HomeMy WebLinkAboutNOA-ROOF UNDERLAYMENTS{ TRINITY
FWAI I IATIAIU RFPORT
ER® WkkAA hrif
Boral Roofing
7575 Irvine Center Drive, Suite 100
Irvine, CA. 92618
(602) 269-2288
SCOPE:
This Evaluation Report is issued under Rule 61G20-3
construction materials in the State of Florida. The dOCL
P.E. for use of the product under the Florida Buildin
products described herein have been evaluated for c
sections noted herein.
DESCRIPTION: Boral Roof Underlayments
LABELING: Labeling shall be in accordance with the r
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid u
Quality Assurance documentation changes, or provisior
this Evaluation Report by the named client constitut
changes or the referenced Quality Assurance documen
Evaluation Report relative to updated Code requiremer
ADVERTISEMENT: The Evaluation Report number preced
advertising literature. If any portion of the Evaluation I
INSPECTION: Upon request, a copy of this entire Evaluati
its distributors and shall be available for inspection at t
This Evaluation Report consists of pages 1 through 7.
Prepared by:
Robert.J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCA ANE1983
CERTIFICATION OF INDEPENDENCE:
1. Trinity IERD does not have, nor does it intend to acqui
distributing products it evaluates.
2. Trinity I ERD is not owned, operated or controlled by any 1
3. Robert Nieminen; P.E. does not have nor will acquire, a
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire,.a
product.
5. This is a building code evaluation. Neither Trinity ERD
project on which this Evaluation Report, or previous ver
specifically for that purpose.
EXTERIOR RESEARCH & DESIGN, LLC.
Certificate of Authorization #9503
353 CHRISTIAN STREET, UNIT#13
OXFORD, CT 06478
(203) 262-9245
Evaluation Report M35710.12.10-R9
FL14317-R8
Date of issuance:12/21/2010
Revision 9:10/14/2017
J the applicable rules and regulations governing the use of
entation submitted has been reviewed by Robert Nieminen,
Code and Florida Building Code, Residential Volume. The
npliance with the 6th Edition (2017) Florida Building Code
uirements the Accredited Quality Assurance Agency noted
A such time as the named product(s) changes, the referenced
of the Code that relate to the product change. Acceptance of
agreement to notify Robert Nieminen, P.E. if the product
tion changes. Trinity I ERD requires a complete review of this
with each Code Cycle.
i by the words "Trinity IERD Evaluated" may be displayed in
port is displayed, then it shall be done in its entirety.
i Report shall be provided to the user by the manufacturer or
job site at the request of the Building Official.
The facsimile seal appearing was authorized by Robert
Nieminen, P.E. on 10/14/2017. This does not serve as an
electronically signed document
or will it acquire, a financial interest in any company manufacturing or
npany manufacturing or distributing products it evaluates.
ancial interest in any company manufacturing or distributing products for
interest in'any other entity involved in the approval process of the
Robert Nieminen, P.E. are, in any way, the Designer of Record for any
thereof, is/was used for permitting or design guidance unless retained
/
y
4
TRINOERE)
`"
ROOFING COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: Boral Roof Underlayments, as marketed by Boral Roofing, have demonstrated compliance
with the following sections of the 6th Edition (2017) Florida Building Code through testing in -'accordance with the
following Standards. .Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set
forth herein.
2. STANDARDS:
Section
Property ' •
Standard
Year
1504.3.1
Wind Uplift
UL 1897
2012
1507.1.1, T1507.1.1, 1507.2.9.2
Physical Properties
ASTM D1970
2015
1507.3.3
Physical Properties
FRSA/TRI April 2012 (04-12)
2012
3. REFERENCES:
Entity
Examination
Reference.
Date
ERD (TST 6049)
Physical Properties
M36790.07.11
09/30/2011
ERD (TST 6049)
Physical Properties
B40380.08.12-
08/28/2012
ERD (TST 6049)
Tensile Adhesion / LTA
C41420.09.12-2
09/11/2012
ERD (TST 6049)
-Adhesion .
B41940.09.12
09/13/2012
ERD (TST 6049)
Tensile Adhesion / LTA
B47390.07.14-1
07/31/2014 .
ERD (TST 6049)
Tensile Adhesion / LTA
B47390.09.14
09/04/2014
PRI (TST5878)
ASTM D1970
NEI-031-02-02:REV
10/27/2010
PRI (TST 5878)
ASTMD1970
NEI-029-02-01:11EV
12/03/2010
PRI (TST 5878)
Tensile Adhesion / LTA
NEI-046-02-01REV
12/17/2010
PRI (TST 587.8)
FRSA/TRI April 2012
NEI-076-02-01
02/14/2011
PRI (TST 5878)
ASTM D1970 -
NEI-034-02-02
01/29/2013
PRI (TST 5878)
Wind Uplift
BORR-001-02=01
03/17/2015
PRI (TST 5878)
Wind Uplift
BORR-005-02-01
06/24/2015 .
UL, LLC. (QUA 9625)
Quality Assurance
Service Confirmation
Exp: 08/21/2020
4. PRODUCT DESCRIPTION:
4.1 Self -Adhering Underlayments:
4.1.1 Boral TileSeal® 50RT is a nominal 50-mil thick, polyester -surfaced, self -adhering SBS modified bitumen roof
underlayment; meets ASTM D1970.
4.1.2 Boral TileSeal® HT is a nominal 60-mil thick, polyester -surfaced, self -adhering SBS modified bitumen,roof
underlayment; meets ASTM D1970 and FRSA/TRI 04-12.
4.1.3 GatorSeal® is a nominal 55-mil thick, granular -surfaced, fiberglass reinforced, self -adhering SBS modified
bitumen roof underlayment; meets ASTM D1970.
4.1.4 Citadel® Plus is a nominal 48-mil thick, fabric -surfaced, fiberglass reinforced, self -adhering SBS modified
bitumen roofing underlayment for use as' a base -layer in two-ply underlayment systems; meets ASTM
D1970.
5. LIMITATIONS:
5.1 This is a buildingr code. evaluation. Neither Trinityl ERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
Exterior Research and Design, I.I.C. Evaluation Report M35710.12.10-R9
Certificate ofAuthorization #9503 67° EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-R8
Boral Roof Underlayments; (602) 269-2288 Revision 9: 10/14/2017
Page 2 of 7'
.0
5.3 Fire Classification is not part of this Lai
Directory for fire ratings of this product.
5.4 Boral Roof Underlayments may be used
referenced within FBC approval documen'
Jurisdiction for approval based on this ei
covering.
5.5 Allowable Roof Covers: Table 1 pertains
n,.c,.. +..+I,.-, inctri
5.5.1
5.6
5.6.1
5.6.2
r `
F TRINITY END
oratory Report; refer to current Approved Roofing Materials
h any prepared roof cover where the product is specifically
If not listed, a request may be made to the Authority Having
ation combined with supporting data for the prepared roof
use of each listed underlayment by -itself beneath the stated
nnc and Table 2 for two-Dlv underlayment options.
TABLE
[ 1
1: ROOF COVER OPTIONS "
Asphalt
Adhesive -set
Metal
Wood Shakes
Slate
Underlayment
Shingles
Na
1-On Tile
Tile
& Shingles
Boral_T,ileSea1:5o"�T'
Yes
No',*.No
Yes
Yes.
Yes
P _ ..
BoraT`rleSea "r'
Yes
Yes
Yes
5 5 1)
Yes
Yes
Yes
91r4�
(See
GatorSeal
Yes
No
" No
No
Yes
Yes
I: ..,.:. —A +,, .. of fnlll ,.,ino Annrrn.ad the adhesives / underlavment combinations.
TABLE lA ALLOWABLEITILE
ADHESIVE UNDERLAYMENT COMBINATIONS
Adhesive
Florida Product Approval
Underlayments
DAP Foam Touch'n Seal Storm Bond Roof Tile
dhesive
FL14506
Boral TileSeal"T
Dow TILE BONDT" Roof Tile Adhesive
FL22525
Boral TileSeal"r
ICP Adhesives Polyset® AH-160
FL6332
Boral TileSeal"T
1CP7Cd(iesives Polys RTA 1 :;
FL6276Boral'TifeSeal"r
Allowable Substrates: -
Direct -Bond to Deck:
Citadel Plus, Boral TileSeal 50"T, Boral 1
➢ Plywood (unprimed or primed wit[
Boral TileSeal"T:
➢ OSB primed with ASTM D41 prime
Note: Refer to Section 5.6.4 for uplift li
where the overlying roof cover is adhesiv
Bond to Base Layer Underlayment:
Citadel Plus, Boral TileSeal 5011T, Boral
➢ ASTM D226, Type II felt; Citadel F
For installations under mechanically att
minimum codified requirements. For i
attached per minimum requirements of
Section 5.6.4 herein, or as tested in accc
' Refer to Tile Manufacturers or Adhesive Manufacturer's
IeSeal"T or GatorSeal:
ASTM D41 primer).
`ions associated with direct -deck underlayment installations
tile -roofing
eSeal"T or GatorSeal:
d prepared roof coverings, base layer shall be attached per
lations under adhesive -set tile systems, base layer shall be
1/TRI April 2012 (04-12), Appendix A, Table 1, or as listed in
ce with FBC 1504.3.1.
Product Approval for Overturning Moment Resistance Performance.
Evaluation Report M35710.12.10-119
Exterior Research and Design, LLC.
6n' EDITION 2017 FB� NON-HVHZ EVALUATION FL/14/2017
Certificate of Authorization p9503 ( ) Revision 9:10/14/2017
Boral Roof Underlayments; (602) 269-2288
Page 3 of 7
t
TRINITY ER®
5.6.3 Bond to Other Substrate Types:
Citadel Plus, Boral TileSeal 50"T, Boral TileSeal"T or GatorSeal:
➢ ASTM D41 primed metal (e.g., flashing metal, valley metal, etc).
Boral TileSeal"T:
➢ Huber Zip Deck (unprimed or primed with ASTM D41 primer); Dens Deck Prime.
Note: For installation under mechanically attached prepared roof coverings, insulation shall be attached
per minimum requirements of the prepared roof covering manufacturer's Product Approval.
5.6.4 Wind Resistance for Underlavment Systems in Adhesive -set Tile Applications:. FRSA/TRI April 2012 (04-12)
does not address wind uplift resistance of all underlayment systems beneath -adhesive -set tile systems,
where the underlayment forms part of the load -path. The following wind uplift limitations apply to
underlayment systems that are not addressed in FRSA/TRI -.April 2012 (04-12) and are used in adhesive -set
tile applications. Maximum Design Pressure is the result of testing for wind load resistance based on
allowable wind loads, and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety
per FBC 1504.9 has already been applied). Refer to FRSA/TRI April 2012 (04-12), Appendix A, Table 1A or
FBC 1609 for determination of design wind loads
#1 Maximum Design Pressure = -105 psf:
Deck:
Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority
Having Jurisdiction.
Base Ply:
(Optional) Citadel Plus, self -adhered
Underlayment:
Boral TileSeal"T, self -adhered and back -nailed within the selvedge -edge side laps using
12 ga. x 1%" ring shank nails through 32 ga., 1-5/8" diameter tin caps spaced 12-inch o.c.
#2 Maximum Design Pressure = -120.0 psf:
Deck:
Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority
Having Jurisdiction.
Primer:
ASTM D41 to the plywood deck
Base Ply:
Citadel Plus, self -adhered
Cap Sheet:
Boral TileSeal" , self -adhered, and back -nailed within the selvedge -edge side laps using
12 ga. x 1%" ring shank nails through 32 ga., 1-5/8" diameter tin caps spaced 12-inch o.c.
#3 Maximum Design Pressure = -202.5 psf:
Deck:
Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority
Having Jurisdiction.
Primer:
ASTM D41 to the plywood deck
Base Ply:
None
Cap Sheet:
Boral TileSeal"T, self -adhered, and back -nailed within the selvedge -edge side laps using
12 ga. x 1%" ring shank nails through 32 ga, 1-5/8" diameter tin caps spaced 12-inch o.c.
#4 Maximum Design Pressure = -120.0 psf:
Deck:
Min. 2,500 psi structural concrete to meet project requirements to satisfaction of
Authority Having Jurisdiction.
Primer:
ASTM D41 to the concrete deck
Base Ply:
(Optional) Citadel Plus, self -adhered
Cap Sheet:
Boral TileSeal"T, self -adhered
5.6.4.1 Note: For adhesive -set tile systems, if there is a base ply or mid -ply of Citadel Plus in the system, the
project design pressure requirements may not exceed -120 psf.
Exterior Research and Design, I.I.C. Evaluation Report M35710.12.10-R9
Certificate ojAuthorization #9503 6" EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-R8
Boral Roof Underlayments; (602) 269-2288 Revision 9:10/14/2017
Page 4 of 7
y
5.7 Exposure Limitations:
GatorSeal shall not be left exposed for
roof cover.
Boral TileSeal 50HT and Boral TileSez
installation, prior to placement of final ri
Citadel Plus, for use as a base -layer in a
than 180-days after installation, prior to
5.8 Tile Slippage Limitations fFRSA/TRI Apr
When loading roof tiles on the underlay
be as follows. These slope limitations
r'
i
£`E 1�RINITY _ ER®
than 30-days after installation; prior to placement of final
shall not be left exposed, for longer than 180-days after
cover.
-ply underlayment system, shall not be left exposed for longer
cement of subsequent underlayment layer.'
it in direct -deck tile assemblies, the maximum roof slope shall
only be exceeded by using battens during loading of the roof
TABLE 2. TILESLIPPAGE LIMITATIONS
FOR DIRECT -DECK TILE INSTALLATIONS
UnderlaymentT)Ie,Pro
Ilea ,,;,
Stagging Method
Maximum Slope
e Fiat
Max. 10-tile stack
6:12
Boral TileSeal"'
Lugged
Max. 10-tile stack
6:12
6. INSTALLATION:
6.1 Boral Roof Underlayments shall be ins
instructions subject to the Limitations set
6.2 Re -fasten any loose decking panels, and
to remove any dust and debris prior to ar
6.3 Install self -adhering underlayment when
ailed in accordance with Boral Roofing published installation
'brth in Section 5 herein and the specifics noted below.
heck for protruding nail heads. Sweep the substrate thoroughly
llication, and prime the substrate (if applicable).
mbient and surface temperatures are minimum 40'F and rising.
6 4 Citadel Plus:`
6.4.1 Citadel Plus is limited to use as a base or mid -layer in multi -ply underlayment systems beneath Boral
TileSeal 50"T, Boral TileSeal HT or 'GatorSe 1.
6.4.2 ' Slope limitations are those associated with the top -layer underlayment.
6.4.3 Direct to Deck:
Cut the membrane into manageable lent
edge, extending over by %-inch. Fold the
sheet. Place the membrane with the exp
Roll into place with a weighted roller.
Boral recommends fastening of the top E
1-inch diameter plastic or steel cap nai
slopes 7:12 and greater. Overlap succe:
end (vertical) laps.
Install final underlayment layer atop Cil
Boral TileSeal"T or GatorSeal.
6.4.4 To Base Sheet:
Install base sheet of ASTM D226, Type I
Citadel Plus in accordance with Boral I
when used as part of a multi -ply system.
Install optional Citadel Plus as a mi
instructions and Section 6.4.3.
Install final underlayment layer atop' Ci
Boral TileSeal"T or GatorSeal.'
:hs, typically 10 to 12 ft. Align the membrane parallel to the roof
membrane away from the edge onto itself. Remove the release
ised rubberized asphalt onto the deck, pressing firmly into place.
ge of the sheet to the deck with roofing nails, nails & tin -tags or
spaced 24-inch o.c. for slopes below 7:12 and 12-inch o.c. for
ve courses minimum 2 inches (horizontal lap) and minimum 4"
Plus per 'direct -to -deck' instructions for Boral TileSeal 50"T,
felt in accordance with Code requirements or install base ply of
)ofing published installation instructions and Section 6.4.3 and
in accordance with Boral Roofing published installation
Plus per 'direct -to -deck' instructions for Boral TileSeal 50"T,
Exterior Research and Design, U.C. Evaluation Report M35710.12.10-R9.
CertfJicate ofAuthorization g9503 6'" EDITION (2017) FB NON-HVHZ EVALUATION FL14317-R8
Boral Roof Underlal ments; 1602) 269-2288 Revision 9: 30/14/2017
Page S of 7
1 �' EFL®
���
Note: For adhesive -set tile systems, if there is a base ply or mid -ply of Citadel Plus in the system, the
project design pressure requirements may not exceed -120 psf.
6.5 Boral TileSeal.50"rs =
6.5.1 Shall be installed in compliance with the requirements for ASTM D1970 underlayment in FBC Table
1507.1.1 for the type of prepared roof covering to be installed.
6.5.2 Do not use Boral TileSeal 50"T on roof pitches less than 2:12.
6.5.3 Non -Tile Applications, Direct to Deck:
Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof
edge, extending over by %-inch. Fold the membrane away from the edge onto itself. Remove the release
sheet. Place the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place.
Roll into place with a weighted roller.
Boral recommends fastening of the black selvedge edge to the deck with roofing nails, nails & tin -tags or 1-
inch diameter plastic or steel cap nails spaced 24-inch o.c. for slopes below 7:12 and 12-inch o.c. for slopes
7:12 and greater. Overlap successive courses the width of the black -selvedge area, minimum 3-inch.
Seal under end (vertical) laps using approved mastic,' or use Joined"and Folded Seam or Inverted Sheet
Seam method detailed in Boral Roofing published installation instructions.
6.5.4 Non -Tile Applications, to Base Sheet:
Install ASTM D226, Type II felt in accordance with Code requirements or install Citadel Plus in accordance
-with Boral Roofing published installation instructions and Section 6.4. .
Install Boral TileSeal 50" . in. accordance over ASTM D226, Type II felt or Citadel Plus with Boral Roofing
published installation, instructions and Section 6.5.3, except end (vertical) laps, described below.
Apply SBS Mastic under all end (vertical) laps or any other laps where the self -adhering bituminous
underside is in contact with the fabric top surface, rolling the interface into place with a weighted roller.
6.6GatorSeal
__.- -.
6.6.1 Shall be installed in compliance with the requirements for ASTM D1970 underlayment in FBC Table
1507.1.1 for the type of prepared roof covering to be installed.
6.6.2 Do not use GatorSeal on roof pitches less than 2:12.
6.6.3 Non -Tile applications, Direct to Deck:
Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof
edge, extending over by %-inch. Fold the membrane away from the edge onto itself. Remove the release
sheet. Place the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place.
Roll into place with a weighted roller.
Boral recommends fastening of the black selvedge edge to the deck with roofing nails, nails & tin -tags or 1-
inch diameter plastic or steel cap nails spaced 24-inch o.c. for slopes below 7:12 and 12-inch o.c. for slopes
7:12 and greater. Overlap successive courses the width of the black -selvedge area, minimum 3-inch.
Seal end (vertical) laps using SBS Mastic under all side (vertical) laps or any other laps where the self -
adhering bituminous underside is in contact with the granular or mineral top surface, rolling the interface
into place with a weighted roller, or using the Inverted Sheet Seam detailed 'in Boral Roofing published
installation instructions.
6.6.4 Non -Tile Applications, to Base Sheet:
Install ASTM D226, Type II felt in accordance with Code requirements or install Citadel Plus in accordance
with Boral Roofing published installation instructions and Section 6.4.
Install GatorSeal over ASTM D226, Type II felt or Citadel Plus.in accordance with Boral Roofing published
installation instructions and Section 6.6.3 except end (vertical) laps, described below.
Apply SBS Mastic under all side (vertical) laps or any other laps where the self -adhering bituminous
underside is in contact with the granular top surface, rolling the interface into place with a weighted roller.
Exterior Research and Design, LLC. Evaluation Report M35710.12.10-R9
Certificate of Authorization #9503 6" EDITION (2017) FBC NON-HVHZ EVALUATION FL14327-R8
Boral Roof Underlayments, (602) 269-2288 Revision 9:10/14/2017
Page 6 of 7
r
6.7 -Boral TileSeal AT
6.7.1 Shall be installed in compliance with the requirements for ASTM D1970 underlayment in FBC Table
1507.1.1 for the type of prepared roof covering to be installed.
6.7.2 Do not use Boral TileSeal HT on roof pitchless than 2:12.
6.7.3 Non -Tile Applications, Direct to Deck:
For OSB substrate, prime with ASTM D41 primer and allow to dry prior to installation. Cut the membrane
into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge, extending
over by %-inch. Fold the membrane awa from the edge onto itself. Remove the release sheet. Place the
membrane with the exposed rubberized �sphalt onto the deck, pressing firmly into place. Roll into place
with a weighted roller.
Boral recommends fastening of the black elvedge edge to the deck with roofing nails, nails & tin -tags or 1-
inch diameter plastic or steel cap nails sp�ced 24-inch o.c. for slopes below 7:12 and 12-inch o.c. for slopes
7:12 and greater. Overlap successive courses the width of the black -selvedge area, minimum 3-inch.
Seal under end (vertical) laps using approved mastic, or use Joined and Folded Seam or Inverted Sheet
Seam method detailed in Boral Roofing p blished installation instructions.
6.7.4 Non -Tile Applications, to Base Sheet:
Install ASTM D226, Type II felt in accordance with Code requirements or install Citadel Plus in accordance
with Boral Roofing published installation instructions and Section 6.4.
Install Boral TileSeal HT over ASTM D226, Type II felt or Citadel Plus in accordance with Boral Roofing
published installation instructions and Section 6.7.3, except end (vertical) laps, described below.
Apply SBS Mastic under all end (verticTI) laps or any other laps where the self -adhering bituminous
underside is in contact with the fabric top surface, rolling the interface into place with a weighted roller.
6.7.5 Tile Applications:
Reference is made to FRSA/TRI April 21 (04-12) Installation Manual and Table 1 herein, using the
instructions noted above as a guideline.
For mechanically fastened tile roofing o er 2-ply system, consisting of Base Sheet and self -adhering top
sheet(s), Base Sheet fastening shall be not less than FRSA/TRI April 2012 (04-12), Table 1.
For adhesive -set tile applications, refer to Section 5.6.4 herein.
Note: For adhesive -set tile systems, if there is a base ply or mid -ply of Citadel Plus in the system, the
project design pressure requirements ma,I not exceed -120 psf.
Refer to Section 5.8 for tile staging limit tions. Battens must be used for all tile installations atop Boral
TileSeal HT with roof pitches of 2%: to le s than 3:12.. Boral Roofing's Elevated Batten System or counter
battens are required.
7. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority HMI
this product.
8. MANUFACTURING PLANTS:
Brentwood, NH
9. QUALITY ASSURANCE ENTITY:
UL, LLC. — QUA9625; (631) 546-2458;
- END OF
Jurisdiction in order to properly evaluate the installation of
TION REPORT -
Exterior Research and Design, LLC. Evaluation Report M35710.12.10-R9
Certificate of Authorization #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-RB
Boral Roof Underlaylnents; (602) 269-2288 Revision 9:10/14/2017
Page 7 of 7