HomeMy WebLinkAboutEVALUATION REPORT POLYGLASS ROOF UNDERLAY MENTITPJNITYERD
EVALUATION REPORT
p— f--\ l :— twr r
EXTERIOR RESEARCH & DESIGN, LLC.
U2� Certificate of Authorization #9503
@@litGC 1 1 353 CHRISTIAN STREET, UNIT #13
PERMITTING PHONE:
CT 06478
St. Lucie County, FL PHONE: (203) 262-9245
FAX: (203) 262-9243
Polyglass USA, Inc. Evaluation Report P12060.02.09-R15
150 Lyon Drive I'1 (Z C �l� FL5259-RZO
Fernley, NV 98408 ST. LUCIE COUNTY BUILDENG n—M. SCIOti Date of Issuance: 02/24/2009
REVIEWED FOR COMPLIANCE Revision 15: 08/25/2014
REVIE:VED BY - -git2urJ=�-1�
SCOPE: DATE I't r1
OB
This Evaluation Report is issued % Tes and regulations governing the use of
construction materials in the Sta!ON160naffle I--n^�tktb%ted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been designed to comply with the Florida Building Code, 2010 sections noted herein.
DESCRIPTION: Polyglass Roof Underlayments
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product
changes or the referenced Quality Assurance documentation changes. Trinityl ERD requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity) ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation REnL�eROPt
THESE consists of
ARE SUBJECT TO ANY CORRECTIONS
Prepared by: REQUIRED BY FIELD INSPECTORS THAT
MAYBE NE ESSARY IN ORDER TO
WITH ALL APPLICABLE CODES.
Robert I.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DC4 ANE1983
CONCEALED FASTENERS OR ATTACHMENTS
ARE THE RESPONSIBILITY OF THE
CONTRACTOR OF RECORD
The facsimile seal appearing was authorized
by Robert Nleminen, P.E. on 08/25/2014
This does not serve as an electronically signed document.
Signed, sealed hardcoples have been transmitted to the
Product Approval Administrator and to the named client
CERTIFICATION OF INDEPENDENCE:
1. Trinityl ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. Trinityl ERD is not owned, operated or controlled by any company manufacturing or distributing products It evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will. acquire, a financial interest in any other entity involved in the approval process of the
product.
File Copy
ERD
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: Roof Underlayments, as produced by Polyglass USA, Inc., have demonstrated compliance with the
following sections of the Florida Building Code through testing in accordance with the following Standards. Compliance is subject
to the Installation Requirements and Limitations / Conditions of Use set forth herein.
2. STANDARDS:
Section
Property
Standard
Year
1507.2.3, 2507.3.3, 1507.5.3, 1507.7.3,
Physical Properties
ASTM D226
2006
1507.8.3,1507.9.3
1507.2.4, 1507.2.9.2, 1507.3.3,1507.5.3
Physical Properties
ASTM D1970
2001
1507.11.2
Physical Properties
ASTM D6164
2005
1507.11.2
Physical Properties
ASTM D6222
2002
1504.6
Accelerated Weathering
ASTM G154
2005
1504.6
Accelerated Weathering
ASTM G155
2005
1504.3.1
Wind Uplift
FM 4474
2004
1507.3.3
Installation Practice
FRSA/TRI 07320
2005
1523.6.5.2.1
Physical Properties
TAS 103
1995
3. REFERENCES:
Entity r
Examination
Reference
Date
FM Approvals (TST 1867)
Wind Uplift
3004091
01/12/2000
PRI (TST 5878)
Physical Properties
PRIO1111
04/08/2002
PRI (TST 5878)
Physical Properties
PUSA-005-02-01
01/32/2002
PRI (TST 5878)
Physical Properties
PUSA-013-02-01
12/23/2002
PRI (TST 5878)
Physical Properties
PUSA-013-02-02
12/23/2002
PRI (TST 5878)
Physical Properties
PUSA-013-02-03
12/23/2002
PRI (TST 5878)
Physical Properties
PUSA-018-02-01
07/14/2003
PRI (TST 5878)
Physical Properties
PUSA-028-02-01
07/13/2005
PRI (TST 5878)
Physical Properties
PUSA-033-02-01
01/12/2006
PRI (TST 5878)
Physical Properties
PUSA-035-02-01
09/29/2006
PRI (TST 5878)
PRI (TST 5878)
Physical Properties
PUSA-055-02-02
12/10/2007
PRI (TST 5878)
Physical Properties
Physical Properties
PUSA-061-02-02
PUSA-076-02-01
02/28/2008
PRI (TST 5878)
Physical Properties
PUSA-083-02-01
02/22/2008
04/14/2008
PRI (TST 5878)
Physical Properties
PUSA 088-02.01
07/29/2009
MTI (TST 2508)
Physical Properties
1X20H7A
04/01/2008
MTI (TST 2508)
Physical Properties
RX14E8A
01/29/2009
ERD (TST 6049)
Physical Properties
11752.09.99-1
02/08/2000
ERD (TST 6049)
Wind Uplift
11757.08.01-1
08/13/2001
ERD (TST 6049)
Wind Uplift
11776.66.02
01/16/2003
ERD (TST 6049)
ERD (TST 6049)
Physical Properties
02200.07.03
07/14/2003
ERD (TST 6049)
Wind Uplift
Physical Properties
P3740.01.07
P5110.04.07-1
01/04/2007
04/21/2007
ERD (TST 6049)
ERD (TST 6049)
Wind Uplift
P9260.03.08
03/21/2008
03/21/2008
ERD (TST 6049)
Physical Properties
Wind Uplift
P13450.08.09
ERD (TST 6049)
Physical Properties
P30540.11.09-111
P11030.11.09-1
12/30/2009
ERD (TST 6049)
Wind Uplift
P11030.11.09-2
il/30/2009
11/30/2009
ERD (TST 6049)
ERD (TST 6049)
Physical Properties
P11030.11.09-3
11/30/2009
ERD (TST 6049)
Physical Properties
Physical Properties
P33360.06.30
P33370.03.11
06/25/2010
ERD (TST 6049)
Physical Properties
P33370.04.11
03/02/2011
04/26/2011
ERD (TST 6049)
ERD (TST 6049)
Physical Properties
P37300.10.11
10/19/2011
ERD (TST 6049)
Physical Properties
Physical Properties
040390.08.12-1
08/06/2012
ERD (TST 6049)
Physical Properties
P40390.08.12-2
C41420.09.12-3
08/07/2012
09/11/2012
Exterior Research and Design, I.I.C. Evaluation Report P12060.02 09 R15 CertficateofAuthorizatlon 119503
FL5259-R20
Revision 15: 08/25/2014
Page 2 of 12
Y.
\
' !
�I
1
O Y , ERD
Enti
Examination
Reference
Date
ERD (TST 6049)
Wind Uplift
P39680.03.13
03/04/2013
ERD (TST 6049)
Physical Properties
P45370.04.13
04/26/2013
ERD (TST 6049)
Wind Uplift
P1738.02.07-R2
04/29/2013
ERD (TST 6049)
Wind Uplift
11757.04.01-1-R1
04/30/2013
ERD (TST 6649)
Wind Uplift
P41630.08.13
08/06/2013
ERD (TST 6049)
Wind Uplift
P11751.05.03-131
11/26/2013
ERD (TST 6049)
Wind Uplift
P11781.11.03-R1
11/26/2013
ERD (TST 6049)
Physical Properties
P45270.05.14
05/12/2014
ERD (TST 6049)
Physical Properties
P44360SC
05/15/2014
ERD (TST 6049)
Physical Properties
P46520.08.14
08/22/2014
ICC-ES (EVL 2396)
IBC Compliance
ESR-1697
09/01/2012
Miami -Dade (CER 1592)
HVHZ Compliance
NOA 12-0713.02
02/14/2013
Polyglass USA
Manufacturing Affidavit
Products Current
02/18/2009
Polyglass USA
P/L Affidavit
Mule -Hide Cross Ltg
03/01/2008
Polyglass USA
Materials Affidavit
Polystick SA Compound
08/18/2011
UL, LLC. (QUA9625)
Quality Control
Service Confirmation, R14571, 2Q4 Exp. 08/08/2015
UL, U.C. (QUA9625)
Quality Control
Service Confirmation, MTS PLUS Exp. 07/01/2017
4. PRODUCT DESCRIPTION:
4.1 Mechanically Fastened Underlavrr►ents:
4.1.1 Elastobase is a fiberglass reinforced, SBS modified bitumen base sheet.
4.1.2 Elastobase P is a polyester -reinforced, SBS modified bitumen base sheet.
4.2 _ Self-Adherin Underla ments:
4.2.1 �ip_olyoReflnlc
s a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, surfaced
film surface; meets ASTM D1970 and TAS 103.
4.2.2 Polystick MTS PLUS is a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced,
surfaced with poly -film surface; meets TAS 103.
4.2.3 Polystick IR-Xe is a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with an
aggregate surface; meets ASTM D1970.
4.2.4 PofystlekTU Pfs'fs a nominal 80-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with a
polyester fabric surface; meets ASTM D1970 and TAS 103.
4.2.5 Polystick TU P is a nominal 130-mil thick rubberized asphalt waterproofing membrane, glass-fiber/polyester reinforced,
with a granular surface; meets ASTM.D1970 and TAS 103.
4.2.6 Polystick TU Max is a nominal 60-mil thick rubberized asphalt waterproofing membrane with a 170 g/m2 polyester
fabric surface; meets TAS 103.
4.2.7 Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and Mule -Hide SA-APP Cap Sheet (FR) are polyester
reinforced, APP modified bitumen cap sheets.
4.2.8 Dual Pro'" is a nominal 60-mil thick dual -layer rubberized asphalt waterproofing membrane, fiberglass reinforced, with
a polyester fabric surface.
4.2.9 Tile Pro' is a nominal 60-mil thick dual -layer rubberized asphalt waterproofing membrane, fiberglass reinforced, with a
polyester fabric surface.
4.3 Mechanically Fastened and/or Bonded Underlayments•
4.3.1 Elastoflex S6 G and Elastoflex S6 G FR are polyester reinforced, SBS modified bitumen cap sheets.
4.3.2 Polyflex G and Polyflex G FR are polyester reinforced, APP modified bitumen cap sheets.
S. LIMITATIONS:
5.1 This Evaluation Report is not for use in the HVHZ.
5.2 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire
ratings of this product.
Exterior Research and Design, LLC. Evaluation Report P12060.02.09-1115
Certificate of Authorization #9503 FL5259-R20
Revision 1S: 08/25/2014
Page 3 of 11
5.3 Polyglass Roof Underlayments may be used with any prepared roof cover where the product is specifically referenced
within FBC approval documents. If not listed, a request may be made to the AHJ for approval based on this evaluation
combined with supporting data for the prepared roof covering.
5.4 Allowable roof covers applied atop the underlayments are as follows:
_ .. .
...,_.Wood
Shakes &..:.
Underlayment Asphaltshingles Nail -On Tile Foam -On Tile Metal Slate
Shingles
i Elastobase
Yes
Yes
No
Yes
Yes
Yes
Elastobase P
Yes
Yes
No
Yes
Yes
Yes
Polystick MTS
Yes
Yes
No
Yes
Yes
Yes
Polystick MTS PLUS
Yes
Yes
No
Yes
Yes
Yes
Polystick IR-Xe
Yes
No
No
No
Yes
Yes
Polystick TU P
Yes
Yes
Yes
No
Yes
Yes
See 5.4.1
PotysUckSUPJus ` ;*
Yes
Yes
Yes
See 5.4.1
Yes
Yes
Polystick TU Max
No
Yes
Yes
Yes
No
No
See 5.4.1
Dual Pro
Yes
Yes
No
Yes
Yes
Yes
Tile Pro
Yes
Yes
Yes
Yes
Yes
Yes
See 5.4.1
Elastoflex S6 G
Yes
Yes
Yes
No
Yes
Yes
See 5.4.1
Elastoflex S6 G FR
Yes
Yes
No
No
Yes
Yes
Polyflex G
Yes
Yes
Yes
No
Yes
Yes
See 5.4.1
Polyflex G FR
Yes
Yes
No
No
Yes
Yes
Polyflex SAP or SAP FR
Yes
Yes
Yes
No
Yes
Yes
See 5.4.1
Mule -Hide SA-APP Cap Sheet or SA-
Yes
APP Cap Sheet(FRI
Yes
Yes
See 5.4.1
No
Yes
Yes
5.4.1 "Foam -On Tile" is limited to use of the following Approved the adhesives unless tensile adhesion / long term aging
data from an accredited testing laboratory is provided.
✓ 3M— 2-Component Roof Tile Adhesive AH-160 (formerly Polyfoom PolyPro AH260): Polystick TU P, Polystick TU
Plus, Polystick TU'Max, Elastoflex S6 G, Polyflex G, Polyflex SAP, Polyflex SA Cap FR, Mule -Hide SA-APP Cap Sheet
or Mule -Hide SA-APP Cap Sheet (FR) or Tile Pro.
✓ 3M— Foam Roof Tile Adhesive RTA-1: Polystick TU P, Polystick TU Plus, Polystick TU Max, Elastoflex S6 G, Polyflex
G, Polyflex SAP, Polyflex SA Cap FR, Mule -Hide SA-APP Cap Sheet or Mule -Hide SA-APP Cap Sheet (FR) or Tile Pro
✓ Dow TileBond: Polystick TU P, Polystick TU Plus, Polyflex SAP or Tile Pro
✓ Convenience Products' Touch 'n Seal StormBond Roof Tile Adhesive: Polystick TU Plus, Polystick TU Max
5.5 Allowable substrates are noted below:
Exterior Research and Design, I.I.C. Evaluation Report 1212060.02.09-1115
Certificate oJAuthorization #9503 FL5259-R20
Revision 15; 08/25/2014
Page 4 of 11
TP
5.5.1 Direct -Bond to Deck:
Polystick (all variations), Dual Pro, Tile Pro, Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet
(FR) self -adhered to:
D New untreated plywood; ASTM D41 primed new untreated plywood; Existing plywood; ASTM D41 primed existing
plywood; New or existing, unprimed OSS; ASTM D41 primed OSB; Southern Yellow Pine; ASTM D41 primed Southern
Yellow Pine; ASTM D41 primed structural concrete; Huber Engineered Woods "ZIP System" Panels (designed and installed
to meet wind loads for project).
Note: Polyglass does not require priming of new or existing plywood or OSB sheathing. New or existing plywood or OSB
sheathing should be cleaned of all dirt and debris prior to application of Polystick membranes.
Elastoflex S6 G or S6 G FR in hot asphalt to:
D ASTM D41 primed structural concrete.
Polyflex G or G FR torch -applied to:
ASTM D41 primed structural concrete.
5.5.2 Bond -to -Insulation:
Polystick, Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) self -adhered to:
Y ASTM C1289, Type II, Class 1 polyisocyanurate or Type V polyisocyanurate-composite insulation; Dens Deck DuraGuard;
Dens Deck Prime; or SECUROCK Gypsum -Fiber Roof Board.
Elastoflex 56 G or S6 G FR in hot asphalt to:
D Dens Deck Prime or SECUROCK Gypsum -Fiber Roof Board.
Polyflex G or G FR torch -applied to:
D ASTM D41 primed structural concrete; Dens Deck Prime or SECUROCK Gypsum -Fiber Roof Board.
For installation under mechanically attached prepared roof coverings, insulation shall be attached per minimum
requirements of the prepared roof covering manufacturer's Product Approval. For installations under foam -on tile
systems, insulation attachment shall be designed by a qualified design professional and installed based on testing of
the insulatio6/underiayment system in accordance with FM 4470, Appendix K orTAS 114, Appendix J.
5.5.3 Bond to Mechanically Attached Base Laver:
Polystick, Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) Dual -Pro or Tile Pro self -
adhered to:
D ASTM D226, Type I or II felt; Elastobase; Elastobase P or Mule -Hide Nail Base.
Elastoflex S6 G or S6 G FR in hot asphalt to:
D ASTM D226, Type I or II felt; Elastobase; Elastobase,P or Mule -Hide Nail Base.
Polyflex G or G FR torch -applied to:
D Elastobase; Elastobase P or Mule -Hide Nail Base.
For installations under mechanically attached prepared roof coverings, base layer shall be attached per minimum
codified requirements. For installations under foam -on tile systems, refer to Section 5.5.4 herein and FRSA/TRI
07320/8-05 or RAS 120.
5.5.4 Wind Resistance for Underlavment Systems in Foam -On Tile Applications: FRSA/TRI 07320 does not address wind
uplift resistance of all underlayment systems beneath foam -on tile systems, where the underlayment forms part of the
load -path. The following wind uplift limitations apply to underlayment systems that are not addressed in FRSA/TRI
07320 and are used in foam -on tile applications. Maximum Design Pressure is the result of testing for wind load
resistance based on allowable wind loads. Refer to FBC 1609.1.5 for determination of design wind pressures.
5.5.4.1 Maximum Design Pressure = -90 osf.
Deck: Min.15/32-inch plywood to meet project requirements to satisfaction of AHJ.
Primer: (Optional) ASTM D41
Underlayment: Polystick TU P, Polystick TU Plus, Polyflex SAP, PolyFlex SAP FR, Mule -Hide SA-APP Cap Sheet and Mule -Hide SA-APP
Cap Sheet (FR), self -adhered.
Exterior Research and Design, LLC. Evaluation Report P12060.02.09-1115
Certificate ofAuthorization #9503 FL5259-R20
Revision 15: 08/25/2014
Page 5 of 11