tir�{(I,i.�.,z I
ts�' Xidt�ySF�.��r}y
lsRtg''lr'".1 ht -,� i'5 t,.yi:
�.,� b,
I,4
3a�D ,.
Z , t4N
. ...-t�k...�s..«n'6r F��i1v�.Y"tak�l,e,t5,-j�.f,,..,,�{f...!!"!✓,:�E�x3 rP. t'„i�'�. Ab, ..,:,.i{v;: #i.�§ ..aDil.f,�'f-�rlwRk,Feu".�:es-a'a,.��`Y�zs`�D.�ros..cr, �_. e."
� �
Breaking Strength (Ibf/in-width)
20 specimens; 1" x 6" x thickness;
ASTM D 146
Test @ 73.4±3.6°F; Rate=2in/min
Longitudinal (with fiber grain)
61
> 30
>.40 .
Transverse (across fiber grain)
19
Pliability (Pass/Fail]
10 specimens; 1" x W x thickness;
ASTM D 146
Y2° radius
W radius
Cond. 10-15min in water @ 77±1.8°F;
Test 900 around radius in 2s
Longitudinal (with fiber grain)
Pass
No Failures`
No Failures
Transverse (across fiber grain)
Pass
No Failures
.N:o,Failures '
Loss on Heating (weight %)
2 specimens; 12" x 6" x thickness;
ASTM D 146 2
"s 4
s 4 4 -, .
Test Cond. 221±5°F for 5h±3min
f+4r"
`'`
{ y..�tzk'x?ti
f
n ions,and Masses 4 u past d
a ,rf Si:^ar
tx K ,t11=t
sda.
,��o ..,-, r,d ,�rtcr-G>[t« a., ...,,, -•a_tr .r:. �+� u-�...<F .S�,t..�ws,.e...�.L...1
.��dn�,� k�
,1„
Width of.Roll (in)
ASTM D 146
36
38
Variation, %
0.3
± 0 7,
+ 0.7
Area, min (ft)
ASTM D 146
434
4$2
216
Moisture at Point of Manufacture (%)
ASTM D 146
NT
As Received'
2.2
< 4 3
<x4.1.:�
Net Mass of Saturated Felt (Ib1100ft)
ASTM D 146
14.1
Mass of Saturant (lb/100ft2)
ASTM D 146
7.7
; >— 6 2: - ` -
> 15:0 '
Percent Saturation (%)
ASTM D 226
121
>>_ 1`20 ..
4141, ; _;>.150 ,
Saturation Efficiency (%)
ASTM D 226
70
;>_ 70
Mass of Desaturated Felt (lb/100ft2)
ASTM D 146
6-.4
Ash (%)
ASTM D 146
5.3
<<�10 0"
Continued on Following Page
WRMI 007 02 02 PRI-CMT Accreditations IAS TL-189; Miami -Dade 11-0429.05: Florida TST5878: Los Angeles TA24819; CRRC
The test results, opinions, or interpretations are based on the material supplied by the client. This. report is for the exclusive use. of stated
client. No reproduction or facsimile in any form can be made without the client's permission. This report shall not be reproduced except in
full without the written approval of this laboratory. PRI Construction Materials Technologies LLC assumes no responsibility nor makes a
performance or warranty statement for this material or products and processes containing this material in connection with this report.
PRI Construction Materials Technologies LLC 6406 Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: maledalstesting@pdcmt.com WebSite: hltp:lhNww.pricmtcom
Warrior Roofing Manufacturing -
ASTM D 226 for
#15
Page 3 of 3
Requirerhant
Property•• Result
Type I Type 11
Perforated Felt (ins) ASTM D 226 NA0
Average Venting Area (%}
ASTM D 226
NA
:�-{ ,� t .:�..C. s � _,i R) i'•,dr:+J: �� <?:mi-�.;� r� � ,:t . � � �i: �
'�".. �s' r Pi s
� u � �-s � „'�tr. n: x �. �,'�c„,.kt �t., ;
�x �^j�tdr�"',�gjyyA.A'��E��§��9s�ss`tf4`M,�Y�'G
% � �i ��
� ? ,1.. s�i� ,�
...t�'�tvi�`��v�
�s (, -s s�$•
r r
i�+v°�. �x.,?`�"Y ''i�{F :.u��'�y�'�"`a��+;',
- , � ��r;` r r � �'�s
'�� �af'£r �'.� �`,' . a�.•
'����p''� ,�:"F��F'�'�,.�
� "� � %r P { v
n k�ca ,,�rr`& .w°t...
Unrolling @ 50°F and 140°F (Pass/Fai/J
ASTM D 226
Pass
No:Damage ":
No°Damage
Note(s): 1- Moisture (As Received) was utilized in lieu of Moisture at Point of Manufacture;
NT- Not Tested;
NA- Not Applicable
Statement of Compliance: The product tested is compliant with ASTM D 226: Standard Specification for
Asphalt -Saturated Organic Felt Used in Roofing and WatqWA®>s
Toe I (No. 15).
Signed: Signed:
Brad Grzybqkski
Managing Director
Date: 11 of j f Date:
Report Issue History:
Duc 19gbyen • W
Florida Registered'rQfessio8*X`? +nefJF 11 h
P.E. Nur;�Q- 650�4
Issue # Date Pages I Revision Description (if applicable)
Original 07/24/2008 3 NA
Revisionl 11/09/2011 3 Revised to exclude reference to Florida Building Code 2007.
Reissued.
END OF REPORT
WRMI-007-02-02 PRI-CMT Accreditations: IAS TL-189: Miami -Dade 11-0429.05; Florida TST5878; Los Angeles TA24819; CRRC
The test results, opinions, or interpretations are based on the material supplied by the client. This report is for the exclusive use of stated
client. No reproduction or facsimile in any form can be made without the client's permission. This report shall not be reproduced except in
full without the written approval of this laboratory. PRI Construction Materials Technologies LLC assumes no responsibility nor makes a
performance or warranty statement for this material or products and processes containing this material in connection with this report.
PRI Construction Materials Technologies LLC 6408 Badger Drive Tampa, FL 33610 Tel: 818-621-5777 Fax: 813-621-5840 e-mail: materialstesting@pricmt•com WebSite: http:/Mm..pricmt.com
aces��tT�o _
a
-ONSTRUCTION MATERIALS
LAMM T E C H N 0 L 0 0 1 E
Y�
i Cc
LABORATORY TEST RESULTS
ACCRED,Y(D
j EA80RATi1RY
I I
Report for: Warrior Roofing Manufacturing Attention: Steven Crew
3050 Warrior Road
Tuscaloosa, AL 35405
Product ID(s):' #30
Manufacturer: Warrior Roofing Manufacturing
(Tuscaloosa; AL)
PRI-CMT Project No.: WRMI-008-02-02
Source: Warrior Roofing Manufacturing
Date Received: Jul. 24, 2008
Date(s) Tested: Jul. 29, 2008 —Aug. 8, 2008
Purpose: Evaluate Warrior Roofing Manufacturing's (Tuscaloosa, AL) #30 for compliance
with ASTM D 226: Standard Specification for Asphalt -Saturated Organic
Felt Used in Roofing and Waterproofing.
Test Methods: Testing was completed as described in ASTM D 226-06, -05, and -97a:
Standard Specification for Asphalt -Saturated Organic Felt Used in Roofing and
Waterproofing. Test methods assigned or referenced include ASTM D 70:
Standard Test Method for Density of Semi -Solid Bituminous Materials
(Pycnometer Method); ASTM D 1.46: Standard Test Methods for Sampling and
Testing Bitumen -Saturated Felts and Woven Fabrics for Roofing and
Waterproofing; and ASTM D 6136: Standard Test Method for Kerosine Number
of Unsaturated (Dry) Felt by Vacuum Method.
Sampling: The sample received from Warrior Manufacturing'on July 24, 2008 was a full
factory labeled roll of felt.
The test°results, opinions, or interpretations are based on the material supplied bythe client This report:is forthe exclusive use o stated
client. No reproduction or facsimile in any form can be made without the client's permission. This report shall not be reproduced except in
full without the written approval of this laboratory. PRI Construction Materials Technologies LLC assumes no responsibility nor makes a
performance or warranty statement for this material or products and processes containing this material in connection with this report.
PRI Construction Materials Technologies LLC 6408 Badger Drive Tampa, FL 33610 Tel: 813.621-5777 Fax:813-621-5840 e-mail: materialstesfing@pricmi.com Web8ite: http://www.pricmtcom
Warrior hoofing Manufacturing
ASTM D 226 for
#30
Page 2 of 3
Results of Testina:
•
.. ••
Type I Type
{I f ,f x(r` £ W '21 '�YgE kS5S£.✓t wlY.f y �xR ,rd l _YYh V7kh tt iYj ,Z 5 5l fi, J 4 t4 d1 YeX $dU't" F'{' C} t Y SgtZfy' f Si9 j zf'at tfj}p4f
f � r � J h^R Y 1 �Y� i4'`.-v� � }tfr
3� Jti 4 �f8V5 A9$1 E$ ���t�it 4�
AtYt.
F`zV{ $d '✓fhi� 1N
43Sz Pr 1++'� S Y1l� Sd 1 rf
.;
FF�� Ph. s�cal Re wrements S£
tv' `w ��....
Lti
T $ Ff%,:��.. f.,. .. ,J .6., f z�tt.. i;I}3f4.. 3'.A$�x-:k'�`ih, f..�bd`R,>S i4�k�F�.i.,,Sdi�f S�z'{ShCf.U.�t�J}-: F,f4a.11T'+ifi%M„5..�t'q�i. �j.i�S�Sij,Y_'�}sF'i �g✓l ..,Yf: dA
Breaking Strength (Ibf/in-width)
20 specimens; 1" x 6"x thickness;,
ASTM D 146
Cond. 2h @ 73.4±3.60F & 50±5%RH;
Test @ 73.4±3.6°F; Rate=2in/min
Longitudinal (with fiber grain)
66
Transverse (across fiber grain)
30
> 15
„
Pliability [Pass/Fail]
10 specimens; 1" x 8" x thickness;
'%"
ASTM D 146
%" radius
radius
Cond. 10-15min in water @ 77±1.8°F;
Test 900 around radius in 2s
Longitudinal (with fiber grain)
Pass
No Failures:
NoFailures;
Transverse (across fiber grain)
Pass
No. Fall'wres -
`, NO.Failures
Loss on Heating (weight %)
2 specimens; 12" x 6" x thickness;
ASTM D 146
2
Test Cond. 221±5°F for 5h±3min
�. !e. }',(t 5 S�{�k t{" k'.�
}cc.,, ,f� ,1 �M�,( Y�L��i*'� 3;
g.,. '$,2Fj r?2 fnf ('kn/+y,t
i )�'C SI J�; �'Y� }101x a4�
y+qt fitnrR '.tFssra'`V Y R',y1',.t R `1'� t� 'I
ktlNF"F .4 ,P �'V 5$95 �t5Y4^t` y{fi {taFy t���$� V
t.,� yA e' 1 ^T"�x CSSt /, �,�:,:;•
��
4117it>ienSlons�FandNfaSSes
..
Width of Roll (in)
ASTM D 146
36
Variation, %
0.3
4 0 7 ;
±:01
Area, min (ft2)
ASTM D 146
216
432 :
216: ,
Moisture at Point of Manufacture (%)
ASTM D 146
NT
:,< 43
As Received'
3.0
- " <, 4 3
s 41'
Net Mass of Saturated Felt (lb/100ft2)
ASTM D 146
27.3
.> 11 5;;~
>:26
Mass of Saturant (lb/100ft2)
ASTM D 146
15.9
: > 6 2
> 15.0 '.
Percent Saturation (%)
ASTM D 226
150
° > 120'`. -
> -150
Saturation Efficiency (%)
ASTM D 226
NA
> 70
Mass of Desaturated Felt (lb/100ft)
ASTM D 146
10.6
�'> 5 2
z,10-,�6
Ash (%)
ASTM D 146
4.0a
Continued on
The test results, opinions, or interpretations are based on the material supplied by the client. This report is for the exclusive use of stated
client. No reproduction or facsimile in any form can be made without the client's permission. This report shall not be reproduced except in
full without the written approval of this laboratory. PRI Construction Materials Technologies LLC assumes no responsibility nor makes a
performance or warranty statement for this material or products and processes containing this material in connection with this report.
PRI Construction Materials Technologies LLC 6408 Badger Drive Tampa, FL 33610 Tel: 813-621-5777 Fax: 813-621-5840 e-mail: mate6alstesting@pricmt.com Web8ite;http://VAVW.pricmt.com
i
s
Warrior Roofing Manufacturing
ASTM D 226 for
#30
Page 3 of 3
Perforated Felt (in2) ASTM D 226 NA <0 05
Average Venting Area (%) ASTM D 226 NA > 0
Unrolling @ 50OF and 140OF (Pass/Fail] ASTM D 226 I Pass I No, Damage I No+Damage .
Note(s): 1- Moisture (As Received) was utilized in lieu of Moisture at Point of Manufacture;
NT- Not Tested;
NA- Not Applicable
Statement of Compliance: The product tested is compliant with ASTM D 226: Standard Specification for
Asphalt -Saturated Organic Felt Used in Roofing and Waterproofing as
Type II (No. 30).
,d
Signed: -,i
Brad rzybow i
Managing Director
Date: fA C1/
Report Issue History:
Signed:
Date:
ial Enwneer e
mm
iTATE OF Wes.
®®P
0000
11881111900
Issue # Date Pages I Revision Description (if applicable)
Original 07/24/2008 3 NA
Revisionl 11/09/2011 3 Revised to exclude reference to Florida Building Code 2007.
Reissued.
END OF REPORT
WRMI-008-02-02 PRI-CMT Accreditations' IAS TL-189' Miami -Dade 11-0429.05' Florida TST5878; Los Angeles TA24819; CRRG
The test results, opinions, or interpretations are based on the material supplied by the client. This report is for the exclusive use of stated
client. No reproduction or facsimile in any form can be made without the client's permission. This report shall not be reproduced except in
full without the written approval of this laboratory. PRI Construction Materials Technologies LLC assumes no responsibility nor makes a
performance or warranty statement for this material or products and processes containing this material in connection with this report.
PRI ConsUuction Materials Technologies LLC 6408 Badger Drive Tampa, FL 33610 Tel:813-621-5777 Fax: 813-621-5840 e-mail: materialstesting@pricmLcom WebSite: http://www.pricmt.com