HomeMy WebLinkAboutNOA - ROOF SYSTEM OVER WOOD DECKMIAMI, SCANNEO
MIAMI-DADE COUNTY
Quaun_ PRODUCT CONTROL SECTION
DEPARTMENT OF REGULATORY AND ECONOMIC.(Q7JtZ +S +� 11805 SW 26 Street, Room 208
BOARD AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOTICE OF ACCEPTANCE NOA RECE VI �p--`" v.miamidade. ov/econom
Polyglass USA, Inc.
150 Lyon Drive JUN I;UO18
Fernley, NV 89408
LST.Lucie County, Permitting
SCOPE:
This NOA is being issued under the applicable rul s and regulations governing the use of construction materials. The
documentation submitted has been reviewed and acepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade'County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas lother than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense cif such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material withi� their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of toe Florida Building Code.
DESCRIPTION: Polyglass Self -Adhered Roof System over Wood Decks
LABELING: Each unit shall bear a permanent llabel with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered a ter a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and! removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety. I
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews NOA# 13-1217.01 and consists of pages 1 through 34.
The submitted documentation was reviewed by Alex Tigera.
NOA No.: 17-1004.09
MIAMI•DADECOUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 1 of 34
i
ROOFING ASSEMBLY APPROVAL
Category: Roofing
Sub -Category: Modified Bitumen
Materials SBS/APP/TPO
Deck Type: Wood
Maximum Design Pressure -112.5 psf
TRADE NAMES OF PRODUCTS MANUF
Product Dimensions
Elastobase 65' 2". x 3' 3-3/8"
XtraFlex SBS Glass 65' 8" x 3' 3-3/8"
Base
Polyglass G2 Base 108' x 36"
Polyanchor 250' x 48"
Elastobase P 65' 8" x 3' 3-3/8"
Elastoflex SA V FR 66' 8" x 3' 3-3/8"
(1.5-mm)
Elastoflex SA V 66' 8" x 3' 3=3/8"
PLUS FR
Elastoflex SA V (1.5- - 66' 8" x 3' 33/8"
mm)
Elastoflex SA V
PLUS
XtraFlex SBS Base
SA
66' 8" x 3' 3 3/8"
66' 8" x 3' 33/8
Elastoflex SA P FR 32' 10" x 3' 3-3/8"
XtraFlex SBS G SA 32' 10" x 3' 3-3/8"
MIAMI•DADE COUNTY
TRED OR LABELED BY APPLICANT:
TABLE 1
Test Product
;ification Description
AS M D 6163,
SBS modified asphalt coated fiberglass reinforced
Type I
base sheet.
AS M D 6163,
SBS modified asphalt coated fiberglass reinforced
Type I
base sheet.
ASTM D 4601
Asphalt -coated fiberglass reinforced base sheet
j Type II
i
ASTM D-4601
A polymer woven, high performance, synthetic base
Type II
sheet.
ASTM D 6164,
SBS modified asphalt coated polyester reinforced base
Type I
sheet.
ASTM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
STM D 6163,
Self -adhered, fire -rated, fiberglass reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a smooth top surface.
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back: face and
a smooth top surface.
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
Type I
bitumen membrane with a self -adhering back face and
a smooth top surface.
ASTM D 6163,
Self -adhered, fiberglass reinforced, SBS modified
Type.l
bitumen membrane with a self -adhering back face and
a smooth top surface.
ASTM D 6164,
Self -adhered, fire -rated, polyester reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
ASTM D 61643
Self -adhered, fire -rated, polyester reinforced, SBS
Type I
modified bitumen membrane with a self -adhering back
face and a granule top surface.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 2 of 34
a
Elastoflex SA P
Polyflex
XtraFlex APP S
Polybond
Polyflex G
Polyflex SA P
Polyflex SA P FR
XtraFlex APP G SA
32' 10" x 3' 3-3/8" ASTr D 6164,
Self -adhered, fiberglass reinforced, SBS modified
ype I
bitumen membrane with a self -adhering back face and
a granule top surface.
32' 10" x 3' 3-3/8" AS D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
32' 10" x 3' 3-3/8" ASTM D 6222
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
32' 10" x 3' 3-3/8" ASTM D 6222
Torch applied, polyester reinforced, APP modified
I
bitumen membrane with a burn off polyethylene back
face and a smooth or sanded top surface.
32' 10" x 3' 3-3/8" ASTM D 6222
32' 10" x 3' 33/8" ASTM D 6222,
Type I
32' 10" x 3' 33/8"
32' 10" x 3' 33/8"
ASi M D 6222,
i Type.I
M D 6222,
Type I
Polyfresko G SBS SA 32' 10" x 3' 33/8" ASTM D 6164,
Type I
Polyfresko G SBS SA 32' 10" x 3' 33/8" ASTM D 6164,
FR I Type I
Polyfresko G APP SA 32' 10" x 3' 33/8" ISTM D 6222,
Type I
Polyfresko G APP SA 32' 10" x 3' 33/8" ASTM D 6222,
FR I Type I
i
PolyKo61 32' 10" x 3' 33/8" ASTM D6222
Type I
XtraFlex Kool APP S 32' 10" x 3' 33/8" ASTM D6222
SA Type I
Polyglass APP Base 65' 8" x 3' 33/8" ASTM D 6509
Type I
MIAMI•DADE COUNTY
Torch applied, polyester reinforced, APP modified
bitumen membrane with a burn off polyethylene back
face and a granule top surface.
Self -adhered, polyester reinforced, APP modified
bitumen membrane with a self -adhering back face and
a granule top surface.
Self -adhered, fire -rated, polyester reinforced, APP
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Self -adhered, fire -rated, polyester reinforced, APP
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Self -adhered, fiberglass reinforced, SBS modified
bitumen membrane with a self -adhering back face and
a granule top surface.
Self -adhered, fire -rated, fiberglass reinforced, SBS
modified bitumen membrane with a self -adhering back
face and a granule top surface.
Self -adhered, polyester reinforced, APP modified
bitumen membrane with a self -adhering back face and
a granule top surface.
Self -adhered, fire -rated, polyester reinforced, APP
modified bitumen membrane with a self -adhering back
face and a granule top surface
Self -adhered, polyester reinforced, APP modified
bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
Self -adhered, polyester reinforced, APP modified
bitumen membrane with a self -adhering back face and
a white film laminate on the top surface.
APP modified asphalt coated fiberglass reinforced
base sheet.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 3 of 34
PG325 Cold Process
Adhesive
PG100 Asphalt Primer
XtraFlex 10 Asphalt
Primer
PG350 Mod Bit
Adhesive
PG400 Plastic Roof
Cement
PG425 Wet/Dry Roof
Cement
PG450 Flashing
Cement
PG500 MB Flashing
Cement
Polyplus 35 Premium
Mod Bit Adhesive
XtraFlex 35 Premium
Mod Bit Adhesive.
Polyplus 45 Premium
Flashing Cement
Polyplus 50 Premium
MB Flashing Cement
XtraFlex 50 Premium
Modified Wet/Dry
Cement
Polyplus 55 Premium
Modified Flashing
Cement
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal,
tube or 17 oz. spray
can
1, 3, 5, 50, 55 gal,
tube or 17 oz. spray
can
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal: or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
1, 3, 5, 50, 55 gal. or
tube
i
i
ASTM D3019 A fibered cold process adhesive for use with roll or
Type III BUR roofing.
ASTM D41 A penetrating solution of solvent and a blend of
selected asphalts used to promote adhesion.
TM D41 A penetrating solution of solvent and a blend of
selected asphalts used to promote adhesion.
�M D3019
A fibered rubberized adhesive designed for use with
(Type III
modified bitumen membranes.
TM D4586
A thick, fibered, rubberized flashing cement for use in
TM D3409
dry or damp conditions.
TM D4586
A thick, fibered, rubberized flashing cement for use in
TM D3409
dry or damp conditions.
TM D4586
A thick, fibered, rubberized flashing cement.
TM D4586
A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
TM D3019
A fibered rubberized adhesive designed for use with
Type III
modified bitumen membranes.
TM D3019
A fibered rubberized adhesive designed for use with
Type III ,
modified bitumen membranes.
TM D4586
A thick, fibered, rubberized flashing cement.
D4586 A thick, fibered, rubberized flashing cement for use
with modified bitumen membranes.
D4586 A thick, .fibered, rubberized flashing cement for use
with modified bitumen membranes.
D4586 A mastic compound for use as a roof flashing
adhesive.
NOA No.: 17-1004.09
MiAMIOADe cI' IV mill q ouNnr Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 4 of 34
a
APPROVED INSULATIONS:
Product Name
Polytherm-H
Polyisoc
Polytherm
Polyisoc
ACFoam-II
Polyisoc
ACFoam-III
Polyisoc
High Density Wood Fiberboard
Wood fi
DensDeck, DensDeck Prime
Gypsum
H-Shield
Polyisoc
H-Shield CG
Polyisoc
ENRGY-3
Polyisoc
Fesco Board
Expande
Multi -Max FA-3
Polyisoc
SECUROCK Gypsum -Fiber Roof Board
Fiber rei
MIAMI•DADE COUNTY
i
l
TABLE 2
Product Description
inurate foam insulation
murate foam insulation
murate foam insulation
murate foam insulation
:r insulation board
isulation board
murate foam insulation
murate/perlite composite insulation
murate foam insulation
mineral fiber
murate foam insulation
.orced coverboard
Manufacturer
ith Current NOA
Polyglass USA, Inc.
Polyglass USA, Inc.
Atlas Roofing Corp
Atlas Roofing Corp
Generic
Georgia-Pacific Gypsum LLC
Hunter Panels, LLC
Hunter Panels, LLC
Johns Manville Corp.
Johns Manville Corp.
Rmax Operating, LLC.
'United States Gypsum
Corporation
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 5 of 34
t
APPROVED FASTENERS:
i TABLE 3
Fastener
Product
Product
Number
Name
I Description
1.
Dekfast Fasteners 12, 14 &
Insulatio fastener for wood,
15 HS
steel and concrete decks
2.
Dekfast Galvalume Steel
Galvalu e hex stress plate.
Hex Plate
3.
#14 Roofgrip
Insulation and membrane
fastener
4.
Flat Bottom Metal Plate
A2-SS a uminized steel plate
5.
Trufast #14 HD Fastener
Insulation fastener for steel and
wood delcks
6.
Trufast 3" Metal Insulation
Round Galvalume AZ50 steel
Plate
plate
7.
Polygrip Fasteners 412, #14
Insulation fastener for wood,
& #15
steel and concrete decks
8.
Polygrip Hex Plates
Galvalulme hex stress plate.
MIAMI•DADE COUNTY
Manufacturer
Dimensions
(With Current NOA)
SFS Intec, Inc.
2 7/8" x
SFS Intec, Inc.
3 '/a"
Various
OMG, Inc.
3" square
OMG, Inc.
Altenloh, Brinck & Co.
U.S., Inc.
3.23 round
Altenloh, Brinck & Co.
3" round
U.S., Inc.
Various
Polyglass USA, Inc
2 7/8" x
Polyglass USA, Inc
3 1/4"
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 6 of 34
APPROVED SURFACING:
Product Prt
Name Desci
PG200 Non-Fibered Roof Coating A non fibered asp
to add life and rej
BUR roofing subs
XtraFlex 20 Bituminous Roof A non fibered as
Coating to add life and r ji
BUR roofing subs
TABLE 4
coating used
to existing
Application
Rate
1'/2-2 gal/sq
coating used 1'h-2 gal/sq
to existing
PG300 Fibered Roof Coating An asphalt cutback fibered roof
coating. May b� applied by brush or
spray equipmeto rejuvenate aged
BUR
XtraFlex Bituminous Roof An asphalt cutback fibered roof
Coating Fibered coating. May be applied by brush or
spray equipment to rejuvenate aged
BUR
PG600 Non-Fibered Aluminum
Non-fibered a]
Roof Coating
PG650 Fibered Aluminum Roof
Fibered alumii
Coating
PG700 Elastomeric Roof Coating
A premium wl
based roof coE
polyester fabri
reinforcement
PG800 Non-Fibered Asphalt
An asphalt ba:
Emulsion Roof Coating
emulsion
XtraFlex 80 Emulsion Roof
An asphalt bay
Coating
emulsion
PG850 Fibered Asphalt Emulsion
An asphalt M
Roof Coating
emulsion
Polyplus 65 Premium Fibered
Fibered alumi
Aluminum Roof Coating
Specification
TAS 140
TAS 140
Manufactur
er
Polyglass
USA, Inc.
Polyglass
USA, Inc.
1'/2-2 gal/sq ASTM D4479 Polyglass
USA, Inc.
1'/2-2 gal/sq ASTM D4479 Polyglass
USA, Inc.
roof coating. 1/2-1 gal/sq
roof coating. 1'h-2 gal/sq
.e elastomeric acrylic 1-1'/2 gal/sq
ng (water -based). A
may be used for
,ith this coating.
, un-fibered clay 3 gal/sq in
un-fibered clay
fibered clay
roof coating.
XtraFlex 65 Aluminum Roof Fibered aluminum roof coating.
Coating Fibered
Polyplus 60 Premium Non- Non-fibered 'aluminum roof coating.
Fibered Aluminum Roof Coating
XtraFlex 60 Aluminum Roof Non-fibered aluminum roof coating.
Coating
MIAMI-DADE COUNTY
,,
two coats
3 gal/sq in
two coats
3 gal/sq in
two coats
1'/2-2 gal/sq
1'/2-2 gal/sq
1/2-1 gal/sq
1/2-1 gal/sq
ASTM D2824
Polyglass
Type I
USA, Inc.
ASTM D2824
Polyglass
Type III
USA, Inc.
ASTM D6083
Polyglass
USA, Inc.
ASTM D 1227
ASTM D1227
ASTM D1227
ASTM D2824
Type III
ASTM D2824
Type III
ASTM D2824
Type I
ASTM D2824
Type I
Polyglass
USA, Inc.
Polyglass
USA, Inc.
Polyglass
USA, Inc.
Polyglass
USA, Inc.
Polyglass
USA, Inc.
Polyglass
USA, Inc.
Polyglass
USA, Inc.
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 7 of 34
1
APPROVED SURFACING:
TABLE 4
Product
Product
Application
Name
Description
Rate
Polybrite 70 Premium Grade
A premium white elastomeric acrylic
1-1'/z gal/sq
Elastomeric Roof Coating
based roof coating (water -based). A
polyester fabric nay be used for
reinforcement with this coating.
XtraFlex 70 Premium Acrylic FR
A premium whitI elastomeric acrylic
1-1'/Z gal/sq
Roof Coating
based roof coating (water -based). A
polyester fabric pay be used for
reinforcement Aith this coating.
Polybrite 90 High Solids Silicone
A premium graoe high solids, single
fluid
1.25 gal/sq
Roof Coating
component, moisture cure,
applied silicone) coating
XtraFlex SRC 9600 High Solids
A premium grade high solids, single
1.25 gal/sq
Silicone Roof Coating
component, moisture cure, fluid
applied silicone coating
Polybrite 95 Silicone Roof
A single component, solvent,
1.25 gal/sq
Coating
moisture cure sPicone coating.
XtraFlex SRC 8000 Silicone Roof
A single component, solvent,
1.25 gal/sq
Coating
moisture.cure silicone coating.
Gravel
To be installed in a flood coat of
4001bs/sq
approved asphlalt at 60 lbs/sq
Slag
To be installed in a flood coat of
300 lbs/sq
approved asp4alt at 60 lbs/sq
Specification Manufactur
er
ASTM D6083 Polyglass
USA, Inc.
ASTM D6083 Polyglass
USA, Inc.
ASTM D6694 Polyglass
USA, Inc.
ASTM D6694 Polyglass
USA, Inc.
ASTM D6694 Polyglass
USA, Inc.
ASTM D6694 Polyglass
USA, Inc.
N/A Generic
N/A Generic
NOA No.: 17-1004.09
MIAMI•DADECOUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 8 of 34
i
I
EVIDENCE SUBMITTED:
Test Asency
Factory Mutual Research
Corporation
Trinity I ERD
PRI Construction Materials
Technologies
QMIAMMI-D�ADE COUNTY
,...• •
44
44
44
TAS 114
TAS 114
TAS 114
TAS 117(B)i ASTM D903
TAS 114
TAS 114
i
TAS 114
TAS 117(B)L ASTM D6862
ASTM D6164 / ASTM D6222
ASTM D616 / ASTM D6222
ASTM D6222
TAS 114(D) ASTM D1876
ASTM D6222
FM 4470 & TAS 114
ASTM D6163 / ASTM D 4601
TAS 114 & TAS. 117 (B)
TAS 114 & TAS 117 (B)
ASTM D6164
ASTM D6164
AS D6163
D6163
ASTM D6222
ASTM D4601 / TAS 117
TAS 114 & FM 4474
TAS 114 (H)
ASTM D4601 / TAS 117
ASTM D6222
ASTM D6222
ASTM D6163
ASTM D6694
ASTM D6694
Report No.
2W7A7.AM
2D5A9.AM
3001334
3000857
3004091
3012321
3014751
3019317
3014692
11752.09.99-1
02764.09.05
02762.03.05
020841.06.04
P 1734.07.06-R 1
P1738.02.07
P1739.01.07
C8500SC.11.07
P 10490.08.08
P10490..10.08-R1
P7400.03.08-R2
P10070.10.08
P 10490.10.08-2
P33970.03.11
P33960.03.11
11757.12.00-1-R1
11757.04.01-1-R1
P37590.07.13-1
P37590.03.13-3A
P37590.03.13-2-R1
P37590.09.13
P45940.09.13
P41630.08.13
P 13760.09.09
P45970.05.14
PUSA-061-02-02
PUSA-062-02-02
PUSA-064-02-02
PUSA-134-02-01
PUSA-135-02-01
Date
08.04.94
06.22.99
02.15.00
01.12.00
01.12.00
07.29.07
08.27.03
06.30.04
08.05.03
02.08.00
09.09.05
03.30.05
06.02.04
02.27.07
02.05.07
01.23.07
11.30.07
08.13.08
10.03.08
10.09.08
10.09.08
10.30.08
03.15.11
03.15.11
04.29.13
04.30.13
07.02.13
03.06.13
02.05.13
09.12.13
09.04.13
08.06.13
09.10.09
05.12.14
01.28.08
12.04.08
02.27.08
05.16.14
05.16.14
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 9 of 34
APPROVED ASSEMBLIES:
Membrane Type: SBS/APP
Deck Type II: Wood, Insulated
Deck Description: 19/32" or greater plywood or
System Type A(1): All insulation layers are ad.
subsequently adhered to in
All General and System Limitations apply.
l plank, fastened at 24" spans with #8 wood screws at 6" o.c..
to a mechanically attached anchor sheet. Membrane is
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Polyglass G2 Base, Polyflex*, XtraFlex APP
S*, Polybond* or GAFGLS #75 fastened to the deck as described below:
*with OMG fasteners and Plat Bottom Metal Plates.
Fastening #1: Attach base sheet using 111 ga. annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c.
in a 4" lap and 8" o.c. in tkiree equally spaced staggered rows in the center of the sheet.
Fastening #2: Attach base sheet using O1M_G #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
14 with Galvalume Steel Hex Plates or Polygrip Fasteners #14 with Polygrip Hex Plates or
Trufast #14 HD Fastenersi with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap
and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft2
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick N/A N/A
Note: All insulation shall be adhered to the �nchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 it'. Please refer to- Roofing Application Standard RAS 117- for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with.a second layer
of approved top layer insulation installed as t�e final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyal urate side facing down.
Top Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum 1/4" thick j N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping. asphalt within the EVT range
and at a rate of 20-40 lbs/100 W. Please refer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
i
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V Fi2 (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
i
NOA No.: 17-1004.09
Mu►r+anaoeeouNrr i Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 10 of 34
r'-- --
Membrane: One ply of Polyfresko G SBiS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
Surfacing: (Optional) Install one of th� approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See general li
MIAMI•DADE COUNTY
_F11221(shill
#7.)
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 11 of 34
i
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or Lod plank, fastened at 24" spans with 48 wood screws at 6" o.c.
System Type A(2): All insulation layers are adhered to a mechanically attached anchor sheet. Membrane is
subsequently adhered to insulation.
All General and System Limitations apply. Roo accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utili ing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P, Polyglass G2 Base, Polyflex,
XtraFlex APP S or Polvbond fastened to the deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
O.C. in a 4" lap and 12" o.q. in two equally spaced staggered rows in the center of the sheet.
One or more of the following
Base Insulation Laver (Optional)
Any approved Polyisocyanurate listed in Ta
Minimum 1" thick
Top Insulation Laver
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum 1/4" thick l
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Note: All insulation shall be adhered to the anchor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 f�t2. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as ba a layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as t1I a final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS GSA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or I
One ply of Polyflex G, torch -applied.
MIAMI•DADE COUNTY
,..., M,
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 12 of 34
Surfacing:
Maximum Design
Pressure:
MIAMI•DADE COUNTY
F1129ROYRIJ
(Optional) Install one of the
coating or required fire clas
-60 psf; (See general
#7.)
surfacing products listed in Table 4 to obtain desired
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 13 of 34
I
I
i
I
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
I
Deck Description: 19/32" or greater plywood or'
or #8 wood screws at 6" o.c.
System Type A(3): All insulation layers are ad1I
subsequently adhered to cost
plank, fastened at 24" spans with 8d common nails at 4" o.c.
to a mechanically attached anchor sheet. Membrane is
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories Idemonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Polyglass G2 Base fastened to the deck as described below:
Fastening:
Attach base sheet using 11Iga. Annular ring shank and 1-5/8" diameter tin caps spaced 8" o.c.
in a 4" lap and 8" o.c. in tl}ree equally spaced staggered rows in the center of the sheet.
One of more of the following:
Base Insulation Laver (Optional)
Any approved Polyisocyanurate listed in Table
Minimum 1" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
Note: All insulation shall be adhered to the an chor sheet in full mopping of approved hot asphalt within the
EVT range and at a rate of 20-40 lbs/100 ff. Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as bane layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as tide final.membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Top Insulation Laver
Dens Deck, Dens Deck Prime, SECUROCK
Minimum'/a" thick
Insulation Fasteners Fastener
Table 3 Density/ft2
Roof Board
N/A N/A
Note: Apply top layer of insulation in a full mopping of any approved mopping asphalt within the EVT range
and at a rate of. 20-40 lbs/100 ft2. Please Irefer to Roofing Application Standard RAS 117 for insulation
attachment. Insulation listed as Base Layer only shall be used only as base layers with a second layer of
approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet:
MIAMI•DADE COUNTY
One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
i
NOA No.: 17-1004.09
Expiration Date: 10/11/22
I
Approval Date: 10/12/17
Page 14 of 34
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, �lastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torc -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See general limitation #7.)
NOA No.: 17-1004.09
MIAMI•DAD; COUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 15 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or
System Type A(4): All insulation layers are adl�
subsequently adhered to in gi
i plank fastened at 24" spans with #8 wood screws at 6" o.c.
to a mechanically attached anchor sheet. Membrane is
on.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Anchor Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened as below:
Fastening: 12 ga. Annular ring shank hails and 1-5/8" tin -caps attached 6" o.c. in 4" lap and 6" o.c. in four
equally spaced staggered rows.
Base Insulation Laver Insulation Fasteners Fastener
Table 3 Density/ft2
ACFoam-II, Polytherm, ACFoam-III, H-Shieldp Polytherm-H, H-Shield CG, Multi -Max FA-3, ENRGY 3
Minimum 1" thick j N/A N/A
Note: All insulation shall be adhered to the anchor sheet with Millennium One -Step Foamable Adhesive applied
over rows of tin -caps in continuous rows 7" o.cj Please refer to Roofing Application Standard RAS 117 for
insulation attachment. Insulation listed as base layer only shall be used only as base layers with a second layer
of approved top layer insulation installed as the final membrane substrate. Composite insulation panels may be
used as a top layer placed with the polyisocyanurate side facing down.
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm); Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G
Polyfresko, G APP SA F
SA P, PolyKool, XtraFlc
adhered.
Or
One ply of Polyflex G, b
3S SA, Polyfresko G SBS-SA FR, Polyfresko G APP SA,
Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
Surfacing: (Optional) Install one ofithe approved surfacing products listed in Table 4 to obtain desired_
coating or required fire classification.
I
Maximum Design
Pressure: -60 psf, (See general limitation V.)
NOA No.: 17-1004.09
MLAMI-Daoe COUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 16 of 34
Membrane Type:
Deck Type 1I:
Deck Description:
System Type C(1):
SBS/APP
Wood, Insulated
19/32" or greater plywood or
screws at 4" o.c.
All layers of insulation are
adhered to insulation.
All General and System Limitations apply. Roo
and shall not be installed unless said accessories
Code requirements and are field fabricated utili
One or more of the following
Base Insulation Laver
Any approved Polyisocyanurate listed in Table
Minimum 1.511 thick
Note: All layers shall be simultaneously
panels listed are minimum sizes and din
increased maintaining the same fastener
insulation attachment.
Ton Insulation Laver
Approved High Density Wood Fiberboard
Minimum 1/211 thick
DensDeck
Minimum 1/4" thick
Note: All layers of insulation shall be in
insulation panels listed are minimum sizes
shall be increased maintaining the same f.
117 for insulation attachment.
plank, fastened at 24" spans with 8d common nails or wood
attached to roof deck. Membranes subsequently
• accessories not listed in Table 1 of this NOA are not approved
demonstrate compliance with prescriptive Florida Building
sing the approved membranes listed in Table 1.
Insulation Fasteners Fastener
Table 3 Density/ft'
N/A NIA
1; see top layer below for fasteners and density. Insulation
if larger panels are used, the number of fasteners shall be
Please refer to Roofing Application Standard RAS 117 for
Insulation Fasteners Fastener
Table 3 Density/ft'
1 1:1.33 W
1 1:1.33 ft2
iically attached using the fastener density listed above. The
dimensions; if larger panels are used, the number of fasteners
;r density. Please refer to Roofing Application Standard RAS
Base Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FRI(1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko GiSBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G'SA, Polyflex
SA P, PolyKool, XtraFl x Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
i
One ply of Polyflex G, ti orch-applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
NOA No.: 17-1004.09
�MIAMOADEouN nr Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 17 of 34
f
coating or required fire classification.
Maximum Design
Pressure: -67.5 psf; (See General limitation #7.)
NOA No.: 17-1004.09
MIAMI-DADECOUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 18 of 34
s
i
Membrane Type: SBS/APP j
Deck Type 1I: Wood, Insulated j
Deck Description: 19/32" or greater plywood or wood plank, fastened at 24" spans with 8d common nails at 4" o.c.
System Type C(2): All layers of insulation are mechanically attached to roof deck. Membranes subsequently
adhered to insulation.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table
Minimum 1.5" thick
Note: All layers shall be simultaneously
panels listed are minimum sizes and din
increased maintaining the same fastener
insulation attachment.
Top Insulation Laver
Approved High Density Wood Fiberboard
Minimum 1/2" thick
DensDeck
Minimum 1/a" thick
Note: All layers of insulation shall be m
insulation panels listed are minimum sizes
shall be increased maintaining the same f:
117 for insulation attachment.
Base Sheet: One or more plies of
SA, Elastoflex SA V
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
d; see top layer below for fasteners and density. Insulation
if larger panels are used, the number of fasteners shall be
Please refer to Roofing Application Standard RAS 117 for
Insulation Fasteners Fastener
Table 3 Density/ft2
1 1:1.33 ftz
1 1:1.33 ft2
mically attached using the fastener density listed above. The
dimensions; if larger panels are used, the number of fasteners
.er density. Please refer to Roofing Application Standard RAS
oflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G iSBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFldx Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
i
NOA No.: 17-1004.09
MIAMI•DADECOUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 19 of 34
Surfacing:
Maximum Design
Pressure:
(Optional) Install one of thelapproved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
-67.5 psf; (See General
#7.)
NOA No.: 17-1004.09
MIAMI-DADECOUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 20 of 34
y
Membrane Type:
Deck Type 1I:
Deck Description:
System Type C, (, i
SBS/APP
Wood, Insulated
"/32" or greater plywood or
All layers of insulation are
adhered to insulation.
plank, fastened at 24" spans with wood screws at 6" o.c.
nically attached to roof deck. Membranes subsequently
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more of the following:
Insulation Laver Insulation Fasteners Fastener
Table 3), Density/ft2
ENRGY 3,' olytherm-H, ACFoam-II Polytherm
Minimum 1.5" thick 1, 5 or 7 1:1.33 ftz
Note: All layers of insulation shall be mechanically attached using the fastener density listed above. The
insulation panels listed are minimum sizes and dimensions; if larger panels are used, the number of fasteners
shall be increased maintaining the same fastener density. Please refer to Roofing Application Standard RAS
117 for insulation attachment. 1
Base Sheet:
Membrane:
Surfacing:
Maximum Design
Pressure:
MIAMI•DADE COUNTY
One or more plies dfi�Elastoflex-SA�UI(1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
One ply of Polyfresko G
Polyfresko G APP SA F:
SA P, PolyKool, XtraFle
adhered.
Or
One ply of Polyflex G, b
(Optional) Install one of
coating or required fire i
i
-82.5 psf; (See General 1
i
S SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
,,Tast0flexS9 ' Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
-I A-un_c — e_pntuflax_SA P FR or XtraFlex APP G SA, self-
Membrane Type:
Deck Type 1I:
Deck Description:
System Type D(1):
SBS/APP
Wood, Insulated
"/32" or greater plywood or
plank, fastened at 24" spans with #8 wood screws at 6" o.c.
All insulation is loosed laid with preliminary attachment to deck. Base sheet is subsequently
mechanically fastened thro gh insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply. Roo accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Laver I Insulation Fasteners Fastener
Table 3 Density/ft'
Any approved Polyisocyanurate listed in Table 2
Minimum 1" thick N/A N/A
Ton Insulation Laver (Optional) Insulation Fasteners Fastener
Table 3 Density/ft2
Fesco Board
Minimum V thick N/A N/A
Approved High Density Wood Fiberboard
Minimum %11 thick N/A N/A
DensDeck, DensDeck Prime, SECUROCK Gypsum -Fiber Roof Board
Minimum'/a" thick N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation boards having no dimension greater than 8 ft.
Base Sheet: One or more plies of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor
fastened to the deck as described below:
Fastening: Attach base sheet using I MG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
14 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners 414 with Polygrip Hex Plates
or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a 4" lap
and 12" o.c. in two equailly spaced staggered rows in the center of the sheet.
Ply Sheet: One dr more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
I
I
I
I
NOA No.: 17-1004.09
MIAMI•DADECOUNTY ;. Expiration Date: 10/11/22
1
Approval Date: 10/12/17
Page 22 of 34
Membrane:
Surfacing:
Maximum Design
Pressure:
i
One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch -applied.
(Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
-52.5 psf; (See General
#7.)
NOA No.: 17-1004.09
M AMI•DADE COUNTY
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 23 of 34
Membrane Type: SBS/APP
Deck Type 1I: Wood, Insulated
Deck Description: 19/32" or greater plywood or ood plank, fastened at 24" spans with #8 wood screws at 6" o.c.
System Type D(2): All insulation is loosed laidith preliminary attachment to deck. Base sheet is subsequently
mechanically fastened throZ insulation to the roof deck. Membranes subsequently adhered.
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated util►zing the approved membranes listed in Table 1.
One or more layers of the following:
Base Insulation Laver
Any approved Polyisocyanurate listed in Table
Minimum 1" thick
Ton Insulation Laver (Optional)
Fesco Board
Minimum %" thick
Approved High Density Wood Fiberboard
Minimum %" thick
DensDeck, DensDeck Prime, SECUROCK
Minimum 1/a" thick
Roof Board
Insulation Fasteners Fastener
Table 3 Density%ft2
N/A N/A
Insulation Fasteners Fastener
Table 3 Density/ft2
N/A N/A
N/A N/A
N/A N/A
Note: All insulation shall have preliminary attachment, prior to the installation of the roofing membrane at a
minimum application rate of two fasteners per�aving
board for insulation boards having no dimension greater than 4
ft., and four fasteners for any insulation board no. dimension greater than 8 ft.
Base Sheet:
Fastening:
Ply Sheet:
One or more plies of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor
fastened to the deck as de�cribed below:
Attach base sheet using O G.#14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o ;c. in two equally spaced staggered rows in the center of the sheet.
One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex. SA V PLUS FR, self -adhered.
I
NOA No.: 17-1004.09
rfwrai•oaoecouNnr Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 24 of 34
J
R
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torc -applied.
Surfacing: (Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -60 psf; (See General limitation V.)
NOA No.: 17-1004.09
MIAMI•DADECID, TY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 25 of 34
Membrane Type:
Deck Type 1:
Deck Description:
System Type E(1):
SBS/APP
Wood, Non -Insulated
19/32" or greater plywood or
or 48 wood screws at 6" o.c
Base sheet is mechanically a
plank, fastened at 24" spans with 8d common nails at 4" o.c.
to roof deck.
All General and System Limitations apply. Roo1emonstrate
accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, Xtr;lex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
o.c. in a 4" lap and 8" o.c. in three equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastc
SA, Elastoflex SA V FR (1
Membrane: One ply of Polyfresko G S
Polyfresko G APP SA FR,
SA P, PolyKool, XtraFlex
adhered.
Or
One ply of Polyflex G, tor.
Surfacing:
Maximum Design
Pressure:
(Optional) Install one o
coating or required fire
-52.5 psf; (See General
i
QMIUARIMADECOUNTY
SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
n) or Elastoflex SA V PLUS FR, self -adhered.
SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
tstoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
DI APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
approved surfacing products listed in Table 4 to obtain desired
NOA'No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 26 of 34
V
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or,
System Type E(2): Base sheet is mechanically a
plank, fastened at 24" spans with 48 wood screws at 6" o.c.
-d to roof deck.
All General and System Limitations apply. Roof laccessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening #: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates, Dekfast
414 with Dekfast Galvalume Steel Hex Plates, Polygrip Fasteners 414 with Polygrip Hex
Plates or Trufast #14 HD Fasteners with Trufast 3" Metal Insulation Plates spaced 12" o.c. in a
4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1 5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA,
Polyfresko G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex
SA P, PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -
adhered.
Or
One ply of Polyflex G, torch applied.
Surfacing:
Maximum Design
Pressure:
MIAMI•DADE COUNTY
(Optional) Install one of the approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
-60 psf; (See General limitation #7.).
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 27 of 34
v
Membrane Type:
Deck Type 1:
Deck Description:
System Type E(3):
SBS/APP
Wood, Non -Insulated
"/32" or greater plywood or v
o.c. at edges and intermediat
Base sheet is mechanically al
insulation.
►od plank, fastened at 24" spans with 8d ring shank nails at 6"
supports.
rched to roof deck. Membranes subsequently adhered to
All General and System Limitations apply. Roo accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Polyglass APP Blase, Elastobase (Poly/Sand) sheet fastened to the deck as described
below:
Fastening: Attach base sheet using 11 ga. annular grooved shank and 1" diameter caps spaced 6" o.c. in a
3" lap and 6" o.c. in four equally spaced staggered center rows.
Membrane: One ply of Elastoflex SA P I Elastoflex SA P FR, XtraFlex SBS G SA, Polyfresko: G SBS SA,
Polyfresko G SBS SA FR, Polyflex SA P, Polyflex SA P FR, XtraFlex APP G SA, Polyfresko
G APP SA, Polyfresko G APP SA FR, PolyKool or XtraFlex Kool. APP S SA self -adhered.
Surfacing:
Maximum Design
Pressure:
MIAMI•DADE COUNTY
(Optional) Install one of
coating or required fire c
-52.5 psf; (See General Limi
approved surfacing products listed in Table 4 to obtain desired
V).
NOA No.: 174004.09
Expiration Date: 10/11/22 .
Approval Date: 10/12/17
Page 28 of 34
Membrane Type:
Deck Type 1:
Deck Description:
SBS/APP
Wood, Non -Insulated
"/32" or greater plywood or
or #8 wood screws at 6" o.c
System Type E(4): Base sheet is mechanically
insulation.
plank, fastened at 24" spans with 8d common nails at 4" o.c.
to roof deck. Membranes subsequently adhered to
All General and System Limitations apply. Roofiaccessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, Xtra>lex SBS Glass Base, Elastobase P or Polyanchor fastened to the
deck as described below:
Fastening: Attach base sheet using OMG #14 Roofgrip fasteners and Flat Bottom Metal Plates spaced 12"
o.c. in a 4" lap and 12" o.c. in two equally spaced staggered rows in the center of the sheet.
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
G APP SA FR, Elastoflex SA P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
PolyKool, XtraFlex Kool APP S SA, Polyflex SA P FR or XtraFlex APP G SA, self -adhered.
Or
One ply of Polyflex G, torch -applied
Surfacing: (Optional) Install one of tJ approved surfacing products listed in Table 4 to obtain desired
coating or required fire classification.
Maximum Design
Pressure: -52.5 psf; (See General Limitation #7)
NOA No.: 17-1004.09
QMI"AMMI-D oEMC=TY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 29 of 34
W
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or
or 48 wood screws at 6" o.c.
System Type E(5): Base sheet is mechanically a
insulation.
All General and System Limitations apply. Roof
and shall not be installed unless said accessories I
Code requirements and are field fabricated utili2
Base Sheet: One ply of Elastobase, X
described below:
Fastening: Attach base sheet using 11 g�
o.c. in a 4" lap and 8" o.c. in
Ply Sheet: One or more plies of Elastc
SA, Elastoflex SA V FR (1
Membrane: One ply of Polyfresko G SB
G APP SA FR, Elastoflex S
PolyKool, XtraFlex Kool A
Or
One ply of Polyflex G, torcl
Surfacing: (Optional) Install one of the
coating or required fire clan
Maximum Design
Pressure: -52.5 psf; (See General
MIAMI•DADE COUNTY
plank, fastened at 24" spans with 8d common nails at 4" o.c.
to roof deck. Membranes subsequently adhered to
essories not listed in Table 1 of this NOA are not approved
lonstrate compliance with prescriptive Florida Building
the approved membranes listed in Table 1.
SBS Glass Base or Elastobase P fastened to the deck as
. annular ring shank nails and 1-5/8" diameter tin caps spaced 8"
hree equally spaced staggered rows in the center of the sheet.
x SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
mm) or Elastoflex SA V PLUS FR, self -adhered.
SA, Polyfresko G SBS SA FR, Polyfresko G APP SA, Polyfresko
P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
' S SA, Polyflex SA P FR or XtraFlex APP G SA, self -adhered.
#7)
surfacing products listed in Table 4 to obtain desired
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 30 of 34
V
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or v
members spaced 48" o.c. wit
System Type E(6): Base sheet is mechanically al
insulation.
od plank, fastened to supports spaced 24" o.c. and to blocking
TruFast TP #IOx2-7/8" screws spaced 6" o.c.
.ched to roof deck. Membranes subsequently adhered to
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraF�lex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: Attach base sheet using 11 ga. annular ring shank nails and 1-5/8" diameter tin caps spaced 4"
o.c. in a 4" lap and 4" o.c. in three equally spaced staggered rows in the center of the sheet.
I
Ply Sheet: One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SBS SA, Polyfresko G SBS SA FR, Elastoflex SA P, Elastoflex SA P
FR or XtraFlex SBS G SA, self -adhered.
Or '[One ply of Polyflex G, torch, applied
Surfacing: (Optional) Install one of the
coating or required fire clas
Maximum Design
Pressure: -97.5 psf; (See General
QMIAMMI.DADE MUNTY
...•
#7)
surfacing products listed in Table 4 to obtain desired
NOA No.: 17-1004.09
Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 31 of 34
L
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 19/32" or greater plywood or
members spaced 48" o.c. A
System Type E(7): Base sheet is mechanically
insulation.
All General and System Limitations apply. Roo
and shall not be installed unless said accessories
Code requirements and are field fabricated utili
Base Sheet:
Fastening:
Ply Sheet:
One ply of Elastobase, X
described below:
Attach base sheet using 12
o.c. in four equally spaced
ood plank, fastened to supports spaced 24" o.c. and to blocking
1 #10x3" wood screws spaced 6" o.c.
:ached to roof deck. Membranes subsequently adhered to
-ssories not listed in Table 1 of this NOA are not approved
onstrate compliance with prescriptive Florida Building
the approved membranes listed in Table 1.
SBS Glass Base or Elastobase P fastened to the deck as
ring shank nails and tin caps spaced 4" o.c. in a 4" lap and 4"
;aered rows in the center of the sheet.
One or more plies of Elastoflex SA V (1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
SA, Elastoflex SA V FR (1.5-mm) or Elastoflex SA V PLUS FR, self -adhered.
Membrane: One ply of Polyfresko G SI
FR or XtraFlex SBS G SA,
Or
One ply of Polyflex G, tore
Surfacing:
Maximum Design
Pressure:
(Optional) Install. one of the
coating or required fire clan
-112.5 psf; With Elastoflex
(See General limitation 47.
-97.5 psf; With Elastoflex <
limitation 47.)
SA, Polyfresko G SBS SA FR, Elastoflex SA P, Elastoflex SA P
surfacing products listed in Table 4 to obtain desired
V PLUS, XtraFlex SBS Base SA or Elastoflex SA V PLUS FR
V(1.5-mm) or Elastoflex SA V FR(1.5-mm) (See General
NOA No.: 17-1004.09
Mu�ru•DADECOUNTY Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 32 of 34
V
Membrane Type: SBS/APP
Deck Type 1: Wood, Non -Insulated
Deck Description: 11/32" or greater plywood or
screws spaced 6" o.c.
System Type E(8): Base sheet is mechanically a
insulation.
plank, fastened to supports spaced 24" o.c. with #8x3" wood
to roof deck. Membranes subsequently adhered to
All General and System Limitations apply. Roof accessories not listed in Table 1 of this NOA are not approved
and shall not be installed unless said accessories demonstrate compliance with prescriptive Florida Building
Code requirements and are field fabricated utilizing the approved membranes listed in Table 1.
Base Sheet: One ply of Elastobase, XtraFlex SBS Glass Base or Elastobase P fastened to the deck as
described below:
Fastening: 12 ga. annular ring shanked
spaced staggered rows. Tin
Asphalt Primer.
Ply Sheet:
Membrane:
Surfacing:
Maximum Design
Pressure:
One or more plies of Elastc
SA, Elastoflex SA V FR (1
One ply of Polyfresko G SB
G APP SA FR, Elastoflex S.
PolyKool, XtraFlex Kool A.
Or
One ply of Polyflex G, torct
(Optional) Install one of the
coating or required fire clas
tils and 1-5/8" tin -caps 6" o.c. in 4" lap and 6" o.c. in four equally
aps are primed. with PG100 Asphalt Primer or XtraFlex 10
x SA V.(1.5-mm), Elastoflex SA V PLUS, XtraFlex SBS Base
mm) or Elastoflex SA V PLUS FR, self -adhered.
SA, Polyfresko G SBS SA FR. Polyfresko G APP SA, Polyfresko
P, Elastoflex SA P FR, XtraFlex SBS G SA, Polyflex SA P,
' S SA, Polyflex SA P FR or XtraFlex APP G SA, self -adhered.
surfacing products listed in Table 4 to obtain desired
-112.5. psf; With Elastoflex Sl� V PLUS, XtraFlex SBS Base SA or Elastoflex SA V PLUS FR
(See General limitation 47.)
-97.5 psf; With Elastoflex SA V(1.5-mm) or Elastoflex SA V FR(1.5-mm) (See General
limitation #7.)
j NOA No.: 17-1004.09
MIAMI•DADE COUNTY j Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 33 of 34
i
WOOD DECK SYSTEM LIMITATIONS:
1. A slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product
Control Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied
within the EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the
top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulatio panel is required on all applications over closed cell foam
insulations when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using
spot mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one
at each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf..
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 lbf., as
tested in compliance with Testing ApplicationStandard TAS 105. If the fastener value,. as field-tested, are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment oi anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener
spacing, prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or
Registered Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal
resistance value taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing
Application Standard RAS 117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers,, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS I I I and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be :permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 17-1004.09
rtwru•DaDe CO Expiration Date: 10/11/22
Approval Date: 10/12/17
Page 34 of 34