HomeMy WebLinkAboutPRODUCT REPORTPage 1 of 2
•
i�j
17Y
Product Report Manufacturers Extreme Metal Fabricators, LLC.
r SW Poma Drive
Palm City, Fl. 34990
Compliant with Florida Building Code 2017 (6"n ed.)
Compliant with Florida Product Approval Rule # 61G20-3
Compliant: Keystone Certifications FILE COPY
Product: 5 V Crimp 26GA Steel Roof Panel FBC Set 1507AI
Yield strength: 50 Its] min.; Attached to min.15/32' plywood or Wood
Deck w/ min. DA2 specific gravity with screws. 24" Coverage
Rib Height 3/8"
Corrosion Resistant Compliant: FBC Sec 1S67A.3
Fastener 1(Method 1 Attachment): #9 x 1-1/2" Hex -Washer Head wood screw* to penetrate
3/26" min, thru deck or 5/8" embedment into wood plank, (*or sufficient length to meet
requirements)
Fastener 2 (Method 2,3, +& 4 Attachment): #10 x 1-1/2" Hex -Washer Head wood screw* to
penetrate 3/16" min. thru deck or 5/9" embedment into wood plank. (*or sufficient length
to meet requirements) CONCEALED FAST ENEt S OR A 1 i ACHMEiVTS
Underlayment: To be compliant with FBC Set Chart 1507.1-1 ARE THE RESPONSIBILITY OF THE
CONTRACTOR OR RECORp
Slope: Shall be in compliance with FBC See.1507.
See fastener attachment specifications above
Install Details: Table A Allowable Loads
METHOD 1
METHOD 2
METHOD 3
METHOD 4
DESIGN PRESSURV
-86 PSF
935 PSF
-102 PSF
-228 PSF
ROW SPACING
36' or-
16" a r-
8" o c-
6" Mc.
FASTENER SPACING ALONG Panel width
12" cc.
12" or-
12' D.C.
12' O.C.
FASTENER SIZE
#9
#10
#10
010
Reference Bata: ARCHITECTURAL TESnNG, INC. TST ID#:1527
UL58096&1897-042 Test Report E5893.01.4W18 03102114
Test Report F336601-450-13 22/16AS
TAS 125 03 Test Report 1D05693.02-450-18 o7/2zA4
sZQU1VALENCY-UL 1897-04 is equivafmt to teststancbrd M 1897-1� "�ln pes�oe n-M- ofsafetyZ1
i1M 1111—It -
Loth Bowden, RE dates not twee, not will acquke a Tuwi
under this evaluation.
Locke Rowden, M Is not owned, operated, or controlled
report.
TC�lti�c6t,_�21
ST. LUCII COUNTY BUILDING DIVISION
REVIEWED FOR COMPLIANCE
REVIEW Ry. Ito
DATE
PLANS A ' D PERMIT MUST BE KE T N JOB
SITE OR IV0 INSPECTIONS) WILL BE MADE
oral ini cq m9:yfadtureng or dairibui'mg products
�•• ,_
by aqy comparNDmi6a6Lture`i or t�_StribWris products under this
• �e
'0tr [CRIP�•.e.�
THESE PLANS AN® ALL PROPOSED WOR
ARE SUBJECT TO ANY CORRECTIONS
REQUIRED BY FIELD INSPECTORS THAT
MAY BE NECESSARY IN ORDER TO
COMPLY WITH ALL APPLICABLE CODES.
7/10/20181
Vi
Page 2 of 2
FfL17022.1 5V Crimp J26GA Steel), 24" Wide Roof Panel -Details
talons:
Underiayment to be compliance with current Florida Building Code (FBC)20176tl ed.
Minimum slope to be compliant with Florida Building Code 2017 610 ed., and per with Manufacturer's installation reference.
Products are compliant for State of Florida product approval per Rule 61G20-3. Compliance Method: 1-13
Engineering analysis for project specific approval by local authorities wflurisdiction is allowed by other, registered eng nears.
Fire classification is not part of this acceptance. Shear diaphragm values are outside this report.
Supportfoaming In compliance w/FSC 2017 611 ed., Chapter 22 for Steel, Chapter 23 for Wood and Chapter 16 for
Structural loading.
This report does not imply warranty, atsWalon, recommended product use outside of this report.
— Fast".
43xa-tf!'1.1n.m
.Rf0 i7-'g atop vanP A'lorRmr SY aRufPmN
Spa * aa0 d fto P:k s
FiextYa;lu$liead4aaoi Stmss
2A"
3V
�ovrwr+usswatwe+s�
Panel Profile
12"
Fasten
x -112' Min. or C#110 x 142° Min. per
file'A' Hex WasherHead Screw
aced 17 c.c. across the Panel Wdth
Panel ReferbTable"XforS,paci gAlo gP el
Overlap Length
Deck-1W2' or greater
13,Wiood, or
-VAbod plank
1
7/10/2018
CBUCK Engineering
Spsaue fu Structural Ermlr"b-._e M CBUM ur- ce&frcareCJ kutlwrjwdM 08064
Evalipti on !Report
"Ultra HT Wind & Water Seal""
)Roof Underlaymerlt
(Manufacturer:
MFM Building Products Corp.
525 Orange Street
Coshocton, Qbio 43812
(740) M-2645
jar
FIforlda Produtt Approval
# FL 11842.3 R4
Vlorida 15031ding Code 5th Edition (2017)
Method: 1- D
Category: Apol1mg
Sub - Category: Underlayment
Product: "Ultra HT Wind & Water Seal`"
,Description: Self-Adhered.Underlayment
F=d,Nle of4g alropys6nedW
Prepared by:
'1 Llmd`ner.IPJL
James L Buckner, P. E, SECS
Electrcalrallys>antl sealed dommen[s shall
ronplysslththe pnw Jonsof FAC RW&E.105-a
Florida Professional Engineer#31242
.�",%J A121"1�,��
,,
Florida Evaluation ANE ID: 1915
�5 •-..., ,C
Project Manager: Diana Galloway
_7k
Report lVo.17-131-'DHT-ER
iJo-
31?A2_
(Revises3S115-UHT-M FL118425 83)
(Date: 07/09/17
Contents:
Evaluation Report Pages 1-5
y
2017A82814:49:18-04Y30'
CBUCK, Inc dba CBUCK Englneering
Phone: (561) 491-9927 • Email: ebuck@cbuckinc.net" Wehsite,: www.cbuckinc.net
Business: 1374 Community Dr., Jupiter, FL 33458 • Corp/Mailing. 2637 E. Atlantic Blvd, 1134069, Pompano Beach, FL 33062
Page 1 of 5
I
7/10/2018
• Page 2 of 5
FLii: 1111184231R4
e��20 5
Date: 07/09117
ESUCK Engineering Page 147h1T-ER
ISAeocSIN
Structural EnQr1E_E1TM
Manufacturer:
iMFM Building ProductsCogp.
525 Orange Street
Coshocton, Ohio 43812
(740) SV-2645
www.mfmbo.com
Product Name:
"Ultra HT Wind & Water Seal'°°"
P.roductCategory:
Roofing
ProductSub-Category
Underlayment
Compliance Method:
State Product Approval Rule 616213-3. 0D (1) (d)
Product Description:
"Ultra HT Wind & Water Seal'" is self-adherimg membrane composed of a wNte,
non -slip cross-larninated polymer:f3m, laminated to a rubberized asphalt adhesive
with a split release liner designed for use as a roof underlayment in high
temperature conditions,
Product Material /
Material Type: Styrene Putadiene Styrene (SBS)
Standards:
Material shall comply with ASTM D 1970 per IFloridaBuilding Code FBC 6th Edition
(2017), Chapter 15.
Product Dimension(s)
Roll Size: 36 in, x 67 ft. rolls
Thickness: 4Sanils (nominal)
Substrate(s):
"Ultra HT Wind & Water Seal" 'has been evaluated for application to the
following substrates (Design of support is outside the scope of this evaluation):
Plywood
• Dens Deck
Installation:
General insta'Hation instructions:
"Ultra HT Wind & Water Seal" shall be installed in accordance with the attached
installation method and in compliance with applicable code sections of the ABC
6th Edition (2017), subject to the Limitations and Conditions of Use lusted in this
Evaluation Report.
Refer to installation details at the end of this report. Refer to manufacturers
installation instructions as a supplemental guide for attachment,
about:blank 7/10/2018
• Page 3 of 5
FL 9: iaL 11842.3 1R4
Date: 07109/17
RepCBUCK Engineering Page No 3 of 517-132-UHT-ER
Sps-rnaty Structural ErlQineerinq CBUMI cCeitifirateaJ'Iu,H;orkOSWCEOGa
Performance Standards:
The product described herein has demonstrated compliance with:
• ASTM D 1970-1Sa — Specification Self -adhering Polymer Modified
Bituminous Sheet Materials Used as Steep Roof Underlayment for Ice Dam
Protection
Standards Equivalency.
The ASTM D 1970-M standard version used to test the product meets the
prescribed standards in ASTM iD 1970-15a standard version adopted by the
Florida Building Code•6+th (Edition 12017) for use as evaluated in this report.
Code Compliance:
The product(s) described herein have demonstrated compliance with the
performance standards listed above as referenced in the current Florida Building
Code.
Evaluation ReportScgpe:
This product has been evaluated in compliance with the building envelope
requirements of the Florida Building Code, as related to the scope section to
Florida Product Approval Rule 616203.001.
Product Limitations and
• Deck shall be in compliance with applicable building coda.
Conditions of
Minimum slope shall be 2:12 or greater.
+ Installation is limited to use with approved roof coverings that are
mechanically fastened through the underlayment and is attached to the
sheathing or rafters,
• Not to be applied over active solvents or sealants, EPDM rubber or products
containing silicone.
• Do not expose product to direct sunlight for more than 60 days.
General Limitations and • Scope of "Limitations and Conditions of Use" for this evaluation:
Conditions of Use: This evaluation report for "Optional Statewide Approval* contains technical
documentation, specifications and installation method(s) which include
"Limitations and Conditions of Use" throughout the report in accordance with
Rule 61G20-3.005. Per Rule 6SG20-3.004, the Florida Building Commission is
the authority to approve products under'Ogtiona'l Statewide Approval".
• Option for application outside "Limitations and Conditions of Use
Rule 6$G20-3:005(1)(e) allows engineering analysis for "project specific
approval by the local authorities (saving jurisdiction in accordance with the
alternate methods and materials authorized in the Cody'. Any modification of
the product as evaluated in this report and approved by the Florida Building
Commission is outside the scope of this evaluation and will 'be the
responsibility of others.
• This report is a building code product evaluation per FLPE rule (FAC) 61615-36
to comply with Florida (product approval rule ((FAC) 61G20 3. This evaluation
reportis part of the Florida Building Commission approval for the listed code
related criteria. This report by James Buckner, IP.IE. and CBUCK Engineering is
7/10/2018
• Page 4 of 5
FL#. FL11847-31R4
Date: 07/09/17
CBUCK Engineering Page
o.: eat N40 5n a9f9T'ER
SPpclattU Stfuctural ErtQY-k-erm --N — j. 1,"."""""'""' »o,.P.
not a design certification of code compliance construction submittal
documentation, per FBC section 207, for any individual structure, site specific
or permit design.
• Design of support system is outside the scope ofthis report.
• Fare Classification is outside the scope of ,Rule 6IM", and is therefore not
included in this evaluation.
This evaluation report does not evaluate the use of this product for use in the
High Velocity Hurricane Zone code section. (Dade & Broward Counties)
Quality Assurance: The manufacturer has demonstrated compliance of ,roof panel .products in
accordance with the Florida Building Code and Rule 63U20-3.0005 13) for
manufacturing under a quality assurance program audited by an approved quality
assurance entity through Keystone Certifications, Inc. {FBC Organization ID# QUA
1924).
Referenced Data: 1. ASTM D 2970-01 Test
By PRl Construction Materials Technologies,!Inc.
VBC Organization IDN TST 1556)
Report No. iMFM-039-02 D1, Date: 8115113
2. 'Equivalency of Test Standard Certification
By James L Buckner, P.E. @ CLUCK Engineering
(FBC Organization # ANE 1916)
3. Quality Assurance
Keystone Certifications, Inc. (FBC Organization 10# QUA..1824)
MFM Building Products Corp. Licenseeai335
4. Certifiicationofindependence
By James L Buckner, IP.E. @ CLUCK Engineering
(FBC Organization # ANE 19.16)
I
7/10/2018
Page 5 of 5
IFI M FaL 118a3 1114
Date: 07/09/17
CSUCK Engineering PP gecortWo.5o 51t7HT;ER
Sp2Cidltl,l Struct-uresi Efiorwt-Mca CaucKrrcCefijxwaealsuntwriwe'or,gaa6Ge
IMIFM iBuilding (Products Corp.
Ultra MT Wind & Waxer Seal
Salf-Adhered Roofing Underpayment
General Installation Instructions:
• Product to be applied directly -to a dean dry surface.
• Prime any weathered surfaces. Dens Deck must be primed with asphalt base primer.
• Starting at the low point of the deck, peel back 12"of the release liner, align the membrane and press unto
place onto roof deck.
• Adhesive is pressure -activated, so press firmly into place using uniform pressure with a 2 3" heavy steel or
rubber roller to seams and overlap.
• IJverhp end laps a minimum of b". Side laps must be a minimum of 3".
• Store product in the carton in a dry place until readyto use. Keep product out of direct sunlight.
• Apply membrane only in fair weatherwhen the air, surface and membrane are at a minimum temperature
of: 50' p
• Not to be applied overactive solvents or sealants, EPDM rubiberor products containing silicone.
•.Donot expose,producttodirect sunlight for more than 60days.
"Ultra HT Wind & Water Seal'"" shall be installed in accordance with the attached installation method and in
compliance with applicable code sections of the FBC bth Edition (2017), subject to the IUmSations and
Conditions of Use fisted in this Evaluation Report.
(Refer to installation details at the end of this report (Refer to manufacturer's installation instructions as a
supplemental guide for attachment.
(Product Ullustratiions
;•;ULT,RA HT
WIND & WATER SEAL'"
7/10/2018
6306 Arapahoe St, Fort Pierce, FL 34982-7610 Report: 23443172
� �,g ' �G �,+'�Y"' a' '� • •� ,,c� e ; � ,..� ,�, �r .; � f - � rye-+ s', + °�'� r �:r�,�"
AW
C�b.1 'M. A�.:^� �"°il.•'x'a +i. � �;tx •,1`" �7%„�.�Y � w °� Y C,rk.e(I'� 1.�t����
°i h .� vY,� �, i ,�' v< •+++,'�� f tf F*er s;t
-ZA Yy •+min. a'+us
-IL r -.-
+Y S+rr�ad
v"aF`�,�^4t:., S T w ,� Lz"=.wde` 8„'s• -.. ,1� i
¢� � xaF cRr.+F�y .e � `� ` �' �z K at. T ( �•�'*.... '� 2� x K 3���rr �n �
04
• # 1
,._mi' z„ '"�c�'-"�,���at } "� = �3,yz-`far-� r max' � �:. �` a';{---t-•�'�` z -dE�a« ae,�y� "� y, ��7 �'"�`"� =-'rt�'`
ire., ..• j _ __ - -�''c"ae' ;t ° ° _
�p�jf�gT
ltry
it �.. .))t uxt%.I *�7 +W 5J' • .i« , ...A �. li "ry`,�,k'f *� y __kS dr �Y«. �.. ''.i,i*�tld _ .i1 Sl lzYi? 20I F