HomeMy WebLinkAboutNOA RIDGE VENT_ M1AMI-MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) Miami, Florida 33175-2474
BOARD AND CODE ADMINISTRATION DMSION I T (786) 315-2590 F (786) 315-2599
NOTICE 'OF ACCEPTANCE (NOA) www.miamiaaae.sov/economy
CertainTeed Corporation
20 Moores Road
Malvern, PA 19355
SCOPE: I.
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER -Product Control Section to be
used in Miami Dade -County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This NOA shall not be valid after the expir,
(in Miami -Dade County) and/or the AHJ (
product or material tested for quality assurE
manner, the manufacturer will incur the ex
suspend the use of such product or material
if it is determined by Miami -Dade County
requirements of the applicable building code
n date stated below. The Miami -Dade County Product Control Section
areas other than Miami -Dade County) reserve the right to have this
purposes. If this product or material fails to perform in the accepted
ise of such testing and the AHJ may immediately revoke, modify, or
hin their jurisdiction. RER reserves the right to revoke this acceptance,
oduct Control Section that this product or material fails to meet the
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone 'of the Florida Building Code.
DESCRIPTION
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposeg shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety. i
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the j ob site at the request of the Building Official.
This NOA consists of pages 1 through 4
The submitted documentation was reviewed by Gaspar J Rodriguez.
MIAMI•DADE COUNTY
..•Ou) . I
i
i
NOA No. 5-0831.06
Expiration Date: 09/23/19
Approval Date: 06/02/16
File COPY page 1 of 4
ROOFING COMPONENT APPROVAL
Category: Roofing
Sub -Category: Ventilation
Material: Plastic
Minimum Slope: 3:12
TRADE NAMES OF PRODUCTS
Product Dimensions
Co.ertainTeed-Ridge Length:48"
nt-12�;lt+ered Width: 13.8"
Height: Ys"
MANUFACTURING LOCATION
1. Orrick, MO
EVIDENCE SUBMITTED
Test ALYency
Architectural Testing
Hurricane Engineering & Testing,
Inc.
PRI Construction Materials
Technologies
Y
ACTURED OR LABELED BY APPLICANT
Test Product
Specifications Description
TAS 100(A) Polypropylene plastic low profile ridge vent with an
integral end plug for installation in asphaltic shingle
roof systems.
6545 .01-109-18
D8316.01-801-18
D8316.02-801-18
F400
T102
A001
AVIG-010-02-01
AVIG-010-02-02
Test Name/Report
Date
TAS 100
07/26/06
TAS 100 (A)
09/16/14
TAS 100 (A) Calibration
12/02/14
ASTM D 1929
07/01/09
ASTM D 638
01/30/09
ASTM G 155
09/13/02
ASTM D 635
12/02/14
ASTM D 1929
12/02/14
ASTM D 2843
12/02/14
ASTM G 155
06/09/15
NOA No.: 15-0831.06 ,
Expiration Date: 09/23/19
Approval Date: 06/02/16
Page 2 of 4
APPROVED APPLICATION
Trade name: CertainTeed Ri
System Type A: Mechanical a
Cutout: Cut a 1 Y? slot
slot shall termii
Installation: Center,tIe::vent
Vent -12" Unfiltered
ig the apex of the roof by cutting W on each side of the ridge. The
approximately 6" from each rake edge.
Install pre -manufactured or field cut ridge shingles over the ridge vent in compliance
with the shingle manufacturer's current approved Notice of Acceptance, and the shingle _
and ridge vent's installation instructions. Nails shall be of sufficient length to penetrate
through the sheathing a minimum YI6".
Ventilation Calculations: Refer to
Minimum Slope: 3:12
LIMITATIONS:
1. Refer to applicable building codes for
2. CertainTeed Ridge Vent shall not be i
3. All products listed herein shall have at
Rule 61 G20-3 of the Florida Adminis
4. All plastic ridge vent manufacturers
approved listing agency. Follow-up
Office upon request.
5. All approved products listed herein
manufacturer's name or logo, city ar
County Product Control Approved"
MIAMI•DADE COUNTY
i
I
I
s published literature
ventilation.
on roof mean heights greater than 33 feet.
quality assurance audit in accordance with the Florida Building Code and
rative Code.
11 have an unannounced follow-up quality control program from an
results shall be made available to the Miami -Dade Product Control
all be labeled and shall bear the imprint or identifiable marking of the
state of manufacturing facility, and following statement: "Miami -Dade
the Miami -Dade County Product Control Seal as shown below.
NOA No.: 15-0831.06
Expiration Date: 09/23/19
Approval Date: 06/02/16
Page 3 of 4
n
I
I
I
END OF THIS ACCEPTANCE
i
I
NOA No.: 15-0831.06
Expiration Date: 09/23/19
Approval Date: 06/02/16
Page 4 of 4