The URL can be used to link to this page

Home My WebLink AboutNOA ALUMINUM SHUTTERSH I M IAM I•DADE TOO� t UILDING CODE COMPLIANCE OFFICE (BCCO) PRODUCT CONTROL DIVISION JOTICE OF ACCEPTANCE I t Awning Co., Inc. NW 36 h Avenue oi. FL D147 MIAMI-DADE COUNTY, FLORIDA METRO-DADE FLAGLER BUILDING 140 WEST FLAGLER STREET, SUITE 1603 MIAMI, FLORIDA 33130-1563 (305) 375-2901 FAX (305) 375-2908 www.miamidade.gov is NOA is being issued under the applicable rules and regulations governing the use of construction materials. e documentation submitted has been reviewed _by Miami -Dade County Product Control Division and accepted the Board of Rules and Appeals (BORA) to be used in Miami Dade County and other areas where allowed by Authority Having Jurisdiction (AHJ). is NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control vision (In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to ve this product or material tested for quality assurance purposes. df this product or material fails to perform in accepted manner, the manufacturer will incur the expense of such testing and the AHJ may immediately coke, modify, or suspend the use of such product or material within their jurisdiction. BORA reserves the right revoke this acceptance, if it is determined by Miami -Dade County Product Control Division that this product or iterial fails to meet the requirements of the applicable building code. pis product is approved as described herein, and has been designed to comply with the High Velocity Hurricane ,ne of the Florida Building Code. (DESCRIPTION: Aluminum Bahama Shutter APPROVAL DOCUMENT: Drawing No. 05-344, titled "Bahama Shutter", sheets 1 through 3 of 3, prepared by Thornton-Tomasetti Group, dated June 28, 2005, last revision 92 dated June 28, 2006, signed and sealed by V.J. Knezevich, P.E., bearing the Miami -Dade County Product Control Revision stamp with the Notice of Acceptance number and expiration date by the Miami -Dade County Product Control Division. MISSILE IMPACT RATING: Large and Small Missile Impact LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and the following statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein. RENEWAL of this NOA shall be considered after a renewal application has been filed and there has been no change in the applicable building code negatively affecting the performance of this product. TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product, for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section of this NOA shall be cause for termination and removal of NOA. ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done in its entirety. INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and shall be available for inspection at the job site at the request of the Building Official. This NOA revises NOA # 05-0718.04 and consists of this page 1, evidence submitted pages E-1, E-2, & E-3 as well as approval document mentioned above. The submitted documentation was reviewed by Helmy A. Makar, P.E., M.S. ye�wAc� NOA No 06-0711.08 Expiration Date: 02/27/2011 ini Approval Date: 04/05/2007 04- 05-Aco% Page 1 Hurst Awning Co., Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 1. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL # 95-0113.02 A. DRAWINGS - 1. Drawing No. 94-187, "Bahama Shutter", Sheets I and 2 of 2, prepared by Knezevich and Associates, Inc., dated 11129194, rev. #2 dated 01123195, signed and sealed by V.J. Knezevich, P.E. 2. Die Drawing No. GAS-42150 of extruded louver blade. B. TESTS -Testreport on Large Missile Impact Test and Cyclic Wind Pressure Test of Bahama shutters, prepared by Hurricane Engineering & Testing, Inc., Report No.HETI-94-377, dated Nov. 17, 1994, signed and sealed by Hector M. Medina, P.E. 2. Test report on Uniform Static Air Pressure Test of bahama shutters, prepared by Hurricane Engineering & Testing, Inc., Report No. HETI-94-373, dated Nov. 15, 1994, signed and sealed by Hector M. Medina, P.E. C. CALCULATIONS 1. Anchor analysis and calculations dated 01106195, Pages 1 thru 4 of 4, prepared by Knezevich and Associates, Inc., signed and sealed by V.J. Knezevich, P. E. D. MATERIAL CERTIFICATIONS L Mill Certified Inspection Report issued by INDALEX dated Dec. 13, 1994 with chemical composition and physical properties of alum. alloy 6063-T6 for louver blade Part No. GAS-42150. 2. Certified Tensile Test Report No. HETI 94-T45, for colonial and bahama shutter specimen, prepared by Hurricane Engineering & Testing, Inc., dated 11129194, per ASTME8-93, signed and sealed by Hector M. Medina, P.E. 2. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL # 98-0213.06 A. DRAWINGS 1. Drawing No. 94-187, "Bahama Shutter", Sheets 1 and 2 of 2, prepared by Knezevich and Associates, Inc., dated 11 /29/94, rev. #4 dated 02/20/98, signed and sealed by V.J. Knezevich, P.E. B. CALCULATIONS 1. Anchor analysis and calculations dated 02/10/98, Pages 1 thru 4 of 4, prepared by • Knezevich and Associates, Inc., signed and sealed by V.J. Knezevich, P.E. v Imy A. Makar, P.E., M.S. Product Control Examiner NOA No 06-0711.08 Expiration Date: 02/27/2011 Approval Date: 04/05/2007 E-1 Hurst Awning Co., Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED 3. EVIDENCE- SUBMITTED UNDER PREVIOUS APPROVAL # 01-0301.01 A. DRAWINGS 1. None. B. TESTS 1. None. C. CALCULATIONS 1.. None. D. MATERIAL CERTIFICATIONS 1. None. 4. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL # 01-0312.06 A. DRAWINGS 1. Drawing No. 00-351, titled " Bahama Shutter ", prepared by Knezevich & Associates, Inc., dated January 19, 2001, last revision #1 dated November 20, 2001, sheets 1 through 3 of 3, signed and sealed by V.J. Knezevich, P.E. B. TESTS 1. None. C. CALCULATIONS 1. None. D. MATERIAL CERTIFICATIONS 1. None. 5. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL # 02-0315.01 A. DRAWINGS See NOA 02-0315.01 (General Notes) B. TESTS See NOA 01-0312.06 C. CALCULATIONS See NOA 01-0312.06 D. MATERIAL CERTIFICATIONS See NOA 01-0312.06 E. STATEMENTS See NOA 01-0312.06 my A. Makar, P.E., M.S. Product Control Examiner NOA No 06-0711.08 Expiration Date: 02/27/2011 Approval Date: 04/05/2007 E-2 Hurst Awning Co., Inc. NOTICE OF ACCEPTANCE: EVIDENCE SUBMITTED F. OTHER See NOA 01-0312.06 6. EVIDENCE SUBMITTED UNDER PREVIOUS APPROVAL # 05-0718.04 A. DRAWINGS 1. Drawing No. 05-344, titled "Bahama Shutter ", sheets 1 through 3 of 3, prepared by Thornton-Tomasetti Group, dated June 28, 2005, last revision #1 dated April 04, 2006, signed and sealed by V.J. Knezevich, P.E. B. TESTS 1. None. C. CALCULATIONS 1. Anchor analysis and calculations, dated June 17, 2005, 10 Pages, prepared by Thornton-Tomasetti Group, signed and sealed by V.J. Knezevich, P.E. D. QUALITY ASSURANCE 1. By Miami -Dade County Building Code Compliance Office. E. MATERIAL CERTIFICATIONS 1. None. 7. NEW EVIDENCE SUBMITTED A. DRAWINGS 1. Drawing No. 05-344, titled "Bahama Shutter", sheets 1 through 3 of 3, prepared by Thornton-Tomasetti Group, dated June 28, 2005, last revision 92 dated June 28, 2006, signed and sealed by V.J. Knezevich, P.E. B. TESTS 1. None. C. CALCULATIONS 1. None. D. QUALITY ASSURANCE L By Miami -Dade County Building Code Compliance Office. E. MATERIAL CERTIFICATIONS 1. None. my A. Makar, P.E., M.S.- Product Control Examiner NOA No 06-0711.08 Expiration Date: 02/27/2011 Approval Date: 04/05/2007 E-3