HomeMy WebLinkAboutEVALUATION REPORT�p NEMO etc.
SCANNED Certificate of Authorization #32455
BY 353 Christian Street, Unit #13
s lade county Oxford, CT 06478
I� (203) 262-9245
NGINEER EVALUATE TEST CONSULT CERTIFY
EVALU ,TION REPORT
Polygla°s USA, Inc. Evaluation Report P12060.02.09-R24
1111 hest Newport Center Drive FL5259-R28
Deerfield Beach, FL 33442 Date of Issuance: 02/24/2009
(954) 2t 3-1230 Revision 24: 01/24/2018
SCOPE:
This E aluation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
constr 'ction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E.
for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The products
described herein have been evaluated for compliance with the 6t Edition 2017 Florida Buildin Code sections noted
herein. �I
LABELIN : Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this
Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. of any changes to the
produ (s), the Quality Assurance or the production facility location(s). NEMOIetc. requires a complete review of this
Evalua ion Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "MEMO l etc. Evaluated" may be displayed in
adverti I ing literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECT 'ION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distribi, hors and shall be available for inspection at the job site at the request of the Building Official.
This Ev„ luation Report consists of pages 1 through 14.
Prepared by:
Robe !U.M. Nieminen, P.E.
Florida „egistration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized by Robert Nieminen,
P.E. on 01/24/2018. This does not serve as an electronically
signed document.
CERTIFICII' TION OF INDEPENDENCE:
1. NEMOIetc. does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
disl ributing products it evaluates.
2. NE O I etc. is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
3. Rol' lert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Rot'pert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. Thin is a building code evaluation. Neither NEMO I etc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
ROOFING;
1.
2.
3.
i
v �
ONEMOletc.
EVALUATION:
duct Category: Roofing
b-Category: Underlayment
mpliance Statement: Roof Underlayments, as produced by Polyglass USA, Inc., have demonstrated compliance with the
lowing sections of the 6 E ition 201�7 F on a Bui in Code through testing in accordance with the following Standards.
mpliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth herein.
Jon
Property
Standard
Year
1.3.1
Wind Uplift
FM 4474
2011
13.1
Wind Uplift
UL 1897
2012
7.2.3 / 1507.1.1
Physical Properties
ASTM D226
2009
1.2.4 / 1507.1.1, 1507.2.9.2
Physical Properties
ASTM D1970
2015
7.3.3
Physical Properties
FRSA/TRI April 2012
2012
7.11.2
Physical Properties
ASTM D6164
2011
7.11.2
Physical Properties
ASTM D6222
2011
110
Accelerated Weathering
ASTM D4798
2011
ntt1t V
Examination
Reference
Date
M Approvals (TST 1867)
Wind Uplift
3004091
01/12/2000
RI (TST 5878)
Physical Properties
PRIO1111
04/08/2002
RI (TST 5878)
Physical Properties
PUSA-005-02-01
01/31/2002
RI (TST 5878)
Physical Properties
PUSA-013-02-01
12/23/2002
RI (TST 5878)
Physical Properties
PUSA-013-02-02
12/23/2002
RI (TST 5878)
Physical Properties
PUSA-013-02-03
12/23/2002
RI (TST 5878)
Physical Properties
PUSA-018-02-01
07/14/2003
RI (TST 5878)
Physical Properties
PUSA-028-02-01
07/13/2005
RI (TST 5878)
Physical Properties
PUSA-033-02-01
01/12/2006
RI (TST 5878)
Physical Properties
PUSA-035-02-01
09/29/2006
RI (TST 5878)
Physical Properties
PUSA-055-02-02
12/10/2007
RI (TST 5878)
Physical Properties
PUSA-061-02-02
01/28/2008
RI (TST 5878)
Physical Properties
PUSA-076-02-01
02/22/2008
RI (TST 5878)
Physical Properties
PUSA-083-02-01
04/14/2008
RI (TST 5878)
Physical Properties
PUSA-088-02-01
07/29/2009
1TI (TST 2508)
Physical Properties
JX201-17A
04/01/2008
ITI (TST 2508)
Physical Properties
RX14E8A
01/29/2009
RD (TST 6049)
Physical Properties
11752.09.99-1
02/08/2000
RD (TST 6049)
Wind Uplift
11757.08.01-1
08/13/2001
RD (TST 6049)
Wind Uplift
11776.06.02
01/16/2003
RD (TST 6049)
Physical Properties
02200.07.03
07/14/2003
RD (TST 6049)
Wind Uplift
P1740.01.07
01/04/2007
RD (TST 6049)
Physical Properties
P5110.04.07-1
04/11/2007
RD (TST 6049)
Wind Uplift
P9260.03.08
03/21/2008
RD (TST 6049)
Physical Properties
P13450.08.09
08/13/2009
RD (TST 6049)
Wind Uplift
P30540.11.09-R1
11/30/2009
RD (TST 6049)
Physical Properties
P11030.11.09-1
11/30/2009
RD (TST 6049)
Wind Uplift
P11030.11.09-2
11/30/2009
RD (TST 6049)
Physical Properties
P11030.11.09-3
11/30/2009
RD (TST 6049)
Physical Properties
P33360.06.10
06/25/2010
RD (TST 6049)
Physical Properties
P33370.03.11
03/02/2011
RD (TST 6049)
Physical Properties
P33370.04.11
04/26/2011
RD (TST 6049)
Physical Properties
P37300.10.11
10/19/2011
ETC, I.I.C. Evaluation Report P12060.02.09-R24
to of Authorization ✓132455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-1128
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 2 of 14
4.
ONEMOjetc.
roxity Examination Reference Date
RD (TST 6049) Physical Properties P40390.08.12-1 08/06/2012
RD (TST 6049) Physical Properties P40390.08.12-2 08/07/2012
RD (TST 6049) Physical Properties C41420.09.12-3 09/11/2012
RD (TST 6049) Wind Uplift P39680.03.13 03/04/2013
RD (TST 6049) Physical Properties P45370.04.13 04/26/2013
RD (TST 6049) Wind Uplift P1738.02.07-R2 04/29/2013
RD (TST 6049) Wind Uplift 11757.04.01-1-R1 04/30/2013
RD (TST 6049) Wind Uplift P41630.08.13 08/06/2013
RD (TST 6049) Wind Uplift P11751.05.03-R3 11/26/2013
RD (TST 6049) Wind Uplift P11781.11.03-R1 11/26/2013
RD (TST 6049) Physical Properties P45270.05.14 05/12/2014
1RD (TST 6049) Physical Properties 6020.07.14-1 09/08/2014
RD (TST 6049) Physical Properties 6020.09.14-2 09/08/2014
RD (TST 6049) Physical Properties 6020.09.14-3 09/08/2014
RD (TST 6049) Physical Properties 6020.09.14-4 09/08/2014
RD (TST 6049) Physical Properties 6020.09.14-5 09/08/2014
RD (TST 6049) Physical Properties 6020.09.14-6 09/08/2014
,�RD (TST 6049) Physical Properties P46520.10.14 10/03/2014
RD (TST 6049) Physical Properties P43290.10.14 10/17/2014
RD (TST 6049) Physical Properties PLYG-SC7550.03.15 03/24/2015
RD (TST 6049) Physical Properties P40390.04.15 04/03/2015
RD (TST 6049) Physical Properties P44360.10.14-R1 05/18/2015
RD (TST 6049) Physical Properties PLYG-SC8080.05.15-1 05/20/2015
RD (TST 6049) Wind Uplift PLYG-SC8905.05.16-1 05/17/2016
RD (TST 6049) Physical Properties PLYG-SC8080.07.16 07/16/2016
RD (TST 6049) Wind Uplift PLYG-SC12025.10.16 10/12/2016
RD (TST 6049) Physical Properties PLYG-SC13040.12.16 12/27/2016
RD (TST 6049) Physical Properties PLYG-SC11900.03.17 03/10/2017
RD (TST 6049) Physical Properties PLYG-SC12115.08.17 08/08/2017
CC -ES (EVL 2396) IBC Compliance ESR-1697 11/01/2014
iami-Dade (CER 1592) HVHZ Compliance NOA 14-0717.08 01/22/2015
lolyglass USA Manufacturing Affidavit Products Current 02/18/2009
olyglass USA P/L Affidavit Mule -Hide Cross Ltg 03/01/2008
olyglass USA Materials Affidavit Polystick SA Compound 08/18/2011
L, LLC. (QUA9625) Quality Control Service Confirmation Exp. 10/05/2018
I
RODUCT DESCRIPTION:
:1 Mechanically Fastened Underlayments -
1.1 Elastobase is a fiberglass reinforced, SBS modified bitumen base sheet.
1.1.2 Elastobase P is a polyester -reinforced, SBS modified bitumen base sheet.
II
l .1.3 Polyglass G2 Base is a fiberglass -reinforced, asphaltic base sheet.
.1.4 Polyglass APP Base is a fiberglass -reinforced, APP modified bitumen base sheet.
4.2', SeWAdhering Underlayments
C2.1 Polystick MTS or Polystick MTS PLUS is a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass
�i fiber reinforced, surfaced with polyolefinic film surface; meets FRSA/TRI April 2012.
1 .2.2 Polystick IR-Xe is a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with an
aggregate surface; meets ASTM D1970.
2.3 Polystick TU Plus is a nominal 80-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with a
polyester fabric surface; meets ASTM D1970 and FRSA/TRI April 2012.
ETC, I.I.C. Evaluation Report P12060.02.09-R24
to ofAuthorizotion #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-1128
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 3 of 14
ii
fONEMOJetc.
12.4 Polystick TU P is a nominal 130-mil thick rubberized asphalt waterproofing membrane, glass-fiber/polyester
reinforced, with a granular surface; meets FRSA/TRI April 2012.
->i i 2.5 Po stir TU Max is a nomina 1160-m t Ic ru erized as a t water roo in membrane wit a 19 m2 o ester
a ric su ace; meets ASTM 01970 and F.RSA RI A ri 2012.
L2.6 Polyflex SAP, Polyflex SAP FR, Mule -Hide SA-APP Cap Sheet and Mule -Hide SA-APP Cap Sheet (FR) are polyester
reinforced, APP modified bitumen cap sheets; meet FRSA/TRI April 2012.
S.
2.7 Polystick Dual ProTM is a nominal 60-mil thick dual -layer rubberized asphalt waterproofing membrane, fiberglass
reinforced, with a polyester fabric surface; meets ASTM D1970.
2.8 Polystick Tile ProTm is a nominal 60-mil thick dual -layer rubberized asphalt waterproofing membrane, fiberglass
reinforced, with a polyester fabric surface; meets ASTM D1970 and FRSA/TRI April 2012.
2.9 Polystick MU-X is a nominal 54-mil thick dual -layer rubberized asphalt waterproofing membrane, fiberglass
reinforced, with a polypropylene film surface; meets AC188 and physical requirements of ASTM D1970 (See Section
5.8).
3 Mechanical(y,_,Fastened'and/or Bonded Underlayments
3.1 Elastoflex G TU is a polyester reinforced, modified bitumen the underlayment composed of a sand -surfaced SBS
modified bitumen back -side and granule -surfaced APP modified bitumen top -side. Elastoflex G TU is for use as an
alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single Ply System" from FRSA/TRI April
2012 04-12 beneath mechanical) fastened the roofs stems or Hot Asphalt applied "Ca Sheet" in the "Two PI
� ( ) Y Y P PP� P Y
System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened or adhered the roof systems.
.2 Elastoflex S6 G and Elastoflex S6 G FR are polyester reinforced, SBS modified bitumen cap sheets; meet ASTM D6164.
Elastoflex S6 G and Elastoflex S6 G FR are for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380,
Class M) in the "Single Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems.
Elastoflex S6 G is for use as an alternate to Hot Asphalt applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI
April 2012 (04-12) beneath mechanically fastened or adhered tile roof systems. Elastoflex S6 G FR is for use as an
alternate to Hot Asphalt applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath
mechanically fastened the roof systems.
.3 Polyflex G and Polyflex G FR are polyester reinforced, APP modified bitumen cap sheets; meet ASTM D6222.
Polyflex G is for use as an alternate to Heat Applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012
(04-12) beneath mechanically fastened or adhered the roof systems. Polyflex G FR is for use as an alternate to Heat
Applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile
roof systems.
.1 This is a building code evaluation. Neither NEMOIetc. nor Robert Nieminen, P.E. are, in any way, the Designer of
Record for any project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or
design guidance unless retained specifically for that purpose.
.2 This Evaluation Report is not for use in the HVHZ.
.3 Fire Classification is not part of this Evaluation Report; refer to current Approved Roofing Materials Directory for fire
ratings of this product.
.4 Polyglass Roof Underlayments may be used with any prepared roof cover where the product is specifically referenced
within FBC approval documents. If not listed, a request may be made to the Authority Having Jurisdiction for
approval based on this evaluation combined with supporting data for the prepared roof covering.
ETC, I.I.C. Evaluation Report P12060.02.09-R24
to of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 4 of 14
I
ONEMOjetc.
.5 Allowable Roof Covers:
.I
!; TABLE 1'.100F,COVER OPTIONS" , .
nderlayment
Asphalt Shingles
Nail -On Tile
Foam -On Tile
Metal
Wood Shakes o
WShingles
Slate
lastobase
Yes
Yes
(Base Sheet In 2-ply system)
Yes
(Base Sheet in 2-ply system)
Yes
Yes
Yes
lastobase P
Yes
Yes
(Base Sheet in 2-ply system)
Yes
(Base Sheet in 2-ply system)
Yes
Yes
Yes
�olyglass G2 Base
it
No
Yes
(Base Sheet in 2-ply system)
Yes
(Base Sheet in 2-ply system)
No
No
No
Ilolyglass APP Base
11
No
Yes
(Base Sheet in 2-ply system)
Yes
(Base Sheet in 2-ply system)
No
No
No
olystick MTS or MTS PLUS
Yes
Yes
No
Yes
Yes
Yes
olystick IR-Xe
Yes
No
No
No
Yes
Yes
plystick TU P
No
Yes
Yes (See 5.5.1)
No
No
No
olystickTU Plus
Yes
Yes
Yes (See 5.5.1)
Yes
Yes
Yes
o stic TU Ma
No
es
Yes (See 5.5.1)
Yes
No
No
„olystick Dual Pro
Yes
No
No
Yes
Yes
Yes
,'olystickTile Pro
Yes
Yes
Yes (See 5.5.1)
Yes
Yes
Yes
olystick MU-X
Yes
No
No
Yes
Yes
Yes
lastoflex S6 G
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
lastoflex S6 G FR
Yes
Yes
No
No
Yes
Yes
lastoflex G TU
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
„olyflex G
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
„olyflex G FR
Yes
Yes
No
No
Yes
Yes
„olyflex SAP or SAP FR
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
ule-Hide SA-APP Cap Sheet
1r SA-APP Cap Sheet (FR)
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
I
1.5.1 "Foam -On Tile" is limited to use of the following Approved the adhesives / underlayment combinations.
TABLE
1A: ALLOWABLE TILE ADHESIVE UNDERLAYMENT COMBINATIONS)
Adhesive
Florida Product
Underlayments
Approval
AP Foam Touch 'n Seal StormBond Roof
rile Adhesive
FL14506
Polystick TU Plus, Polystick TU Max
ow TileBond"
FL22525
Polystick TU P, Polystick TU Plus, Polyflex SAP or Tile Pro
Polystick TU P, Polystick TU Plus, Polystick TU Max, Polystick Tile Pro,
CP Adhesives Polyset® AH-160
FL6332
Elastoflex G TU, Elastoflex S6 G, Polyflex G, Polyflex SAP, Polyflex SA Cap FR,
Mule -Hide SA-APP Cap Sheet or Mule -Hide SA-APP Cap Sheet (FR)
j
Polystick TU P, Polystick TU Plus, Polystick TU Max, Polystick Tile Pro,
CP Adhesives Polyset® RTA-1
FL6276
Elastoflex G TU, Elastoflex S6 G, Polyflex G, Polyflex SAP, Polyflex SA Cap FR,
I;
I
I Mule -Hide SA-APP Cap Sheet or Mule -Hide SA-APP Cap Sheet (FR)
to Tile Manufacturer's or Adhesive Manufacturer's Florida Product Approval for Overturning Moment Resistance Performance.
ETC, LLC. Evaluation Report P12060.02.09-R24
to of Authorization N32455 6t" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 5 of 14
.1
WNEMOletc.
Allowable Substrates:
Polystick (all variations), Dual Pro, Tile Pro, Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet
(FR) self -adhered to:
➢ New untreated plywood; ASTM D41 primed new untreated plywood; Existing plywood; ASTM D41 primed existing
plywood; New or existing, unprimed OSB; ASTM D41 primed OSB; Southern Yellow Pine; ASTM D41 primed
Southern Yellow Pine; ASTM D41 primed structural concrete; Huber Engineered Woods "ZIP System" Panels
(designed and installed to meet wind loads for project).
Note: Polyglass does not require priming of new or existing plywood or OSB sheathing. New or existing plywood or
OSB sheathing should be cleaned of all dirt and debris prior to application of Polystick membranes.
Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR in hot asphalt to:
➢ ASTM D41 primed structural concrete.
Polyflex G or Polyflex G FR torch -applied to:
➢ ASTM D41 primed structural concrete.
Bond -to -Insulation:
Polystick (all variations), Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) self -adhered
to:
➢ ASTM C1289, Type II, Class 1 polyisocyanurate or Type V polyisocyanurate-composite insulation; Dens Deck
DuraGuard; Dens Deck Prime; or SECUROCK Gypsum -Fiber Roof Board.
Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR in hot asphalt to:
➢ Dens Deck Prime or SECUROCK Gypsum -Fiber Roof Board.
Polyflex G or Polyflex G FR torch -applied to:
➢ ASTM D41 primed structural concrete; Dens Deck Prime or SECUROCK Gypsum -Fiber Roof Board.
For installation under mechanically attached prepared roof coverings, insulation shall be attached per minimum
requirements of the prepared roof covering manufacturer's Product Approval. For installations under foam -on tile
systems, insulation attachment shall be designed by a qualified design professional and installed based on testing of
the insulation/underlayment system in accordance with FBC Section 1504.3.1.
.3 Bond to Mechanically Attached Base Laver:
Polystick (all variations), Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) Dual Pro or
Tile Pro self -adhered to:
➢ ASTM D226, Type I or II felt; Elastobase; Elastobase P or Mule -Hide Nail Base.
Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR in hot asphalt to:
➢ ASTM D226, Type I or II felt; Elastobase; Elastobase P, Mule -Hide Nail Base or Polyglass G2 Base.
Polyflex G or Polyflex G FR torch -applied to:
➢ Elastobase; Elastobase P, Mule -Hide Nail Base, Polyglass G2 Base or Polyglass APP Base.
For installations under mechanically attached prepared roof coverings, base layer shall be attached per minimum
codified requirements. For installations under foam -on tile systems, base layer shall be attached per minimum
requirements of FRSA/TRI April 2012 (04-12), Appendix A, Table 1, or as listed in Section 5.6.4 herein, or as tested in
accordance with FBC Section 1504.3.1.
ETC, U.C. Evaluation Report P12060.02.09-R24
to of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-1128
Polyglass Roof Underlayments; (04) 233-1230 Revision 24: 01/24/2018
Page 6 of 14
ONEMOletc.
.4.2 For mechanically attached Base Sheet, the maximum design pressure for the selected assembly shall meet or exceed
that required under FRSA/TRI April 2012 (04-12), Appendix A, Table 1A.
Alternatively, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1 design
pressure determined in accordance with FBC 1609. In this case, Zones 2 and 3 shall employ an attachment density
designed by a qualified design professional to resist the elevated pressure criteria. Commonly used methods are
ANSI/SPRI WD1, FM Loss Prevention Data Sheet 1-29 and Roofing Application Standard RAS 117. Assemblies marked
with an asterisk* carry the limitations set forth in Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (January
2016) for Zone 2/3 enhancements.
-> !7 Ex osure Limitations:
Elastobase, Elastobase P, Polyglass G2 Base or Polyglass APP Base shall not be left exposed for longer than 30-days
after installation.
Polystick IR-Xe or Polystick MU-X shall not be left exposed for longer than 90-days after installation.
P.O vstic MILS, MTfS PLUS, TiU P. TiU P. us, TLU Max, OUaliPro�TiilelPr,o or Elastofl-,,aQkTLIBrhall n llblleft exp ededifor,
Polyflex SAP or SAP FR, or Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) does not have an exposure
limitation, unless the prepared roof covering is to be adhesive -set tile, in which case the maximum exposure is 30
days.
Elastoflex S6 G or Elastoflex S6 G FR or Polyflex G or Polyflex G FR does not have an exposure limitation, unless the
prepared roof covering is to be adhesive -set tile (Elastoflex S6 G or Polyflex G only), in which case the maximum
exposure is 180 days.
Polystick MU-X has been found through comparative testing to have a lesser coefficient of friction than ASTM D226
roofing felt in a dry condition, tested at standard laboratory conditions. Agreement between purchaser and seller, as
set forth in Section 4.3, Note 1 of ASTM D1970-15, should be established as to slip resistance.
Tile Slippage Limitations (FRSA/TRI April 2012 (04-12)1:
When loading roof tiles on the underlayment in direct -deck the assemblies, the maximum roof slope shall be as
follows. These slope limitations can only be exceeded by using battens during loading of the roof tiles.
TABLE 2: TILE SLIPPAGE LIMITATIONS FOR DIRECT -DECK TILE INSTALLATIONS'
J nderlayment
Tile Profile
Staging Method
Maximum Slope
lastoflex G TU
it
Flat
10-tile stack
7:12
Lugged
8-tile stack (6 over 2)
6:12
lastoflex S6 G or S6 G FR
Flat or Lugged
6-tile stack (4 over 2)
4:12
olystick MTS or MTS PLUS
Flat
6-tile stack (4 over 2)
5:12
Lugged
6-tile stack (4 over 2)
4:12
olystick Tile Pro
Flat or Lugged
6-tile stack (4 over 2)
7:12
� olystick TU Max
Flat
6-tile stack (4 over 2) or 10-tile stack
7:12
Lugged
6-tile stack (4 over 2)
7:12
Lu a
10-ti a star
612
it
olystick TU P
Flat
6-tile stack (4 over 2)
6:12
Lugged
6-tile stack (4 over 2)
4:12
I
olystick TU Plus
Flat or Lugged
6-tile stack (4 over 2)
7:12
Flat or Lugged
10-tile stack
6:12
Polyflex G or G FR
Flat or Lugged
6-tile stack (4 over 2)
4:12
Polyflex SA P or SA P FR
Flat or Lugged
6-tile stack (4 over 2)
4:12
ETC, I.I.C. Evaluation Report P12060.02.09-R24
to of Authorization #32455 6P EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-1128
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 11 of 14
6.
N
ONEMOletc.
INSTALLATION:
1 Polyglass Roof Underlayments shall be installed in accordance with Polyglass published installation requirements
subject to the Limitations set forth in Section 5 herein and the specifics noted below.
.2 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove
any dust and debris prior to application, and prime the substrate (if applicable).
Elasstobase - astobase P or'Mule Hide Nail Base
3.1 Non -Tile Applications:
Shall be installed in compliance with the codified requirements for ASTM D226, Type II underlayment in FBC Table
1507.1.1 for the type of prepared roof covering to be installed.
Elastobase, Elastobase P or Mule -Hide Nail Base may be covered with a layer of Polystick, Polyflex SAP, Polyflex SA
P FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR), self -adhered, Elastoflex G TU, Elastoflex S6 G or
ii Elastoflex S6 G FR in hot asphalt or Polyflex G or Polyflex G FR, torch applied. Roof cover limitations are those are
those associated with the top -layer underlayment, as set forth in Table 1.
.3.2 Tile Applications:
Elastobase, Elastobase P or Mule -Hide Nail Base are limited to use as a mechanically attached base sheet in the "Two
Ply System" from FRSA/TRI April 2012 (04-12). Reference is made to Table 1 and Section 5.6.4 herein, coupled with
FRSA/TRI April 2012 (04-12) Installation Manual.
Po tr - TS; MTSP.LUS, IR=Xe, TU P, TU Plus TU Max Dual Pro, Tile Pr`o or MU=)( or, Polyflex SAP, Polyflex SAP` FR;
- . ide.SA-APP,Cap'Sheet or Mule -Hide SA=AP ap Sheet (FR):,
.4.1 Shall be installed in compliance with the codified requirements for ASTM D1970 (except Polystick TU P) underlayment
in FBC Table 1507.1.1 for the type of prepared roof covering to be installed.
5.4.2 Direct -to -Deck with Mechanically Fastened Roof Covers:
All self -adhering materials, with the exception of Polystick TU Plus, Polyflex SAP or SAP FR and Mule -Hide SA-APP
I, Cap Sheet or SA-APP Cap Sheet (FR) , Quid be back -nailed in selva e e e seam in accordance wit Po ass Mu e-
lameter meta I rd Is RUE Im 13 1 ex- a meta I eap nai , at a minimum rate o 1 o.c. Polystick TU Plus should be back -
nailed using the above noted fasteners and spacing, in area marked "nail area, area para clavar" on the face of
membrane. The head lap membrane is to cover the area being back -nailed.
All seal -lap seams (selvage laps) must be
firmly rolled with a minimum 28 lb. hand
roller to ensure full contact and adhesion.
For Dual Pro and Tile Pro, align the edge of
the top sheet to the end of the glue pattern
(the sheet will overlap the fabric).
View of Ovelap Seam of Dual Pro and Tile Pro
All over -fabric and over -granule end -laps shall have a 6-inch wide, uniform layer of Polyplus 50 Premium Modified
Wet/Dry Cement or Polyglass PG500 Modified Cement applied in between the application of the lap.
Polystick TU Plus, Dual Pro and Tile Pro may not be used in any exposed application such as crickets, exposed valleys,
or exposed roof to wall details
ETC, LLC. Evaluation Report P12060.02.09-R24
to of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-RZ8
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 12 of 14
ONEMOjetc.
Repair of Polystick membranes is to be accomplished by applying Polyplus 50 Premium Modified Wet/Dry Cement or
Polyglass PG500 Modified Cement to the area in need of repair, followed by a minimum 6 x 6 inch patch of the
Polystick material of like kind, set and hand rolled in place over the repair area. Patch laps, if needed, shall be
installed in a water shedding manner.
All Polystick membranes shall be installed to ensure full contact with approved substrates. Polyglass requires a
minimum of 40-lb weighted -roller or, on steep slopes, use of a stiff broom with approximately 40-lbs of load applied
for the field membrane. Hand rollers are acceptable for rolling of patches, laps (min. 28 lb roller) or small areas of the
roof that are not accessible to a large roller or broom.
3.4.j Tile ADDlications (not allowed for Polystick Dual Pro, IR-Xe or Polystick Mu-X):
Reference is made to FRSA/TRI April 2012 (04-12) Installation Manual and Table 1 herein, using the instructions
noted above as a guideline.
For mechanically fastened tile roofing over 2-ply system, consisting of Base Sheet and self -adhering top sheet(s), Base
Sheet fastening shall be not less than FRSA/TRI April 2012,(04-12), Table 1.
For adhesive -set the applications, refer to Section 5.6.4 herein.
.4.4 Two (2) Ply Underlayment Systems:
Polystick MTS or MTS PLUS followed by Polystick MTS, MTS PLUS, TU P, TU Plus, TU Max, Tile Pro, MU-X or Polyflex
SAP is allowable for use under mechanically attached prepared roof systems. Limits of use are those associated with
the top -layer material. This is not a requirement, but is allowable if a 2-ply underlayment system is desired.
Polystick MTS or MTS PLUS followed by Polystick TU P, TU Plus, TU Max, Tile Pro or Polyflex SAP is allowable for use
under foam -on tile systems. Limits of use are those associated with the top -layer material. This is not a requirement,
but is allowable if a 2-ply underlayment system is desired.
i.5 .Elastoflex.G TU, Elastoflex,S6"G or Elastoflex S6 G FR:
.5.1 Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR shall be installed in compliance with current Polyglass published
installation requirements. For use in tile applications:
✓ Elastoflex G TU is for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single
11 Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems or the Hot Asphalt
applied "Cap Sheet" in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened or
adhered tile roof systems.
✓ Elastoflex S6 G is for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single Ply
System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened the roof systems or the Hot Asphalt
applied "Cap Sheet' in the "Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened or
adhered tile roof systems.
✓ Elastoflex S6 G FR is for use as an alternate to "Mineral Surface Roll Roofing" (ASTM D6380, Class M) in the "Single
Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile roof systems or the Hot Asphalt
applied "Cap Sheet' in the `Two Ply System" from FRSA/TRI April 2012 (04-12) beneath mechanically fastened tile
roof systems.
6.5.2 For hot -asphalt -applications, Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR shall be fully asphalt -applied to the
substrates noted in Section 5.6. Side laps shall be minimum 3-inch and end -laps minimum 6-inch wide, off -set
minimum 3 feet from course to course. Side and end laps shall be fully adhered in a complete mopping of hot asphalt
with asphalt extending approximately 3/8-inch beyond the lap edge.
6 6 Polyflex G or,;Polyflex G FR
6.6.1 Polyflex G or Polyflex G FR shall be installed in compliance with current Polyglass published installation requirements.
For use in the applications:
✓ Polyflex G is for use as an alternate to the Heat Applied "Cap Sheet' in the 'Two Ply System" from FRSA/TRI April
2022 (04-12) beneath mechanically fastened or adhered tile roof systems (Base Sheet Limited per 5.6.3).
✓ Polyflex G FR is for use as an alternate to the Heat Applied "Cap Sheet' in the 'Two Ply System" -from FRSA/TRI
April 2012 (04-12) beneath mechanically fastened tile roof systems (Base Sheet Limited per 5.6.3).
ETC, LLC. Evaluation Report P12060.02.09-1124
to of Authorization #32455 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 13 of 14
I
ONEMOjetc.
.6.2 Polyflex G or Polyflex G FR shall be fully torch -applied to the substrates noted in Section 5.6. Side laps shall be
minimum 3-inch and end -laps minimum 6-inch wide, off -set minimum 3 feet from course to course. Side and end
laps shall be fully heat -welded and inspected to ensure minimum 3/8-inch flow of modified compound beyond the lap
edge.
�117 Tile Staging:
11.
7.1 Tile shall be loaded and staged in a manner that prevents tile slippage and/or damage to the underlayment. Refer to
Table 2 herein, and Polyglass published requirements for tile staging.
(117.2 Battens and/or Counter -battens, as required by the tile manufacturer and FRSA/TRI April 2012 (04-12) must be used
on all roof slopes greater than 7:12. Precautions should be taken as needed, such as the use of battens or nail -
boards, to prevent tile sliding and/or damage to the underlayment during the loading process.
.7.3 Polyglass specifies the minimum cure time after installation of self -adhering membranes and before loading of
roofing tiles is forty-eight (48) hours.
i
7. 1 WILDING PERMIT REQUIREMENTS:
is required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of this product.
8. ANUFACTURING PLANTS:
II
!ontact the noted QA agency for information on product locations covered for F.A.C. 61G20-3 QA requirements. The following
slants have qualified products under their respective physical properties specifications.
Plant
5becificatiorr_
Products .
111'ernley, NV, Hazleton, PA & Winter Haven, FL
ASTM D1970
Polystick MU-X
I!Hazleton, PA
M-D 13-0004
Elastoflex G TU
II
Hazleton, PA & Winter Haven, FL
ASTM D1970
Polystick IR-Xe
ASTM D1970 & FRSA/TRI April 2012
Polystick TU Plus
ASTM D1970 & FRSA/TRI April 2012
Polystick TU Max
IiTuscaloosa, AL
ASTM D4601, Type II
Polyglass G2 Base
Winter Haven, FL
ASTM D226 (physicals)
Elastobase, Elastobase P
ASTM D6509
Polyglass APP Base
FRSA/TRI April 2012
Polystick MTS, Polystick MTS PLUS
FRSA/TRI April 2012
Polystick TU P
FRSA/TRI April 2012
Polyflex SAP, Polyflex SA P FR
ASTM D1970
Polystick Dual Pro
ASTM D1970 & FRSA/TRI April 2012
Polystick Tile Pro
ASTM D6164
Elastoflex S6, Elastoflex S6 G FR
ASTM D6222
Polyflex G, Polyflex G FR
9. hUALITY ASSURANCE ENTITY:
L, LLC—QUA9625; (314) 578-3406; k.chancellor@us.ul.com
- END OF EVALUATION REPORT -
ETC, U.C. Evaluation Report P12060.02.09-R24
,te of Authorization #32455 6r" EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 14 of 14