HomeMy WebLinkAboutEVALUATION REPORT ROOFING UNDERLAYMENTSSCANNED NEMO I etc.
Certificate of Authorization #32455
353 Christian Street, Unit #13
Oxford, CT 06478
(203) 262-9245
ENGINEER EVALUATE TEST CONSULT CERTIFY
EVALUATION REPORT
Polyglass USA, Inc. Evaluation Report P12060.02.09-R24
1111 West Newport Center Drive FL5259-1128 .
Deerfield Beach, FL 33442 Date of Issuance: 02/24/2009
(954) 233-1230 Revision 24: 01/24/2018
SCOPE:
This Evaluation Report is issued under Rule 63
construction materials in the State of Florida. Th(
for use of the product under the Florida Buildii
described herein have been evaluated for comp
herein.
DESCRIPTION: Polyglass Roof Underlayments
LABELING: Labeling shall be in accordance with tl
CONTINUED COMPLIANCE: This Evaluation Report
Quality Assurance documentation changes, or p
Evaluation Report by the named client consti
product(s), the Quality Assurance or the prod)
Evaluation Report relative to updated Code reqt
i20-3 and the applicable rules and regulations governing the use of
documentation submitted has been reviewed by Robert Nieminen, P.E.
Code and Florida Building Code, Residential Volume. The products
ance with the 61h Edition (2017) Florida Building Code sections noted
requirements the Accredited Quality Assurance Agency noted herein.
valid until such time as the named product(s) changes, the referenced
/isions of the Code that relate to the product change. Acceptance of this
:es agreement to notify Robert Nieminen, P.E. of any changes to the
ion facility location(s). NEIVIO l etc. requires a complete review of this
:ments with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "NEMO I etc. Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection a,t the job site at the request of the Building Official.
This Evaluation Report consists'of pages 1 through 14.
Prepared by:
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
THESE PLANS AND ALL PROPOSED WORK
ARE SUBJECT TO ANY CORRECTIONS
REQUIRED BY FIELD INSPECTORS THAT
MAY BE NECESSARY IN ORDER TO
COMPLY WITH ALL APPLICABLE CODES.
The facsimile seal appearing was authorized by Robert Nieminen,
P.E. on 01/24/2018. This does not serve as an electronically
signed document.
CERTIFICATION OF INDEPENDENCE:
1. NEMOJetc. does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
distributing products it evaluates.
2. NEMO l etc. is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither MEMO I etc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that p se. CONCEALED FASTENERS OR ATTACHMENTS
,,i O C9z ARE THE RESPONSIBILITY OF THE
ST. LUCIE COUNTY BUILDING DIVISION CONTRACTOR OR RECORD
REVIEWED FOR mmoi T .,._
FILE COPY
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: Roof Underlayments,
following sections of the 6th Edition (2017) Flor
Compliance is subject to the Installation Require
2. STANDARDS:
Section
1504.3.1
1504.3.1
1507.2.3 / 1507.1.1
1507.2.4 / 1507.1.1, 1507.2.9.2
1507.3.3
1507.11.2
1507.11.2
TAS 110
3. REFERENCES:
Entity
FM Approvals (TST 1867)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
PRI (TST 5878)
MTI (TST 2508)
MTI (TST 2508)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
ERD (TST 6049)
MEMO ETC, I.I.C.
Certificate of Authorization #32455
OMEMO I etc.
produced by Polyglass USA, Inc., have demonstrated compliance with the
Building Code through testing in accordance with the following Standards.
nts and Limitations / Conditions of Use set forth herein.
plift
plift
I Properties
I Properties
I Properties
I Properties
I Properties
ated Weathering
Standard
FM 4474
UL 1897
ASTM D226
ASTM D1970
FRSA/TRI April 2012
ASTM D6164
ASTM D6222
ASTM D4798
Examination
Reference
Wind Uplift
3004091
Physical Properties
PRIO1111
Physical Properties
PUSA-005-02-01
Physical Properties
PUSA-013-02-01
Physical Properties
PUSA-013-02-02
Physical Properties
PUSA-013-02-03
Physical Properties
PUSA-018-02-01
Physical Properties
PUSA-028-02-01
Physical Properties
PUSA-033-02-01
Physical Properties
PUSA-035-02-01
Physical Properties
PUSA-055-02-02
Physical Properties
PUSA-061-02-02
Physical Properties
PUSA-076-02-01
Physical Properties
PUSA-083-02-01
Physical
Properties
PUSA-088-02-01
Physical
Properties
JX20H7A
Physical
Properties
RX14E8A
Physical
Properties
11752.09.99-1
Wind
Uplift
11757.08.01-1
Wind Uplift
Physical Properties
11776.06.02
02200.07.03
Wind Uplift
P1740.01.07
Physical Properties
P5110.04.07-1
Wind Uplift
P9260.03.08
Physical Properties
P13450.08.09
Wind Uplift
P30540.11.09-R1
Physical Properties
P11030.11.09-1
Wind Uplift
P11030.11.09-2
Physical Properties
P11030.11.09-3
Physical Properties
P33360.06.10
Physical Properties
P33370.03.11
Physical Properties
P33370.04.11
Physi cal Properties
P37300.10.11
6T" EDITION (2017) FBC NON-HVHZ EVALUATION
Polyglass Roof Underlayments; (954) 233-1230
Year
2011
2012
2009
2015
2012
2011
2011
2011
Date
01/12/2000
04/08/2002
01/31/2002
12/23/2002
12/23/2002
12/23/2002
07/14/2003
07/13/2005
01/12/2006
09/29/2006
12/10/2007
01/28/2008
02/22/2008
04/14/2008
07/29/2009
04/01/2008
01/29/2009
02/08/2000
08/13/2001
01/16/2003
07/14/2003
01/04/2007
04/11/2007
03/21/2008
08/13/2009
11/30/2009
11/30/2009
11/30/2009
11/30/2009
06/25/2010
03/02/2011
04/26/2011
10/19/2011
Evaluation Report P12060.02.09-R24
FL5259-R28
Revision 24: 01/24/2018
Page 2 of 14
I
I
I
INNEMOjetc.
Entity Examination Reference Date
ERD (TST 6049) Physical Properties P40390.08.12-1 08/06/2012
ERD (TST 6049) Physical Properties P40390.08.12-2 08/07/2012
ERD (TST 6049) Physical Properties C41420.09.12-3 09/11/2012
ERD (TST 6049) Wind Uplift P39680.03.13 03/04/2013
ERD (TST 6049) Physical Properties P45370.04.13 04/26/2013
ERD (TST 6049) Wind Uplift P1738.02.07-R2 04/29/2013
ERD (TST 6049) Wind 6plift 11757.04.01-1-R1 04/30/2013
ERD (TST 6049) Wind tjplift P41630.08.13 08/06/2013
ERD (TST 6049) Wind Uplift P11751.05.03-R1 11/26/2013
ERD (TST 6049) Wind !I plift P11781.11.03-R1 11/26/2013
ERD (TST 6049) Physical Properties P45270.05.14 05/12/2014
ERD (TST 6049) Physical Properties 6020.07.14-1 09/08/2014
ERD (TST 6049) Physical Properties 6020.09.14-2 09/08/2014
ERD (TST 6049) Physical Properties 6020.09.14-3 09/08/2014
ERD (TST 6049) Physical Properties 6020.09.14-4 09/08/2014
ERD (TST 6049) Physic lal Properties 6020.09.14-5 09/08/2014
ERD (TST 6049) Physic lal Properties 6020.09.14-6 09/08/2014
ERD (TST 6049) Physic lal Properties P46520.10.14 10/03/2014
ERD (TST 6049) Physical Properties P43290.10.14 10/17/2014
ERD (TST 6049) Physical Properties PLYG-SC7550.03.15 03/24/2015
ERD (TST 6049) Physical Properties P40390.04.15 04/03/2015
ERD (TST 6049) Physical Properties P44360.10.14-111 05/18/2015
ERD (TST 6049) Physical Properties PLYG-SC8080.05.15-1 05/20/2015
ERD (TST 6049) Wind1uplift PLYG-SC8905.05.16-1 05/17/2016
ERD (TST 6049) Physical Properties PLYG-SC8080.07.16 07/16/2016
ERD (TST 6049) Wind Uplift PLYG-SC12025.10.16 10/12/2016
ERD (TST 6049) Physical Properties PLYG-SC13040.12.16 12/27/2016
ERD (TST 6049) Physical Properties PLYG-SC11900.03.17 03/10/2017
ERD (TST 6049) Physical Properties PLYG-SC12115.08.17 08/08/2017
ICC-ES (EVL 2396) IBC Compliance ESR-1697 11/01/2014
Miami -Dade (CER 1592) HVHZ Compliance NOA 14-0717.08 01/22/2015
Polyglass USA Manufacturing Affidavit Products Current 02/18/2009
Polyglass USA PA Affidavit Mule -Hide Cross Ltg 03/01/2008
Polyglass USA Materials Affidavit Polystick SA Compound 08/18/2011
UL, LLC. (QUA9625) Quality Control Service Confirmation Exp. 10/05/2018
4. PRODUCT DESCRIPTION:
14.1 Mechanically, Fastened UnderlaymeInts:
4.1.1 Elastobase is a fiberglass reinforced 1 SBS modified bitumen base sheet.
4.1.2 Elastobase P is a polyester -reinforce d, SBS modified bitumen base sheet.
4.1.3 Polyglass G2 Base is a fiberglass -reinforced, asphaltic base sheet.
4.1.4 Polyglass APP Base is a fiberglass -reinforced, APP modified bitumen base sheet
4.1 Self=i 4dherin&Underlayments: ( ��
4.2.1 Polystick MTS or Polystick MTS PLUS is a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass
fiber reinforced, surfaced with polyolefinic film surface; meets FRSA/TRI April 2012.
4.2.2 Polystick IR-Xe is a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with an
aggregate surface; meets ASTM D1970.
I
4.2.3 Polystick TU Plus is a nominal 80-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with a
polyester fabric surface; meets ASTI M D1970 and FRSA/TRI April 2012.
I
NEMO ETC, LLC. Evaluation Report P12060.02.09-R24
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-1128
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 3 of 14
4.2.4
4.2.5
4.2.6
4.2.7
4.2.8
Polystick TU P is a nominal 13,
reinforced, with a granular surface;
OMEMO I etc.
thick rubberized asphalt waterproofing membrane, glass-fiber/polyester
FRSA/TRI April 2012.
Polystick TU Max is a nominal 60-mil rubberized asphalt waterproofing membrane with a 190 g/m2 polyester
fabric surface; meets ASTM D1970 an FRSA/TRI April 2012.
Polyflex SAP, Polyflex SAP FIR, Mule- ide SA-APP Cap Sheet and Mule -Hide SA-APP Cap Sheet (FIR) are polyester
reinforced, APP modified bitumen cap sheets; meet FRSA/TRI April 2012.
Polystick Dual ProTm is a nominal 60-mil thick dual -layer rubberized asphalt waterproofing membrane, fiberglass
reinforced, with a polyester fabric surface; meets ASTM D1970.
Polystick Tile ProTm is a nominal 60rrmil thick dual -layer rubberized asphalt waterproofing membrane, fiberglass
reinforced,,with a polyester fabric surface; meets ASTM D1970 and FRSA/TRI April 2012.
4.2.9 Polystick MU-X is a nominal 54-mi1 thick dual -layer rubberized asphalt waterproofing membrane, fiberglass
reinforced, with a polypropylene film surface; meets AC188 and physical requirements of ASTM D1970 (See Section
5.8).
4.3 Mec hanically'Fastened and/or Bond'e# Underlayments:
4.3.1 Elastoflex G TU is a polyester reinforced, modified bitumen tile underlayment composed of a sand -surfaced SBS
modified bitumen back -side and granule -surfaced APP modified bitumen top -side. Elastoflex G TU is for use as an
alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single Ply System" from FRSA/TRI April
2012 (04-12) beneath mechanically fastened tile roof systems or Hot Asphalt applied "Cap Sheet" in the "Two Ply
System" from FRSA/TRI April 2012 (04112) beneath mechanically fastened or adhered tile roof systems.
4.3.2 Elastoflex S6 G and Elastoflex S6 G FIR are polyester reinforced, SBS modified bitumen cap sheets; meet ASTM D6164.
Elastoflex S6 G and Elastoflex S6 G. FR are for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380,
Class M) in the "Single Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems.
Elastoflex S6 G is for use as an alternate to Hot Asphalt applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI
April 2012 (04-12) beneath mechanically fastened or adhered tile roof systems. Elastoflex S6 G FIR is for use as an
alternate to Hot Asphalt applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath
mechanically fastened tile roof systems
4.3.3 Polyflex G and Polyflex G FIR are polyester reinforced, APP modified bitumen cap sheets; meet ASTM D6222.
Polyflex G is for use as an alternate to Heat Applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012
(04-12) beneath mechanically fastened or adhered tile roof systems. Polyflex G FR is for use as an alternate to Heat
Applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile
roof systems.
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither NEMOIetc. nor Robert Nieminen, P.E. are, in any way, the Designer of
Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or
design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use ii the HVHZ.
5.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire
ratings of this product.
5.4 Polyglass Roof Underlayments may be used with any prepared roof cover where the product is specifically referenced
within FBC approval documents. If; not listed, a request may be made to the Authority Having Jurisdiction for
approval based on this evaluation combined with supporting data for the prepared roof covering.
NEMO ETC, LLC. Evaluation Report P12060.02.09-R24
Certificote ojAuthorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 4 of 14
OMEMO I etc.
5.5 Allowable Roof Covers:
TABLE 1: ROOF CQVER OPTIONS ;
Underla yment
Asphalt Shingles
Nail -On rile
Foam -On Tile
Metal
Wood Shakes
Shingles&
Slate
Elastobase
Yes
(Base S
Yes
eet in 2-ply system)
Yes
(Base Sheet in 2-ply system)
Yes
Yes
Yes
Elastobase P
Yes
(Base 5
Yes
eet In 2-ply system)
Yes
(Base Sheet in 2-ply system)
Yes
Yes
Yes
Polyglass G2 Base
No
(Base S�eet
Yes
in 2-ply system)
Yes
(Base Sheet In 2-ply system)
No
No
No
Polyglass APP Base
No
(Base S
Yes
eet In 2-ply system)
Yes
(Base Sheet in 2-ply system)
No
No
No
Polystick MTS or MTS PLUS
Yes
Yes
No
Yes
Yes
Yes
Polystick IR-Xe
Yes
No
No
No
Yes
Yes
Polystick TU P
No
Yes
Yes (See 5.5.1)
No
No
No
Polystick TU Plus
Yes
Yes
Yes (See 5.5.1)
Yes
Yes
Yes
Polystick TU Max
No
Yes
Yes (See 5.5.1)
Yes
No
No
Polystick Dual Pro
Yes
No
No
Yes
Yes
Yes
Polystick Tile Pro
Yes
Yes
Yes (See 5.5.1)
Yes
Yes
Yes
Polystick MU-X
Yes
No
No
Yes
Yes
Yes
Elastoflex S6 G
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Elastoflex 56 G FR
Yes
Yes
No
No
Yes
Yes
Elastoflex G TU
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Polyflex G
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Polyflex G FR
Yes
Yes
No I
No
Yes
Yes
Polyflex SAP or SAP FR
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Mule -Hide SA-APP Cap Sheet
or SA-APP Cap Sheet (FR)
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
5.5.1 "Foam -On Tile" is limited to use of the following Approved tile adhesives / underlayment combinations.
TABLE
1A:�ALLOWABLE TILE ADHESIVE / UNDERLAYMENT COMBINATIONS)
FloridaI Product
Adhesive
Approval
Underlayments
DAP Foam Touch 'n Seal StormBond Roof
Tile Adhesive .
FL14506
Polystick TU Plus, Polystick TU Max
Dow TileBond'"
FL22525
Polystick TU P, Polystick TU Plus, Polyflex SAP or Tile Pro
Polystick TU P, Polystick TU Plus, Polystick TU Max, Polystick Tile Pro,
ICP Adhesives Polyset® AH-160
FL6332
Elastoflex G TU, Elastoflex S6 G, Polyflex G, Polyflex SAP, Polyflex SA Cap FR,
Mule -Hide SA-APP Cap Sheet or Mule -Hide SA-APP Cap Sheet (FR)
Polystick TU P, Polystick TU Plus, Polystick TU Max, Polystick Tile Pro,
ICP Adhesives Polyset® RTA-1
FL6276
Elastoflex G TU, Elastoflex S6 G, Polyflex G, Polyflex SAP, Polyflex SA Cap FR,
Mule -Hide SA-APP.Cap Sheet or Mule -Hide SA-APP Cap Sheet (FR)
' Refer to Tile Manufacturer's or Adhesive Manufacturer I Florida Product Approval for Overturning Moment Resistance Performance.
MEMO ETC, I.I.C. IEvaluation Report P12060.02.09-R24
Certificate of Authorization #32455 6'" EDI ION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 5 of 14
5.6 Allowable Substrates:
5.6.1 Direct -Bond to Deck:
5.6.2
5.6.3
Polystick (all variations), Dual Pro, Tili
(FR) self -adhered to:
➢ New untreated plywood; ASTM D'
plywood; New or existing, unprii
Southern Yellow Pine; ASTM D4:
(designed and installed to meet wi
ONEMO I etc.
Pro, Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet
L primed new untreated plywood; Existing plywood; ASTM D41 primed existing
ed OSB; ASTM D41 primed OSB; Southern Yellow Pine; ASTM D41 primed
primed structural concrete; Huber Engineered Woods "ZIP System" Panels
d loads for project).
Note: Polyglass does not require priming of new or existing plywood or OSB sheathing. New or existing plywood or
OSB sheathing should be cleaned of all dirt and debris prior to application of Polystick membranes.
Elastoflex G TU, Elastoflex S6 G or Ela$tofle)
➢ ASTM D41 primed structural concrete.
Polyflex G or Polyflex G FR torch -applied to:
➢ ASTM D41 primed structural concrete.
Bond -to -Insulation:
S6 G FR in hot asphalt to:
Polystick (all variations), Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) self -adhered
to:
➢ ASTM C1289, Type II, Class 1 polyisocyan u rate or Type V polyisocyanurate-composite insulation; Dens Deck
DuraGuard; Dens Deck Prime; or SECUROCK Gypsum -Fiber Roof Board.
Elastoflex G TU, Elastoflex S6 G or Ela
➢ Dens Deck Prime or SECUROCK Gy
Polyflex G or Polyflex G FR torch-appl
➢ ASTM D41 primed structural conci
For installation under mechanically
requirements of the prepared roof c
systems, insulation attachment shall
the insulation/underlayment system
Polystick (all variations), Polyflex SA
Tile Pro self -adhered to:
➢ ASTM D226, Type I or II felt; Elast
Elastoflex G TU, Elastoflex 56 G or Eli
➢ ASTM D226, Type I or II felt; Elast
)flex S6 G FR in hot asphalt to:
um -Fiber Roof Board.
to:
; Dens Deck Prime or SECUROCK Gypsum -Fiber Roof Board.
:tached prepared roof coverings, insulation shall be attached per minimum
rering manufacturer's Product Approval. For installations under foam -on tile
designed by a qualified design professional and installed based on testing of
accordance with FBC Section 1504.3.1.
or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) Dual Pro or
Elastobase P or Mule -Hide Nail Base.
(S6 G FR in hot asphalt to:
Elastobase P, Mule -Hide Nail Base or Polyglass G2 Base.
Polyflex G or Polyflex G FR torch -applied to:
➢ Elastobase; Elastobase P, Mule -Hide Nail Base, Polyglass G2 Base or Polyglass APP Base.
For installations under mechanically! attached prepared roof coverings, base layer shall be attached per minimum
codified requirements. For installations under foam -on tile systems, base layer shall be attached per minimum
requirements of FRSA/TRI April 2012,1(04-12), Appendix A, Table 1, or as listed in Section 5.6.4 herein, or as tested in
accordance with FBC Section 1504.3.1.
NEMO ETC, I.I.C.
Certificate of Authorization #32455
6T" EDI IION (2017) FBC NON-HVHZ EVALUATION
Polyglass Roof Underlayments; (954) 233-1230
Evaluation Report P12060.02.09-1124
FL5259-R28
Revision 24: 01/24/2018
Page 6 of 14
i
ON EMO I etc.
5.6.4 Wind Resistance for Underlayment Svstems in Foam -On Tile Applications: FRSA/TRI April 2012 (04-12) does not
address wind uplift resistance of all underlayment systems beneath foam -on tile systems, where the underlayment
forms part of the load -path. The following wind uplift limitations apply to underlayment systems that are not
addressed in FRSA/TRI April 2012 (04112) and are used in foam -on tile applications. Maximum Design Pressure is the
result of testing for wind load resistance based on allowable wind loads, and reflects the ultimate passing pressure
divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has already been applied). Refer to FRSA/TRI April 2012 (04-
12), Appendix A, Table 1A or FBC 1609 for determination of design wind loads.
#1 Maximum Design Pressure = -90 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: None
Base Ply: (Optional) Polystick MTS or Polystick MTS PLUS, self -adhered.
Underlayment: Polystick TU P, Polystick TU Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
Mule -Hide SA-APP Cap Sheet (FR), self -adhered.
#2 Maximum Design Pressure = -97 5 psf
Deck: Min. p 15 32-inch pl
ywood ywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG100orASTM D41
Base Ply: (Optional) Polystick MTS o Polystick MTS PLUS, self -adhered.
Underlayment: Polystick TU P, Polystick TU Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
Mule -Hide SA-APP Cap Sheet (FR), self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x
1Y4" ring shank nails through 32 ga., 1-5/8" diameter tin caps spaced 12-inch o.c.
#3 Maximum Design Pressure = -105 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: WB-3000
Base Ply: (Optional) Polystick MTS or Polystick MTS PLUS, self -adhered.
Underlayment: Polystick TU P, Polystick TU Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
Mule -Hide SA-APP Cap She (FR), self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x
1%" ring shank nails throug32 ga., 1-5/8" diameter tin caps spaced 12-inch o.c.
#4 Maximum Design Pressure = -135 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: (Optional) PG100 or ASTM D41
Base Ply: (Optional) Polystick MTS orlPolystick MTS PLUS, self -adhered.
Joints: Min. 4-inch wide strips of Elastoflex SA-V over all plywood joints.
Underlayment: Polystick TU P, Polystick TUI Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
Mule -Hide SA-APP Cap Sheet (FR), self -adhered.
#5 Maximum Design Pressure = -315 psf:
Deck: Structural concrete to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG100 or ASTM D41
Base Ply: (Optional) Polystick MTS or Polystick MTS PLUS, self -adhered.
Underlayment: Polystick TU P, Polystick TU Plus, Polystick TU Max, Tile Pro, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap
Sheet and Mule -Hide SA-APP Cap Sheet (FR), self -adhered.
#6 Maximum Design Pressure = -622.5 psf!
Deck: Structural concrete to meet project requirements to satisfaction of Authority Having Jurisdiction.
Primer: PG100 or ASTM D41
Underlayment: Elastoflex G TU or Elastoflex'S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#7 Maximum Design Pressure = -30 0 psf* j
Deck: Min. 15/32-inch OSB to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: it ga. x 1.25-inch long x 1-inch head diameter round metal cap nails
Spacing: 6-inch o.c. at the 3-inch wide side laps and 6-inch o.c. at two (2) equally spaced staggered center rows.
Base Ply: (Optional) Polystick MTS or Polystick MTS PLUS, self -adhered.
Underlayment: Polystick TU P, Polystick TU Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
Mule -Hide SA-APP Cap Sheet (FR), self -adhered.
NEIVIO ETC, I.I.C. Evaluation Report P12060.02.09-R24
Certificate of Authorization #32455 6" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 7 of 14
#8
#9
#10
#11
Maximum Design Pressure = -37.5 psfl*:
IRNEMOJetc.
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: 11 ga. x 1.25-inch long x 11inch head diameter round metal cap nails
Spacing: 6-inch o.c. at the 3-inch wjde side laps and 6-inch o.c. at two (2) equally spaced staggered center rows.
Base Ply: (Optional) Polystick MTS oir Polystick MTS PLUS, self -adhered.
Underlayment: Polystick TU P, Polystick TU Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
Mule -Hide SA-APP Cap Sheet (FR), self -adhered.
Deck: Min. 19/32-inch plywood o meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: One (1) or two (2) layers ASTM D226, Type II felt
Fasteners: 11 ga. x 1.25-inch long x 11inch head diameter round metal cap nails
Spacing: 6-inch o.c. at the 3-inch wide side laps and 12-inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt.
Deck:
Min. 19/32-inch plywood
Base Sheet:
One (1) layer ASTM D226,
Fasteners:
11 ga. x 1.25-inch x 3/8-in
Spacing:
4-inch o.c. at the 2-inch w
Base Ply:
(Optional; for use with sel
Underlayment: Polystick TU P, Polystick T
Mule -Hide SA-APP Cap Sh
Deck:
Min. 19/32-inch plywood
Base Sheet:
Two (2) layers ASTM D221
Fasteners:
it ga. x 1.25-inch long x
Spacing:
9-inch o.c. at the 2-inch H
Base Ply:
(Optional; for use with se
Underlayment:
Polystick TU P, Polystick 1
Mule -Hide SA-APP Cap SF
asphalt.
#12 Maximum Design Pressure = -45 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top suIrface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 9-inch o.c. at the 2-inch wide side laps and 18-inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#13 Maximum Desien Pressure = -52.5 n-&
meet project requirements to satisfaction of Authority Having Jurisdiction.
ype II felt
i head diameter annular ring shank roofing nails at 1-5/8-inch diameter tin caps
e side laps and 4-inch o.c. at two (2) equally spaced staggered center rows.
adhering underlayment only) Polystick MTS or Polystick MTS PLUS, self -adhered.
Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
1(FR), self -adhered or Elastoflex G TU, applied in full mopping of hot asphalt.
meet project requirements to satisfaction of Authority Having Jurisdiction.
Type II felt
3-inch head diameter annular ring shank roofing nails at 1-5/8-inch diameter tin caps
le side laps and 9-inch o.c. at two (2) equally spaced staggered center rows.
adhering underlayment only) Polystick MTS or Polystick MTS PLUS, self -adhered.
Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
?t (FR), self -adhered or Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 9-inch o.c. at the 2-inch wide side laps and 12-inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastofli x S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#14 Maximum Design Pressure = -52.5 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase or Mule -Hide Nail Base (poly -film top surface)
Fasteners: Simplex Original Cap Nailsl
Spacing: 6-inch o.c. at the 3-inch wide side laps and 6-inch o.c. at four (4) equally spaced staggered center rows.
Base Ply: (Optional) Polystick MTS or Polystick MTS PLUS, self -adhered.
Underlayment: Polystick TU P, Polystick TU Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
Mule -Hide SA-APP Cap Sheet (FR), self -adhered.
I
MEMO ETC, I.I.C. Evaluation Report P12060.02.09-R24
Certificate ofAuthorization #32455 6'" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 8 of 14
ONE M1
O I etc.
#15
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex Original Cap Nails
Spacing: 6-inch o.c. at the 3-inch ide side laps and 6-inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastof ex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#16 Maximum Design Pressure = -60 psf:
Deck: Min. 19/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: 11 ga. x 1.25-inch long x 3/8-inch head diameter annular ring shank roofing nails at 1-5/8-inch diameter tin caps
Spacing: 8-inch o.c. at the 4-inch villiide side laps and 8-inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#17 Maximum Design Pressure = -60 psf:
Deck: Min. 19/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: OMG #12 Standard Roofgrip with OMG Flat Bottom Metal Plates
Spacing: 12-inch o.c. at the 4-inch wide side laps and 12-inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#18 Maximum Design Pressure = -67.5 psf:
Deck: Min. 15/32-inch plywood i o meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Polyglass G2 Base or Polyglass APP Base (requires use of torch -applied underlayment)
Fasteners: 12 ga. x 1.25-inch long x 30-inch head diameter annular ring shank roofing nails at 1-5/8-inch diameter tin caps
Spacing: 8-inch o.c. at the 4-inch wide side laps and 8-inch o.c. at four (4) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elast ilex S6 G, applied in full mopping of hot asphalt or torch -applied or Polyflex G, torch -
applied.
#19 Maximum Design Pressure = -75 psf:
#20 Maximum Design Pressure = -90 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: Simplex MAXX Cap Fasteners
Spacing: 6-inch o.c. at the 2-inch wide side laps and 6-inch o.c. at two (2) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
#21 Maximum Design Pressure = -90 psf:
Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
Fasteners: OMG #12 Standard Roofgrip or OMG #14 Heavy Duty with OMG 3" Round Metal Plates or OMG Flat Bottom Metal
Plates
Spacing: 6-inch o.c. at the 4-inch wide side laps and 6-inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
Deck: Min. 15/32 inch plywood
to meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Polyglass G2 Base or Polyg
Fasteners: Dekfast #14 with Dekfast
OMG Flat Bottom Plates
lass APP Base (requires use of torch -applied underlayment)
Hex plates, OMG #14 HD with OMG 3" Galvalume Steel Plates, OMG Roofgrip #14 with
(AccuTrac), Trufast HD with Trufast 3-inch Insulation Plates or Simplex MAXX Cap
Fasteners
Spacing: 10 inch o.c. at the 4 inch
Underlayment: Elastoflex G TU or Elasto
wide side laps and 10-inch o.c. at three (3) equally spaced staggered center rows.
flex S6 G, applied in full mopping of hot asphalt or torch -applied or Polyflex G, torch -
applied.
#22 Maximum Design Pressure = -90 psf:
o
Deck: Min. 15/32-inch plywood meet project requirements to satisfaction of Authority Having Jurisdiction.
Base Sheet: Elastobase (sanded top surface)
Fasteners: Trufast #12 DP or Trufast 414 HD with Trufast 3" Metal Insulation Plates
Spacing: 6-inch o.c. at the 4-inch wide side laps and 6-inch o.c. at three (3) equally spaced staggered center rows.
Underlayment: Elastoflex G TU or Elastoflex S6 G, applied in full mopping of hot asphalt.
NEMO ETC, U.C. Evaluation Report P12060.02.09-R24
Certificate of Authorization #32455 6"' EDIT ON (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass
Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 9 of 14
#23 Maximum Design Pressure = -90 nsf:
Deck: Min. 15/32-inch plywood)
Base Sheet: Polyglass G2 Base or Poly(
Fasteners: Dekfast #14 with Dekfast�
OMG Flat Bottom Plate,
Fasteners
Spacing: 9-inch o.c. at the 4-inch vu
Underlayment: Elastoflex G TU or Elastc
applied.
#24 Maximum Design Pressure = -97.5 osf
Deck:
Min. 19/32-inch plywood
Base Sheet:
Elastobase or Mule -Hide
Fasteners:
11 ga. x 1.25-inch x 3/8-ir
Spacing:
4-inch o.c. at the 4-inch v
Base Ply:
(Optional) Polystick MTS
Underlayment: Polystick TU P, Polystick.
Mule -Hide SA-APP Cap SF
#25
Maximum Design Pressure = -105 psi
Deck: Min. 15/32-inch plywood
Base Sheet: Elastobase (sanded top si
Fasteners: Simplex MAXX Cap Fastei
Spacing: 6-inch o.c. at the 2-inch v
Underlayment: Elastoflex G TU or Elastof
#26
Maximum Design Pressure = -112.5 1
Deck: Min. 19/32-inch plywood
Base Sheet: Elastobase or Mule -Hide
Fasteners: 11 ga. x 1.25-inch x 3/8-ir
Spacing: 6-inch o.c. at the 4-inch v
Primer: PG100 or ASTM D41 prim
Base Ply: Polystick MTS or Polysticl
Underlayment: Polystick TU P, Polystick'
Mule -Hide SA-APP Cap S1
#27
Maximum Design Pressure = -120 psi
Deck: Min. 15/32-inch plywood
Base Sheet: Elastobase (sanded top si
Fasteners: CMG #12 Standard Roof
Plates
Spacing: 6-inch o.c. at the 4-inch vi
Underlayment: Elastoflex G TU or Elastof
#28
Maximum Design. Pressure = -120 psi
Deck: Min. 15/32-inch plywood
Base Sheet: Elastobase (sanded top si
Fasteners: Trufast #12 DP or Trufast
Spacing: 6-inch o.c. at the 4-inch v
Underlayment: Elastoflex G TU or Elastof
5.6.4.1
All other direct -deck, adhered Poly
Design Pressure of -45 psf.
ONEMOletc.
:o meet project requirements to satisfaction of Authority Having Jurisdiction.
lass APP Base (requires use of torch -applied underloyment)
Hex plates, CMG #14 HD with OMG 3" Galvalume Steel Plates, OMG Roofgrip #14 with
(AccuTrac), Trufast HD with Trufast 3-inch Insulation Plates or Simplex MAXX Cap
le side laps and 9-inch o.c. at four (4) equally spaced staggered center rows.
ex S6 G, applied in full mopping of hot asphalt or torch -applied or Polyflex G, torch-
o meet project requirements to satisfaction of Authority Having Jurisdiction.
ail Base (poly -film top surface)
:h head diameter annular ring shank roofing nails at 1-5/8-inch diameter tin caps
de side laps and 4-inch o.c. at four (4) equally spaced staggered center rows.
r Polystick MTS PLUS, self -adhered.
J Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
!et (FR), self -adhered.
meet project requirements to satisfaction of Authority Having Jurisdiction.
ice for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
a side laps and 6-inch o.c. at three (3) equally spaced staggered center rows.
S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
o meet project requirements to satisfaction of Authority Having Jurisdiction.
ail Base (poly -film top surface)
:h head diameter annular ring shank roofing nails at 1-5/8-inch diameter tin caps
de side laps and 6-inch o.c. at four (4) equally spaced staggered center rows.
r at all tin -caps
MTS PLUS, self -adhered
J Plus, Polystick TU Max, Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and
!et (FR), self -adhered.
meet project requirements to satisfaction of Authority Having Jurisdiction.
ice for hot -asphalt or torch -applied cap or poly -film surface for torch -applied cap)
or OMG #14 Heavy Duty with OMG 3" Round Metal Plates or OMG Flat Bottom Metal
side laps and 6-inch o.c. at five (5) equally spaced staggered center rows.
S6 G, applied in full mopping of hot asphalt or Polyflex G, torch -applied.
meet project requirements to satisfaction of Authority Having Jurisdiction.
4 HD with Trufast 3" Metal Insulation Plates
side laps and 6-inch o.c. at five (5) equally spaced staggered center rows.
S6 G, applied in full mopping of hot asphalt.
underlayment systems beneath foam -on tile systems carry a Maximum
NEMO ETC, I.I.C. Evaluation Report P12060.02.09-R24
Certificate ojAuthorization #32455 6T" EDITIION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 10 of 14
*NEMO I etc.
5.6.4.2 For mechanically attached Base Sheet, the maximum design pressure for the selected assembly shall meet or exceed
that required under FRSA/TRI April 2�012 (04-12), Appendix A, Table 1A.
Alternatively, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design
pressure determined in accordance with FBC 1609. In this case, Zones 2 and 3 shall employ an attachment density
designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are
ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29 and Roofing Application Standard RAS 117. Assemblies marked
with an asterisk* carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (January
2016) for Zone 2/3 enhancements.
5.7 Exposure Limitations:
Elastobase, Elastobase P, Polyglass G2 Base or Polyglass APP Base shall not be left exposed for longer than 30-days
after installation.
Polystick IR-Xe or Polystick MU-X shall) not be left exposed for longer than 90-days after installation.
Polystick MTS, MTS PLUS, TU P, TU Plus, TU Max, Dual Pro, Tile Pro or Elastoflex G TU shall not be left exposed for
longer than 180-days after installation.
Polyflex SAP or SAP FR, or Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) does not have an exposure
limitation, unless the prepared roof covering is to be adhesive -set tile, in which case the maximum exposure is 30
days.
Elastoflex S6 G or Elastoflex S6 G FR or Polyflex G or Polyflex G FR does not have an exposure limitation, unless the
prepared roof covering is to be adhesive -set tile (Elastoflex S6 G or Polyflex G only), in which case the maximum
exposure is 180 days.
5.8 Polystick MU-X has been found through comparative testing to have a lesser coefficient of friction than ASTM D226
roofing felt in a dry condition, tested at standard laboratory conditions. Agreement between purchaser and seller, as
set forth in Section 4.3, Note 1 of AS IM D1970-15, should be established as to slip resistance.
5.9 Tile Slippage Limitations (FRSA/TRI April 2012 (04-12))•
When loading roof tiles on the underlayment in direct -deck tile assemblies, the maximum roof slope shall be as
follows. These slope limitations can only be exceeded by using battens during loading of the roof tiles.
TABLE 2: TILE SLIPPAGE LIMITATIONS FOR DIRECT -DECK TILE' INSTALLATIONS
Underlayment
Tile Profile
Staging Method
Maximum Slope
Elastoflex G TU
Flat
10-tile stack
7:12
Lugged
8-tile stack (6 over 2)
6:12
Elastoflex 56 G or S6 G FR
Flat orl Lugged
6-tile stack (4 over 2)
4:12
Polystick MTS or MTS PLUS
Flat
6-tile stack (4 over 2)
5:12
Lugged
6-tile stack (4 over 2)
4:12
Polystick Tile Pro
Flat orlLugged
6-tile stack (4 over 2)
7:12
Polystick TU Max
Flat
6-tile stack (4 over 2) or 10-tile stack
7:12
Lugged
6-tile stack (4 over 2)
7:12
Lugged
10-tile stack
6:12
Polystick TU P
Flat
6-tile stack (4 over 2)
6:12
Lugged
6-tile stack (4 over 2)
4:12
Polystick TU Plus
Flat or
(Lugged
6-tile stack (4 over 2)
7:12
Flat or
ILugged
10-tile stack
6:12
Polyflex G or G FR
Flat or
ILugged
6-tile stack (4 over 2)
4:12
Polyflex SA P or SA P FR
Flat or Lugged
6-tile stack (4 over 2)
4:12
NEMO ETC, I.I.C.
Certificate of Authorization #32455
6"' EDIT ON (2017) FBC NON-HVHZ EVALUATION
Polygla s Roof Underlayments; (954) 233-1230
Evaluation Report P12060.02.09-R24
FL5259-R28
Revision 24: 01�24/2018
Page 11 of 14
OMEMO I etc.
6. INSTALLATION:
6.1 Polyglass Roof Underlayments shall be installed in accordance with Polyglass published installation requirements
subject to the Limitations set forth inlI Section 5 herein and the specifics noted below.
6.2 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove
any dust and debris prior to application, and prime the substrate (if applicable).
6.3 Elastobase,.Elastobase P or Mule-HideF.Nail'' Base:
6.3.1 Non -Tile Applications:
Shall be installed in compliance with the codified requirements for ASTM D226, Type II underlayment in FBC Table
1507.1.1 for the type of prepared roof covering to be installed.
Elastobase, Elastobase P or Mule -Hide Nail Base may be covered with a layer of Polystick, Polyflex SAP, Polyflex SA
P FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR), self -adhered, Elastoflex G TU, Elastoflex S6 G or
Elastoflex S6 G FR in hot asphalt or Polyflex G or Polyflex G FR, torch applied. Roof cover limitations are those are
those associated with the top -layer uInderlayment, as set forth in Table 1.
6.3.2 Tile Applications:
Elastobase, Elastobase P or Mule -Hide Nail Base are limited to use as a mechanically attached base sheet in the "Two
Ply System" from FRSA/TRI April 2012 (04-12). Reference is made to Table 1 and Section 5.6.4 herein, coupled with
FRSA/TRI April 2012 (04-12) Installation Manual.
6.4 Polystick MTIS,`.MTS PLUS, IR-Xe, TU P, TU Plus, TU Max,Dual, Pro, Tile Pro or MU-X or Polyflex SAP, Polyflex SAP FR,
Mule Hide SA-APP Cap Sheet or Mule -Hide SA-APP: Cap. Sheet (FR):
6.4.1 Shall be installed in compliance with the codified requirements for ASTM D1970 (except Polystick TU P) underlayment
in FBC Table 1507.1.1 for the type of prepared roof covering to be installed.
6.4.2 Direct -to -Deck with Mprhanirnlly Factpnorl Rnnf rn„orc-
All self -adhering materials, with the
Cap Sheet or SA-APP Cap Sheet (FR)
Hide back nailing guidelines. Nails
diameter metal disk or Simplex -type
nailed using the above noted faster
membrane. The head lap membrane
All seal -lap seams (selvage laps)
firmly rolled with a minimum 28
roller to ensure full contact and adhe
:ception of Polystick TU Plus, Polyflex SAP or SAP FR and Mule -Hide SA-APP
ould be back -nailed in selvage edge seam in accordance with Polyglass / Mule -
all be corrosion resistant, 11 gauge ring -shank type with a minimum 1-inch
eta[ cap nail, at a minimum rate of 12" o.c. Polystick TU Plus should be back-
rs and spacing, in area marked "nail area, area para clavar" on the face of
to cover the area being back -nailed.
lust be
I. hand
on.
For Dual Pro and Tile Pro, align the edge of
the top sheet to the end of the glue pattern
(the sheet will overlap the fabric).
View of Ovelap Seam of Dual Pro and Tile Pro
All over -fabric and over -granule end -laps shall have a 6-inch wide, uniform layer of Polyplus 50 Premium Modified
Wet/Dry Cement or Polyglass PG500 Modified Cement applied in between the application of the lap.
Polystick TU Plus, Dual Pro and Tile Pro may not be used in any exposed application such as crickets, exposed valleys,
or exposed roof to wall details
NEMO ETC, LLC.
Certificate of Authorization #32455
6T" EDITION (2017) FBC NON-HVHZ EVALUATION
Polyglass Roof Underlayments; (954) 233-1230
Evaluation Report P12060.02.09-R24
FL5259-R28
Revision 24: 01/24/2018
Page 12 of 14
Repair of Polystick membranes is to
Polyglass PG500 Modified Cement
Polystick material of like kind, set
installed in a water shedding manne
All Polystick membranes shall be i
minimum of 40-lb weighted -roller c
for the field membrane. Hand roller
roof that are not accessible to a larR
6.4.3 Tile Applications (not allowed for A
Reference is made to FRSA/TRI Al
noted above as a guideline.
For mechanically fastened tile roofi
Sheet fastening shall be not less tha
For adhesive -set tile applications, re
6.4.4 Two (2) Ply Und'erlavment Systems:
Polystick MTS or MTS PLUS followe
SAP is allowable for use under mec
the top -layer material. This is not a
Polystick MTS or MTS PLUS followe
under foam -on tile systems. Limits
but is allowable if a 2-plv underlavrr
14NEMO I etc.
)e accomplished by applying Polyplus 50 Premium Modified Wet/Dry Cement or
to the area in need of repair, followed by a minimum 6 x 6 inch patch of the
Ind hand rolled in place over the repair area. Patch laps, if needed, shall be
istalled to ensure full contact with approved substrates. Polyglass requires a
on steep slopes, use of a stiff broom with approximately 40-lbs of load applied
are acceptable for rolling of patches, laps (min. 28 lb roller) or small areas of the
roller or broom.
2012 (04-12) Installation Manual and Table 1 herein, using the instructions
over 2-ply system, consisting of Base Sheet and self -adhering top sheet(s), Base
FRSA/TRI April 2012 (04-12), Table 1.
!r to Section 5.6.4 herein.
by Polystick MTS, MTS PLUS, TU P, TU Plus, TU Max, Tile Pro, MU-X or Polyflex
nically attached prepared roof systems. Limits of use are those associated with
!quirement, but is allowable if a 2-ply underlayment system is desired.
by Polystick TU P, TU Plus, TU Max, Tile Pro or Polyflex SAP is allowable for use
use are those associated with the top -layer material. This is not a requirement,
ent system is desired.
6.5 Elastoflex G TU, Elastoft6x'S6 G,or •E'lastoflex S6 G'FR: .
6.5.1 Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FIR shall be installed in compliance with current Polyglass published
installation requirements. For use in tile applications:
✓ Elastoflex G TU is for use as an ialternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single
Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems or the Hot Asphalt
applied "Cap Sheet" in the "Twos Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened or
adhered tile roof systems.
✓ Elastoflex S6 G is for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single Ply
System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems or the Hot Asphalt
applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened or
adhered tile roof systems.
✓ Elastoflex S6 G FIR is for use as ain alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single
Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems or the Hot Asphalt
applied "Cap Sheet" in the 'Twol Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened the
roof systems.
6.5.2 For hot -asphalt -applications, Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FIR shall be fully asphalt -applied to the
substrates noted in Section 5.6. iSide laps shall be minimum 3-inch and end -laps minimum 6-inch wide, off -set
minimum 3 feet from course to course. Side and end laps shall be fully adhered in a complete mopping of hot asphalt
with.asphalt extending approximately 3/8-inch beyond the lap edge.
16 C,., Polyflex G„or.Polyflex G-FR:,
6.6.1 Polyflex G or Polyflex G FIR shall be' installed in compliance with current Polyglass published installation requirements.
For use in tile applications:
✓ Polyflex G is for use as an alternate to the Heat Applied "Cap Sheet" in the 'Two Ply System" from FRSA/TRI April
2012 (04-12) beneath mechanically fastened or adhered tile roof systems (Base Sheet Limited per 5.6.3).
✓ Polyflex G FIR is for use as an alternate to the Heat Applied "Cap Sheet" in the 'Two Ply System" from FRSA/TRI
April 2012 (04-12) beneath mechanically fastened tile roof systems (Base Sheet Limited per 5.6.3).
NEMO ETC, LLC. Evaluation Report P12060.02.09-R24
Certificate of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 13 of 14
ONEMO I etc.
6.6.2 Polyflex G or Polyflex G FR shall bie fully torch -applied to the substrates noted in Section 5.6. Side laps shall be
minimum 3-inch and end -laps minimum 6-inch wide, off -set minimum 3 feet from course to course. Side and end
laps shall be fully heat -welded and inspected to ensure minimum 3/8-inch flow of modified compound beyond the lap
edge.
6_7 Tile Staging:
6.7.1 Tile shall be loaded and staged in a manner that prevents tile slippage and/or damage to the underlayment. Refer to
Table 2 herein, and Polyglass publish ed requirements for tile staging.
6.7.2 Battens and/or Counter -battens, as rIIequired by the tile manufacturer and FRSA/TRI April 2012 (04-12) must be used
on all roof slopes greater than 7:12. Precautions should be taken as needed, such as the use of battens or sail-
boards, to prevent tile sliding and/or damage to the underlayment during the loading process.
6.7.3 Polyglass specifies the minimum cure time after installation of self -adhering membranes and before loading of
roofing tiles is forty-eight (48) hours.
7. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority' Having Jurisdiction in order to properly evaluate the installation of this product.
8. MANUFACTURING PLANTS:
Contact the noted QA agency for information on product locations covered for F.A.C. 61G20-3 QA requirements. The following
plants have qualified products under their respective physical properties specifications.
9.
Plant
Specification
Product s
Fernley, NV, Hazleton, PA & Winter Haven, FL
ASTM D1970
Polystick MU-X
Hazleton, PA
M-D 13-0004
Elastoflex G TU
Hazleton, PA & Winter Haven, FL
ASTM D1970
Polystick IR-Xe
ASTM D1970 & FRSA/TRI April 2012
Polystick TU Plus
ASTM D1970 & FRSA/TRI April 2012
Polystick TU Max
Tuscaloosa, AL
ASTM D4601, Type II
Polyglass G2 Base
Winter Haven, FL
ASTM D226 (physicals)
Elastobase, Elastobase P
ASTM D6509
Polyglass APP Base
FRSA/TRI April 2012
Polystick MTS, Polystick MTS PLUS
FRSA/TRI April 2012
Polystick TU P
FRSA/TRI April 2012
Polyflex SAP, Polyflex SA P FR
ASTM D1970
Polystick Dual Pro
ASTM D1970 & FRSA/TRI April 2012
Polystick Tile Pro
ASTM D6164
Elastoflex S6, Elastoflex S6 G FR
ASTM D6222
Polyflex G, Polyflex G FR
L4UALIIY AbbUKANGh CNTITY:
UL, LLC—QUA9625; (314) 578-3406; k.chancelloi@us.ul.com
-E ND OF EVALUATION REPORT -
NEMO ETC, I.I.C.
Certificate of Authorization #32455
6T" EDITION (2017) FBC NON-HVHZ EVALUATION
Polyglass Roof Underlayments; (954) 233-1230
Evaluation Report P12060.02.09-R24
FL5259-R28
Revision 24: 01/24/2018
Page 14 of 14