The URL can be used to link to this page

Home My WebLink AboutEVALUATION REPORT ASPHALT ROOF SHINGLESQOTRINITYIERD EVALUATION REPORT Owens Corning One Owens Corning Parkway Toledo, OH 43659 N0V282op t E-wi1TI;dG 5t. Lucie OountY, FL EXTERIOR RESEARCH & DESIGN, I.I.C. Certificate of Authorization #9503 353 CHRISTIAN STREET, UNIT #13 OXFORD, CT 06478 PHONE: (203) 262-9245 FAX: (203) 262-9243 Evaluation Report 037940.02.12-R7 FL10674-1112 Date of Issuance: 02/06/2012 Revision 7: 04/18/2016 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code sections noted herein. DESCRIPTION: Owens Corning Asphalt Roof Shingles LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 8. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 04/18/2016. This does not serve as an electronically signed document. Signed, sealed hardcopies have been transmitted to the Product Approval Administrator and to the named client CERTIFICATION OF INDEPENDENCE: 1. TrinitylERD does not have, nor does it intend to acquire or will it acquire, a financial interest,in any company manufacturing or distributing products it evaluates. 2. Trinity I ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither Trinity) ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. ROOFING SYSTEMS EVALUATION: 1. SCOPE: Product Category: Roofing Sub -Category: Asphalt Shingle Compliance Statement: Owens Corning Asp compliance with the following sections of tF through testing in accordance with the folloi and Limitations / Conditions of Use set forth 2. STANDARDS: i r^ 1 QOTRINITYIERD salt Roof Shingles, as produced by Owens Corning, have demonstrated e Florida Building Code and Florida Building Code, Residential Volume sing Standards. Compliance is subject to the Installation Requirements ierein. Section Property I Standard Year 1507.2.5, R905.2.4 Physical Properties ASTM D3462 2009 1507.2.7.1, R905.2.6.1 Wind Resistances ASTM D3161 2009 1507.2.7.1, R905.2.6.1 Wind Resistance, ASTM D7158 2008 3. REFERENCES: Entity Examination I Reference Date UL LLC (CER9626) Physicals & Wind Resistance File R2453, Vol. 3 02/15/2007 UL LLC (CER9626) Physicals & Wind Resistance 20120516-112453 05/16/2012 UL LLC (TST9628) Physical Properties 06CA20263 04/18/2006 UL LLC (TST9628) Wind Resistance 11CA34308 02/18/2012 UL LLC (TST9628) Physicals & Wined Resistance 4786093137 02/01/2014 UL LLC (TST9628) Wind Resistance 4786126532 02/10/2014 UL LLC (TST9628) Physical Properties Classification letter 02/13/2014 UL LLC (TST9628) Physical Properties Classification letter 10/02/2015 Miami -Dade (CER1592) FBC HVHZ Compliance Various NOAs Various UL LLC (QUA9625) Quality Controll Service Confirmation, R2453 Exp. 08/20/2017 4. PRODUCT DESCRIPTION: 4.1 Asphalt Shingles: 4.1.1 Classic and Supreme' are fiberglass reinforced, 3-tab asphalt roof shingles. 4.1.2 Berkshire are fiberglass reinforced,) 4-tab asphalt roof shingles. 4.1.3 Devonshire'"" are fiberglass reinforced, 5-tab asphalt roof shingles. 4.1.4 Duration®, TruDefinitioe Duratiol., Duration Premium Cool, TruDefinition' Duration® Designer Color Collection, TruDefinition' 0akridge , Oakridge' and WeatherGuard® HP are fiberglass reinforced, laminated asphalt roof shingles. 4.2 Berkshire® Hip & Ridge Shingles, High Ridge, WeatherGuard HP Hip & Ridge Shingles, ProEdge Hip & Ridge Shingles and DuraRidgeTm Hip & Ridge Shingles are fiberglass reinforced, hip and ridge asphalt roof shingles. 4.3 Starter Strip Shingle, Starter Strip Pilus and Starter Shingle Roll are starter strips for asphalt roof shingles. S. LIMITATIONS: 5.1 This is a building code evaluation. Neither TrinitylERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any projection which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for u 5.3 Fire Classification is not part of thi for fire ratings of this product. in the HVHZ. Evaluation Report; refer to current Approved Roofing Materials Directory Exterior Research and Design, I.I.C. Evaluation Report 037940.02.12-117 Certificate of Authorization #9503 FL10674-1112 Revision 7: 04/18/2016 Page 2 of 8 QOTRINITYIERD 5.4 Wind Classification: 5.4.1 All Owens Corning shingles noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F and/or ASTM D7158, Class H, indicating the shingles are acceptable for use in all wind zones up to Vasd = 150 mph (V,,it = 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.2 All Owens Corning hip & ridge shingles, Starter Strip. Shingle and Starter Strip Plus noted herein are Classified in accordance with FBC Tables 1507.2.7.1 and R905.2.6.1 to ASTM D3161, Class F, indicating the shingles are acceptable for use in all wind zones up to Vasd = 150 mph (Vult = 194 mph). Refer to Section 6 for installation requirements to meet this wind rating. 5.4.3 Classification by ASTM D7158 applies to exposure category B or C and a building height of 60 feet or less. Calculations by a qualified design professional are required for conditions outside these limitations. Contact the shingle manufacturer for data specific to each shingle. 5.4.4 Refer to Owens Corning published information on wind resistance and installation limitations. 5.5 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building Code and F.A.C. Rule 61G20-3. 6. INSTALLATION: 6.1 Underlayment: 6.1.1 Underlayment shall be acceptable to Owens Corning and shall hold current Florida Statewide Product Approval, or be Locally Approved per Rule 61G20-3, per FBC Sections 1507.2.3, 1507.2.4 or R905.2.3. 6.2 Asphalt Shingles: 6.2.1 Installation of asphalt shingles shall comply with the manufacturer's current published instructions, using minimum four (4) nails per shingle in accordance with FBC Sections 1507.2 or R905.2, with the following exceptions: ➢ Berkshire shingles require minimum five (5) nails per shingle. ➢ WeatherGuardm HP shingles require minimum six (6) nails per shingle. Devonshire'" shingles require minimum six (6) nails per shingle. Starter Strip Shingle and Starter Strip Plus require minimum five (5) nails per strip. Refer to Owens Corning published information on wind resistance and installation limitations. 6.2.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.2.4 Where the roof slope exceeds 21 units vertical in 12 units horizontal, special methods of fastening are required. See figures below for details. 6.2.5 Minimum Nailing — Starter Strip Shingle and Starter Strip Plus: Fekundedayment Deck Sdkdhered Weeterlock9 undedaymant ' Drip edge Drip— edge . ' Nags located 2"-3' hom eave InetslfitstStarterStripPlus Selina edalon eae with V removed positioned along cave Starter pPlus overhangseaves and ralm1/4"-3/4" Exterior Research and Design, I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization #9503 F1.10674-1112 Revision 7: 04/18/2016 Page 3 of 8 6.2.6 Minimum Nailing - Classic® & Suprem;e: Normal Mansard.or Wind Areas High-Wiftnd Area pan vihrtos norrnaies Areas' t IAI t 107.1 t�• to EYpasun t:rposicl6n 6.2.7 Minimum Nailing - Berkshire®: M Standard Fastening Pattern Exterior Research and Design, I.I.C. Certificate of Authorization #9503 TTRINITYERD Normal Mansard or Ar"'par& 1NindAeaas High,INlnd duvanesy Area Ostei wentos norinates Araas' viontos faros 6 6/8',Exposun: Expoaieldn Sealant strip La tba doseNador �t• 8Yt• 8Ih• 8w, 8w r Sealaritstiip La tha de selkdor -►.a :ate-► to S , Mai sard or Steep Slope Fastening Pattern 6-Nail Fastening Pattern 1° Evaluation Report 037940.02.12-117 F1.10674-1112 Revision 7: 04/18/2016 Page 4 of 8 6.2.8 Minimum Nailing — Devonshire TM: 1" 7" 8" 8" 8" 7" 1" N. darta 5.5/8' exposure Sealant location Exposid6n de 5 -6/8 ping Ubiced6n del sellador r - QOTRINITYIER'D Nails ,• r e r IS u• sw en• Ten t" Spots of Asphalt Roof Cement Standard 6-Nail Fastening Pattern Mansard or Steep Slope Fastening Pattern 6.2.9 Minimum Nailing — Duration°, TruDefinition® Duration, Duration° Premium Cool & TruDefinition Duration Designer Color Collection: "an Fastening Patter . sunNaszDrutemnynavAeni ►W%Ty", 1" tr 't2a • f stia= aam. i Standard Fastenina Pattern Exterior Research and Design, LLC. Certificate ofAuthoriration #9503 63iatl Fastening Pattern. S,eatLiil®tmLeN,p aka W15h r tr• tr evr san^ Mansard or Steep Slope Fastening Pattern 6-Nail Fastening Pattern Evaluation Report 037940.02.12-117 FL10674-1112 Revision 7: 04/18/2016 Page 5 of 8 6.2.1 Minimum Nailing —TruDefinitione0akridge", Oakridge®: I Standard Fastening Pattern 12- SuregaN fashming am w1ifth I Pau P Spab OWP—W Rook* C*W&M Maksard or Steep Slope Fastening Pattern 6.2.1 Minimum Nailing — WeatherGuardjlHP- - QI KINITYIERD 6-Nail Fastening Pattern I Onalie"We'Aw. t1m Mir nqM&hPkffl lima Exterior Research and Design, I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization #9503 F1.10674-1112 Revision 7:04/18/2016 1 Page 6 of 8 w QOTRINITYIERD 6.3 Hip & Ridge Shingles: 6.3.1 Installation of Berkshire Hip and Ridge Shingles, High Ridge, WeatherGuardo HP Hip and Ridge Shingles and ProEdge Hip & Ridge Shingles shall comply with the manufacturer's current published instructions, using four (4) nails per shingle. Installation of DuraRidgeTm Hip & Ridge Shingles shall comply with the manufacturer's current published instructions, using two (2) nails per shingle. Refer to Owens Corning published information on wind resistance and installation limitations, including the use of hand -sealing for wind warranties. 6.3.2 Fasteners shall be in accordance with the manufacturer's published requirements, but not less than FBC 1507.2.6 or R905.2.5. Staples are not permitted. 6.3.3 Minimum Nailing — Berkshire® Hip & Ridge and High Ridge: #Jgo.. Q: � :Aewil�rmnd .;Direction �Nads` ,. A • ExPoWe I I ,p, �• I 'I I I e- 6.3.4 Minimum Nailing—WeatherGuard® HP Hip and Ridge: Fig. C,Hip &Ridge :Shingle Fastening TOPYL-W Nalb Naps r.•- r, 2^ V. E1lposare 'y1 Exterior Research and Design, LLC. Evaluation Report 037940.02.12-R7 Certificate of Authorization #9503 FL30674-1112 Revision 7: 04/18/2016 Page 7 of 8 6.3.5 Minimum Nailing - ProEdge Hip & Ridge Shingles: PrevaRing Wind Direction selhM Strip A--' 8° Exposure With QOTRINITYIERD Standard �17°• Pstenin atter g --�� ICY 12° 1 Se�llllt 6° Eapos t I 6.3.6 Minimum Nailing — DuraRidgeTm Hip & Ridge Shingles: Note: The drawings below pertain to (minimum, as -tested attachment requirements. Refer to Owens Corning published installation instructions for, their minimum requirements. i7=ico do m djvmt Wranddndd 41mm pndordd MIR &_kl� 7. LABELING: 7.1 Labeling shall be in accordance m herein. 7.2 Asphalt shingle wrappers shall indi Table 1507.2.7.1 / R905.2.6.1. S. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Au& this'product. 9. MANUFACTURING PLANTS: Contact the named QA entity for informat requirements. 10. QUALITY ASSURANCE ENTITY: UL LLC— QUA9,625 ; (414) 248-6409; karen.b Top Vlew � ge�r[or u Ct Ctau j° • OmnsConing 9umW a O � I I �le>± U I I iz the requirements the Accredited Quality Assurance Agency noted compliance with one of the required classifications detailed in FBC Having Jurisdiction in order to properly evaluate the installation of n on which plants produce products covered by Florida Rule 9N-3 QA - END OF EVALUATION REPORT - Exterior Research and Design, I.I.C. Evaluation Report 037940.02.12-R7 Certificate of Authorization #9503 F1.10674-1112 Revision 7: 04/18/2016 Page 8 of 8