HomeMy WebLinkAboutNOA ROOF DECK PROTECTIONd•
MM 9.0
Cflt1CyT1
DEPARTMENT OF REGULATORY AND ECONOMIC RES6URCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTICE OF ACCEPTANCE (NOA
GAF
1 Campus Drive
Parsipanny, NJ 07054
MIAMI-DADE COUNTY
PRODUCT' CONTROL SECTION
11805 SW 26 Street, Room 208
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
www.misn idade.gov/economy
SCOPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their j urisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
j
DESCRIPTION: GAF Leak Barriers and Roof Deck Protection
1
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This NOA renews and revises NOA 16-1213.04 and consists of pages 1 through 10.
The submitted documentation was reviewed by Hamley Pacheco, P.E.
FILE
t1- �:t� 1`•
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page I of 10
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Underlayment
Material: SBS/Polypropylene/Asphal
PRODUCTS DESCRIPTION:
Product
WeatherWatch® Mineral
Surfaced. Leak Barrier
Manufacturing
Location #1, 9
StormGuarda Film
Surfaced Leak Barrier
Manufacturing
Location #1, 9
Dimensions
36" x 50' rolls
36" x 66.7' rolls
36" x 66.7' rolls
LibertyTM SBS Self- '
39'/8" x 66' rolls
Adhering Base/Ply Sheet
Manufacturing
Location #l, 9
Deck-ArmorT" Premium
54" x 222' rolls
Breathable Roof Deck
48".x 100' rolls
Protection
Manufacturing
Location #2
Tiger PawTM Roof Deck
48" x 250' rolls
Protection
48" x 100' rolls
Manufacturing
Location #3, 5, 6
rac
Fel t
cr z
a r,
Shingle -Mate® Roof Deck 36" x 144' rolls
Protection
Manufacturing
Location #4
MI�AMI-DADE CO11
UNTY
ASTM D 1970
I
ASTM D 1970
ASTM D 1970
ASTM ID4601
Typie II
ASTMI D 226
Type 11
ASTM D 226
Type 11
Product
Description
Granular surfaced modified, fiberglass reinforced,
bite vinous sheet material for use as a leak barrier
underlayment in sloped roof assemblies.
Designed as an ice & rain shield.
Modified, fiberglass reinforced, bituminous sheet
material for use as a high temperature leak barrier
underlayment in sloped roof assemblies.
Designed as an ice & rain shield.
Self -adhering SBS roof membrane.
A.UV=stabilized polypropylene breathable
underlayment. To be used for roof deck
protection as an underlayment in sloped roof
assemblies.
A UV -stabilized polypropylene non -breathable
underlayment. To be used for roof deck protection
as an underlayment in sloped roof assemblies.
26 ,.-A-UV stabilizedTolypyxopylone;rnon;breathable
n�fw
I uiWWraymerit To be used for roof deck protection
A a wid-eh U3aW" Yroofassemblies.
ASTM D 226 Fibergass-reinforced asphalt felt underlayment. To
Type I be used for roof deck protection as an
underlayment in sloped roof assemblies.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 2 of 10
PRODUCTS DESCRIPTION: I
Test
Product
Product
Dimensions
Specification
Description
LibertyT" SA Class Crap
393/8,, x 34' rolls
ASTM D 1970
Granular surfaced modified, fiberglass reinforced,
Sheet
ASTM D 6163
self -adhering SBS roof membrane.
Manufacturing
Location # 9
ASTM D 7530
GAFGLAS® Ply 4
39.37"
ASTM 132178
Aspahalt impregnated glass felt with aspahlt
Manufacturing
(1 meter) Wide
Type 1V
coating.
Location # 9, 10
i
GAFGLAS® Flex.PlyTD1 6
39.37"
ASTM 62178
Aspahalt impregnated glass felt with aspahlt
Manufacturing
(1 meter) Wide
Type!V1
coating.
Location # 9, 10
MANUFACTURING LOCATION:
l.Mt. Vernon, IN
2.North Bay, Ontario
3.Mission, British Columbia
4.Pryor, OK
5.Qingdao, China
6.Charleston, SC
7.Spartanburg, SC
8.Dadra, India
9.Savannah, GA
IO.Mobile, AL
NOA No.: 18-0119.15
MIAMI•DAOE COUNTY
. , , E a� Expiration Date: 02/22/23
Ij Approval Date: 02/22/18
Page 3 of 10
EVIDENCE SUBMITTED:
Test Agency
Intertek Testing Services NA Ltd.
PRI Construction Materials
Technologies, LLC.
Trinity-ERD
Test Identifier
Test Name/Report
Date
3077464-01
ASTM D 1970
08/23/06
3090131 i
Wind Uplift and Self Seal ability
08/23/06
100258583COQ-6IOA
ASTM D 226 Type 11
01/08/11
100673818COQ '003
ASTM D 226 Type II
06/13/13
10157289000Q ,005
ASTM D 226 Type 11
04/17/14
F8549.02-106-;18
ASTM D 226 Type 1
11/08/16
RGM-023-02-01
ASTM D 4798
05/16/07
GAF-1 12-02-01
ASTM D 226 Type 11
03/15/06
GAF-238-02-01
ASTM D 1970
03/03/10
GAF-323-02-01
ASTM D 1970
11/30/11
GAF-324-02-01
ASTM D 1970
12/01/11
GAF-325-02-61
ASTM D 1970
12/01/11
GAF-326-02-01
ASTM D 1970
11/30/11
GAF-275-02-01
ASTM D 1970
1 1/11/10
GAF-344-02-01
ASTM D 1970
04/23/12
GAF-339-02-01
ASTM D 226 Type 1
03/14/12
ELK-311-02-61
ASTM D 1970
09/11/07
GAF-518-02-01
ASTM D 226 Type 1
06/04/14
GAF-818-02-01
ASTM D 4533
12/06/17
GAF-829-02-01
ASTM D 226 Type 11
01/15/18
GAF-314-02-01
ASTM D 2178
07/21/11
GAF-315-02-01
ASTM D 2178
07/21/11
GAF-SC13285.03.17-1
ASTM D 1970
03/08/17
GAF-SC13285.03.17-3
ASTM D 1970
03/01/17
GAF-SC13285.03.17-4
ASTM D 1970
03/01/17
GAF-SC13285.02.17-2
ASTM D 4601 Type 11
02/08/17
GAF-SC9700.081 15-R1
ASTM D 2178
09/09/15
GAF-SC12915.12.17-R1
ASTM D 1970
12/11/17
GAF -SC I2915.12.17-R1
ASTM D 6163
12/11/17
GAF-SC12915.12.17-RI
ASTM D 7530
12/11/17
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 4 of 10
APPROVED ASSEMBLIES:
Deck Type 1: Wood, non -insulated
Deck Description: " 3z" or greater plywood or wood plank
System E (1): Anchor sheet mechanically fastened Ito deck, membrane adhered.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle -Mate' Roof Deck Protection OR one or more plies
of ASTM D 226 Type II, Deck-ArmorTM Premium Breathable Roof Deck Protection, FeltBustere
High -Traction Synthetic Roofing Felt, or Tiger PawTM Roof Deck Protection with a minimum 4"
side lap and a 6" end lap mechanically fastened to the deck with approved nails and tin caps 6"
o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape,all end and side laps with approved butyl adhesive based
scam/cover tape or an approved waterproof cloth duct tape (follow the tape's manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
Membrane: One or more plies of WeatherWatcli® Mineral Surfaced Leak Barrier, StormGuardo Film
Surfaced Leak Barrier, LibertyT"' SA Glass Cap Sheet, or LibertyT11' SBS Self -Adhering
Base/Ply Sheet membrane with a minimiun 3" side lap and 6'' end lap. Place the first course of
membrane parallel to the cave, rolling the membrane to obtain maximum contact. Remove the
release membrane as the membrane!is applied. Vertical strapping of the roof with
WeatherWatch® Mineral Surfaced Leak Barrier, or StormGuard',Film Surfaced Leak Barrier is
acceptable.
Surfacing: Approved Roofing Assembly.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 5 of 10
Deck Type l: Wood, non -insulated
Deck Description: 1 62" or greater plywood or wood plank
System E(2): Membrane mechanically fastened to deck.
Separator Sheet: One or more plies of GAFGLASO" Ply 4, GAFGLAS'FlexPly"" 6, Shingle -Mate' Roof'Deck
Protection, Deck-ArmorTM Premium Breathable Roof Deck Protection, FeltBuster® High -
Traction Synthetic Roofing Felt, or Tiger PawTM Roof Deck Protection loose laid.
Membrane: One or more plies of WeatherWatchP Mineral Surfaced Leak Barrier, StormGuard® Film
Surfaced Leak Barrier, LibertyT1111 Sn Glass Cap Sheet, or LibcrtyTM SBS Self -Adhering
Base/Ply Sheet membrane mechanically fastened with a minimum 3" side lap and a. 6" end lap to
deck through the separator sheet with approved nails and tin caps 6" o.c. at the laps and two
staggered rows 12" o.c. in the field of the roll.
Surfacing: Approved Roofing Assembly.
CMIAMI-MOUNTY NOA No.: 18-0119.15
VI . , ., 7I Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 6 of 10
Deck Type 1: Wood, non -insulated
Deck Description: 19/32" or greater'plywood or wood plank
System E (3): Anchor sheet mechanically fastened to deck, membrane adhered.
Secondary Water Install a minimum 4" wide WeatherWatch® Mineral Surfaced Leak Barrier, , LibcrtyTm SBS
Barrier: Self -Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, or StormGuard' Film Surfaced
(Optional) Leak Barrier membrane over the joints of the plywood roof deck prior to installation of the base
sheet. Do not overlap end or side joints. All side and end laps should be butted firmly side by
side, flush with each other but not overlapped. Do not leave the WeatherWatch' Mineral
Surfaced Leak Barrier, or StormGuard® Film Surfaced Leak Barrier membrane exposed for more
than 30 days without a roof deck protection underlayment protecting the secondary water barrier.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle -Mate® Roof Deck Protection OR one or more plies
of ASTM D 226 Type 11, Deck-ArmorT"' Premium Breathable Roof Deck Protection,
FeltBuster' High -Traction Synthetic iRoofing Felt, or Tiger PawTM Roof Deck Protection with a
minimum 4" side lap and a 6".end lap mechanically,iastcned to the deck with approved nails and
tin caps 6" o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
seanifcover tape or an approved wate'rpioof cloth duct tape (follow the tape manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fasteners.
Surfacing: Approved Roofing Assembly.
NOA No.: 18-0119.15
MIQMI LlAO± COtjrgT Y Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 7 of 10.
Deck Type 1: Wood, non -insulated
Deck Description: 19/32" or greater plywood or wood plank
System E (4): Anchor sheet mechanically fastened to deck, membrane adhered.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle -Mateo Roof Deck Protection OR one or more plies
of ASTM D 226 Type II, Deck -Armor"' Premium Breathable Roof Deck Protection,
FeltBustero High -Traction Synthetic Roofing Felt, or Tiger PawT' Roof Deck Protection with a
111inmlllnl 4" side lap and a 6" end lap mcchanical!_v fastened to the deck with approved nails and
tin caps 6" o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
I
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
scans/cover tape or an approved waterproof cloth duct tape (follow the tape's manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
Membrane: One or more plies of StormGuard® Film Surfaced Leak Barrier membrane with a minimum 4"
side lap and 6" end lap. Place the fiat course of iembrane parallel to the eave, rolling the
membrane to obtain maximum contact. Remove the release membrane as the membrane is
applied.
Surfacing: Approved for Metal roofing, Slate, and Asphalt Shingle assemblies.
NOA No.: 18-0119.15
MIAMIEMM 411 Expiration Date: 02/22/23
Approval Date: 02/22/18
j Page 8 of 10
LIMITATIONS:
1. Fire classification is not,part of this acceptance.
2. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard' Film Surfaced Leak Barrier, Liberty"" SBS Self -
Adhering Base/Ply Sheet, Liberty'•"' SA Glass Cap Sheet, Shingle -Mate° Roof Deck Protection, Deck -Armor"
Premium Breathable Roof Deck Protection, FeltBuster' High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection shall not be used as roof tile underlayment.
3. This acceptance is for prepared roofing applications. ' Minimum deck requirements shall be in compliance with
applicable building code. WeatherWatch' Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak
Barrier, Liberty"" SBS Self -Adhering Base/Ply Sheet,! Liberty''"' SA Glass Cap Sheet, Shingle -Mateo Roof Deck
Protection, Deck-ArmorTM Premium Breathable Roof Deck Protection, FeltBuster° High -Traction Synthetic
Roofing Felt, and Tiger PawTM Roof Deck Protection shall be installed in strict compliance with applicable
Building Code.
4. WeatherWatch' Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyT" SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Shect, Shingle -Mate° Roof Deck Protection, Deck-ArmorTM
Premium Breathable Roof Deck Protection, FeltBuster° High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection membranes shall be applied! to a smooth, clean and dry surface with deck free of
irregularities.
5. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard' Film Surfaced Leak Barrier, Liberty'*"' SBS Self -
Adhering Base/Ply Sheet, LibertyT,"I SA Glass Cap Sheet, Shingle -Mate' Roof Deck Protection, Deck-Armor"m
Premium Breathable Roof Deck Protection, FeltBuster° High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection membranes shall not be applied over an existing roof membrane.
6. WeatherWatch' Mineral Surfaced Leak Barrier, StormGuardl Film Surfaced Leak Barrier, Liberty"'"' SBS Self -
Adhering Base/Ply Sheet, Liberty''" S.A Glass Cap Sheet, Shingle -Mate" Roof Deck Protection, Deck-ArmorTM
Premium Breathable Roof Deck Protection, FeltBuster° High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection shall not be left exposed as a temporary roof for longer than 30 days of application.
7. WeatherWatch' Mineral Surfaced Leak Barrier, StormGuard' Film Surfaced Leak Barrier, Liberty'-"' SBS Self -
Adhering Base/Ply Sheet, Liberty"'"' SA Glass Cap Sheet, Shingle -Mate° Roof Deck Protection, Deck-Armor"M
Premium Breathable Roof Deck Protection, FeltBuster° High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection may be used with any approved roof covering Notice of Acceptance listing WeatherWatch®
Mineral Surfaced Leak Barrier, StormGuard' Film Surfaced Leak Barrier, LibertyT"'' SBS Self -Adhering Base/Ply
Sheet, LibertyT" SA Glass Cap Sheet, Shingle -Mate 0- Roof Deck Protection, Deck-ArmorTM Premium Breathable
Roof Deck Protection, FeltBuster° High -Traction Synthetic Roofing Felt; and Tiger PawTM Roof Deck Protection
as a component part of an assembly in the Notice of Acceptance. if WeatherWatch' Mineral Surfaced Leak
Barrier, StormGuard' Film Surfaced Leak Barrier, Liberty''"' SBS Self -Adhering Base/Ply Sheet, Liberty""" SA
Glass Cap Sheet, Shingle -Mate' Roof Deck Protection, Deck-ArmorTM Premium Breathable Roof Deck Protection,
FeltBuster° High -Traction Synthetic Roofing Felt and Tiger Paw"m Roof Deck Protection are not listed; a request
may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Department
for approval provided that appropriate documentation is provided to detail compatibility of the products, wind
uplift resistance, and fire testing results.
8. All nails in the deck shall be carefully checked for protruding heads. Re -fasten any loose decking panels. Sweep
the deck thoroughly to remove any dust and debris prior to application. Install when temperatures are 45' F and
rising.
9. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane
from the center outward in both directions.
NOA No.: 18-0119.15
MIAMb1p£ COUhaTY Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 9 of 10
LIMITATIONS:
10. Roll or broom the entire membrane surface so as to have 100% contact with the surface, giving special attention to
overlap areas.
11. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance and applicable Building Code.
12. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
13. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo,
city and state of manufacturing facility, and the following statement: "Miami -Dade County Product Control
Approved" or the Miami -Dade County Product Control Seal as shown below.
CMIAMI.MDADEWCOMUN
END OF THIS ACCEPTANCE
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 10 of 10