Loading...
HomeMy WebLinkAboutEVALUATION REPORT'SBy �3 Q Wde County \J,T RINI .ERD EVALUATION REPORT Boral Roofing 7575 Irvine Center Drive, JSuite Irvine, CA. 92618 (602)269-2288 CANNED BY ST. LUCIE COUNTY BUI NG DIVISION REVIEWED FOR CON E REVIEWED BY. EXTERIOR RESEARCH & DESIGN, LLC. DATE < Certificate of Authorization #9503 PLANS AND ERMIT M T E KEPT ON 70B 353 CHRISTIAN STREET, UNIT#13 SITE OR NO INSPECTIONS) WILL BE MADE OXFORD, CT 06478 RECEIVED (203) 262-9245 0 MAY 2i?.018 ST. Lucie County, Permitting Evaluation Report M35710.12.10-R9 FL14317-R8 Date of Issuance:12/21/2010 Revision 9:10/14/2017 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code sections noted herein. DESCRIPTION: Boral Roof Underlayments LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. Trinity) ERD requires a complete review of this Evaluation Report relative to updated Code IIrequirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1,through 7. Prepared by: I Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCAANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 10/14/2017. This does not serve as an electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. TrinityJERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinity l ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither Trinityl ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. i'ESE PLANS AND ALL PROPOSED WORT( IRE SUBJECT TO ANY CORRECTIONS CI?f�CE 1r> p rA$,TIMMS OR ATTACHMENTS � EQUIRED BY FIELD fNSPECTORS THAT AN 11P,+ ���R�N�I�(LIl`Y OF THE �� �' , � ,fAY BE NECESSARY IN ORDER TO Y. OMPLY WITH ALL APPLICABLE CODES. C01R IMI OF RECORD, ;Q,o TRINITY ERD ROOFING COMPONENT EVALUATION: i 1. SCOPE: Product Category: Roofing I Sub -Category: Underlayment Compliance Statement: Boral Roof Underlayments, as marketed by Boral Roofing, have demonstrated compliance with the following sections of the 6th Edition (2017) Florida Building Code through testing in accordance with the following Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: Section Pro a Standard Year 1504.3.1 Wind Uplift UL 1897 2012 1507.1.1, T1507.1.1, 1507.2.9.2 Physical;Properties ASTM D1970 2015 1507.3.3 Physical Properties FRSA/TRI April 2012 (04-12) 2012 3. REFERENCES: Entity Examination Reference Date ERD (TST 6049) Physical Properties M36790.07.11 09/30/2011 ERD (TST 6049) Physical Properties B40380.08.12 08/28/2012 ERD (TST 6049) Tensile Adhesion / LTA C41420.09.12-2 09/11/2012 ERD (TST 6049) Adhesion B41940.09.12 09/13/2012 ERD (TST 6049) Tensile Adhesion / LTA B47390.07.14-1 07/31/2014 ERD (TST 6049) Tensile Adhesion / LTA B47390.09.14 09/04/2014 PRI (TST 5878) ASTMI D1970 NEI-031-02-02:REV 10/27/2010 PRI (TST 5878) ASTM D1970 NEI-029-02-01:REV 12/03/2010 PRI (TST 5878) Tensile Adhesion / LTA NEI-046-02-01REV 12/17/2010 PRI (TST 5878) FRSA�TRI April 2012 NEI-076-02-01 02/14/2011 PRI (TST 5878) ASTM D1970 NEI-034-02-02 01/29/2013 PRI (TST 5878) Wind Uplift BORR-001-02-01 03/17/2015 PRI (TST 5878) Wind Uplift BORR-005-02-01 06/24/2015 UL, I.I.C. (QUA 9625) Quality Assurance Service Confirmation Exp. 08/21/2020 4. PRODUCT DESCRIPTION: 4.1 Self -Adhering Underlayments: 4.1.1 Boral TileS 1® 50"T is a nominal 50-mil thick, polyester -surfaced, self -adhering SBS modified bitumen roof and ayment; m is ASTM D1970. 4.1.2 ral TileSeal® "T is nominal 60-mil thick, polyester -surfaced, self -adhering SBS modified bitumen roof n era ;meets ASTM D1970 and FRSA/TRI 04-12. 4.1.3 GatorSeal® is a nominal 55-mil thick, granular -surfaced, fiberglass reinforced, self -adhering SBS modified bitumen roof underlayment; meets ASTM D1970. 4.1.4 Citadel® Plus is a nominal 48-mil thick, fabric -surfaced, fiberglass reinforced, self -adhering SBS modified bitumen roofing underlayment for use as a base -layer in two-ply underlayment systems; meets ASTM D1970. S. LIMITATIONS: 5.1 This is a building code evaluation. Neither TrinityJERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions. Exterior Research and Design, I.I.C. Evaluation Report M35710.12.10-R9 Certificate afAuthari:ation #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-118 Boral Roof Underlayments; (602) 269-2288 Revision 9:10/14/2017 Page 2 of 7 `J TRINITY ERD 5.3 Fire Classification is not part of this Laboratory Report; refer to current Approved Roofing Materials Directory for fire ratings of this product. 5.4 Boral Roof Underlayments may be used with any prepared roof cover where the product is specifically referenced within FBC approval documents. If not listed, a request may be made to the Authority Having Jurisdiction for approval based on this evaluation combined with supporting data for the prepared roof covering. 5.5 Allowable Roof Covers: Table 1 ipertains to use of each listed underlayment by -itself beneath the stated roof covers. Refer to the installation instructions and Table 2 for two-ply underlayment options. TABLE ROOF COVER,OPTIONS: „ . „ i Asphalt Adhesive -set Wood Shakes Underlayment Nail -On Tile Metal Slate Shingle's Tile & Shingles Boral TileSeal 50"�>Yes ', ttor aNas Yes 3 Yes Yes , BoralTileSeal"T yes Yes `Yes eL Yes Yes Yes GatorSeal Yes[ � xNq �xr,>. �r.,� , NNa M.. o, Yes Yes 5.5.1 "Adhesive -set Tile" is limited to use of following Approved tile adhesives / underlayment combinations. TABLE 1A Au OVJABLE TILE ADklESIVE J UNI7ERE1lYMENT COMBINATIONS- �.. ... W ,.. Adhesive Florida Product Approval Underlayments DAP Foam Touch'n Seal StormBohd Roof Tile Adhesive FL14506 Boral TileSeal"T Dow TILE BOND" Roof Tile Adhesive FL22525 Boral TileSeal"T ICP Adhesives Polyset® AH-160 i FL6332 Boral TileSeal"T ICP Adhesives Polyset° RTA-1 FL6276 Boral TileSeal"T 5.6 Allowable Substrates: 5.6.1 Direct -Bond to Deck: i Citadel Plus, Boral Tile5eal;50"T, Boral TileSeal"T or GatorSeal: ➢ Plywood (unprimed or primed with ASTM D41 primer). Boral TileSeal"T: ➢ OSB primed with ASTM D41 primer. Note: Refer to Section 5.6.4 for uplift limitations associated with direct -deck underlayment installations where the overlying roof co ver is adhesive -set tile roofing 5.6.2 Bond to Base Laver Underlayment: Citadel Plus, Boral TileSeal 50"T, Boral TileSeal"T or GatorSeal: ➢ ASTM D226, Type II felt; Citadel Plus. For installations under mechanically attached prepared roof coverings, base layer shall be attached per minimum codified requirements. For installations under adhesive -set tile systems, base layer shall be attached per minimum requirements of FRSA/TRI April 2012 (04-12), Appendix A, Table 1, or as listed in Section 5.6.4 herein, or as tested in accordance with FBC 1504.3.1. 1 Refer to Tile Manufacturer's or Adhesive Manufacturer's Florida Product Approval for Overturning Moment Resistance Performance. Exterior Research and Design, I.I.C. Evaluation Report M35710.12.10-R9 Certificate of Authorization #9503 6T" EDITION (2017) FBC NON-HVH2 EVALUATION FL14317-118 Boral Roof Underlayments; (602) 269-2288 Revision 9:10/14/2017 Page 3 of 7 i TRINITY 1 ERD 5.6.3 Bond to Other Substrate Types: Citadel Plus, Boral TileSeal 50HT, Boral TileSeal"T or GatorSeal: ➢ ASTM D41 primed metal (e.g., flashing metal, valley metal, etc). Boral TileSeal"T: ➢ Huber Zip Deck (unprimed or primed with ASTM D41 primer); Dens Deck Prime. Note: For installation under mechanically attached prepared roof coverings, insulation shall be attached per minimum requirements of the prepared roof covering manufacturer's Product Approval. 5.6.4 Wind Resistance for Underlayment Systems in Adhesive -set Tile Applications: FRSA/TRI April 2012 (04-12) does not address wind uplift resistance of all underlayment systems beneath adhesive -set tile systems, where the underlayment formsi part of the load -path. The following wind uplift limitations apply to underlayment systems that are not addressed in FRSA/TRI April 2012 (04-12) and are used in adhesive -set tile applications. Maximum Design Pressure is the result of, testing for wind load resistance based on allowable wind loads, and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has already been applied). Refer to FRSA/TRI April 2012 (04-12), Appendix A, Table 1A or FBC 1609 for determination of design wind loads #1 Maximum Design Pressure = -105 psf: Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction. Base Ply: (Optional) Citadel Plus, self -adhered Underlayment: Boral TileSeal"T, self -adhered and back -nailed within the selvedge -edge side laps using 12 ga. x 1%"firing shank nails through 32 ga., 1-5/8" diameter tin caps spaced 12-inch o.c. #2 Maximum Design Pressure = 420.0 psf: Deck: Min. 15/32i inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction. Primer: ASTM D41 to the plywood deck Base Ply: Citadel Plus, self -adhered Cap Sheet: Boral TileSeal"T, self -adhered, and back -nailed within the selvedge -edge side laps using 12 ga. x 1Y." ring shank nails through 32 ga., 1-5/8" diameter tin caps spaced 12-inch o.c. #3 Maximum Design Pressure = I202.5 psf: Deck: Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority Having Jurisdiction. - Primer: ASTM D41 to the plywood deck Base Ply: None Cap Sheet: Boral Tile Sea l"T, self -adhered, and back -nailed within the selvedge -edge side laps using 12 ga. x 1'%" ring shank nails through 32 ga., 1-5/8" diameter tin caps spaced 12-inch o.c. #4 Maximum Design Pressure .= -120.0 psf: Deck: Min. 2,500 psi structural concrete to meet project requirements to satisfaction of Authority Having Jurisdiction. Primer: ASTM D41 to the concrete deck Base Ply: (Optional) Citadel Plus, self -adhered Cap Sheet: Boral Till eSeal"T, self -adhered 5.6.4.1 Note: For adhesive -set tilee systems, if there is a base ply or mid -ply of Citadel Plus in the system, the project design pressure requirements may not exceed -120 psf. Exterior Research and Design, U.C. Evaluation Report M35710.12.10•R9 Certificate oJAuthorization #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-R8 !Boral Roof Underlayments; (602) 269-2288 Revision 9:10/14/2017 Page 4 of 7 ERD QOTRINITY( 5.7 Exposure Limitations: GatorSeal shall not be left exposed for longer than 30-days after installation, prior to placement of final roof cover. I Boral TileSeal 50"T and Boral TileSeal"T shall not be left exposed for longer than 180-days after installation, prior to placement oflfinal roof cover. Citadel Plus, for use as a base -layer in a two-ply underlayment system, shall not be left exposed for longer than 180-days after installation, prior to placement of subsequent underlayment layer. I 5.8 Tile Slippage Limitations IFRSA/TRI April 2012 (04-12)1: When loading roof tiles on the underlayment in direct -deck tile assemblies, the maximum roof slope shall be as follows. These slope limitations can only be exceeded by using battens during loading of the roof tiles. TABLE 2, TILE`SLIpPAGE LIMITA IONS FORDIRECT-DECK T,ILEA NSTALLATIONS ' Underlayment Tile Profile Stagging Method Maximum Slope HT Boral TileSeal Flat j Max. 10-tile stack 6:12 Lugged Max. 10-tile stack 6:12 6. INSTALLATION: 6.1 Boral Roof Underlayments shall be installed in accordance with Boral Roofing published installation instructions subject to the Limitations set forth in Section 5 herein and the specifics noted below. 6.2 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove any dust and debrisl1prior to application, and prime the substrate (if applicable). 6.3 Install self -adhering underlayment when ambient and surface temperatures are minimum 407 and rising. f 6 4 t Citadel>Pluss n k 6.4.1Citadel Plus is limited to use' as a base or mid -layer in multi -ply underlayment systems beneath Boral TileSeal 50"T, Boral TileSeal HT ;or GatorSeal. 6.4.2 Slope limitations are those asIsociated with the top -layer underlayment. 6.4.3 Direct to Deck: Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge, extending over by %-inch. Fold the membrane away from the edge onto itself. Remove the release sheet. Place the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place. Roll into place with a weighted roller. Boral recommends fastening of the top edge of the sheet to the deck with roofing nails, nails & tin -tags or 1-inch diameter plastic or steel cap nails spaced 24-inch D.C. for slopes below 7:12 and 12-inch D.C. for slopes 7:12 and greater. O,uerlap successive courses minimum 2 inches (horizontal lap) and minimum 4" end (vertical) laps. Install final underlayment Iayer atop Citadel Plus per 'direct -to -deck' instructions for Boral TileSeal 50"T, Boral TileSeal"T or GatorSeal. 6.4.4 To Base Sheet: Install base sheet of ASTIVI D226, Type II felt in accordance with Code requirements or install base ply of Citadel Plus in accordance with Boral Roofing published installation instructions and Section 6.4.3 and when used as part of a multi -ply system. Install optional Citadel Plus as a mid -ply in accordance with Boral Roofing published installation instructions and Section 614.3. Install final underlayment layer atop Citadel Plus per 'direct -to -deck' instructions for Boral TileSeal 50"T, Boral TileSeal"T or GatorSeal. Exterior Research and Design, I.I.C. Evaluation Report M35710.12.10-R9 Certificate ojAuthorization #9503 6T",EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-118 Boral Roof Underlayments; (602) 269-2288 Revision 9: 10/14/2017 Page 5 of 7 TRINITY `ERD Note: For adhesive -set tile systems, if there is a base ply or mid -ply of Citadel Plus in the system, the project design pressure requirements may not exceed -120 psf. 6 6.5.1 Shall be installed in compliance (with the requirements for ASTM D1970 underlayment in FBC Table 1507.1.1 for the type of prepared roof covering to be installed. HT 1 6.5.2 Do not use Boral TileSeal 501 on roof pitches less than 2:12. 6.5.3 Non -Tile Aor lications. Direct to Deck: Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge, extending over by X-inch. Fold the membrane away from the edge onto itself. Remove the release sheet. Place the membrane with,'the exposed rubberized asphalt onto. the deck, pressing firmly into place. Roll into place with a weighted roller. Boral recommends fastening of the black selvedge edge to the deck with roofing nails, nails & tin -tags or 1- inch diameter plastic or ,steel cap nails spaced 24-inch o.c. for slopes below 7:12 and 12-inch o.c. for slopes 7:12 and greater. Overlap successive courses the width of the black -selvedge area, minimum 3-inch. Seal under end (vertical) laps using approved mastic, or use Joined and Folded Seam or Inverted Sheet Seam method detailed in Boral Roofing published installation instructions. 6.5.4 Non -Tile Applications, to Base Sheet: Install ASTM D226, Type II felt in accordance with Code requirements or install Citadel Plus in accordance with Boral Roofing published installation instructions and Section 6.4. Install Boral TileSeal 50"T in accordance over ASTM D226, Type II felt or Citadel Plus with Boral Roofing published installation instructions and Section 6.5.3, except end (vertical) laps, described below. Apply SBS Mastic under all end (vertical) laps or any other laps where the self -adhering bituminous underside is in contact with the fabric top surface, rolling the interface into place with a weighted roller. 6.6.1 Shall be installed in compliance with the requirements for ASTM D1970 underlayment in FBC Table 1507.1.1 for the type of prepared roof covering to be installed. 6.6.2 Do not use GatorSeal on roof,pitches less than 2:12. 6.6.3 Non -Tile applications, Direct to Deck: Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge, extending over by %-inch. Fold the membrane away from the edge onto itself. Remove the release sheet. Place the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place. Roll into place with a weighted roller. Boral recommends fastening of the black selvedge edge to the deck with roofing nails, nails & tin -tags or f- inch diameter plastic or steel cap nails spaced 24-inch o.c. for slopes below 7:12 and 12-inch o.c. for slopes 7:12 and greater. Overlap successive courses the width of the black -selvedge area, minimum 3-inch. Seal end (vertical) laps using SBS Mastic under all side (vertical) laps or any other laps where the self - adhering bituminous underside is in contact with the granular or mineral top surface, rolling the interface into place with a weighted roller, or using the Inverted Sheet Seam detailed in Boral Roofing published installation instructions. 6.6.4 Non -Tile Applications, to Base Sheet: Install ASTM D226, Type Ilifelt in accordance with Code requirements or install Citadel Plus in accordance with Boral Roofing published installation instructions and Section 6.4. Install GatorSeal over ASTM D226, Type II felt or Citadel Plus in accordance with Boral Roofing published installation instructions and Section 6.6.3 except end (vertical) laps, described below. Apply SBS Mastic under all side (vertical) laps or any other laps where the self -adhering bituminous underside is in contact with the granular top surface, rolling the interface into place with a weighted roller. Exterior Research and Design, I.I.C. Evaluation Report M35710.12.10-R9 Certificate of Authorization #9503 C" EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-R8 Boral Roof Underlayments; (602) 269-2288 Revision 9:10/14/2017 Page 6 of 7 QTRINIT'Y'�JERD 6:7 Boral TileSeal , 6.7.1 Shall be installed in compliance vdith the requirements for ASTM D1970 underlayment in FBC Table 1507.1.1 for the type of prepared ri of covering to be installed. 6.7.2 Do not use Boral TileSeal HT on roof pitches less than 2:12. 6.7.3 Non -Tile Applications, Direct to Deck: For OSB substrate, prime with AS M D41 primer and allow to dry prior to installation. Cut the membrane into manageable lengths, typically 10 to 12 ft. Align the membrane parallel to the roof edge, extending over by''/< -inch. Fold the membrane away from the edge onto itself. Remove the release sheet. Place the membrane with the exposed rubberized asphalt onto the deck, pressing firmly into place. Roll into place with a weighted roller. Boral recommends fastening of the black selvedge edge to the deck with roofing nails, nails & tin -tags or f- inch diameter plastic or steel cap nails spaced 24-inch D.C. for slopes below 7:12 and 12-inch D.C. for slopes 7:12 and greater. Overlap successive courses the width of the black -selvedge area, minimum 3-inch. Seal under end (vertical) laps using approved mastic, or use Joined and Folded Seam or Inverted Sheet Seam method detailed in Boral Roofing published installation instructions. 6.7.4 Non -Tile Applications, to Base Sheet: Install ASTM D226, Type II felt in accordance with Code requirements or install Citadel Plus in accordance with Boral Roofing published installation instructions and Section 6.4. Install Boral TileSeal HT over ASTM D226, Type II felt or Citadel Plus in accordance with Boral Roofing published installation instructions and Section 6.7.3, except end (vertical) laps, described below. Apply SBS Mastic under all end (vertical) laps or any other laps where the self -adhering bituminous underside is in contact with theifabric top surface, rolling the interface into place with a weighted roller. 6.7.5 Tile Applications: Reference is made to FRSA/TRI April 2012 (04-12) Installation Manual and Table 1 herein, using the instructions noted above as a guideline. For mechanically fastened tileiroofing over 2-ply system, consisting of Base Sheet and self -adhering top sheet(s), Base Sheet fastening shall be not less than FRSA/TRI April 2012 (04-12), Table 1. i For adhesive -set tile applications, refer to Section 5.6.4 herein. Note: For adhesive -set tile systems, if there is a base ply or mid -ply of Citadel Plus in the system, the project design pressure requirements may not exceed -120 psf. Refer to Section 5.8 for tile staging limitations. Battens must be used for all tile installations atop Boral TileSeal HT with roof pitches of 2%: to less than 3:12. Boral Roofing's Elevated Batten System or counter battens are required. 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 8. MANUFACTURING PLANTS: Brentwood, NH 9. QUALITY ASSURANCE ENTITY: UL, LLC. — QUA9625; (631) 546-2458; Kanchi.Asrawala-Dokania@ul.com - END OF EVALUATION REPORT - Exterior Research and Design, U.C. Evaluation Report M35710.12.10-R9 Certificate ofAathorisation #9503 eH EDITION (2017) FBC NON-HVHZ EVALUATION FL14317-R8 Boral Roof Underlayments; (602) 269-2288 Revision 9: 10/14/2017 Page 7 of 7 SGANI ku i BY RECEIVED MAY 2 2 2018 EXTERIOR RESEARCH & DESIGN, LLC. Certificate of Authorization N9503 Lucie County, Permitting 353 CHRISTIAN STREET, UNIT#13 JE . OXFORD, CT 06478 (203) 262-9245 EVALUATION REPORT Eagle Roofing Products Florida LLC. Evaluation Report E1322.09.06-115 1575 East Country Road 470 FL7473-RB Sumterville, FL 33585 Date of Issuance: 02/24/2009 (800) 400-3245 Revision 5:10/16/2017 SCOPE: This Evaluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products described herein have been evaluated for compliance with the 6th Edition (2017) Florida Building Code (NON-HVHZ) sections noted herein. DESCRIPTION: Eagle Roof Tiles I LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. Trinity) ERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report numberl preceded by the words "Evaluated by Robert Nieminen, P.E." may be displayed in advertising literature. If an g y portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire;Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 5. Prepared by: �t�itgezrz.,, — Robert J.M. Nieminen, P.E. r, Td The facsimile seal appearing was authorized by Hobert Nieminen, Florida Registration No. 59166, Florida DCA ANE1983' S' P.E. on 10/16/2017. This does not serve as an electronically signed V�q\;E document. Signed, sealed hardcoples have been transmitted to the i .t. �-'�l�rrll tlrltr� Prndurt Annrnval adminlcrrarnr anA rn the namn.l �Imnr CERTIFICATION OF INDEPENDENCE: 1. Trinity] ERD does not have, nor does it intend ,to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Trinity] ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. ' ROOFING SYSTEM EVALUATION: 1. SCOPE: Product Category: Roofing Sub -Category: Roofing Tiles Compliance Statement: Eagle Roof Tiles, as produced by Eagle Roofing Products Florida LLC, have demonstrated compliance with the following sections of thle 6th Edition (2017) Florida Building Code (NON-HVHZ) through testing in accordance with the following Standards. (Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein. i 2. STANDARDS: Section Property Standard Year 1507.3.5, R905.3.5 Physical Properties ASTM C1492 2003(2009) 1507.3.7, R905.3.7 Attachment Requirements FRSA/TRI April 2012 (04-12) 2012 1504.2.1.1 Overturning Moment SSTD it 1997 3. REFERENCES: knifty Examination Reference Date ATL(TST 3782) ASTM C1492 RT0310.01-17, 02-17, 03-17 03/15/2017 ATL (TST 3782) ASTM C1492 — Freeze/thaw RT0706.01-17, 02-17, 03-17 09/25/2017 Tile Roof Institute SSTD 11 Membership Letter 11/29/2005 AT[ (QUA 1844) Quality Assurance Inspection Report 06/07/2017 4. PRODUCT DESCRIPTION: 4.1 ASTM C1492;,Type Itl (Low Piofilej d .a ..._., t BELAIR~ a.. �.. Exterior Research and Design, LLC. Certificate of Authorization #9503 i C" EDITION (2017) FBC NON-HVHZ EVALUATION Eagle,Roofing Products Florida LLC.; (800) 400-3245 0 Evaluation Report E1322.09.06-115 FL7473-R8 Revision 5: 10/16/2017 Page 2 of 5 4.2 4.3 S. LIMITATIONS: 5.1 This is a building code evaluati n. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions. 5.3 Fire classification is not part of this evaluation; refer to FBC 1505.2, Exception 2 (for non-combustible deck) or listing by an approved II esting agency for fire rating of this product. 5.4 Underlayment shall be that which holds Florida Product Approval for use with tile roofing systems. The underlayment Product Approval shall specify allowable method(s) of tile installation (mechanical attachment, mortar -set and/or adhesive -set) for use with the specific underlayment. For mortar -set or adhesive -set tile roofing applications, the underlayment Product Approval shall specify attachment methods for the underlaymerit system to resist wind uplift design loads in accordance with Table 1A of FRSA/TRI April 2012 (04-12). 5.5 "Color -Bonded" or "Slurry -Coated" files are limited to use on projects in areas subjected to weathering indices of 50 or less (negligible weathering), as outlined in Figure 1 of ASTM C1492-03(2009)', reproduced below for reference. This limitation does not apply to the "Color -Through" product offering. 5,0; MEATHERiNG REGJONS .: _.. { :NEf 6 L r I 4EA'T HER,It 7'MODERATE WEATRER1:h SEVERE Vi:EATHERiNG°°. 5.6 All products in the roof assembly shall have quality assurance audit in accordance with FAC Rule 611320-3. Exterior Research and Design, I.I.C. 6TH EDITION (2017) FBC NON-HVHZ EVALUATION Evaluation Report E1322.09.06-RS Certificote oJAuthorization #9503 Eagle Roofing Products Florida LLC.; (800) 40D-3245 FL7473-RS Revision 5:10/16/2017 Page 3 of 5 F;- INSTALLATION' 6.1 Eagle Roof Tiles may be mechanically fastened, mortar -set or adhesive -set. Installation shall comply with manufacturer's current published instructions, but not less than the requirements of FBC 1507.3 and the FRSA/TRI Florida High Wind Concrete and Clay Tile Installation Manual. 6.2 Underlayment shall be installed in accordance with FRSA/TRI April 2012 (04-12) or the underlayment manufacturer's current Product Approval. For mortar -set or adhesive -set tile roofing applications, the underlayment current Product Approval shall specify attachment methods for the underlayment system to resist wind uplift design loads in ad cordance with Table 1A of FRSA/TRI April 2012 (04-12). 6.3 Tiled chment: i 6.3 Mechanically Attached Tile: Icordance with Table 3 of FRSA/TRI April 2012 (04-12) to resist the Uplift Moment determined in Table 2A or 2B of FRSA/TRI April 2012 (04-12) or FBC 1609.5.3. 6.3.2 Mortar -Set Tile: Wind load resistance shall be In accordance with Table 2A or 26 of FRSA/TRI April 2012 (04-12) or FBC 1609.5.3 in conjunction with the mortar manufacturer's Product Approval. 6.3.3 Adhesive -Set Tile: Wind load resistance shall be in (accordance with Table 2A or 213 of FRSA/TRI April 2012 (04-12) or FBC 1609.5.3 in conjunction with the, adhesive manufacturer's current Product Approval. Refer to the current version of the referenced Florida! Product Approval for paddy -placement details and performance data. y ' t F IIE`�iD4, iiii FOEtADHE5IUE�$ET TILE SYSTEms ; n Manufacturer Products Florida Product Approval DAP Foam, Inc. i "Touch N'SealStorm Bond" FL14506 "Touch N' Seal Storm Bond 2" FL21374 Dow Chemical "TILE BOND"" FL22525 j ICP Adhesives & Sealants, Inc. "Polyset® AH-160" FL6332 "Polyset® RTA-1" FL6276 6.3.4 Hip and Ridge Tile: Tile shall be installed in accordance with FRSA/TRI April 2012 (04-12). For hip and ridge tile installations atop hip and ridge metal, refer to the hip and ridge metal manufacturer's current Product Approval (e.g., FL5374) or test report in accordance with SSTD 11 for allowable loads to resist those determined in accordance with Table 1A of FRSA/TRI April 2012 (04-12). Exterior Research and Design, I.I.C. e" EDITION (2017) FBC NON-HVHZ EVALUATION Evaluation Report E1322.09.06-115 Certificate ajAuthari:ation a9503 Eagle Roofing Products Florida LLC.; (800) 400-3245 FL7473-RB Revision 5:10/16/2017 Page 4 of 5 i I TRINITY;, ERD 7. LABELING: 7.1 Each unit shall bear the imprint or identifiable marking of the manufacturer's name or logo. Tile lots shall be labeled in accordance with the requirements of the Accredited Quality Assurance Agency noted herein. FL OR/ D.A., EAGLE FL (LOCATED ON UNDERSIDE OF TILE) (LOCATED ON R FROTSIDE OF TILE) 7.2 Tile not tested for freeze -thaw Ishall state clearly that the lot has not been tested for freeze -thaw acceptance on all lot tags or certification. S. BUILDING PERMIT REQUIREMENTS: 1. As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 9. MANUFACTURING PLANTS: Sumterville, FL 10. QUALITY ASSURANCE ENTITY: Architectural Testing, Inc. — QUA1844; (717) 764-7700 - END OF EVALUATION REPORT - i `ASTM C3492-03, Standard Specification for Concrete Roof Tile, © ASTM International Exterior Research and Design,LLC. Certificate of Authorization #9503 i C" EDITION (2017) FBC NON-HVHZ EVALUATION Eagle Roifing Products Florida LLC.; (800) 400-3245 Evaluation Report E1322.09.06-115 FL7473-R8 Revision 5:10/16/2017 Page 5 of 5 MAY 2 2 25.18 ucle County, pePmitting RINITY ERA. EVALUATION REPORT Vol" V EXTERIOR RESEARCH & DESIGN, I.I.C. Certificate of Authorization #9503 353 CHRI�AN STREET, UNIT 13 1 OXFORD, CT 06478 l/ / I�ZN (203) 262-9245 ICP Adhesives and Sealants, Inc. /�,JEvaluation Report 02768.03.06-118 12505 NW 44th Street 1 I \r\` FL6332-R8 Coral Springs, FL 33065 01& Date of Issuance: 08/08/2008 (888) 774-1419 Revision 8:10/12/2017 SCOPE: V- This Evaluation Report is issued under Rule 61620-3 and the applicable rules and regulations governing the use of construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for compliance with the 6th Edition (2017) Florida Building Code sections noted herein. DESCRIPTION: ICP Adhesives Polyset® AH-160 LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein. CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product changes or the referenced Quality Assurance documentation changes. Trinity I ERD requires a complete review of this Evaluation Report relative to updated Code requirements with each Code Cycle. ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety. INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This Evaluation Report consists of pages 1 through 9. Prepared by: Robert J.M. Nieminen, P.E. Florida Registration No. 59166, Florida DCA ANE1983 The facsimile seal appearing was authorized by Robert Nieminen, P.E. on 10/12/2017. This does not serve as an electronically signed document. CERTIFICATION OF INDEPENDENCE: 1. Exterior Research & Design, LLC. d/b/a Trinity I ERD does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or distributing products it evaluates. 2. Exterior Research & Design, LLC. d/b/a Trinity I ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates. 3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for which the evaluation reports are being issued.. 4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the product. 5. This is a building code evaluation. Neither I,rinitvIERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. A I QTRINITY; ERa ROOFING COMPONENT EVALUATION: i 1. SCOPE: j Product Category: Roofing Sub -Category: Roof Tile Adhesives Compliance Statement: ICP Adhesives Polyset® AH-160, as produced by ICP Adhesives and Sealants, Inc., has demonstrated compliance with the 6`h Edition (2017) Florida Building Code through testing in accordance with the Standards set forth herein. Compliance is slubject to the Installation Requirements and Limitations / Conditions of Use set forth herein. 2. STANDARDS: Sections Property I Standard Year 1504.2.1.1 Overturning resistance SSTD it 1997 3. REFERENCES: Entity Examination; Reference Date ERD (TST 6049) Static Uplift—SSTD 11 P39740.02.12 02/20/2012 ERD (TST6049) Static Uplift —SSTD 11 P39740.11.13-R1 01/02/2015 ICC-ES (EVL2396) 2012 IBC Compliance ESR-1709 12/01/2016 Miami -Dade (CER 1592) HVHZ compliance 17-0322.03 04/27/2017 PRI (TST 5878) Static Uplift —SSTD 11 ECM-001-02-01 09/21/2001 PRI (TST 5878) Static Uplift -SSTD 11 PFI-006-02-01 05/09/2005 PRI (TST 5878) Static Uplift —ISSTD 11 PFI-006-02-02 05/09/2005 PRI (TST 5878) Static Uplift -SSTD 11 PFI-007-02-01 10/11/2005 PRI (TST 5878) Static Uplift —SSSTD 11 PFI-008-02-04 02/21/2006 PRI (TST 5878) Static Uplift -SSTD 11 PFI-009-02-03 02/21/2006 PRI (TST 5878) Static Uplift SSTD 11 TGRI-001-02-03 10/30/2006 PRI (TST 5878) Static Uplift SSTD 11 TGRI-001-02-03 10/30/2006 PRI (TST 5878) Static Uplift —SSTD 11 PFPI-010-02-01 12/07/2006 PRI (TST 5878) Static Uplift SSTD 11 PFPI-011-02-01 12/07/2006 PRI (TST 5878) Static Uplift SSTD 11 PFPI-012-02-01 12/07/2006 PRI (TST 5878) Static Uplift I SSTD 11 PFPI-013-02-01 12/07/2006 PRI (TST 5878) Static Uplift I SSTD 11 PFPI-014-02-01 12/07/2006 PRI (TST 5878) Static Uplift SSTD 11 ECM-003-02-01 06/13/2008 PRI (TST 5878) Static Uplift , SSTD 11 ECM-004-02-01 06/13/2008 PRI (TST 5878) Static Uplift SSTD 11 ECM-005-02-01 06/13/2008 PRI (TST 5878) Static Uplift,—SSTD 11 ECM-006-02-01 06/13/2008 PRI (TST 5878) Static Uplift L SSTD 11 ECM-007-02-01 06/13/2008 PRI (TST 5878) Static Uplift SSTD 11 ECM-008-02-01 06/13/2008 UL LLC (QUA 9625) Quality Assurance Service Confirmation Exp. 06/05/2018 4. PRODUCT DESCRIPTION: 4.1 ICP Adhesives Polyset® AH-160 is !a two -component expanding polyurethane roof tile adhesive that is mixed and dispensed from a dispensing system provided by ICP Adhesives and Sealants, Inc. The components are available in refillable tanks or disposable cylinders (ICP Adhesives ProPack® 30 & 100). S. LIMITATIONS: 5.1 This is a building code evaluation. ;Neither Trinity I ERD.nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained specifically for that purpose. 5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions. i Exterior Research and Design, I.I.C. Evaluation Report 02768.03.06-R8 Certificate ofAutharization #9503 C" EDITION (2017) FBC NON-HVHZ EVALUATION FL6332-Rg ICP Adhesives Polyset® AH-160; (888) 774-1419 Revision 8:10/12/2017 Page 2 of 9 TRINITY � ERD 5.3 Fire classification is not part of this evaluation. Refer to a current Roofing Materials Directory for fire ratings of this product and FBC 1505.2. 5.4 ICP Adhesives Polyset® AH-160 can be used with flat, low and high profile tiles or any rigid, discontinuous roof assembly having a current Florida Statewide Product Approval or approved on a local -level by the Authority Having Jurisdiction. 5.5 Minimum underlayment shall be per FRSA/TRI April 2012 (04-12) or having a current Florida Statewide Product Approval or approved on a local -level by the Authority Having Jurisdiction for use with ICP Adhesives Polyset® AH-160. 1 5.6 Field tiles, meeting the limitations of FBC 1609.5.3, using ICP Adhesives Polyset® AH-160 are limited to projects having an Aerodynamic Uplift Moment (M,,), determined in accordance with FBC 1609.5.3 or Tables 2A and 2B of FRSA/TRI April 2012 (04-12), not greater than the following Allowable Overturning Moment values. Refer to Section 10 and 16 Adhesives and Sealants, Inc. published installation instructions for Adhesive Paddy Placement details. t SABLE ��IEf 0 TILE IM ICP Alik"SIVES POLYSETw A 160a B ' id1MAR&INQFSAKEi1'RLItEAO ItEAFURiIUAENE111 Wr( wadoirco fT1NUlyll�PAtlDY�P4ICENlENT , M1i�tGIN�;LIFSAFI:TYALttEADYAPPLtEOFQ87N7'ERDENEMDEhF7:NIQPADDY PL,SCE14tEMr,.`.,•. �-..., �; v,`, . �., >... 1.>. . �' Tile (FBC 1609.5.3) i Adhesive Paddy Placement Allowable Overturning Type Profile Moment (ft-lbf) Independent; Single Paddy, Medium (W-inch, —30 gram) 60 Clay or Flat t Independent; Sin, gle Paddy, Large (2x10-inch, —45 gram) 112 Interdependent; Two Paddy (44-inch on underlayment, 2x4-inch at the overlap) 54 Independent; Single Paddy, Medium (2x7-inch, —30 gram) 39 Clay Low/ Independent; Single Paddy, Large (2x10-inch, —54 gram) 67 te Concrete Medium Interdependent; Two Paddy (44-inch on underlayment, 2x4-inch at tile overlap) 58 Clay High Independent; Single Paddy, Large (WO -inch, —45 gram) 134 Independent; Single Paddy, Medium (2x7-inch, —30 gram) 65 Clay Independent; Single Paddy, Large (WO -inch, —63 gram) 109 High Concrete Interdependent; Two Paddy (4x4-inch on underlayment, 2x4-inch at tile overlap) 40 Clay Barrel 2x10-inch x ^351gram for pans; 2 @ 1x10-inch x —17 gram for cap 147 Concrete Barrel WO -inch x ^35; gram for pans; 2 @ 1x10-inch x —17 gram for cap 107 Cap atop 2x Clay y Independent Continuous Padd p y ('"34 gram/ft) 135 stringer Concrete Cap atop 2x Independent: Continuous Paddy (— 34 gram/ft) 116 stringer atop 2x Interdependent: ClayCap 105 stringer Head: One (1) #10 x 2Y," screw; Overlap: 1 x 6 inch (-10.5 gram) Cap atop 2x Interdependent: Concrete 76 stringer Head: One (1) #10 x 2%" screw; Overlap: 1 x 6 inch (-10.5 gram) 5.6.1 Data in Table 1 relates to installation over a '30/90' underlayment system, as detailed in the FRSA/TRI April 2012 (04-12). Alternate underlayment systems include those having a current Florida Statewide Product Approval and/or approved on a local -level by the Authority Having Jurisdiction specifically for use with ICP Adhesives Polyset® AH-160. 5.6.2 Tile roof systems using tile types or profiles other than those listed above acquiring acceptance for use with ICP Adhesives Polyset® AH-160 shall be tested in accordance with SSTD 11 or Testing Application Standard TAS 101. For the interdependent two -paddy method, an additional 2-to-1 margin above that specified in SSTD 11 or Testing Application Standard TAS 101 shall be applied in determining the 'allowable overturning moment'. Exterior Research and Design, I.I.C. Evaluation Report 02768.03.06-R8 Certificate of Authorization #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION F1.6332-118 ICP Adhesives Polyset° AH-160; (888) 774-1419 Revision 8:10/12/2017 i Page 3 of 9 .."Q .TRINITY. ERa 5.7 Hip and ridge tiles using ICP Adhesives Polyset® AH-160 are limited to projects having hip/ridge design pressure requirements, determined in accordance with Table 1A of FRSA/TRI April 2012 (04-12), not greater than the following values. Refer to ICP Adhesives and Sealants, Inc. published installation instructions for Adhesive Paddy Placement details. �` �'TAB),E � HIP & �ttp4s: TIL€S tx tCPADsty�s PoLY5' � Ak1150 � � � � �� ���� � � " � ��TO�NE4RGTA+OFSAEEiYA R�AO�APL EAFQAINQEPENDEIl►T`{CONfINULN1Sp�1ODY}PIACEMENT�'� }'� � � � Allowable Tile Substrate Attachment Method Design Pressure (psf) Clay 2x PT ridge board I Independent: Continuous Paddy (-34 gram/ft) 116 Concrete 2x PT ridge board I Independent: Continuous Paddy (— 34 gram/ft) 107 Clay 2x PT ridge board Interdependent: Head: One (1) #10 x 2'/=" screw; 90 Overlap: 1 x 6 inch (-10.5 gram) Interdependent: Head: One (1) #10 x 2%" screw; Concrete 2x PT ridge board 56 Overlap: 1 x 6 inch (-10.5 gram) Clay or Hip & Ridge Channel Metal (FL5374): Independent: Continuous Paddy (^34 gram/ft) 169 Concrete galvanized only Clay or Trim Lock'" (FL5374): aluminum Independent: Continuous Paddy (^34 gram/ft) 173 Concrete galvanized, Galvalume I or stainless steel Clay or Trim Lock— Plus (FL5374): aluminum, Independent: Continuous Paddy (^ 34 gram/ft) 178 Concrete galvanized, Galvalume® or stainless steel Clay Top Notch (FL809S) I Independent: Continuous Paddy (^ 32 gram/ft) 125 Concrete I Top Notch (FL8095) Independent: Continuous Paddy (^ 32 gram/ft) 146 6. INSTALLATION: 6.1 ICP Adhesives Polyset® AH-160 and 1the tile roof assembly shall be installed in accordance with FRSA/TRI April 2012 (04-12) and ICP Adhesives and Sealants, Inc. published installation instructions, subject to the limitations outlined in Section 5. 1 6.2 Hip and ridge boards or hip/ridge metal shall be installed in accordance with the FRSA/TRI April 2012 (04-12). Proprietary hip and ridge metal sha 11 be installed in accordance with the manufacturer's Florida Product Approval. 6.3 Installation shall be performed by applicators who hold a valid Qualified Applicator Card presented by ICP Adhesives and Sealants, Inc. 7. BUILDING PERMIT REQUIREMENTS: As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product. 8. MANUFACTURING PLANTS: Tomball, TX 9. QUALITY ASSURANCE ENTITY: UL, LLC. — QUA9625; (847) 664-3623; LeAnna.Gradecki@ul.com Exterior Research and Design, I.I.C. Certificate ofAuthorization #9503 0' EDITION (2017) FBC NON-HVHZ EVALUATION ICP Adhesive) Polyset® AH-160; (888) 774-1419 Evaluation Report 02768.03.06-R8 FL6332-R8 Revision 8:10/12/2017 Page 4 of 9 10. PADDY PLACEMENT DETAILS (FROM ICP ADH 10.1 Independent, Medium Paddy: Nail through plastic cement Paddy (Beneath (when required) Underlayment ° 7i�i 2in. " Batten'soptional ° Eave Course O loin. 2 in./� Nall through plastic cement (when required) -Paddy (Beneath Tile) Underlayment 0 71n. 21n. Battens optional 0 loin. ' 2 in. Eave Closure Eave Course Fascia Flat/Low Profile Tile Medium Profile Tile Nail through plastic ce (when required) Paddy (Beneath Tile) Undedayment I I W o 71n. 2 in. Battens optional o m i Eave Course � Fascia Weephole loin. 2in, Eaveclosure Drip edge High Profile Tile Exterior Research and Design,LLC. Certificate oJAuthorisation #9503 e" EDITION (2017) FBC NON-HVHZ EVALUATION ICP Adhesives Polyset® AH-160; (888) 774-1419 Evaluation Report 02768.03.06-R8 FL6332-R8 Revision 8:10/12/2017 Page 5 of 9 i rinrrt —, D—M, Tan Exterior Research and Design, LLC. Certificate of Authorization #9503 Nall through plastic ce (when required) IUnderlayment � 10 in.x ` 2 in. wide Battens o optional 1� Eave Course I 10 in. 2 in. 'mil0 1 RINI7YERD Nail through plasticcement (when required) Paddy (Beneath Tile) Undedayment 10 in. x 2 in,wide Battens optional 10 in 2 in. Eave Closure Eave Course Fascia High ProfileTile Modium Prnfil a Tila Paddy (BeneathTile) \Weephole Eave closure Drip edge C" EDITION (2017) FBC NON-HVHZ EVALUATION ICP Adhesives Polyset® AH-160; (888) 774-1419 Evaluation Report 02768.03.06-RS FL6332-R8 Revision 8:10/12/2017 Page 6 of 9 10.3 Interdependent, Two Paddy: Flat/Low Profile Tile Exterior Research and Design, U.C. Certificate of Authorization #9503 Nail through plastic cement Single paddy under file (when required) Paddy (between tiles) Battens Paddy (under tile) optlonal Single paddy on topoft(le` ti x4in. ,y. 2 x 4 m. Single paddy on .. underlayment ,w 10 in. 2 in. Eave closure Eave Course Fascia Medium ProfileTile Nail through plastic ce Single paddy under tile (when required) `t Paddy (between tiles) i Battens e ,,*�,, 1 ,! , Paddy (under tile) Won unaenaymont I'4 x 4 in. Single 2x4i,. paddy on top of tle i � ti Eave Course Fascia Weephole 10 in. �2 in. Eave closure �. Drip edge (High Profile Tile I i 6T" EDITION (2017) FBC NON-HVHZ EVALUATION ICP Adhesives Polyset® AH-160; (888) 774-1419 Evaluation Report 02768.03.06-RS FL6332-R8 Revision 8:10/12/2017 Page 7 of 9 I � I �INIIYRD 10.4 7'hao;PieceBarrei tfigfiPwiile7'il�, 10.5 Hip and Ridge (independent placement): A tread OMP Palys_#AA-160 may be 2"H6d aboty w Feld To al ?ch feVridte Eta, a beadofIC4'Potysel*At4.160 may & surfacean both sides of the Wridge board or gahirked tw applied down the center of Dhe hpnh*r hoard or gat kk., l mew fraae to pavide weaifx M-kySg. tame_ Exterior Research and Design,LLC. Evaluation Report 02768.03.06-R8 Certificate afAuthorization #9503 6r" EDITION (2017) FBC NON-HVHZ EVALUATION FL6332-R8 ICP Adhesives Polyset® AH-160; (888) 774-1419 Revision 8:10/12/2017 Page 8 of 9 10.6 Exterior Research and Design, LLC. Certificate ofAuthorirotion #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION ICP Adhesives Polyset® AH-160; (888) 774-1419 1 Qz-, �",,0TR1N1'TYj1ERD Evaluation Report 02768.03.06-R8 FL6332-R8 Revision 8:10/12/2017 Page 9 of 9