HomeMy WebLinkAboutWALL PANELS ASSEMBLY INSTRUCTIONSCANNwi
STiNC.
W. Kos�' Inc
Roof & Floor ' Truss Systems
4175 Martin Highway
Palm City, FL 34990
Phone: (772) 286-3700
Fax: (772) 288-4234
Prefabricated
Wall Panels Assembly Instructions
1) Set wall panels per layout.
2) Attach panel to panel using 3, 4 V2" or 6" Simpson SDS screws 12" O.C.
Nail plywood overlaps with 8D common nails 3" O.C.
3) Attach panels to slab with Simpson 5/8" x 6" Titen HD screw anchors
every 30". Minimum 2 anchors per panel; max. 12" from corner.
4) Apply top most plate staggering breaks from panel breaks. Secure with
3" Simspon DASD screws at 24" O.C.
5) Set trusses per layout.
JOB: / Thyrring Res
ADDRESS: 10751 S Ocean Drive B8
Jensen Beach, FL 34957
A
I: NI t
PRE-ENGINEERED PATENTED WALL SYSTEM.
\\II I I I I /////
c�-T1LES�/
EN
0•
i
STATE p
Z OR ID •'�lV ����
/ANAL
WALL PANELS ARE CONNECTED
. WITH TRUSS CONNECTOR PLATES. THIS ELIMINATES WALL STRAPING
BY THE BUILDING CODE. THE WALLS ARE BUILT WITH 2X6 STUDS 16" O.C.
WITH 5/8" 4 PLY CDX PLYWOOD. THE ANCHOR BOLTS ARE SUPPLIED.
ARE SIMPSON 5/8" X 6" TITEN HD SCREW ANCHORS. TYPICAL ANCHOR SPACIN
( 4' -0". A MINIMUM OF 2 ANCHORS PER PANEL AND PLACED IN EACH CORNER
[4G TO BE DETERMINED BY THE ENGINEER OF RECORD ASCE 7-10. THE WALLS .
T WITH PRESSURE TREATED LUMBER
r
W
6e'
In 41.75 Martin Highwa I • Palm City; FL 34990 (772) 28"700
I
I
-F I_
64
'11.
1
r�
1
R
�w
�C
!
,
SG.WEBBED-9MD--ER
.,.. M BE NARED
:.
r
�
1
NOTE: ATTACH PANELS WITH 1 ROW Sd NAILS
IN LAPPING PLYWOOD AND 6' SDS SCREWS 12'
O.C. ' DOWN LAPPING STUDS. APPLY VTP IN FIELD.
A: SINGLE STUD T❑ ' PLATE = 1.5X4 PLATE
B: SILL PLATE TO CRIPPLE AND STUD= 3X5
C: TRIPPLE STUD TO PLATE = 3X5 PLATE
D: DOUBLE STUD TO PLATE = 3X5 PLATE
E: HEADER TO STUD = 3X5 PLATE
F: VERY TOP PLATE APPLIED IN FIELD
TYPICAL WALL PLATI1VG
A
A By
Milo
4175 Martin t QI;WW • FWbn City. FL 34NO • (M) M 3M .
ban
i
K
K
K
•
K
K
-F r�
k
I�
I
^G
Y
s�[cv
NDTE: ATTACH PANELS VIITH I ROW 8d NATLS
IN LAPPING PLYWOOD AND G' SDS SCREVS- 22-
_ D.C. " DOWN LAPPING; STUDS. APPLY VTP IN FIELD,.. _
-A: SINGLE STUD TO PLATE = 1.5X4 PLATE
B. SILL PLATE TO CRIPPLE AND STUD= 3X5 _
Cc TRIPPLE STUD Ta PLATE =X5 PLATE
. - D, DDU9L, SlIJD TC PLATE" = 3X.5 PLATE
E. HE1 D = PLATE
STU_
W. KOST INC.
4175 S.W. MARTIN 13WY.
PALM CITY, FL 34990
772-286-3700
Wall panel assembly instructions
W. Kost Pre -Engineered Patented wall system
Wall panels are connected together with truss connector plates.
This eliminates wall strapping required by the Building Code.
The wall are typically built with 2 x 6 studs 16" O.C. and sheeted with
tYP Y
5/8" 4ply CDX plywood.
Typical anchor spacing is every4'-0". A minimum of two anchors per panel and placed
In each corner. Spacing will be determined by the engineer of record.
1.) Set wall panels per layout.
2.) Attach panel to panel using Simpson SDS screws.
3.) Nail plywood over laps with 8d 'nails 3" O.C.
4.) Attach panels to slab with Simpson 5/8" x 6" Titen HD Screws.
Anchors every 4'-0". Minimum 2 anchors per panel, maximum 12" from corner.
This is minimum for building erection. Refer to the permit set for E.O.R.
Requirements.
5.) Apply top most plate staggering breaks from panel breaks.
Secure with Simpson 3" SDS screws at 24" O.C.
6.) Set trusses per truss layout.