HomeMy WebLinkAboutNOABY
t. Lud90S; , Lll'CIE COUNTY BUILDING DIV ION
REVIEWED FOR COMPLIANCE
REVIEWE Y
DATE
PLANS AND PERMIT MUST BE KE ON JOB
IIAM �I�IADE SITE OR NO INSPECTION(S) W BE MADE MICONTROL
COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
DEP TMENT OF REGULATORY AND ECONOMIC RESOURCES (RE, Miami, Florida 33175-2474
BOA � AND CODE ADMINISTRATION DIVISION T (786)315-2590 F (786) 31525-99
NOTICE OF ACCEPTANCE (NOA) www.miamidadc.ov/econon»
Cert#inTeed Corporation
20 oores Road b Dq
Mal ern, PA 19355 FILE COPY 04"o-
SC,JiIPE:
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
doc mentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
use in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
Thi NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
pro uct or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
ma ner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
sus end the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it its determined by Miami -Dade County Product Control Section that this product or material fails to meet the
req trements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
D J
SCRIPTION: CertainTeed Modified Bitumen Roofing Systems over Wood Decks.
LBELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
staement:"Miami-Dade County Product Control Approved", unless otherwise noted herein.
RNEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
inie applicable building code negatively affecting the performance of this product.
,RMINATION of this NOA will occur after the expiration date or if there has been a revision or change in -the
:erials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
his NOA shall be cause for termination and removal of NOA.
ERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
ition date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
entirety.
'ECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
be available for inspection at the job site at the request of the Building Official.
NOA renews NOA #14-0529.02 and consists of pages 1 through 42.
submitted documentation was reviewed by Alex Tigera.
CONCEALED FASTENERS OR ATTACH1,1Ea J T S
ARE THE RESPONSIBILITY OF THE
CONTRACTOR OR RECORD
THESE PLANS AND ALL PROPOSED WORK
ARE SUBJECT TO ANY CORRECTIONS
REQUIRED BY FIELD INSPECTORS THAT
MAY BE NECESSARY IN ORDER TO '
COMPLY WITH ALL APPLICABLE CODES.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 1 of 42 4
FI
FING SYSTEM APPROVAL
on"
Roofing
;ategory:
Modified Bitumen
APP/SBS
Type:
Wood
num Design Pressure:
-127.5 psf.
DE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Pro uc
Dimensions
Specification
Description
eather/Empire Base
39 3/g" x 65' 10";
ASTM D 4601, Type Asphalt coated, fiberglass reinforced
Roll weight: 70 lbs.
II
base sheet.
(2 squares)
UL Type G2
;las Base Sheet
39 3/8" x 98'9'; Roll
ASTM D 4601, Type Modified Bitumen coated fiberglass
weight: 90 lbs.
II
base sheet.
(3 squares)
UL Type G2
istic Base 20
39 3/s" x 49' 6"; Roll
ASTM D 6163,
Modified Bitumen coated fiberglass
weight: 90 lbs.
Grade S, Type I
base sheet.
(1.5 squares)
jas Ply Sheet Type IV
39 3/s" x 1647'; Roll
ASTM D 2178, Type Fiberglass, asphalt impregnated ply sheet.
weight: 38 lbs.
IV
(5 squares)
UL Type G1
jas Premium Ply Sheet
39 3/s" x 1647'; Roll
ASTM D 2178, Type Fiberglass,. asphalt impregnated ply
VI
weight: 401bs.
VI
sheet.
(5 squares)
UL Type G1
astic STA
39 3/8" x 32' 10' ; Roll
ASTM D 6222,
Smooth surfaced APP Modified
weight: 871bs.
Grade S, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
astic GTA
39 3/s" x 32' 10"; Roll
. ASTM D 6222,
Granule surfaced APP Modified
weight: 105 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
astic GTA-FR
39 3/8" x 32' 10' ; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 105 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application.
astic GMS
39 3/s" x 32' 10'; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 94 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18 4
Page 2 of 42
Fli
DE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions
Specification
Description
istic FR-P
39 3/a" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type I
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
istic Premium FR-P
39 3/8" x 32' 10'; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 101 lbs.
Grade G, Type II
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
astic FR Dual Cap
39 3/8" x 32' 10"; Roll
ASTM D 6162,
Granule surfaced SBS modified
weight: 103 lbs.
Grade G, Type I
bitumen membrane with a nonwoven
(1 square)
polyester/fiberglass composite mat
reinforcement for use in cold or mop
applications.
astic FR Cap 30
39 3/8" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
weight: 86 lbs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications.
astic FR Cap 30 T
39-3/8" x 32' 10'; Roll
ASTM D 6163,
Granule surfaced SBS Modified
weight: 100 lbs.
Grade G, Type I
Bitumen membrane with fiberglass
(1 square)
mat reinforcement for torch
application.
astic Base 20 T
39-3/8" x 33'; Roll
ASTM D 6163,
Modified Bitumen, coated fiberglass
Weight: 81 lbs.
Grade S, Type I
base sheet for torch application.
(1 square)
astic FR Cap 30 CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
weight: 88 lbs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications. Covered with reflective
CoolStar Coating.
astic FR Cap 30 T
39 3/8" x 32' 10"; Roll
ASTM D 6163,
Fire resistant, granule surfaced SBS
Star
weight: 102 tbs.
Grade G, Type I
Modified Bitumen membrane with
(1 square)
fiberglass mat reinforcement for mop
applications. Covered with reflective
CoolStar Coating.
astic GTA CoolStar
39 3/s" x 32' 10"; Roll "
ASTM D 6222,
Granule surfaced APP Modified
weight: 106 lbs.
Grade G, Type_I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application. Covered with reflective
CoolStar Coating.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 3 of 42
Y
Fl
DE NAMES OF PRODUCTS MANUFACTURED OR LABELED BY APPLICANT:
TABLE 1
Test
Product
Product
Dimensions
Specification
Description
astic GTA-FR CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6222,
Granule surfaced APP Modified
weight: 1061bs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for torch
application. Covered with reflective
CoolStar Coating.
astic GMS CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Granule surfaced SBS Modified
weight: 97 lbs.
Grade G, Type I
Bitumen membrane with non -woven
(1 square)
polyester mat reinforcement for mop
application. Covered with reflective
CoolStar Coating.
astic FR-P CoolStar
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
weight: 103 lbs.
Grade G, Type I
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Covered with reflective CoolStar
Coating.
astic Premium FR-P
39 3/s" x 32' 10"; Roll
ASTM D 6164,
Fire resistant, granule surfaced SBS
Star
weight: 103 lbs.
Grade G, Type II
Modified Bitumen Membrane with
(1 square)
non -woven polyester mat
reinforcement for mop application.
Covered with reflective CoolStar
Coating.
astic Ultra Poly SMS
39 3/8" x 32' 10"; Roll
ASTM D 6164,
Smooth surfaced SBS Modified
Sheet
weight: 901bs. (1
Grade S, Type I
Bitumen Membrane with non -woven
squares)
polyester mat reinforcement for mop
applications.
iase Base Sheet
36" x 98' 9"; Roll
ASTM D 4601, Type Asphalt coated, fiberglass base sheet.
weight: 75 lbs.
II,
(3 squares)
UL Type G2
astic Poly SMS Base
39 3/8" x 64' 3"; Roll
ASTM D 4601,
Modified Bitumen coated polyester
weight: 90 lbs.
Grade S, Type II
base sheet.
(2 squares)
UL Type G2
mite Venting Base Sheet
39 3/8" x 32' 10"; Roll
ASTM D 3909
Mineral Surfaced fiberglass reinforced
weight: 85 lbs.
ASTM D 4897, Type buffer sheet.
(1 square)
II
UL Type G3
astic APP Base T
39 3/8" x 65' 4"; Roll
ASTM D 6509
Modified Bitumen coated fiberglass
weight: 100 lbs.
base sheet.
(2 squares)
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 4 of 42
Flint 'astic Ultra Glass SA 39 'Is" x 33' 11' ; Roll
weight: 73 lbs.
(1 square)
Blac DiamondTM Base Sheet 36" x 687'; Roll
weight: 78 lbs.
(2 squares)
INSULATIONS:
ASTM D 1970 Self -adhering, fiberglass reinforced,
SBS modified bitumen base/ply sheet.
ASTM D 1970 Self -adhering fiberglass. reinforced
modified bitumen base sheet
TABLE, 2
Product Name
Product Description
Flini
Board ISO
Polyisocyanurate foam insulation
Flin
BoardH ISO
Polyisocyanurate foam insulation
AC
pam -11
Polyisocyanurate foam insulation
Den
Den
(Deck
(Deck Prime
Water resistant gypsum board
Water resistant gypsum board
H-S
ield
Polyisocyanurate foam insulation
E. IIGY 3
ENiiGY 3 25 PSI
Polyisocyanurate foam insulation
Polyisocyanurate foam insulation
Muliii-Max FA-3
Polyisocyanurate foam insulation
SE UROCK Gypsum -Fiber Roof Board
homogenous fiber reinforced
Str
Ftodek High Density Fiberboard
High Density Wood Fiber Insulation
Ro
Fes
f Insulation
IoBoard
board
Expanded perlite and fiber insulation
Manufacturer
With Current NOA
CertainTeed Corporation
CertainTeed Corp.
Atlas Roofing Corp.
Georgia Pacific Gypsum LLC
Georgia Pacific Gypsum LLC
Hunter Panels LLC
Johns Manville Corp.
Johns Manville Corp.
RMax Operating, LLC
USG Corp.
Blue Ridge Fiberboard, Inc.
Johns Manville Corp.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 5 of 42
FASTENERS:
TABLE 3
Product Product
Name Description
Trufast #12 DP Fastener Insulation fastener for wood
and steel decks
Trufast 3" Metal Galvalume steel plate
Insulation Plate
F1intFast 412
F1intFast 3" Insulation
Plate
5. FlintFast #14
Simplex MAXX Cap
OMG #12 Standard
Roofgrip
3. OMG 3" Galvalume Steel
Plate
9. Trufast #14 HD Fastener
10. OMG Heavy Duty
11.
3 in. Round Metal Plate
12.
AccutTrac Hextra
13.
AccuTrac Plate
14.
AccuTrac Flat Bottom
Plate
15.
Millennium One Step
Foamable Adhesive
16. Millennium PG-1 Low
Viscosity Insulation
Adhesive
17. Insta Stik Quik Set
Insulation
Coated, carbon steel screw
Galvalume AZ50 steel plate
Insulation fastener for wood
and steel decks
Polymer fastner
Insulation fastener for wood
and steel.
Galvalume stress plate
Insulation fastener for wood
and steel decks
Insulation and membrane
fastener
Galvalume AZ50 steel plate
Carbon steel fastener
Galvalume stress plate.
A2-SS aluminized steel plate
Manufacturer
Dimensions (With Current NOA)
various Altenloh, Brinch & Co. U.S.,
Inc.
3" round Altenloh, Brinch & Co. U.S.,
Inc.
various CertainTeed Corp.
3" round CertainTeed Corp.
various CertainTeed Corp.
1" long Simplex Nails, Inc.
various OMG, Inc.
3" round OMG, Inc.
various Altenloh, Brinch & Co. U.S.,
Inc.
Various OMG, Inc.
3" round OMG, Inc.
Various OMG, Inc.
3" square OMG, Inc.
3" square OMG, Inc.
Polyurethane two component
1.5 liters
Adco Products, Inc. d.b.a.
high rise insulation adhesive
Royal Adhesives & Sealants,
Inc.
Polyurethane two component
1.5 liters
Adco Products, Inc. d.b.a.
low rise insulation adhesive
Royal Adhesives & Sealants,
Inc.
Polyurethane one component
It is supplied
The Dow Chemical Company
moisture curing adhesive
in pressurized
cylinders with
a net weight
of 23 lbs.,
with a total
unit weight of
301bs.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 6 of 42
FASTENERS:
TABLE 3
Faa'tener
Product Product Manufacturer
Nu—;';ber
Name Description Dimensions (With Current NOA)
18.
OMG OlyBond 500 Spray polyurethane foam 10 gal. bag -in- OMG, Inc.
Adhesive insulation adhesive box set and
1.5 liters
SpotShot
cartridge
19. OMG OlyBond 500 Green Spray polyurethane foam 10 gal. bag -in- OMG, Inc.
Adhesive insulation adhesive box set and
1.5 liters
SpotShot
cartridge
AP
(ROVED SURFACING/COATING OPTIONS:
TABLE 4
Cho
en components must be applied according to manufacturer's application instructions. Any coating, listed
beloll
, used as a surfacing, must be listed within a current NOA.
System
Number Manufacturer Application
1. Generic Gravel applied at 400 lbs/sq., adhered with flood coat of asphalt at
60 lbs/sq.
2. Generic Slag applied at 3001bs/sq., adhered with flood coat of asphalt at 60
lbs/sq.
3. Karnak Corp. Karnak (#97 AF) Fibrated Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
4. CertainTeed Corp. F1intCoat A-150 applied at an application rate of 1.5 gal/sq.
5. Gardner Asphalt Corp. APOC #212 Fibered Aluminum Roof Coating applied at an
application rate of 1.5 gal/sq.
6. Gardner Asphalt Corp. APOC 4400 Sunbrite applied at an application rate of 3 gal./sq.
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 7 of 42
U
U
ENCE SUBMITTED:
Test Agency/Identifier
Name
Report
Date
y Mutual Research Corp.
FM 4470
3Y8A1.AM
03/23/96
FM 4470
OD3A3.AM
04/04/97
FM 4470
2DOAO.AM
12/23/98
FM 4470
1D7A4.AM
11/09/98
FM 4470
3039046
06/15/10
FM 4470
3048520
09/19/13
Nriters Laboratories, Inc.
UL 790
R11656
01/11/13
States Testing Company
ASTM D 5147
97457-4
06/03/88
ASTM D 5147
97-457-2R
12/02/87
ntum Technologies, Inc.
ASTM D6164
AX31 G8F
06/05/09
IJERD
TAS 114(J)
3507.08.99-1
04/18/01
TAS 114(J)
3504.06.01-1
06/05/01
TAS 114
3521.07.04
07/29/04
TAS 114
3533.01.06
01/06/06
TAS 114 (H)
Letter
04/05/06
TAS 117 (13)
3503.10.06
10/10/06
TAS 117 (13)
06490.04.07-R1
06/27/07
TAS 117 (B)/ ASTM D 6862
C8500SC.11.07
11/30/07
TAS 114
C8370.08.08
08/19/08
FM 4470, TAS 114, FM 4470,
C8370.08.08-R1
10/05/09
TAS 114(J)
ASTM Physical Properties
C10080.09.08-R4
03/25/10
TAS 114(H), TAS 117(B), TAS
C30560.06.10
6/10/10
114(J)
FM 4470, TAS 114
C32830.07.10
7/20/10
ASTM D6164/D4798
C31410.01.11-2
01/10/11
TAS 117B
C35500.02.11
02/09/11
ASTM D4601
C40050.09.12-1
09/28/12
ASTM D'1876
C35460.05.11
06/16/11
ASTM DI876,.TAS 114 (H),
C42110.08.12
08/13/12
TAS 111(B)
FM 4474/TAS 114
C39670.08.12
08/20/12
ASTM D1970
C40050.09.12-2
09/28/12
ASTM D5147/D4798
C31410.10.10-R1
11/01/12
ASTM D5147/D4798
C31410.01.11-1-R1
11/01/12
ASTM D4798
C31410.01.11-2A-Rl
02/21/13
ASTM D4798
C31410.12.13
12/05/13
ASTM D6222
C40050.12.13-R1
12/31/13
TAS 117, TAS 114
C30310.12.09-R1
03/07/14
ASTM D1876, TAS 114 (H),
C45620.03.14
03/27/14
FM 4474
ASTM D 1876, TAS 114 (H),
C47320.03.14-R1
04/01/15
FM 4474
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 8 of 42
PRI
ONCE SUBMITTED:
Test Agency/Identifier
ion Materials
LLC
Name
Report
Date
ASTM D4601-04 (2012), Type II
CTR-SC11145.09.16-
09/19/16
3A
ASTM D6163
CTC-066-02-01
08/09/11
ASTM D6222
CTC-071-02-01
08/08/11
ASTM D6222
CTC-070-02-01
08/09/11
ASTM D6164/D4798
CTC-093-02-01
08/09/11
ASTM D4601
CTC-126-02-01
03/12/12
ASTM D2178
CTC-122-02-01
03/13/12
ASTM D2178
CTC-123-02-01
03/13/12
ASTM D4601
CTC-127-02-01
03/13/12
ASTM D6163
CTC-128-02-01
06/11/12
ASTM D6163
CTC-129-02-01
06/11/12
ASTM D6164
CTC-132-02-01
06/11/12
ASTM D6164
CTC-161-02-01
05/09/13
ASTM D6162
CTC-183-02-01
10/02/13
ASTM D6164
CTC-190-02-01
12/02/13
ASTM D1970
CTC-199-02-01
01/22/14
ASTM D6163
CTC 319-02-01
08/22/17
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 9 of 42
ibrane Type: APP Modified
: Type 1: Wood, Non -Insulated
Description: 19/32" or greater plywood or wood plank attached with 8d ring shank nails spaced 6" o.c. at
wood joists spaced maximum 24" o.c.
Type E(3): Base sheet mechanically fastened.
All Gen d System Limitations apply.
Basle Sheet: qiee;t,�F�Iintlastic
Weather/Empire Base Sheet Yosemite Venting Base Sheet, Flexiglas Base
Poly SMS Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Glasbase Base
Sheet or Flintglas Premium Ply Sheet Type VI mechanically attached as detailed below.
Base sheet shall be lapped 4" and fastened with 11 ga. annular ring shank nails and approved tin
caps 8"o.c. in the lap and three rows staggered in the center of the sheet 8"o.c.
heet: One ply of All Weather/Empire Base Sheet, Flintlastic Ultra Poly SMS Base Sheet, Glasbase
onal) Base Sheet, Flexiglas Base Sheet, Flintlastic Base 20, Flintlastic Poly SMS Base Sheet or one
or more plies of Flintglas Ply Sheet Type IV or Flintglas Premium Ply Sheet Type VI adhered in
a full mopping of approved asphalt applied within the EVT range and at a rate of 20-40 lbs./sq.
or one ply of Black Diamond Base Sheet or Flintlastic Ultra Glass SA self -adhered or Flintlastic
STA or Flintlastic APP Base T torch adhered,
brave.
lintlastic GTA Flintlastic GTA CoolStar, Flintlastic GTA-FR or Flintlastic GTA-FR CoolStar
torch adhered to base/ply sheet.
Any of the approved surfacing/coating options listed in Table 4.
1)
Design -52.5 psf. (See General Limitation #7)
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18 i
Page 23 of 42 j
WOOD DECK SYSTEM LIMITATIONS:
slip sheet is required with Ply 4 and Ply 6 when used as a mechanically fastened base or anchor sheet.
GENERAL LIMITATIONS:
1. Fire classification is not part of this acceptance; refer to a current Approved Roofing Materials Directory for fire*
ratings of this product.
2. Insulation may be installed in multiple layers. The first layer shall be attached in compliance with Product Control
Approval guidelines. All other layers shall be adhered in a full mopping of approved asphalt applied within the
EVT range and at a rate of 20-40 lbs./sq., or mechanically attached using the fastening pattern of the top layer
3. All standard panel sizes are acceptable for mechanical attachment. When applied in approved asphalt, panel size
shall be 4' x 4' maximum.
4. An overlay and/or recovery board insulation panel is required on all applications over closed cell foam insulations
when the base sheet is fully mopped. If no recovery board is used the base sheet shall be applied using spot
mopping with approved asphalt, 12" diameter circles, 24" o.c.; or strip mopped 8" ribbons in three rows, one at
each side lap and one down the center of the sheet allowing a continuous area of ventilation. Encircling of the
strips is not acceptable. A 6" break shall be placed every 12' in each ribbon to allow cross ventilation. Asphalt
application of either system shall be at a minimum rate of 12 lbs./sq.
Note: Spot attached systems shall be limited to a maximum design pressure of -45 psf.
5. Fastener spacing for insulation attachment is based on a Minimum Characteristic Force (F') value of 275 IV., as
tested in compliance with Testing Application Standard TAS 105. If the fastener value, as field-tested, are below
275 lbf. insulation attachment shall not be acceptable.
6. Fastener spacing for mechanical attachment of anchor/base sheet or membrane attachment is based on a minimum
fastener resistance value in conjunction with the maximum design value listed within a specific system. Should
the fastener resistance be less than that required, as determined by the Building Official, a revised fastener spacing,
prepared, signed and sealed by a Florida registered Professional Engineer, Registered Architect, or Registered
Roof Consultant may be submitted. Said revised fastener spacing shall utilize the withdrawal resistance value
taken from Testing Application Standards TAS 105 and calculations in compliance with Roofing Application
Standard RAS 117.
7. Perimeter and corner areas shall comply with the enhanced uplift pressure requirements of these areas. Fastener
densities shall be increased for both insulation and base sheet as calculated in compliance with Roofing
Application Standard RAS 117. Calculations prepared, signed and sealed by a Florida registered Professional
Engineer, Registered Architect, or Registered Roof Consultant (When this limitation is specifically referred
within this NOA, General Limitation #9 will not be applicable.)
8. All attachment and sizing of perimeter nailers, metal profile, and/or flashing termination designs shall conform to
Roofing Application Standard RAS I I I and applicable wind load requirements.
9. The maximum designed pressure limitation listed shall be applicable to all roof pressure zones (i.e. field,
perimeters, and corners). Neither rational analysis, nor extrapolation shall be permitted for enhanced fastening at
enhanced pressure zones (i.e. perimeters, extended corners and corners). (When this limitation is specifically
referred within this NOA, General Limitation #7 will not be applicable.)
10. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
END OF THIS ACCEPTANCE
NOA No.: 17-1003.04
Expiration Date: 06/19/23
Approval Date: 04/19/18
Page 42 of 42