HomeMy WebLinkAboutPRODUCT EVALUATION REPORT 5V CRIMP ROOF11;57wnlast Metals
Value Engineered Meta/ Roofing n"
KEY WEST�SERLES (5='V CRIMP)
26 GA.- 24 RO'OF PANEL OVER 15132"`PLYW00D'
,:A RIDA PRODUCT APPROVAL NO 21423.7
Product Evaluation Report
26GA 5 V CRIMP Roof Panel over 15/32" Plywood
Florida Product Approval #21423.7
Florida Building Code 2014 Per Rule 61G20-3
Method: i —D
Category: Roofing Subcategory: Metal Roofing Compliance Method:
Rule 61G20-3
HVHZ
Product Manufacturer:
sunlast Metal'
2120 SW Poma Drive
Palm City, Florida 34990
Engineer Evaluator
James Biagi, P.E. FL # 37467
1915 NE 451' ST. #107
Fort Lauderdale, FL 33308
954-776-8004
Validator:
Locke Bowden, P.E., FL #49704
9450 Alysbury Place
Montgomery, AL 36117
Evaluation Report 1-4
i
at,,:t4tfCr,.Erf�-
,; F. F1.�%��
fameNiWa 7- '
FL#376�Z
seSTATE OF
"'IFS .•, �R.pF,-,.•\\�<c.+�:
fir. S� � X.��
��A1'�
Page 1 of 4
Compliance Statement: The product as described in this report has demonstrated compliance with the
Florida Building Code 2014, Sections 1504.3.2, 1507.4.3, 1518.9, 1523.6.5.2.4
Product Description: 26GA 5 V Crimp Metal Panel, 24" Width, Roof panels, 5/8" Rib height,12" O.C.
Panel THRU FASTENED into 15/32" APA Plywood decking. Non-structural Application.
FOR USE IN HVHZ.
Material: 26GA metal conforming to Florida Building Code 2014 Section 1507.4.3 Yield Strength: 55KSI
Corrosion Resistance: Panel Material shall comply with Florida Building Code 2014, Section 1507.4.3
Panel Dimensions: Panel Width: 24" width
Fastener: Wood-Zac XG fastener w/Neoprene washer or equivalent #10 Hex Head. Corrosion Resistant per Florida Building
Code 2014 Section 1506.7
3/16" minimum penetration through plywood
Corrosion Resistance: Per Florida Building Code 2014, Section 1506.6,1507.4.4
15/32" APA plywood, plywood supports at maximum 24' O.C. Design of plywood and plywood supports are outside the scope of
this evaluation. Must be designed in accordance w/ Florida Building Code 2014.
nneit:n I Inlift Dmeenroe• I Inlift r)Pcion PrPvmrP- with Safety Factor of 2
-•o• mot-•
TABLE A
-r• __________________
_____
Roof Areas
Field
Perimeter/Corner
Max Design Pressure
-78.5psf
-189.25psf
Fastener Spacing
16" o.c.
8" o.c.
Fastener Size
#10
# 10
Insulation: Optional Rigid Insulation board, 3" max thickness compliant with FBC 2014 section 1508.2
Quality Assurance: In accordance with FBC 2024 and Rule # 61620-3: Keystone Certification,
Inc. QUA 2824
Test References:
Architectural Testing Inc (TST 1527) # F0755.01-450-18 TAS 125-2003
Architectural Testing Inc (TST 1527) #0412-1017-05 TAS 125-2003
Architectural Testing Inc. (TST 1527)# SFMS-001-02-01 TAS 100-1995
PRI Construction Material Technologies(TST5878) AKZC-001-02-01/05 TAS 110-2000
PRI Construction Material Technologies(TST5878)AKZC-001-02-01/05 ASTM B 117-2002
AKZO Nobel Coatings, Inc. Lab Form ASTM G 153
Code Compliance: The product described herein demonstrated compliance with The Florida Building Code (FBC) 2014 Section
1504.3.2. The product evaluation is limited to compliance with the structural wind load requirements of the FBC 2014, as relates
to Rule 61G20-3.
Minimum Slope Range 2/12 Minimum Slope per Florida Building Code 2014, and in accordance with Manufacturers
recommendations.
Installation: Install per manufacturer's recommended details in compliance with FBC 2014 and RAS 133.
Underlayment: Per Manufacturer's installation guidelines per Florida Building Code 2014
Page 2 of 4
anear uiapnragm: values are outswe the scope or tnis report.
Design Procedure: Based on the dimensions of the structure, applicable wind loads are determined using Chapter 16 of the
Florida Building Code 2014 for roof cladding wind loads. These component wind loads for roof cladding are compared to the
allowable pressure listed above. The design professional shall select the applicable erection details to reference in drawings for
correct fastener attachment to his structure and analyze the panel fasteners for pullout and pullover. Support framing must be
compliant with Florida Building Code 2014 Chapter 22 for steel, Chapter 23 for wood and Chapter 16 for structural loading.
Required wind loads shall be determined per project per FBC 2014 and any rational analysis computation shall be prepared by a
licensed design professional.
Certificate of Independence: James Biagi, P.E. does not have nor will acquire financial interest in any company manufacturing or
distributing products under this evaluation. James Biagi, P.E. is not owned or operated or controlled by any company
manufacturing or distributing product under this report.
PRODUCT EVALUATION REPORT
Page 3 of 4
INSTALL DETAILS
Fastener: # 10 HexHead w/neoprene washer per Evaluation Report Specification
TYPICAL ASSEMBLY PROFILE VIEW
wenap
Page 4 of 4
10-9 IWO(1 11 0J o cy l l
i
WWI MU NoA