HomeMy WebLinkAboutINSTALLATION-OPERATION INSTRUCTIONU
0 . YG 03
INSTALLATION/OIPERATION INSTRUCTIONS
Congratulation on purchasing the YARDGARD safety alarm. The YARDGARD can
be used to monitor potential dangerous areas, and provides a loud volume
alarm/alert when these areas are entered. It can be used indoors or outdoors,
mounted on a wooden fence or metal gate. It can be mounted on any doorway or
opening that leads,to potentially dangerous areas.
CAUTION: The alarm siren is very loud. Never place the unit close to your ear.
Prolonged exposure to the loud siren can affect your hearing. Install the unit at
minimum height 54"1 high enough to be out of reach of children.
This YARDGARD is an entry monitor device. All safety precautions should be
maintained, including parental supervision.
Neither SmartPool LLC. nor anyone else who has been involved in the creation,
reproduction or delivery shall bei liable for any direct, indirect, consequential or
incidental damages arising out of the use of the YARDGARD.
I
I
YG03MAN-REV 01.17-DATE 9/2017
Installing the Battery
Before installing the battery, use a
hold the magnet sensors together
dot matched to dot, thereby prever
from sounding after the battery is i
mounting the unit.
To install the battery, remove the f
back, then open the battery door.
Install a fresh 9V battery (not inch
battery compartment. Check the p
Close the battery door and tighten
Now the unit is ON and in workin
battery is installed properly, pres
button located at the lower right
beep when you press this button
heard, check the battery installat
with a new battery.
fibber band to
imporarily, with
ing the alarm
stalled when
ur screws at the
tided) into the
polarity.
the four screws.
g mode. To check if
s the battery check
corner. The unit will
i If no beep sound is
on again, or replace
Auto Battery Check I
The unit will keep monitoring the battery level. When
it detects that the battery is low, you will hear a loud
and short beep every minute. Change battery when
you hear this beep. I
YG03MAN-REV 01.17-DATE 9/2017
i
i
Mounting on a Wooden rence
install the mounting bracket onto a
fence post using the two bigger
screws. Slide the alarm unit onto this
mounting bracket. You will feel a click
when the unit is properly installed.
Mount the two magnet sensors on
the fence post, one on each side,
using the four smaller screws.
Mounting on a Metal Gate
Install the mounting bracket onto
gate post using two nylon straps.
Slide the alarm unit onto this
mounting bracket. You will feel a
when the unit is properly installec
lick
Mount the two magnet sensors onto
the two spacer stands using the four
smaller screws and then mount this
sensor assembly onto the gate post
using the nylon straps. j
i
i
YG03MAN-REV 01.17-DATE 9/2017
i
Mounting on a Wall An 6-Wass Doors
Install the mounting bracket using t� wo pieces of
double sided foam tape. Slide the alarm unit onto
this mounting bracket. You will feel a click when the
unit is properly installed.
Apply the double sided foam tape
recessed area of magnet sensor p
magnet sensors, one on the door
the door frame.
Mount the magnet sensor with th
stationary surface such as door f
Additional PASS/RESET Switch
This unit provides an additional R
switch, which can be mounted on
the door for convenient access frc
This additional switch can be moi
smaller screws or double -sided fc
nto the bottom
ir. Mount the
nd the other on
wire onto the
me.
►SS/ RESET
the other side of
m both sides.
nted by the 2
am.
YG031VIN-REV 01.17-DATE 9/2017
I
Operation
This YARDGARD is designed to monitor the opening
of gate or door, to alert an adult if a child has opened
a gate or door to a potential dangerous area.
Check the battery. Press the CHECK button should
give a loud beep, otherwise replace with a new
battery. The unit will give a loud si en if gate or door
is opened by more than one inch.
For adult entry, press the PASS button. The unit will
allow the door be opened up to 7 seconds without
triggering alarm. However, if the giate or door is
opened for over 7 seconds, the alarm will trigger.
To reset the alarm, first close the door and then
press the PASS/RESET button. The alarm is now
back to stand by mode.
To exit the protected area, press the PASS/RESET
button and exit the area within 301 seconds.
Automatic Reset Under All Conditions
The unit will be reset automatically in 30 seconds
after the last key activation. If thel PASS/RESET
button is pressed but the adult entry 7 seconds
allowance is not utilized, this adult entry allowance
will be canceled in 30 seconds, and reset to standby
mode automatically.
I
YG03M�N-REV 01.17-DATE 9/2017
Auto Siren OFF
Siren can be turned OFF manually as describe on
previous section, or the unit will reset in 4 minutes
automatically if the gate is closed.
Automatic Continuous Monitoring
If alarm is triggered and reset by itself in 4 minutes,
the unit will check the condition of Imagnet contact
sensor to decide if the door remai s open or not. If
the door is left open, the alarm so nds again for 4
p g
minutes, check the door condition lagain and
continue the cycle until the door isl closed.
MPORTANT
Keep the distance between the two magnet sensor contacts to
a maximum of 3/4"
Test the unit by opening the door. The alarm should go off immediately;
otherwise contact SmartPoo at (732) 730-9880.
Do not rely on the alarm until the test results are satisfactory.
YG03 I AN -REV 01.17-DATE 9/2017
www.smartpoolxom
YG03iAN-REV 01.17-DATE 9/2017