HomeMy WebLinkAboutNOA WINDOW WALL SYSTEM NOA No. 20-0910.06
Expiration Date: July 03, 2024
Approval Date: November 12, 2020
11/04/20 Page 1
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DIVISION T (786) 315-2590 F (786) 315-2599 NOTICE OF ACCEPTANCE (NOA) www.miamidade.gov/building
Aldora Aluminum & Glass Products, Inc.
4250 Coral Ridge Drive
Coral Springs, FL 33065
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction
materials. The documentation submitted has been reviewed and accepted by Miami-Dade County RER -
Product Control Section to be used in Miami-Dade County and other areas where allowed by the Authority
Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami-Dade County Product Control
Section (In Miami-Dade County) and/ or the AHJ (in areas other than Miami-Dade County) reserve the right
to have this product or material tested for quality assurance purposes. If this product or material fails to perform
in the accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately
revoke, modify, or suspend the use of such product or material within their jurisdiction. RER reserves the right
to revoke this acceptance if it is determined by Miami-Dade County Product Control Section that this product
or material fails to meet the requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code,
including the High Velocity Hurricane Zone.
DESCRIPTION: Series “Front Set” Aluminum Window Wall System – L.M.I.
APPROVAL DOCUMENT: Drawing No. W14-12, titled “Series Front Set Alum Window Wall Sys.
(L.M.I.)”, sheets 1, 1.1, 2, 3, 3.1, 4, 5, 6, 7, 7.1, 8, 9, 10, 10.1, 11, 11.1, 11.2, 11.3 and 12 through 19 of 19,
dated 03/21/14, with revision E dated 06/25/20, prepared by Al-Farooq Corporation, signed and sealed by Jalal
Farooq, P.E., bearing the Miami-Dade County Product Control Revision stamp with the Notice of Acceptance
number and expiration date by the Miami-Dade County Product Control Section.
MISSILE IMPACT RATING: Large and Small Missile Impact Resistant
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state,
model/series, and following statement: "Miami-Dade County Product Control Approved", unless otherwise
noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no
change in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in
the materials, use, and/ or manufacture of the product or process. Misuse of this NOA as an endorsement of
any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to
comply with any section of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami-Dade County, Florida, and followed
by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then
it shall be done in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors
and shall be available for inspection at the job site at the request of the Building Official.
This NOA revises NOA No. 19-1001.15 and consists of this page 1 and evidence pages E-1, E-2, E-3 and
E-4, as well as approval document mentioned above.
The submitted documentation was reviewed by Manuel Perez, P.E.
Manuel Perez, P.E.
Product Control Examiner
NOA No. 20-0910.06
Expiration Date: July 03, 2024
Approval Date: November 12, 2020
E - 1
Aldora Aluminum & Glass Products, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA’s
A. DRAWINGS
1. Manufacturer's die drawings and sections.
(Submitted under NOA No. 14-0415.06)
2. Drawing No. W14-12, titled “Series Front Set Alum Window Wall Sys. (L.M.I.)”,
sheets 1, 1.1, 2, 3, 3.1, 4, 5, 6, 7, 7.1, 8, 9, 10, 10.1, 11, 11.1, 11.2, 11.3 and 12 through
19 of 19, dated 03/21/14, with revision D dated 11/04/19, prepared by Al-Farooq
Corporation, signed and sealed by Javad Ahmad, P.E.
(Submitted under NOA No. 19-1001.15)
B. TESTS
1. Test reports on: 1) Air Infiltration Test per FBC, TAS 202-94
2) Uniform Static Air Pressure Test Loading per FBC, TAS 202-94
3) Water Resistance Test per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked-up drawings and installation diagram of a Series FS300 aluminum
window wall system, prepared by Fenestration Testing Laboratory, Inc., Test Report
No. FTL-10679, dated 04/24/19, signed and sealed by Idalmis Ortega, P.E.
(Submitted under NOA No. 19-1001.15)
2. Test reports on: 1) Air Infiltration Test per FBC, TAS 202-94
2) Uniform Static Air Pressure Test Loading per FBC, TAS 202-94
3) Water Resistance Test per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
6) Forced Entry Test, per FBC 2411.3.2.1 (b) and TAS 202-94
along with marked-up drawings and installation diagram of a series “Summit”
aluminum outswing doors, prepared by Blackwater Testing, Inc., Test Report No.
BT-ALD-17-001, dated 03/23/18 and revised and re-issued on 11/12/19, signed and
sealed by Constantin Bortes, P.E.
(Submitted under NOA No. 19-1001.15)
3. Test reports on: 1) Air Infiltration Test per FBC, TAS 202-94
2) Uniform Static Air Pressure Test Loading per FBC, TAS 202-94
3) Water Resistance Test per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
6) Forced Entry Test, per FBC 2411.3.2.1 (b) and TAS 202-94
along with marked-up drawings and installation diagram of an aluminum window wall
system, prepared by Fenestration Testing Laboratory, Inc., Test Report No. FTL-7140
dated 11/27/13, signed and sealed by Marlin D. Brinson, P.E.
(Submitted under NOA No. 14-0415.06)
Manuel Perez, P.E.
Product Control Examiner
NOA No. 20-0910.06
Expiration Date: July 03, 2024
Approval Date: November 12, 2020
E - 2
Aldora Aluminum & Glass Products, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA’s
B. TESTS (CONTINUED)
4. Test reports on: 1) Air Infiltration Test per FBC, TAS 202-94
2) Uniform Static Air Pressure Test Loading per FBC, TAS 202-94
3) Water Resistance Test per FBC, TAS 202-94
along with marked-up drawings and installation diagram of an aluminum window wall
system, prepared by Fenestration Testing Laboratory, Inc., Test Reports No.
FTL-7641, dated 03/18/14, signed and sealed by Marlin D. Brinson, P.E.
(Submitted under NOA No. 14-0415.06)
5. Test reports on: 1) Air Infiltration Test per FBC, TAS 202-94
2) Uniform Static Air Pressure Test Loading per FBC, TAS 202-94
3) Water Resistance Test per FBC, TAS 202-94
along with marked-up drawings and installation diagram of an aluminum window wall
system, prepared by Fenestration Testing Laboratory, Inc., Test Reports No.
FTL-7698, dated 03/18/14, signed and sealed by Marlin D. Brinson, P.E.
(Submitted under NOA No. 14-0415.06)
6. Test reports on: 1) Air Infiltration Test per FBC, TAS 202-94
2) Uniform Static Air Pressure Test Loading per FBC, TAS 202-94
3) Water Resistance Test per FBC, TAS 202-94
4) Large Missile Impact Test per FBC, TAS 201-94
5) Cyclic Wind Pressure Loading per FBC, TAS 203-94
6) Forced Entry Test, per FBC 2411.3.2.1 (b) and TAS 202-94
along with marked-up drawings and installation diagram of an aluminum window wall
system, prepared by Blackwater Testing, Inc., Test Report No. BT-ALD-15-005,
dated 10/28/15 and 02/23/16, both signed and sealed by Yamil Gerardo Kuri, P.E.
(Submitted under NOA No. 17-0201.04)
7. Test reports on: 1) Large Missile Impact Test per FBC, TAS 201-94
2) Cyclic Wind Pressure Loading per FBC, TAS 203-94
along with marked-up drawings and installation diagram of a window wall system,
prepared by Blackwater Testing, Inc., Test Report No. BT-ALD-15-008, dated
02/23/16, signed and sealed by Yamil Gerardo Kuri, P.E.
(Submitted under NOA No. 17-0201.04)
C. CALCULATIONS
1. Anchor verification calculations and structural analysis, complying with FBC 6th
Edition (2017), dated 09/24/19, prepared by Al-Farooq Corporation, signed and sealed
by Javad Ahmad, P.E.
(Submitted under NOA No. 19-1001.15)
2. Glazing complies with ASTM E1300-09.
Manuel Perez, P.E.
Product Control Examiner
NOA No. 20-0910.06
Expiration Date: July 03, 2024
Approval Date: November 12, 2020
E – 3
Aldora Aluminum & Glass Products, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
1. EVIDENCE SUBMITTED UNDER PREVIOUS NOA’s (CONTINUED)
D. QUALITY ASSURANCE
1. Miami-Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. Notice of Acceptance No. 17-0808.02 issued to Kuraray America, Inc. for their
“SentryGlas® (Clear and White) Glass Interlayers” dated 12/28/17, expiring on
07/04/23.
2. Notice of Acceptance No. 19-0221.01 issued to Allnex USA, Inc. for their “Uvekol®
S Laminated Glass Interlayer”, dated 03/28/19, expiring on 02/08/24.
3. Notice of Acceptance No. 17-0712.05 issued to Eastman Chemical Company (MA)
for their “Saflex Clear and Color Glass Interlayers” dated 09/07/17, expiring on
05/21/21.
F. STATEMENTS
1. Statement letter of conformance, complying with FBC 6th Edition (2017), and of no
financial interest, dated September 24, 2019, issued by Al-Farooq Corporation, signed
and sealed by Javad Ahmad, P.E.
(Submitted under NOA No. 19-1001.15)
2. Laboratory compliance letter for Test Reports No. BT-ALD-15-005, dated 10/28/15
and BT-ALD-15-008, dated 02/23/16, both issued by Blackwater Testing, Inc., both
signed and sealed by Yamil Gerardo Kuri, P.E.
(Submitted under NOA No. 17-0201.04)
3. Proposal No. 12-1644 issued by the Product Control Section, dated September 10,
2012, signed by Manuel Perez, P.E.
(Submitted under NOA No. 14-0415.06)
G. OTHERS
1. Notice of Acceptance No. 19-0124.06, issued to Aldora Aluminum & Glass Products,
Inc. for their Series “Front Set” Aluminum Window Wall System – L.M.I., approved
on 02/21/19 and expiring on 07/03/24.
Manuel Perez, P.E.
Product Control Examiner
NOA No. 20-0910.06
Expiration Date: July 03, 2024
Approval Date: November 12, 2020
E - 4
Aldora Aluminum & Glass Products, Inc.
NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED
2. NEW EVIDENCE SUBMITTED
A. DRAWINGS
1. Drawing No. W14-12, titled “Series Front Set Alum Window Wall Sys. (L.M.I.)”,
sheets 1, 1.1, 2, 3, 3.1, 4, 5, 6, 7, 7.1, 8, 9, 10, 10.1, 11, 11.1, 11.2, 11.3 and 12 through
19 of 19, dated 03/21/14, with revision E dated 06/25/20, prepared by Al-Farooq
Corporation, signed and sealed by Jalal Farooq, P.E.
B. TESTS
1. None.
C. CALCULATIONS
1. Anchor verification calculations and structural analysis, complying with FBC 5th
Edition (2014), dated 01/26/17, with FBC 6th Edition (2017), dated 10/24/17 and
updated on 07/22/20 to comply with FBC 7th Edition (2020), prepared by Al-Farooq
Corporation, signed and sealed by Jalal Farooq, P.E.
2. Glazing complies with ASTM E1300-09
D. QUALITY ASSURANCE
1. Miami-Dade Department of Regulatory and Economic Resources (RER)
E. MATERIAL CERTIFICATIONS
1. Notice of Acceptance No. 19-0305.02 issued to Kuraray America, Inc. for their
“Trosifol® Ultraclear, Clear and Color PVB Glass Interlayers” dated 05/09/19,
expiring on 07/08/24.
2. Notice of Acceptance No. 18-0725.11 issued to Kuraray America, Inc. for their
“Kuraray SentryGlas® XtraTM (SGXTM) Clear Glass Interlayer” dated 05/23/19,
expiring on 05/23/24.
F. STATEMENTS
1. Statement letter of conformance, complying with FBC 6th Edition (2017), with FBC 7th
Edition (2020) and of no financial interest, dated July 22, 2020, issued by Al-Farooq
Corporation, signed and sealed by Jalal Farooq, P.E.
G. OTHERS
1. Notice of Acceptance No. 19-1001.15, issued to Aldora Aluminum & Glass Products,
Inc. for their Series “Front Set” Aluminum Window Wall System – L.M.I., approved
on 11/27/19 and expiring on 07/03/24.
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020
Sealed: 09/09/2020