HomeMy WebLinkAboutNOA - PLANTATION ROOF TILE MIAMI-DADE COUNTY
MIMIAMI- PRODUCT CONTROL SECTION
• 11805 SW 26 Street,Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES(RER) Miami,Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T(786)315-2590 F(786)315-2599
NOTICE OF ACCEPTANCE (NOA) www.miamidade.goy/economy
Boral Roofing,LLC
7575 Irvine Center Drive, Suite 100
Irvine,CA 92618
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami-Dade County RER-Product Control Section to be
used in Miami-Dade County and other areas where allowed by the Authority Having Jurisdiction(AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control Section
(in Miami-Dade County)and/or the AHJ(in areas other than Miami-Dade County)reserve the right to have this product
or material tested for quality assurance purposes. If this product or material fails to perform in the accepted manner,the
manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or suspend the use
of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance, if it is
determined by Miami-Dade County Product Control Section that this product or material fails to meet the requirements
of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Plantation Roof Tile
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami-Dade County Product Control Approved",unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials,use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of
this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA#20-1019.02 and consists of pages 1 through 7.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 21-0420.07
MIAMI•DADE COUNTY Expiration Date: 12/08/25
Approval Date: 08/26/21
Page 1 of 7
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub-Category: Roofing Tiles
Material: Concrete
1. SCOPE
This approves a roofing system using Boral Plantation Concrete Roof Tile, as manufactured by Boral Roofing, LLC
in Okeechobee, FL as described in Section 2 of this Notice of Acceptance, designed to comply with the Florida
Building Code for High Velocity Hurricane Zone. For use in locations where the pressure requirements, as determined
by applicable Building Code, do not exceed the design pressure values obtain by calculations in compliance with RAS
127 using the values listed in section 4 herein. The attachment calculations shall be prepared as a moment based
system.
2. PRODUCT DESCRIPTION
Manufactured by Dimensions Test Product
Applicant Specifications Description
Plantation Tile Length: 16'/2" TAS 112 Flat profile concrete roof tile,
Width: 13" Type 3a Interlocking, Class III;
for direct deck or battened nail-on,
mortar or adhesive set applications.
Trim Pieces L=varies TAS 112 Accessory trim, concrete roof pieces for
W=varies use at hips,rakes,ridges and valley
Varying thickness terminations. Manufactured for each tile
profile.
2.1. MANUFACTURING LOCATION
1. Okeechobee, FL
2.2 PRODUCTS MANUFACTURED BY OTHERS
Product Name Product Description Manufacturer
(With Current NOA)
ICP Adhesives Polysee AH-160 Two component polyurethane ICP Adhesives and Sealants,Inc.
foam adhesive.
TILE BOND TM Roof Tile Adhesive Single component polyurethane The Dow Chemical Company
foam roof tile adhesive.
Touch `N Seal StormBone 2 Two- Two component polyurethane DAP Foam, Inc.
Component Polyurethane Roof Tile foam adhesive.
Adhesive
Touch `N Seal StormBone One One component polyurethane DAP Foam, Inc.
Component Polyurethane Roof Tile foam adhesive.
Adhesive
Quikrete"Roof Tile Mortar,FL-15 Premixed,pre-bagged gray roof The Quikrete Companies,Inc.
tile mortar.
NOA No.: 21-0420.07
MIAMI•DADE COUNTY Expiration Date: 12/08/25
Approval Date: 08/26/21
Page 2 of 7
2.3 SUBMITTED EVIDENCE:
Test Agency Test Identifier Test Name/Report Date
American Test Lab of South RT0624.05-14 TAS 112 07/03/14
Florida RT0817.07-20 TAS 112 08/14/20
Redland Technologies 7161-03 Static Uplift Testing Dec. 1991
Appendix III PA 102&PA 102(A)
The Center for Applied 94-060B Static Uplift Testing March 1994
Engineering,Inc. PA 101 (Adhesive Set)
94-084 Static Uplift Testing May 1994
PA 101 (Mortar Set)
Redland Technologies 7161-03 Wind Tunnel Testing Dec. 1991
Appendix II PA 108 (Nail-On)
Letter Dated Aug. 1, 1994 Wind Tunnel Testing Aug. 1994
PA 108 (Nail-On)
P0631-01 Wind Tunnel Testing July 1994
PA 108 (Mortar Set)
P0402 Withdrawal Resistance Testing of Sept. 1993
screw vs. smooth shank nails
The Center for Applied Project No. 307025 Wind Driven Rain Oct. 1994
Engineering,Inc. Test#MDC-76 PA 100
Walker Engineering, Inc. Calculations Aerodynamic Multiplier March 1999
April 1999
Calculations 25-7183 March 1995
25-7094 February 1996
25-7496 April 1996
Calculations 25-7584 December 1996
25-7804b-8
25-7804-4& 5
25-7848-6
Calculations Two Patty Adhesive Set System April 1999
Farabaugh Engineering and T295-11 TAS-108 10/05/11
Testing Inc. T306-11 TAS-108 10/04/11
T279-11 TAS-108 09/23/11
PRI Construction Material DAPF-004-02-08 TAS 101 07/26/18
Technologies DAPF-004-02-09 TAS 101 07/26/18
DAPF-004-02-10 TAS 101 07/26/18
2002T0003.05 TAS 101 11/06/20
NOA No.: 21-0420.07
MIAMI•DADE COUNTY Expiration Date: 12/08/25
Approval Date: 08/26/21
Page 3 of 7
3. LIMITATIONS
3.1 Fire classification is not part of this acceptance.
3.2 For mortar or adhesive set tile applications, a static field uplift test shall be performed in accordance with
TAS 106.
3.3 Applicant shall retain the services of a Miami-Dade County Certified Laboratory to perform quarterly test
in accordance with TAS 112, appendix `A'. Such testing shall be submitted to the Miami-Dade Product
Control office for review.
3.4 Minimum underlayment shall be in compliance with the applicable Roofing Applications Standards listed
section 4.1 herein.
3.5 Minimum 4/12 slope requirement for mechanically attached tiles.
3.6 30/90 hot mopped underlayment applications may be installed perpendicular to the roof slope unless stated
otherwise by the underlayment material manufacturers published literature.
3.7 This acceptance is for wood deck applications. Minimum deck requirements shall be in compliance with
applicable building code.
3.8 All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code
and Rule 61 G20-3 of the Florida Administrative Code.
4. INSTALLATION
4.1 Plantation Roof Tile and its components shall be installed in strict compliance with Roofing Application
Standard RAS 118,RAS 119 and RAS 120.
4.2 Data For Attachment Calculations
Table 1: Average Weight(W) and Dimensions (I x w)
Tile Profile Weight-W(Ibf) Length-I (ft) Width-w(ft)
Plantation Tile 11.6 1.375 1.08
Table 2: Aerodynamic Multipliers -X (ft3)
Tile X (ft3) X (ft3)
Profile Batten Application Direct Deck Application
Plantation Tile 0.267 0.289
Table 3: Restoring Moments due to Gravity - Mg (ft.-Ibf)
Tile 2": 12" 3": 12" 4": 12" 5": 12" 6": 12" Greater than
Profile 7": 12"
Battens Direct Battens Direct Battens Direct Battens Direct Battens Direct Battens Direct
Deck Deck Deck Deck Deck Deck
Plantation N/A 7.91 N/A 7.79 6.75 7.67 6.61 7.52 6.44 7.32 6.26 7.04
Tile
NOA No.: 21-0420.07
MIAMI•DADE COUNTY Expiration Date: 12/08/25
Approval Date: 08/26/21
Page 4 of 7
Table 4: Attachment Resistance Expressed as a Moment- Mf(ft-lbf)
For Nail-On Systems
Tile Fastener Type Direct Deck Direct Deck Battens
Profile (Min 15/32" (Min. 19/32" plywood)
plywood)
Plantation Tile 2-10d Ring Shank Nails 30.9 38.1 17.2
1-10d Smooth or Screw 7.3 9.8 4.9
Shank Nail
2-10d Smooth or Screw 14.0 18.8 7.4
Shank Nails
1 #8 Screw 30.8 30.8 18.2
2#8 Screw 51.7 51.7 24.4
1-10d Smooth or Screw 24.3 24.3 24.2
Shank Nail Field Clip)
1-10d Smooth or Screw 19.0 19.0 22.1
Shank Nail Eave Clip)
2-10d Smooth or Screw 35.5 35.5 34.8
Shank Nails Field Clip)
2-10d Smooth or Screw 31.9 31.9 32.2
Shank Nails Eave Clip)
2-10d Ring Shank Nails' 50.3 65.5 48.3
1 Installation with a 4"the headla and fasteners are located a minimum of 2'/2"from the head of tile.
Table 5: Attachment Resistance Expressed as a Moment Mf(ft-lbf)
for Two Paddy Adhesive Set Systems
Tile Profile Tile Application Minimum Attachment
Resistance
Plantation Tile TILE BONDTm Roof Tile Adhesive 31.33
ICP Adhesives Pol set®AH-160 31.34
Touch 'N Seal StormBond12 455
Touch 'N Seal StormBond° 766
2 See foam adhesive manufacturer's component approval for installation requirements
3 Medium paddy weight of 13.9 grams per paddy of TILE BONDTm Roof Tile Adhesive
4 Medium paddy weight of 8 grams per paddy of Polyset®AH-160
5 Medium paddy weight of 8 grams per paddy of Touch 'N Seal StormBond °2
6 Medium paddy weight of 18.7 grams between tile and underlayment, paddy weight of 10.5 grams on overlap of tile of
Touch 'N Seal StormBond °(one-component)
NOA No.: 21-0420.07
MiAMI-DADE couNnr Expiration Date: 12/08/25
Approval Date: 08/26/21
Page 5 of 7
Table 6: Attachment Resistance Expressed as a Moment - Mf(ft-Ibf)
for Single Paddy Adhesive Set Systems
Tile Tile Application Minimum Attachment
Profile Resistance
Plantation Tile ICP Adhesives Pol set®AH-160 118.97
ICP Adhesives Pol set®AH-160 40.48
Touch 'N Seal StormBond®2 739
Touch 'N Seal StormBond®2 4810
7 Large paddy weight of 45 grams of Polyset®AH-160
8 Large paddy weight of 24 grams of Polyset®AH-160
9 Large paddy weight of 45 grams of Touch `N Seal StormBond 12
10 Large paddy weight of 24 grams of Touch 'N Seal StormBond °2
Table 7: Attachment Resistance Expressed as a Moment - Mf(ft-Ibf)
for Mortar Set Systems
Tile Profile Tile Application Attachment
Resistance
Plantation Tile Mortar Set' 39.0
Seespecific mortar manufacturer's Notice of Acceptance.
5. LABELING
All tiles shall bear the imprint or identifiable marking of the manufacturer's name or logo as seen below or following
statement: "Miami-Dade County Product Control Approved".
OR
ENTEURR
BORAL PLANTATION ROOF TILE LABEL(LOCATED ON UNDERSIDE OF TILE
6. BUILDING PERMIT REQUIREMENTS:
6.1 Application for building permit shall be accompanied by copies of the following:
6.1.1 This Notice of Acceptance.
6.1.2 Any other documents required by Building Official or Applicable building code in order to properly
evaluate the installation of this system.
NOA No.: 21-0420.07
MIAMI•DADE COUNTY Expiration Date: 12/08/25
Approval Date: 08/26/21
Page 6 of 7
PROFILE DRAWING
BORAL PLANTATION FLAT CONCRETE TILE
I6I�2
13J�
END OF THIS ACCEPTANCE
NOA No.: 21-0420.07
MiAMI-DADe COuNnr Expiration Date: 12/08/25
Approval Date: 08/26/21
Page 7 of 7