HomeMy WebLinkAboutNotice Of Product CertificationNOTICE OF PRODUCT CERTIFICATION
w
1f
ECEIVED AUG 0 J 2017
CERTIFICATION NO:
DATE:
CERTIFICATION PROGRAM:
COMPANY:
CODE:
REVISION DATE:
NI011567.02-R2
05/23/2013
Structural
JELD-WEN
1822-1
01/13/2017
To verify that the "Notice of Product Certification" is valid, please visit www.NAMICertification.com to assure that the
product is active and currently listed. This certification represents product conformity to the applicable specification and
that certification criteria has been satisfied. A NAMI approved certification label must be applied to the product to claim
certification status. Please review and advise NAMI if any corrections are required to this document.
COMPANY NAME AND ADDRESS
PRODUCT DESCRIPTION
JELD-WEN
"Premium Atlantic Vinyl Single Hung"
3737 Lakeport Boulevard
Impact Rated Vinyl Single Hung Window
Klamath Falls, OR 97601
(Fin & Flange Installation)
Configuration: O/X
Glazing: IG-1/8" Annealed Glass/Laminate-
1/8" Annealed Glass/0.090" SentryGlas® Plus Interlayer by
DuPont/l/8" Annealed Glass or IG-1/8" Annealed
Glass/Laminate-1/8" Annealed Glass/0.090" PVB by
DuPont/l/8" Annealed Glass
Frame: W-1324mm(52.13") H-1905mm(75")
Sash: W-1254mm(49.38") H-946mm(37.25")
SPECIFICATION
.PRODUCT RATING
TAS 201/202/203-94
Design Pressure: +50/-60 psf
Large Missile Impact Rated
Product Tested By: National Certified Testing Laboratories
Report No: NCTL-210-3874-1
Expiration Date: April 30, 2025
Administrator's Signature:
NATIONAL ACCREDITATION AND
MANAGEMENT INSTITUTE, INC.
4794 George Washington Memorial Highway
Hayes, VA 23072
Tel: (804) 684-5124
Fax: (804) 684-5122
FRDY
CDRIE113
A Ym3MN
T�
HN
YmSPAN4
WBODW WIDTH (52 Ile MAX)
TYPICAL ELEVATION WITH FASTENER SPACING
o.c.
�IN
t' YA1I.
FRDY
Installation Notes:
1. Seal flange/frame to substrate.
2. Use #10 PH or greater fastener though the nail fin with sufficient length to penetrate a minimum of 1
1/2" into the wood framing. For 2X wood frame substrate (min. S.G. = 0.42).
3. Host structure (wood buck, masonry, steel) to be designed and anchored to properly transfer all loads
to the structure. The host structure is the responsibility of the architect or engineer of record for the
project of installation.
Digitally signed by Hermes F. Norero, P.E.
Reason: I am approving this document
Date: 2014.09.1916:25:32-04'00'
This schedule addresses only the fasteners required to anchor the /
window to achieve the rated design pressure up to the size limitations
111—/2' MIEN. EMBEDMENT
9I / �2X WOOD FRAME
MIN. DISTANCE
FOR EDGE: 3/4"
GLAZING DETAIL
FRAME SECTION (TYP)
VERTICAL SECTION
WTE: C"dkW—n WOM Fimge d Wood 0, }
MIN. DISTANCE
FOR EDGE: 3/4'
WOOD FRAME
NAIL FIN INSTALLATION
MIN. DISTANCE
FOR EDGE: 3/4"
2X WOOD
i
FRAME
i
1/4" MAX
i
SHIM SPACE
11/2" MIN.
EMBEDMENT
I
1
JAMB SECTION (TYP)
HORIZONTAL SECTION
NOTE: Coelk bet— Nailing Flmge A Wand Opening.
PREMIUM ATLANTIC VINYL SH WINDOW
Max Frame DP RATING IMPACT
52 1/8 x 75 +50/-60 YES
LARGE MISSILE IMPACT
General Notes:
1. The product shown herein is designed, tested -and manufactured to comply with the wind load criteria
of the adopted International Building Code(IBC), the International Residential Code(IRC), the Florida
Building Code (FBC) including HVHZ and the industry requirement for the stated conditions.
2. All glazing shall conform to ASTM E1300.
3. At minimum, glazing is 3mm annealed -11 mm airspace - 3mm annealed - 2mm PVB Intedayer by
DuPont - 3mm annealed.
4. Use structural or composite shims where required.
noted. It is not intended as a guide to the installation process and does
�� ��
PRWECT ENGINEER:
DATE:
not address he sealing consideration that may arise in different wall
�� e• �` ��
` ••••• •• "
�' ��
--
08/13/2014
Lakeport Blvd
conditions. For the complete installation procedure, see the instructions
��; �,�
DRAWN BY:
SCAIP:
Klamath Falls, OR. 976oi
JELDVEN th F
packaged with the window or go to
:
~ 7
D. Vezo
NTS
Phone: (541) 882-3451
CHECKED BY:
J. KED BY:
tola
TITLE:
www.jeld-wen.com/resourcesAnstallafion.
_ * *
0: =
�:
Premium Atlantic Vinyl Impact Single Hung Window
APPROVED BY:
DISCLAIMER:
�J (V
This drawing and its contents are confidential and are not to be
. O,n '•. C Dp' •' �:
���
P�Rr�P�oE�g
U
reproduced or copied in whole or in part or used or disclosed to others
P.E. N
IDENTIFIER No.
NCTL210-3874-
PLANT NAME AND LOCATION:
-FBC
CAD DWG. No.:
REV:
00
SHEET
IOF3
except as authorized by JELD WEN Inc.
aea D to 33e
n 111
M
MAL
HERS
1EA• o.C.
MAX. TM
JAN11
FROM
CORNERS
--WINDOW N701H (52 I/V MAX.)
TYPICAL ELEVATION WITH FASTENER SPACING
Installation Notes:
1. Seal flange/frame to substrate.
2. Use 3/16" ITW Tapcon or equivalent fasteners through frame with sufficient length to penetrate a
minimum of 11/4" into concrete or masonry at each location with a 21/2" min from edge distance. For
concrete (min. Pc = 3000psi) or masonry substrate (CMU shall adhere to ASTM C90).
3. Host structure (wood buck, masonry, steel) to be designed and anchored to properly transfer all loads
to the structure. The host structure is the responsibility of the architect or engineer of record for the
project of installation.
This schedule addresses only the fasteners required to anchor the
window to achieve the rated design pressure up to the size limitations
noted. It is not intended as a guide to the installation process and does
not address he sealing consideration that may arise in different wall
conditions. For the complete installation procedure, see the instructions
.;
packaged with the window or go to
www.jeld-wen.com/resourcesAnstallation.
DISCLAIMER:
This drawing and its contents are confidential and are not to be
reproduced or copied in whole or in part or used or disclosed to others
except as authorized by JELD-WEN Inc.
see El
MM DISTANCE
FOR EDGE: 21/7
2
Q4'.
MAsomy
BLOCK
a
v 3
11/4' MM
EMBEDMENT
—1/4' MAX
S1OM SPACE
zmm
zmm
3mm 3mm
6LAZING DETAIL
FRAME SECTION (TYP)
VERTICAL SECTION
SOM SPACE
Jr24 IV4MMEMB
MENT
TMASONRY
A BLACK
MASONRY INSTALLATION
11/4' MIN.
EMBEDMENT
1/4' MAX
a 3 SHIM SPACE
MIN. DISTANCE V V
FOR ED6E: 21/2' Q 'l
MASONRY
BLOCK 01
JAMB SECTION (TYP)
HORIZONTAL SECTION
PREMIUM ATLANTIC VINYL SH WINDOW
Max Frame I DP RATING IMPACT
52 1/8 x 75 1 +50/-60 1 YES
��-MREWE:2NCE 1/T FOR EDGE: LARGE MISSILE IMPACT
General Notes:
1. The product shown herein is designed, tested and manufactured to comply with the wind load criteria
of the adopted International Building Code(IBC), the International Residential Code(IRC), the Florida
Building Code (FBC) including HVHZ and the industry requirement for the stated conditions.
2. All glazing shall conform to ASTM El300.
3. At minimum, glazing is 3mm annealed -11 mm airspace - 3mm annealed - 2mm PVB Interlayer by
DuPont - 3mm annealed.
4. Use structural or composite shims where required.
�tj�`�•••• v
�j,
PROJECT ENGINEER:
r
• �'� •
- p�
D Vezo
7
_ -
CHECKED BY;
J. Kantola
T T
fY
APPROVED BY:
AA .
xox�ne�i� .
6 7qq7 1^
P.E. No
a
IDENTIFIER No.
NCTL210-3874-
to 338
a
DATE`
08/13/2014 jEL]WWEN 3737 Lakeport Blvd
5�,8; Klamath Falls, Blvd
NTS I Phone: (541) 882-3451
Premium Atlantic Vinyl Impact Single Hung Window
AND LOCATION: I CAD DWG. No.: I REV. 00 I SHEET
20F3
C
14" OR. MAX.
1NRU JAMB
WINDOW W811N (82 1/8' MAXI
TYPICAL ELEVATION WITH FASTENER SPACING
MAX.
4.8' MAX.
FROM
CORNERS
Installation Notes:
1. Seal flange/frame to substrate.
2. For anchoring into metal framing use #8 TEK Self Tapping screws with sufficient length to achieve a
minimum embedment of three threads past the frame thickness. Steel substrate min.18ga., fy = 33 ksi.
3. Host structure (wood buck, masonry, steel) to be designed and anchored to properly transfer all loads
to the structure. The host structure is the responsibility of the architect or engineer of record for the
project of installation.
This schedule addresses only the fasteners required to anchor the
window to achieve the rated design pressure up to the size limitations
noted. It is not intended as a guide to the installation process and does
not address he sealing consideration that may arise in different wall
conditions. For the complete installation procedure, see the instructions
packaged with the window or go to
www.jeld-wen.com/resources/installation.
DISCLAIMER:
This drawing and its contents are confidential and are not to be
reproduced or copied in whole or in part or used or disclosed to others
except as authorized by JELD-WEN Inc.
, `Q t 17 A,
MIN. DISTANCE
FOR EDGE: 1/2°
4j./4"
in. embedment
f three threads
st frame
18 gauge min
Steel Stud
MAX
SPACE
zmm
2mm
3mm 3mm
BITE
GLAZING DETAIL
FRAME SECTION (TYP)
VERTICAL SECTION
WMC e.b. Wn FWq aWm ow—i
op— 1/45 MAX
SHIM SPACE
18 gauge min
Steel Stud
of three threads
past
MIN. DIS DISTANCE
FOR EDGE: 1/2°
I
i
I
38 gauge min -
Steel Stud
I
i
MIN. DISTANCE C
FOR EDGE: 1/2"
I
Min. embedment
of three threads
Past frame
STEEL INSTALLATION
1/4" MAX
SHIM SPACE
JAMB SECTION (TYP)
HORIZONTAL SECTION
PREMIUM ATLANTIC VINYL 5H WINDOW
Max Frame DP RATING IMPACT
52 1/8 x 75 +50/-60 1 YE5
LARGE MI55ILE IMPACT
General Notes:
1. The product shown herein is designed, tested and manufactured to comply with the wind load criteria
of the adopted International Building Code(IBC), the International Residential Code(IRC), the Florida
Building Code (FBC) including HVHZ and the industry requirement for the stated conditions.
2. All glazing shall conform to ASTM E1300.
3. At minimum, glazing is 3mm annealed -11 mm airspace - 3mm annealed - 2mm PVB Intedayer by
DuPont - 3mm annealed.
4. Use structural or composite shims where required.
PROJECT ENGINEER: DATE: 08/3737 Lakeport Blvd
-- 13/2014 .
DRAWN 8Y: SCALE: JELWWENKJamath Falls, OR. 97601
D. Vezo NTS Phone: (541) 882-3451
J.
BY: - I Premium Atlantic Vinyl Impact Single Hung Window
AND LOCATION:
00 ��3 OF 3
Fla
BUILDING DROPS
A Perfect Solution in Every Drop
Certificate of Authorization: 29578
JELD-WEN, Inc.
398 E. Dania Beach Blvd.
Suite 338
Dania Beach, FL 33004
954.399.8478 PH
954.744.4738 FX
contact@buildingdrops.com
Premium Atlantic Vinyl Single Hung - Impact
for
Florida Product Approval
Current Florida Building Code
Method: 1— A (Certificate)
Category: Windows
Sub — Category: Single Hung
Product: Premium Atlantic Vinyl Single Hung - Impact
Material: PVC
Product Dimensions: 52-118" x 75" (OIX)
Prepared For:
r JELD-WEN,1nc.
3737 Lakeport Blvd.
Klamath Falls, OR 97601
Prepared by:
Hermes F. Norero, P.E.
Florida Professional Engineer # 73778 Q-�,.•• " • ••�`���i
Date:08/11/2014 �'ZZ : p
7 _
Contents: _ 7k
Evaluation Report Pages 1— 4 'b T T x
:per-�•• �0 DP•• ���
Digitally signed by Hermes F. Norero, P.&
1
Reason: I am approving this document ''��ON�
Date: 2014.09.19 16:31:16 -04 00
Hermes F. Norero, P.E.
Florida No. 73778
ral
Manufacturer:
BUILDING DROPS
A Perfect Solution in Every Drop
Certificate of Authorization: 29578
JELD-WEN, Inc.
Product Category:
Product Sub -Category:
Compliance Method:
Product Name:
Windows
Single Hung
State Product Approval Method (1)(a)
Premium Atlantic Vinyl Single Hung - Impact
52-1/8" x 75" (O/X)
Date: 08/11/2014
Report No: 3091
Scope: This is a Product Evaluation Report issued by Hermes F. Norero, P.E. (FL # 73778) for JELD-WEN, Inc.
based on Method 1a of the State of Florida Product Approval, Department of Business and
Professional Regulation - Florida Building Commission.
Limits of Use:
Hermes F. Norero, P.E. does not have nor will acquire financial interest in the company
manufacturing or distributing the product or in any other entity involved in the approval process of
the product named herein.
This product has been evaluated for use in locations adhering to the current Florida Building Code.
See Installation Instructions NCTL210-3874-1-FBC, signed and sealed by Hermes F. Norero, P.E. (FL #
73778) for specific use parameters.
1. This product has been evaluated and is in compliance with the current Florida Building Code,
including the "High Velocity Hurricane Zone" (HVHZ).
2. Product anchors shall be as listed and spaced as shown on details. Anchor embedment into
substrate material shall be beyond wall dressing or stucco.
3. When used in areas requiring wind borne debris protection this product complies with
Section 1609.1.2 of the current Florida Building Code and does not require an impact
resistant covering.
4. Site conditions that deviate from the details of drawing NCTL210-3874-1-FBC require further
engineering analysis by a licensed engineer or registered architect.
5. See Installation Instructions NCTL210-3874-1-FBC for size and design pressure. limitations.
Hermes F. Norero, P.E.
Florida No. 73778
Page 2 of 4
BUILDING DROPS Date: 0014
Report Noo:: 3091
A Perfect Solution in Every Drop
Certificate of Authorization: 29578
Quality Assurance: The manufacturer has demonstrated compliance of products in accordance with the
Florida Building Code for manufacturing under a quality assurance program audited
by an approved quality assurance entity through National Accreditation and
Management Institute (FBC Organization #: QUA 1789)
Performance Standards: The product described herein has been tested per:
• TAS 201-94
• TAS 202-94
• TAS 203-94
Referenced Data: 1. Product Testing performed by National Certified Testing Laboratories NW
(FBC Organization # TST9341)
Report #: NCTL-210-3874-1, Report Date: 4/18/2013
2. Certification Agency
National Accreditation and Management Institute
(FBC Organization #: CER 1773)
3. Material Certification
Miami Dade RER —Product Control Section NOA
E.I. DuPont De Nemours & Co., Inc.: PVB Interlayer
4. Material Certification
Miami Dade RER — Product Control Section NOA
Quanex Building Products: PVC Extrusions
1.
Hermes F. Norero, P.E.
Florida No. 73778
Page 3 of 4
• Date: 0o: 30014
BUILDING DROPS
Report No: 91
A Perfect Solution in Every Drop
Certificate of Authorization: 29578
Through Frame Installation: 1. Approved anchor types and substrates areas follows:
A. For concrete (Min. fc = 3000 psi) or masonry substrate (Min. fc = 1500 psi) where one
by (1X), non-structural, wood bucking is employed, use (1) 3/16" diameter ITW Tapcon
type concrete screw anchors per location of sufficient length to achieve minimum
embedment of 1.25" into concrete.or masonry.
B. For concrete (Min. fc = 3000 psi) or masonry substrate (Min. fc = 1500 psi) where wood
bucking is NOT employed, use (1) 3/16" diameter ITW Tapcon type concrete screw
anchors per location of sufficient length to achieve minimum embedment of 1.25" into
concrete or masonry.
C. For steel substrate, use (1) #8 Tek Screw type steel frame (min. 18ga.) anchors per
location of sufficient length to achieve minimum three threads of penetration beyond
steel structure.
Nail Fin Installation (Where applicable):
A. For wood substrates (Min. S.G. = 0.42) use (1) #10 Wood Screw type installation anchors
per location of sufficient length to achieve a minimum embedment of 1.50" into the
wood substrate.
Refer to Installation Instructions (NCTL210-3874-1-FBC) for anchor spacing and more details of the
installation requirements.
Design Pressure:
Design Pressure
Positive 50 PSF
• Negative 60 PSF
Hermes F. Norero, P.E.
Florida No. 73778
Page 4 of 4
BUILDING DROPS
A Perfect Solution in Every Drop
Certificate of Authorization: 29578
Product Ev.1 " : c.11 i a1 9 Report
Of
JELD-WEN, Inc.
398 E. Dania Beach Blvd.
Suite 338
Dania Beach, FL 33004
954.399.8478 PH
954.744.4738 FX
contact@buildingdrops.com
Premium Atlantic Vinyl Single Hung - Impact
fog'
Florida Product Approval
Current Florida Building Code
Method: 1— A (Certificate)
Category: Windows
Sub — Category: Single Hung
Product: Premium Atlantic Vinyl Single Hung - Impact
Material: PVC
Product Dimensions: 52418"x 75" (OIX)
Prepared For:
JFLD-WEN, Inc.
3737 Lakeport Bled.
Klamath Falls, OR 97601
Prepared by: ```I%J11 i i rrri,,�i
Hermes F. Norero, P.E.�.� ES F.
Florida Professional Engineer # 73778 Q-� .•• " • �` ��i
Date: 08/11/2014 ��;'
7
Contents:
Evaluation Report Pages 1— 4 'fl T T CC
Digitally signed by Hermes F. Norero, P. IFS ••'•••••••''•• C�N��`�
Reason: I am approving this document i"�'S,�N;
Date: 2014.09.19 16:31:16-04'00'
Hermes F. Norero, P.E.
Florida No. 73778
BUILDING DROPS
�' A Perfect Solution in Every Drop
Certificate of Authorization: 29578
Manufacturer: JELD-WEN, Inc.
Product Category: Windows
Product Sub -Category: Single Hung
Date: 08/11/2014
Report No: 3091
Compliance Method: State Product Approval Method (1)(a)
Product Name: Premium Atlantic Vinyl Single Hung - Impact
52-1/8" x 75" (O/X)
Scope: This is a Product Evaluation Report issued by Hermes F. Norero, P.E. (FL # 73778) for JELD-WEN, Inc.
based on Method 1a of the State of Florida Product Approval, Department of Business and
Professional Regulation - Florida Building Commission.
Limits of Use:
Hermes F. Norero, P.E. does not have nor will acquire financial interest in the company
manufacturing or distributing the product or in any other entity involved in the approval process of
the product named herein.
This product has been evaluated for use in locations adhering to the current Florida Building Code.
See Installation Instructions NCTL210-3874-1-FBC, signed and sealed by Hermes F. Norero, P.E. (FL#
73778) for specific use parameters.
1. This product has been evaluated and is in compliance with the current Florida Building Code,
including the "High Velocity Hurricane Zone" (HVHZ).
2. Product anchors shall be as listed and spaced as shown on details. Anchor embedment into
substrate material shall be beyond wall dressing or stucco.
3. When used in areas requiring wind borne debris protection this product complies with
Section 1609.1.2 of the current Florida Building Code and does not require an impact
resistant covering.
4. Site conditions that deviate from the details of drawing NCTL210-3874-1-FBC require further
engineering analysis by a licensed engineer or registered architect.
5. See Installation Instructions NCTL210-3874-1-FBC for size and design pressure limitations.
Hermes F. Norero, P.E.
Florida No. 73778
Page 2 of 4
w
r
7
• Date: 0o: 30014
BUILDING DROPS
Report No: 91
A Perfect Solution in Every Drop
• Certificate of Authorization: 29578
Quality Assurance: The manufacturer has demonstrated compliance of products in accordance with the
Florida Building Code for manufacturing under a quality assurance program audited
by an approved quality assurance entity through National Accreditation and
Management Institute (FBC Organization #: QUA 1789)
Performance Standards: The product described herein has been tested per:
• TAS 201-94
• TAS 202-94
• TAS 203-94
Referenced Data: 1. Product Testing performed by National Certified Testing Laboratories NW
(FBC Organization # TST9341)
Report #: NCTL-210-3874-1, Report Date: 4/18/2013
2. Certification Agency
National Accreditation and Management Institute
(FBC Organization #: CER 1773)
3. Material Certification
Miami Dade RER — Product Control Section NOA
E.I. DuPont De Nemours & Co., Inc.: PVB Interlayer
4. Material Certification
Miami 'Dade RER — Product Control Section NOA
Quanex Building Products: PVC Extrusions
Hermes F. Norero, P.E.
Florida No. 73778
Page 3 of 4
y
BUILDING DROPS Dater 0014
Report Noo:: 3091
A Perfect Solution in Every Drop
• Certificate of Authorization: 29578
Through Frame Installation: 1. Approved anchor types and substrates areas follows:
A. For concrete (Min. f'c = 3000 psi) or masonry substrate (Min. f'c = 1500 psi) where one
by (1X), non-structural, wood bucking is employed, use (1) 3/16" diameter ITW Tapcon
type concrete screw anchors per location of sufficient length to achieve minimum
embedment of 1.25" into concrete or masonry.
B. For concrete (Min. f'c = 3000 psi) or masonry substrate (Min. f'c = 1500 psi) where wood
bucking is NOT employed, use (1) 3/16" diameter ITW Tapcon type concrete screw
anchors per location of sufficient length to achieve minimum embedment of 1.25" into
concrete or masonry.
C. For steel substrate, use (1) #8 Tek Screw type steel frame (min. 18ga.) anchors per
location of sufficient length to achieve minimum three threads of penetration beyond
steel structure.
Nail Fin Installation (Where applicable):
A. For wood substrates (Min. S.G. = 0.42) use (1) #10 Wood Screw type installation anchors
per location of sufficient length to achieve a minimum embedment of 1.50" into the
wood substrate.
Refer to Installation Instructions (NCTL210-3874-1-FBC) for anchor spacing and more details of the
installation requirements.
Design Pressure:
Design Pressure
Positive 50 PSF
Negative 60 PSF
Hermes F. Norero, P.E.
Florida No. 73778
Page 4 of 4