HomeMy WebLinkAboutEVALUATION REPORT - CONCRETE ROOF TILESQ0TP,uN1TYJERD
EVALUATION REPORT
EXTERIOR RESEARCH & DESIGN, LLC.
Certificate of Authorization #9503
353 CHRISTIAN STREET, UNIT #13
OXFORD, CT 06478
PHONE: (203) 262-9245
FAX: (203) 262-9243
17=0 �p �c- /�, Entegra Roof Tile, LLC Evaluation Report E39310.11.11-1-R3
N 1 EGIQ 1 1289 NE 9th Avenue FL7804-119
F: O O 1= T 1 L E Okeechobee, FL 34972 Date of Issuance: 11/02/2011
Revision 3: 04/18/2016
SCOPE:
This Evaluation Report is issued under Rule '61G20-3 and the applicable rules and regulations governing the use,of
construction. materials in the State of Florida. -The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code' and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 5th Edition (2014) Florida Building Code
(HVHZ) sections noted herein.
DESCRIPTION: Entegra Concrete Roof Tiles (HVHZ jurisdictions)
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the
referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change.
Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the
product changes or the referenced Quality Assurance documentation changes. TrinityJERD requires a complete
review of this Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinityl ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the. user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 9.
Prepared by:
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized by Robert Nieminen,
P.E. on 04/18/2016. This does not serve as an electronically signed
document. Signed, sealed hardcopies have been transmitted to the
Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. Trinityl ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinityl ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinityl ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
t'• ,
rTRINITY I ERD
ROOFING SYSTEM EVALUATION:
1. SCOPE: `
Product Category: Roofing i
Sub -Category: Roofing Tiles I
Compliance Statement: Entegra Concretes Roof Tiles, as produced by Entegra Roof Tile, LLC, have demonstrated
compliance with the following sections of the Florida Building Code through testing in accordance with the following
Standards. Compliance -is subject to the Installation Requirements and Limitations / Conditions of Use set forth
herein.
2. STANDARDS:
Section
Pro e
1523.6.5.2
Physical Properties
1523.6.5.2
Wind Driven Rain
1523.6.5.2.2
Static Uplift Resistance
1523.6.5.2.3
Static Uplift Resistance
1523.6.5.2.3
Static Uplift Resistance
3. REFERENCES:
Enti
Examination
ERD (TST6049)
TAS 101
ATL (TST3782)
Physical Properties
ATL (TST3782)
Physical Properties
ATL (TST3782)
Physical Properties
ATL (TST3782)
Physical Properties I
ATL (TST 3782)
Physical Properties I
ATL (TST 3782)
Physical Properties
ATL (TST 3782)
Physical Properties I
ATL (TST 3782)
Physical Properties
ATL (TST 3782)
Physical Properties
Miami -Dade (CER1592)
HVHZ Compliance
Miami -Dade (CER1592)
HVHZ Compliance C
Miami -Dade (CER1592)
HVHZ Compliance
Miami -Dade (CER1592)
HVHZ Compliance
Miami -Dade (CER1592)
HVHZ Compliance
Tile Roof Institute
TA5100, TAS 101, 102, 102(A)
PRI (QUA9110)
Quality Assurance
Exterior Research and Design, I.I.C.
Certificate o/Authorization #9503
Standard
TAS 112
TAS 100
TAS 101
TAS 102
TAS 102(A)
Reference
P39740.02.12
RT0624.05-14
RT0624.04-14
RT1210.02-15
RT1210.03-15
RT1103.01-15
RT1103.02-15
RT1103.03-15
RT1103.04-15
RT1103.05-15
14-0416.12
15-0721.04
16-0112.06
16-0112.07
16-0112.08
Membership Confirmation
Inspection Report
Year
1995
1995
1995
1995
1995
Date
02/21/2012
07/03/2014
07/07/2014
12/17/2015
12/17/2015
11/07/2015
11/07/2015
11/07/2015
11/07/2015
11/07/2015
11/27/2014
11/05/2015
02/25/2016
02/25/2016
02/25/2016
Current
11/04/2015
Evaluation Report E39310.11.11-1-R3
FL7804-R9
Revision 3: 04/18/2016
Page 2 of 9
TRINITY I ERD
4. PRODUCT DESCRIPTION:
4.1 BERMUDA FLAT, PLANTATION FLAT and HORIZON FLAT are TAS 112, Type 3a (flat -profile) concrete roof tiles.
i- 16' �
T4'
I
10,
r
16' �
T-
2'
10'
r
16�?
Bermuda Flat
Plantation Flat
r,
13"
'17-U4"
� .
Horizon Flat
Exterior Research and Design, I.I.C.
Certificate of Authorization #9503
Evaluation Report E39330.11.11-1-R3
FL7804-R9
Revision 3: 04/18/2016
Page 3 of 9
4.2 BELLA HIGH "S" are TI
4.3 ESTATE "S" and HACIE
Exterior Research and Design, I.I.C.
Certificate of Authorization #9503
INITY I ERD
es.
Evaluation Report E39310.11.11-1-R3
FL7804-R9
Revision 3: 04/18/2016
Page 4 of 9
I
5.
i
TRINITY I ERD
4.4 GALENA SPANISH "S" and REGAL are TAS 112, Type 2a (non -interlocking, high -profile) concrete roof tiles.
17"
Galena Spanish "S"
Regal
10"
LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is. for use in FBC HVHZ jurisdictions or other jurisdictions adopting FBC HVHZ
requirements.
5.3 Fire classification is not part of this evaluation; refer to FBC Section 1516 or current Approved Roofing
Materials Directory for fire rating of this product.
5.4 Reference is made to FBC Section 1512.4.2.4 regarding field testing of completed tile roof installations.
5.5 Applicant shall retain the services of an FBC listed, accredited laboratory to perform quarterly tests in
accordance with TAS 112, Appendix 'A'. Such testing shall be submitted to Trinity I ERD for review.
5.6 Minimum underlayment shall comply with the RAS 118, RAS 119 or RAS 120, as applicable. Underlayment
products shall hold Florida Statewide Product Approval or Local Approval for. use in tile roof assemblies in
HVHZ jurisdictions.
5J Minimum roof deck requirements shall be in accordance with applicable FBC HVHZ requirements.
5.8 All products in the roof assembly shall have quality assurance audit in accordance with the Florida Building
Code and F.A.C. Rule 61G20-3.
Exterior Research and Design, I.I.C.
Certificate of Authorization #9503
Evaluation Report E39310.11.11-1-113
FL7804-119
Revision 3: 04/18/2016
Page 5 of 9
6.
�l TRINITY I ERD
INSTALLATION:
6.1 Entegra Concrete Roof Tiles may be mechanically fastened, mortar -set or adhesive -set. Installation shall
comply with manufacturer's current published instructions, but not less than the requirements of RAS 118,
RAS 119 or RAS 120, as applicable.
6.2 Attachment Calculations: Entegra Concrete Roof Tile shall be evaluated as a 'Moment -Based System' in
accordance with RAS 127-11 usinle the data outlined herein.
TABLE 1: AERODYNAMIC MULTIPLIERS-%L (FT3)
Tile
Batten Application
Direct -Deck Application
Bermuda Flat
0.189
0.205
Plantation Flat
0.267
0.289
Horizon Flat
0.305
0.330
Bella High "S"
` 0.349
0.378
Estate "S"
0.267
0.289
Hacienda
I 0.267
0.289
Galena Spanish "S"
N/A
0.235
Regal
0.287
0.311
TABLE 2: RESTORING MOMENT DUE TO GRAviTY - Mr (FT-LBF)
Roof Slope (0)
Tile
2:12<0<3:12
3:12<6<4:121
4:12<0<5:12
5:22<0<6:12
6:12<0<7:12
0>7:12
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Battens
Direct
Bermuda Flat
5.22
6.43
5.17
6,37
5.09
6.27
4.98
6.15
4.86
6.00
4.72
5.83
Plantation Flat
7.22
7.91
6.85
7.79 I
6.75
7.67
6.61
7.52
6.44
7.32
6.26
7.04
Horizon
1.60
8.32
7.52
8.241
7.41
8.12
7.26
7.95
7.09
7.76
6.89
7.55
Bella High "S"
6.19
6.89
6.11
6.80 1
. 5.99
6.67
5.85
6.51
5.68
6.33
5.50
6.13
Estate "S"
6.14
6.84
5.91
6.74 j
5.82
6.64
5.70
6.50
5.56
6.33
5.40
6.14
Hacienda
5.92
6.80
5.92
6.80
5.82
6.69
5.70
6.55
5.56
6.39
5.41
6.22
Galena Spanish "S"
N/A
6.20
N/A
6.13
N/A
6.03
N/A
5.89
N/A
5.74
N/A
5.57
Regal
7.77
8.34
7.77
8.34
I 7.65
8.20
7.49
8.03
7.30
7.83
7.10
7.61
0
Exterior Research and Design, LLC.
Certificate of Authorization #9503
Evaluation Report E39310.11.11-1-R3
FL7804-R9
Revision 3: 04/18/2016
Page 6 of 9
J TRINITY ERD
TABLE 3B-2: ATTACHMENT RESISTANCE EXPRESSED AS A MOMENT- MF (FT-LBF)
LOW PROFILE TILES, MORTAR & ADHESIVE -SET SYSTEMS -
Tile
Application
Adhesive
Size (inch)
Weight (g)
Mf (ft-Ibf)
To
Substrate
To Tile
To
Substrate
To Tile
Estate "S" or Hacienda
Inter-
Dependent
TILE BOND'"`
1 x 6•
1 x 6
-11
-11
43.8
Touch'n Seal'" StormBond
1.25 x 10
0.75 x 10
-8.4
-5.1
41.8
ICP Adhesives Polyset RTA-1;
cross -bond
"5" long
oblong
-4.5 across
head
�6
^5
44.0
ICP Adhesives Polyset AH-160
4 x 4
2 x 4
1 -16
1 -8
1 49.9
Independent
ICP Adhesives Polyset AH-160
2 x 7
N/A
-30
N/A
36.5
2 x 10
N/A
-54
N/A
60.4
Mortar
Per RA5 120 and Product Approval of Mortar Mfgr
20.6
TABLE 3C-1: ATTACHMENT RESISTANCE EXPRESSED AS A MOMENT - MF (FT-LBF)
HIGH PROFILE TILES, MECHANICALLY ATTACHED SYSTEMS
Tile
Fastener
Direct -Deck
(min. 15/32"
plywood)
Direct -Deck
(min.19/32"
plywood)
Battens
Type
#
Size
Shank
Clip
Nail
One (1)
lod
Smooth or Screw
N/A
5.1
6.8
2.8
Nail
Two (2)
10d
Smooth or Screw
N/A
6.9
9.2
7.3
Nail
One (1)
10d
Smooth or Screw
Field
23.1
23.1
19.0
Nail
One (1)
10d
Smooth or Screw
Eave
29.3
29.3
24.0
"S",
Nail
Two (2)
10d
Smooth or Screw
Field
27.6
27.6
38.6
Bella High Galena-
Spanish "S" Regal
Nail
Two (2)
10d
Smooth or Screw
Eave
38.1
38.1
41.8
or
Nail
Two (2)
10d
Ring
N/A
28.6
41.2
19.4
Nail'
Two (2)'
10d'
Ring'
N/A
33.11
48.1'
50.91
Screw
One (1)
#8
N/A
N/A
20.7
20.7
18.1
Screw
Two (2)
#8
N/A
N/A
43.2
43.2
29.8
'Installation with a 4-inch tile headlap and fasteners located min. 2'/:-inch from head of tile.
TABLE 3C-2; ATTACHMENT RESISTANCE EXPRESSED AS A MOMENT- MF (FT-LBF)
HIGH PROFILE TILES, MORTAR & ADHESIVE -SET SYSTEMS
Tile
Application
Adhesive
Size (inch)
Weight (g)
Mf (ft-Ibf)
To
Substrate
To Tile
To
Substrate
To Tile
Bella High "5", Galena
'Spanish "S" or Regal
Inter -
Dependent
TILE BOND"
1 x 6
1 x 10
-11
^22
48.1
Touch'n Seal'" StormBond
1.25 x 30
0.75 x 8
-8.4
^3.9
51.6
ICP Adhesives Polyset RTA-1;
cross -bond
two (2) -6"
long oblong
-10" across
I head
-12 each
-15
36.2
ICP Adhesives Polyset AH-160
4 x 4
2 x 4
-16
^ 8
30.1
t
Independent ,
ICP Adhesives Polyset AH-160
2 x 7
N/A
-30
N/A
48.5
2 x 10
N/A
-'63
N/A
93.5.
Mortar
Per RA5120 and Product Approval of Mortar Mfgr
24.5
Exterior Research and Design, I.I.C. Evaluation Report E39310.11.11-1-R3
Certificate of Authorization 0503 FL7804-R9
Revision 3: 04/18/2016
Page 8 of 9
Q'TRINITYIERD
TABLE 3A-1: ATTACHMENT RESISTANCE EXPRESSED ASA MOMENT- MF (FT-LBF)
FLAT PROFILE TILES, MECHANICALLY ATTACHED SYSTEMS
Tile
Fastener
Direct -Deck
(min.15/32"
plywood)
Direct -Deck
(min.19/32"
plywood)
Battens
e
Type
#
Size
Shank
Clip
p
Nail
One (1)
10d
Smooth or Screw
N/A
7.3
9.8 •
4.9
Nail
Two (2)
130d
Smooth or Screw
N/A
14.0
18.8
7.4
Nail
One (1)
110d
Smooth or Screw
Eave
19.0
19.0
22.1
Nail
One (1)
10d
Smooth or Screw
Field
24.3
24.3
24.2
Bermuda Flat,
Nail
Two (2)
lOd
Smooth or Screw
Eave
31.9
31.9
32.2
Plantation Flat or
Nail
Two (2)
lOd
Smooth or Screw
Field
35.5
35.5
34.8
Horizon
Nail
Two (2)
i3Od
Ring
N/A
30.9
38.1
17.2
Nail'
Two (2)'
10d'
Ring'
N/A
50.3'
65.5'
48.3'
Screw
One (1)
#8
N/A
N/A
30.8
30.8
18.2
Screw
Two (2)
#8
N/A
N/A
51.7
51.7
24.4
' Installation with a 4-inch tile headlap and fasteners located min. 2%-inch from head of tile.
TABLE 3A-2: ATTACHMENT IRESISTANCE EXPRESSED -AS A MOMENT- MF (FT-LBF)
FLAT PROFILE TILES, ADHESIVE -SET SYSTEMS
Tile
Application
1
Adhesive
Size (inch)
Weight (g)
Mf (ft-lbf)
To
Substrate
To Tile
To
Substrate
To Tile
�
Bermuda Flat,
Plantation Flat or
Horizon
Inter -
Dependent
TILE BOND- I
1 x 6
1 x 6
-11
-11
40.6
Touch 'n Seal'" StormBond
1.25 x 10
1.25 x 8
-8.3
-10.2
73.2
ICP Adhesives Polyseti RTA-1;
cross -bond . I
-5" long
oblong
-4.5"
across head
-9
^'S
51.8
I ICP Adhesives PolysetlAH-160
4 x 4
2 x 4
-16
-8
42.8
Independent
ICP Adhesives Polyset �, H-160
2 x 7
N/A
-30
N/A
50.9
2 x 10
N/A
-45
N/A
91.9
TABLE 3B-1: ATTACHMENT RESISTANCE EXPRESSED AS A MOMENT- MF (FT-LBF) I
LOW PROFILE TILES; MECHANICALLY ATTACHED SYSTEMS
Tile
Type
#
Size
Estate "5" or Hacienda
Nail
One (1).2
10d
Nail
Two (2)
10d
Nail
One (1) 2
10d
Nail
one
30d
Nail
Two (2)
10d
Nail
Two (2)
10d
Nail
Two (2)
10d
Nail'
Two (2)'
iod'
Screw
one
#8
Screw
Two (2)
#8
' Installation with
a 4-inch tile headlap
and
2 For one (1) fastener
installations,
utilize h
Exterior Research and Design, I.I.C.
Certificate of Authorization #9503
Direct -Deck
(min.15/32"
plywood)
Direct -Deck
(min.19/32"
plywood)
Shank
Clip
Smooth or Screw
N/A
8.82
11.82
Smooth or Screw
N/A
16.4
21.9
Smooth or Screw
Eave
19.02
19.02
Smooth or Screw
Field
24.3 2
24.3 2
Smooth or Screw
Eave
31.9
31.9
Smooth or Screw
Field
35.5
35.5
Ring
N/A
27.8
37.4
Ring'
N/A
43.0'
67.5'
N/A
N/A
25.82
25.82
N/A
N/A
47.1
47.1
mers located min. 2Y.-inch from head of tile.
hat is approximately 4%-Inch from the interlocking edge.
Battens
4.1 2
7.1
22.12
24.2 2
32.2
34.8
28.8
22.9'
49.1
Evaluation Report E39310.11.11-1-R3
FL7804-R9
Revision 3: 04/18/2016
Page 7 of 9
TRINITY I ERD
7. LABELING:
7.1 Each unit shall bear the imprint and/or identifiable marking of the manufacturer's name or logo, as detailed
below. Tile lots shall be labeled in accordance with the requirements of the Accredited Quality Assurance
Agency noted herein.
1
and/or
ENTEURR
Labeling: Bermuda Flat, Plantation Flat, Estate "S", Bella High "S", Galena Spanish "S"
and/or
H,. n o.n
Labeling: Horizon flat, Hacienda, Regal
8. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
9. MANUFACTURING PLANTS:
Plant
Profiles
Okeechobee, FL
Bermuda Flat, Plantation Flat, Estate "S", Bella High "S", Galena Spanish "S"
Ft. Myers, FL
Horizon Flat, Hacienda
Deerfield Beach, FL
Horizon Flat, Hacienda, Regal
10. QUALITY ASSURANCE ENTITY:
PRI Construction Materials Technologies, LLC. — QUA9110; (813) 621-5777
- END OF EVALUATION REPORT —
Exterior Research and Design, I.I.C. Evaluation Report E39310.11.11-1-R3
Certificate of Authorization #9503 FL7804-R9
Revision 3: 04/18/2016
Page 9 of 9