HomeMy WebLinkAboutNOA1�IK�I�iJFiLJC i
-
MIANII-DARE COUNTY
PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE (NOA)
www.miamidade.gov/economy
Polyglass USA, Inc.
150 Lyon Drive
Fernley, NV 89408
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date.stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: Polyglass Self -Adhered Roof System over Wood Decks
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwisenoted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section.
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA# 13-1217.01 and consists of pages 1 through 34.
The submitted documentation was reviewed by Alex Tigera.
File Copy
... ..A
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 1 of 34
11
ROOFING ASSEMBLY APPROVAL
Category
Roofing
Sub -Category:
Modified Bitumen
Materials
SBS/APP/TPO
Deck Type:
Wood
Maximum Design Pressure
-112.5 psf
TRADE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE I
Test - Product
Product'" Dimensions Specification Description
Elastobase 65' 2" x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Type I base sheet.
XtraFlex SBS Glass 65' 8" x 3' 3-3/8" ASTM D 6163, SBS modified asphalt coated fiberglass reinforced
Base
Type I
base sheet.
Polyglass G2 Base
108' x 36"
ASTM D 4601
Asphalt -coated fiberglass reinforced base sheet
Type H
Polyanchor
250' x 48"
ASTM D 4601
A polymer woven, high performance, synthetic base
Type H
sheet.
Elastobase P
65' 8" x 3' 3-3/8"
ASTM D 6164,
SBS modified asphalt coated polyester reinforced base
Type I
sheet.
Elastoflex SA V FR
66' 8" x 3' 3-3/8"
ASTM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
(1.5-nun)
Type I _
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
Elastoflex SA V
66' 8" x 3' 3-3/8"
ASTM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
PLUS FR
Type I
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
Elastoflex SA V (1.5-
66' 8" x 3' 33/8"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
mm)
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
Elastoflex SA V
66' 8" x 3' 3 3/s"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
PLUS
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
XtraFlex SBS Base
66' 8" x 3' 3 3/s"
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
SA
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
r Elastoflex SA P FR
32' 10" x 3' 3-3/8"
ASTM D 6164,
Self -adhered, fire -rated, polyester reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
XtraFlex SBS G SA
32' 10" x 3' 3-3/8"
ASTM D 6164,
Self -adhered, fire -rated, polyester reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
NOA No.: 17-1004.09
MIAMI•DAD; COUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 2 of 34
lElastoflex SAP 32' 10" x 3' 3-3/8" ASTM D 6164, Self -adhered, fiberglass reinforced, SBS modified
Type I bitumen membrane with a self -adhering back face and
a granule top surface.
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
Torch applied, polyester reinforced, APP modified
bitumen membrane with a bum off polyethylene back
face and a smooth or sanded top surface.
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a granule top surface.
Self -adhered, polyester reinforced, APP modified
bitumen membrane with a self -adhering back face and
a granule top surface.
Self -adhered; fire -rated, polyester reinforced, APP
modified bitumen membrane with a self -adhering back
face and a granule top surface.
XtraFlex APP G SA 32' 10" x 3' 3 3/8"
ASTM D 6222,
Self -adhered, fire -rated, polyester reinforced, APP
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polyfresko G SBS SA 32' 10" x 3' 3 3/s"
ASTM D 6164,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back face and
a granule top surface.
Polyfresko G SBS SA 32' 10" x Y 3 3/s"
ASTM D 6164,
Self -adhered, fire -rated, fiberglass reinforced, SBS
FR
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Polyfresko G APP SA 32' 10" x 3' 33/8"
ASTM D 6222,
Self -adhered, polyester reinforced, APP modified
Type I
bitumen membrane with a self -adhering back face and
a granule top surface.
Polyfresko G APP SA 32' 10" x 3' 33/s"
ASTM D 6222,
Self -adhered, fire -rated, polyester reinforced, APP
FR
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface
PolyKool 32' 10" x 3' 3 3/s" ASTM D6222 Self -adhered, polyester reinforced, APP modified
Type I bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
XtraFlex Kool APP S 32' 10" x 3' 33/s" ASTM D6222 Self -adhered, polyester reinforced, APP modified
SA Type I bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
Polyglass APP Base 65' 8" x 3' 33/8" ASTM D 6509 APP modified asphalt coated fiberglass reinforced
Type I base sheet.
NOA No.: 17-1004.09
Muathtiaaoe couNr�r Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 3 of 34
Polyflex
32'
10"
x 3'
3-3/8"
ASTM D 6222
XtraFlex APP S
32'
10"
x 3'
3-3/8"
ASTM D 6222
Polybond
32'
10"
x 3'
3-3/8"
ASTM D 6222
Polyflex G
32'
10"
x 3'
3-3/8"
ASTM D 6222
Polyflex SA P
32'
10"
x 3'
3 3/s"
ASTM D 6222,
Type I
Polyflex SA P FR
32'
10"
x 3'
3 3/s"
ASTM D 6222,
Type I
PG325 Cold Process
Adhesive
PG100 Asphalt Primer
XtraFlex 10 Asphalt
Primer
PG350 Mod Bit
Adhesive
PG400 Plastic Roof
Cement
PG425 Wet/Dry Roof
Cement
PG450 Flashing
Cement
PG500 MB Flashing
Cement
Polyplus 35 Premium
Mod Bit Adhesive
XtraFlex 35 Premium
Mod Bit Adhesive
Polyplus 45 Premium
Flashing Cement
Polyplus 50 Premium
MB Flashing Cement
XtraFlex 50 Premium
Modified Wet/Dry
Cement
Polyplus 55 Premium
Modified Flashing
Cement
MAMFDADE COUNTY
�1201-57151
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal,
tube or 17 oz. spray
can
1, 3, 5, 50, 55 gal,
tube or 17 oz. spray
can
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
ASTM D3019 A fibered cold process adhesive for use with roll or
Type III BUR roofing.
ASTM D41 A penetrating solution of solvent and a blend of
selected asphalts used to promote adhesion.
ASTM D41 A penetrating solution of solvent and a blend of
selected asphalts used to promote adhesion.
ASTM D3019 A fibered rubberized adhesive designed for use with
Type III modified bitumen membranes.
ASTM D4586 A thick, fibered, rubberized flashing cement for use in
ASTM D3409 dry or damp conditions.
ASTM D4586 A thick, fibered, rubberized flashing cement for use in
ASTM D3409 dry or damp conditions.
ASTM D4586 A thick, fibered, rubberized flashing cement.
ASTM D4586
A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
ASTM D3019
A fibered rubberized adhesive designed for use with
Type III
modified bitumen membranes.
ASTM D3019
A fibered rubberized adhesive designed for use with
Type III
modified bitumen membranes.
ASTM D4586
A thick, fibered, rubberized flashing cement.
ASTM D4586 A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
ASTM D4586 A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
1, 3, 5, 50, 55 gal. or ASTM D4586 A mastic compound for use as a roof flashing
tube adhesive.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 4 of 34
APPROVED INSULATIONS:
TABLE 2
Product Name Product Description
Polytherm-H
Polyisocyanurate foam insulation
Polytherm
Polyisocyanurate foam insulation
ACFoam-II
Polyisocyanurate foam insulation
ACFoam-III
Polyisocyanurate foam insulation
High Density Wood Fiberboard
Wood fiber insulation board
DensDeck, DensDeck Prime
Gypsum insulation board
H-Shield
Polyisocyanurate foam insulation
H-Shield CG
Polyisocyanurate/perlite composite insulation
ENRGY-3
Polyisocyanurate foam insulation
Fesco Board
Expanded mineral fiber
Multi -Max FA-3
Polyisocyanurate foam insulation
SECUROCK Gypsum -Fiber Roof Board
Fiber reinforced coverboard
Manufacturer
ith Current NOA
Polyglass USA, Inc.
Polyglass USA, Inc.
Atlas Roofing Corp
Atlas Roofing Corp
Generic
Georgia-Pacific Gypsum LLC
Hunter Panels, LLC
Hunter Panels, LLC
Johns Manville Corp.
Johns Manville Corp.
Rmax Operating, LLC.
United States Gypsum
Corporation
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 5 of 34
I
APPROVED FASTENERS:
TABLE 3
Fastener
Product
Product
Manufacturer
Number
Name
Description
Dimensions
(With Current NOA)
1.
Dekfast Fasteners 12, 14 &
Insulation fastener for wood,
SFS Intec, Inc.
15 HS
steel and concrete decks
2.
Dekfast Galvalume Steel
Galvalume hex stress plate.
2'/8" x
SFS Intec, Inc.
Hex Plate
3 1/4"
3.
#14 Roofgdp
Insulation and membrane
Various
OMG, Inc.
fastener
4.
Flat Bottom Metal Plate
A2-SS aluminized steel plate
3" square
OMG, Inc.
5.
Trufast #14 HD Fastener
Insulation fastener for steel and
Altenloh, Brinck & Co.
wood decks
U.S., Inc.
6.
Trufast 3" Metal Insulation
Round Galvalume AZ50 steel
3.23 round
Altenloh; Brinck & Co.
Plate
plate
3" round
U.S., Inc.
7.
Polygrip Fasteners #12, #14
Insulation fastener for wood,
Various
Polyglass USA, Inc
& #15
steel and concrete decks
8.
Polygrip Hex Plates
Galvalume hex stress plate.
27/8" x
Polyglass USA, Inc
3 I/4»
r
NOA No.: 17-1004.09
MIAWDAD, COUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 6 of 34
APPROVED SURFACING:
TABLE 4
Product Product
Name Description
PG200 Non-Fibered Roof Coating A non fibered asphaltic coating used
to add life and rejuvenate existing
BUR roofing substrates.
XtraFlex 20 Bituminous Roof A non fibered asphaltic coating used
Coating to add life and rejuvenate existing
BUR roofing substrates.
PG300 Fibered Roof Coating An asphalt cutback fibered roof
coating. May be applied by brush or
spray equipment to rejuvenate aged
BUR
Application
Rate
11/z-2, gaUsq
11/z-2 gaUsq
Specification
Manufactur
er
TAS 140
Polyglass
USA, Inc.
TAS 140
Polyglass
USA, Inc.
1%-2 gaUsq ASTM D4479 Polyglass
USA, Inc.
XtraFlex Bituminous Roof
An asphalt cutback fibered roof
1 %Z-2 gaUsq
ASTM D4479
Polyglass
Coating Fibered
coating. May be applied by brush or
USA, Inc.
spray equipment to rejuvenate aged
BUR
PG600 Non-Fibered Aluminum
Non-fibered aluminum roof coating.
%2-1 gaUsq
ASTM D2824
Polyglass
Roof Coating
Type I
USA, Inc.
PG650 Fibered Aluminum Roof
Fibered aluminum roof coating.
1 %z-2 gaUsq
ASTM D2824
Polyglass
Coating
Type III
USA, Inc.
PG700 Elastomeric Roof Coating
A premium white elastomeric acrylic
1-1 %2 gaUsq
' ASTM D6083
Polyglass
based roof coating (water -based). A
USA, Inc.
polyester fabric may be used for
reinforcement with this coating.
PG800 Non-Fibered Asphalt
An asphalt base, un-fibered clay
3 gaUsq in
ASTM D1227
Polyglass
Emulsion Roof Coating
emulsion
two coats
USA, Inc.
XtraFlex 80 Emulsion Roof
An asphalt base, un-fibered clay
3 gaUsq in
ASTM D1227
Polyglass
Coating
emulsion
two coats
USA, Inc.
PG850 Fibered Asphalt Emulsion
An asphalt base, fibered clay
3 gaUsq in
ASTM D1227
Polyglass
Roof Coating
emulsion
two coats
USA, Inc.
Polyplus 65 Premium Fibered
Fibered aluminum roof coating.
1 %Z-2 gaUsq
ASTM D2824
Polyglass
Aluminum Roof Coating
Type III
USA, Inc.
XtraFlex 65 Aluminum Roof
Fibered aluminum roof coating.
11/2-2 gaUsq
ASTM D2824
Polyglass
Coating Fibered
Type III
USA, Inc.
Polyplus 60 Premium Non-
Non-fibered aluminum roof coating.
%Z-1 gaUsq
ASTM D2824
Polyglass
Fibered Aluminum Roof Coating
Type I
USA, Inc.
XtraFlex 60 Aluminum Roof
Non-fibered aluminum roof coating.
%-1 gaUsq
ASTM D2824
Polyglass
Coating
Type I
USA, Inc.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 7 of 34
APPROVED SURFACING:
TABLE 4
Product
Product
Name
Description
Polybrite 70 Premium Grade
A premium white elastomeric acrylic
Elastomeric Roof Coating
based roof coating (water -based). A
polyester fabric may be used for
reinforcement with this coating.
XtraFlex 70 Premium Acrylic FR
A premium white elastomeric acrylic
Roof Coating
based roof coating (water -based). A
polyester fabric may be used for
reinforcement with this coating.
Polybrite 90 High Solids Silicone
A premium grade high solids, single
Roof Coating
component, moisture cure, fluid
applied silicone coating
XtraFlex SRC 9600 High Solids
A premium grade high solids, single
Silicone Roof Coating
component, moisture cure, fluid
applied silicone coating
Polybrite 95 Silicone Roof
A single component, solvent,
Coating
moisture cure silicone coating.
XtraFlex SRC 8000 Silicone Roof
A single component, solvent,
Coating
moisture cure silicone coating.
Gravel
To be installed in a flood coat of
approved asphalt at 60 lbs/sq
Slag
To be installed in a flood coat of
approved asphalt at 601bs/sq
Application Specification
Rate
1-1%2 gaUsq ASTM D6083
1-1% gaUsq ASTM D6083
Manufactur
er
Polyglass
USA, Inc.
Polyglass
USA, Inc.
1.25 gaUsq ASTM D6694 Polyglass
USA, Inc.
1.25 gaUsq ASTM D6694 Polyglass
USA, Inc.
1.25 gaUsq ASTM D6694 Polyglass
USA, Inc.
1.25 gaUsq ASTM D6694 Polyglass
USA, Inc.
4001bs/sq N/A Generic
300lbs/sq N/A Generic
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 8 of 34
EVIDENCE SUBMITTED:
Test Agency
Test Name/Report
Report No.
Date
Factory Mutual Research
4470
2W7A7.AM
08.04.94
Corporation
4450
2D5A9.AM
06.22.99
4470
3001334
02.15.00
4470
3000857
01.12.00
4470
3004091
01.12.00
4470
3012321
07.29.07
4450
3014751
08.27.03
4450
3019317
06.30.04
4470
3014692
08.05.03
Trinity ERD
TAS 114
11752.09.99-1
02.08.00
TAS 114'
02764.09.05
09.09.05
TAS 114
02762.03.05
03.30.05
TAS 117(B)-ASTM D903
020841.06.04
06.02.04
TAS 114
P1734.07.06-R1
02.27.07
TAS 114
P1738.02.07
02.05.07
TAS 114
P1739.01.07
01.23.07
TAS 117(B)-ASTM D6862
C8500SC.11.07
11.30.07
ASTM D6164 / ASTM D6222
P 10490.08.08
08.13.08
ASTM D6164 / ASTM D6222
P 10490.10.08-R1
10.03.08
ASTM D6222
P7400.03.08-R2
10.09.08
TAS 114(D) — ASTM D 1876
P 10070.10.08
10.09.08
ASTM D6222
P10490.10.08-2
10.30.08
FM 4470 & TAS 114
P33970.03.11
03.15.11
ASTM D6163 / ASTM D 4601
P33960.03.11
03.15.11
TAS 114 & TAS 117 (B)
11757.12.00-1-R1
04.29.13
TAS 114 & TAS 117 (B)
11757.04.01-1-R1
04.30.13
ASTM D6164
P37590.07.13-1
07.02.13
ASTM D6164
P37590.03.13-3A
03.06.13
ASTM D6163
P37590.03.13-2-R1
02.05.13
ASTM D6222
P37590.09.13
09.12.13
ASTM D4601 / TAS 117
P45940.09.13
09.04.13
TAS 114 & FM 4474
P41630.08.13
08.06.13
TAS 114 (IT)
P13760.09.09
09.10.09
ASTM D4601 / TAS 117
P45970.05.14
05.12.14
PRI Construction Materials
ASTM D6222
PUSA-061-02-02
01.28.08
Technologies
ASTM D6222
PUSA-062-02-02
12.04.08
ASTM D6163
PUSA-064-02-02
02.27.08
ASTM D6694
PUSA-134-02-01
05.16.14
ASTM D6694
PUSA-135-02-01
05.16.14
NOA No.: 17-1004.09
Expiration Date:, 10/11/22
Approval Date: 10/12/17
Page 9 of 34
APPROVED ASSEMBLIES:
Membrane Type: SBS/APP
Deck Type II: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c..
System Type A(1): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Polyglass G2 Base, Polyflex*, XtraFlex APP
S*, Polybond* or GAFGLAS #75 fastened to the deck as described below:
*with OMG fasteners and Flat Bottom Metal Plates.
Fastening #1: Attach base sheet using 11 ga. annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c.
in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Fastening #2: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
14 with Galvalume Steel Hex Plates or Polygrip Fasteners #14 with Polygrip Hex Plates or
Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap
and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick
N/A
N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 2040 Ibs/100 ff. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/W
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/a" thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 20-40 lbs/100 ftz. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 10 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP SA, Polyflex SA. P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See general limitation V.)
NOA No.: 17-1004.09
Mu�rn•oane couNr�r Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 11 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P, Polyglass G2 Base, Polyflex,
XtraFlex APP S or Polybond fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 31 Density/fe
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick N/A N/A
Top Insulation Laver Insulation Fasteners, Fastener
Table 3 Density/ft2
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum V thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 2040 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 12 of 34
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -60 psf; (See general limitation V.)
r
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 13 of 34
Membrane Type: SBS/APP
Deck Type II: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type A(3): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below:
Fastening: Attach base sheet using 11 ga. Annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c.
in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
One of more of the following:
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/fe
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top Insulation Laver Insulation Fasteners Fastener
able 3 Density/fe
Dens Deck, Dens Deck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum %11 thick N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of 2040 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 14 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See general limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 15 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank fastened at 24" spans with #8 wood screws at 6" o.c.
System Type A(4): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened as below:
Fastening: 12 ga. Annular ring shank nails and 1-5/8" tin -caps attached 6" o.c. in 4" lap and 6" o.c. in four
equally spaced staggered rows.
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/fe
ACFoam-H, Polytherm, ACFoam-III, H-Shield, Polytherm-H, H-Shield CG, Multi -Max FA-3, ENRGY 3
Minimum 1" thick N/A N/A
Note: All insulation shall be adhered to the anchor sheet with Millennium One -Step Foamable Adhesive applied
over rows of tin -caps in continuous rows 7" o.c. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet:
One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane:
One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing:
(Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-60 psf; (See general limitation V.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 16 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with 8d common nails or wood
screws at 4" o.c.
System Type C(1): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1.5" thick
Insulation Fasteners Fastener
able 3 Densi /ft'
N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Ton Insulation Laver
Approved High Density Wood Fiberboard
Minimum'/" thick
DensDeck
Minimum'/" thick
Insulation Fasteners Fastener
Table 3 Density/ftz
1:1.33 ft2
1 1:1.33 ftz
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 17 of 34
coating or required fire classification.
Maximum Design
Pressure: -67.5 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 18 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
System Type C(2): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1.51' thick
Insulation Fasteners Fastener
able 3 Density/fe
N/A N/A
Note: All layers shall be simultaneously fastened; see top layer below for fasteners and density. Insulation
panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners shall be
increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS 117 for
insulation attachment.
Top Insulation Laver
Approved High Density Wood Fiberboard
Minimum'/" thick
DensDeck
Minimum V4" thick
Insulation Fasteners Fastener
Table 3 Density/fe
1:1.33 ft2
1:1.33 W
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-min) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SSA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 19 of 34
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -67.5 psf; (See General limitation V.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 20 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with wood screws at 6" o.c.
System Type C(3): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following:
Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
ENRGY 3, H-Shield, Polytherm-H, ACFoam-II, Polytherm
Minimum 1.5" thick 1, 5 or 7 1:1.33 ft2
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -82.5 psf; (See General limitation V.)
NOA No.: 17-1004.09
MAMI-oaoe couNr�r Expiration Date: 10/11/22
�UawayzlApproval Date: 10/12/17
Page 21 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type D(1): All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick
Ton Insulation Laver (Optional)
Fesco Board
Minimum %" thick
Approved High Density Wood Fiberboard
Minimum'/" thick
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum V thick
Insulation Fasteners Fastener
able 3 Density/ft'
N/A N/A
Insulation Fasteners Fastener
Table 3 Density/ft'
N/A N/A
N/A N/A
N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One or more plies of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor
fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners #14 with Polygrip Hex Plates
or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap
and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
NOA No.: 17-1004.09
Muu�tioa �Fjmteyjgj rr Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 22 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 23 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type D(2): All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened through insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick
Top Insulation Laver (Optional)
Fesco Board
Minimum %11 thick
Approved High Density Wood Fiberboard
Minimum %11 thick
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum %" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Insulation Fasteners Fastener
Table 3 Density/ft'
N/A N/A
N/A N/A
N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board having no dimension greater than 8 ft.
Base Sheet: One or more plies of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor
fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FP, self -adhered.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 24 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -60 psf; (See General limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 25 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type E(1): Base sheet is mechanically attached to roof deck.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General limitation V.).
1NTY NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 26 of 34
Membrane Type:
Deck Type 1:
SBS/APP
Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type E(2): Base sheet is mechanically attached to roof deck.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening #: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
#14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners #14 with Polygrip Hex
Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a
4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -60 psf; (See General limitation V.).
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 27 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d ring shank nails at 6"
o.c. at edges and intermediate supports.
System Type E(3): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Polyglass APP Base, Elastobase (Poly/Sand) sheet fastened to the deck as described
below:
Fastening: Attach base sheet using 11 ga. annular grooved shank and 1" diameter caps spaced 6" o.c. in a
3" lap and 6" o.c. in four equally spaced staggered center rows.
Membrane: One ply of Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyfresko G SBS SA,
Polyfresko G SBS SA FR, Polyflex SA P, Polyflex SA P FR, XtraFlex APP G SA, Polyfresko
G APP SA, Polyfresko G APP SA FR, PolyKool or XtraFlex Kool APP S SA self -adhered.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General Limitation #7)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 28 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c
System Type E(4): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation. i
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet:
One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening:
Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet:
One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane:
One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -adhered.
Or
One ply of Polyflex G, torch -applied
Surfacing:
(Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf; (See General Limitation #7)
' NOA No.: 17-1004.09
aMLA,WDMDEC0U=NTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 29 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
or #8 wood screws at 6" o.c.
System Type E(5): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet:
One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening:
Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet:
One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane:
One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -adhered.
Or
One ply of Polyflex G, torch -applied
Surfacing:
(Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure:
-52.5 psf, (See General Limitation #7)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 30 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32' or greater plywood or wood plank, fastened to supports spaced 24" o.c. and to blocking
members spaced-48" o.c. with TruFast TP #10x2-7/8" screws spaced 6" o.c.
System Type E(6): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 4"
o.c. in a 4" lap and 4" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Elastoflex SA P, Elastoflex SA P
FR or XtraFlex SBS G SA, self -adhered.
Or
One ply of Polyflex G, torch -applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -97.5 psf; (See General Limitation #7)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 31 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. and to blocking
members spaced 48" o.c. with #100" wood screws spaced 6" o.c.
System Type E(7): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: Attach base sheet using 12 ga. ring shank nails and tin caps spaced 4" o.c. in a 4" lap and 4"
o.c. in four equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Elastoflex SA P, Elastoflex SA P
FR or XtraFlex SBS G SA, self -adhered.
Or
One ply of Polyflex G, torch -applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -112.5 psf; With Elastoflex SA V PLUS, XtraFlex SBS Base SA or Elastoflex SA V PLUS FR
(See General limitation #7.)
-97.5 psf; With Elastoflex SA V(1.5-mm) or Elastoflex SA V FR(1.5-mm) (See General
limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 32 of 34
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or wood plank, fastened to supports spaced 24" o.c. with #8x3" wood
screws spaced 6" o.c.
System Type E(8): Base sheet is mechanically attached to roof deck. Membranes subsequently adhered to
insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida. Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: 12 ga. annular ring shanked nails and 1-5/8" tin -caps 6" o.c. in 4" lap and 6" o.c. in four equally
spaced staggered rows. Tin -caps are primed with PG100 Asphalt Primer or XtraFlex 10
Asphalt Primer.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -adhered.
Or
One ply of Polyflex G, torch -applied
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -112.5 psf; With Elastoflex SA V PLUS, XtraFlex SBS Base SA or Elastoflex SA V PLUS FR
(See General limitation #7.)
-97.5 psf; With Elastoflex SA V(1.5-mm) or Elastoflex SA V FR(1.5-mm) (See General
limitation #7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 33 of 34
WOOD DECK SYSTEM LIMITATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product
Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the
top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam
insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using
spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one
at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 121bs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F) value of 2751bf., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener
spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or
Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal
resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing
Application Standard RAS 117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
_ Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS 111 and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended comers and comers). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 34 of 34