HomeMy WebLinkAboutNOAI `v, MIAMI-DADE COUNTY
1� PRODUCT CONTROL SECTION
DEP IRTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER) 11805 SW 26 Street, Room 208
BOAT D AND CODE ADMINISTRATION DIVISION Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
NOjjFICE OF ACCEPTANCE (NOA) www.miamidade.gov/economy
GA�J
1 Ca"mpus Drive
Pars�ipanny, NJ 07054��
Sc PE:
This'�NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
doc mentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
use �; in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This'NOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In iami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
mangler, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
sus end the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
req irements of the applicable building code.
Thil product is approved as described herein, and has been designed to comply with the Florida Building Code
incl4ading the High Velocity Hurricane Zone of the Florida Building Code.
DESCRIPTION: GAF Leak Barriers and Roof Deck Protection
LAPELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
stathnent: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RE EWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in tl,le applicable building code negatively affecting the performance of this product.
TE MINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
gnat rials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for ales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
Of t its NOA shall be cause for termination and removal of NOA.
ADI ERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
exp (ration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in i�s entirety.
1N PECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
sha be available for inspection at the job site at the request of the Building Official.
Thi' NOA renews and revises NOA 16-1213.04 and consists of pages I through 10.
The submitted documentation was reviewed by Hamley Pacheco, P.E.
NOA No.: 18-0119.15
MIAM143ADECAUNTY Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 1 of 10
ROOFING COMPONENT APPROVAL
Cate for : Roofing
Sub- it ategory: Underlayment
Material: SBS/Polypropylene/Asphalt
PRO1DUCTS DESCRIPTION:
Test
Product
Product
Dimensions
Specification
Description
WeatherWatch"
Mineral
36" x 50' rolls
ASTM D 1970
Granular surfaced modified, fiberglass reinforced,
Surf,
ced Leak Barrier
36" x 66.7' rolls
bituminous sheet material for use as a leak barrier
Manufacturing
underlayment in sloped roof assemblies.
Locai
ion #1, 9
Designed as an ice & rain shield.
Stor
Guard' Film
36" x 66.7' rolls
ASTM D 1970
Modified, fiberglass reinforced, bituminous sheet
Surfaced
Leak Barrier
material for use as a high temperature leak barrier
Manufacturing
underlayment in sloped roof assemblies.
Loca{ion
#1, 9
Designed as an ice & rain shield.
LibelltyTM SBS Self-
39 3/s" x 66' rolls
ASTM D 1970
Self -adhering SBS roof membrane.
Adhering Base/Ply Sheet
ASTM D4601
Mani
acturing
Type II
Locaion #1, 9
Dec Armor"' Premium 54" x 222' rolls
Breathable Roof Deck 48" x 100' rolls
Locd' ion #2
TigerPawT"' Roof Deck
48" x 250' rolls
Protction
48" x 100' rolls
Mani.ifacturing
Locdtion #3, 5, 6
FeltBl uster" High -Traction
48" x 250' rolls
Synthetic Roofing Felt
Manufacturing
Loc ;ton #7, 8
Shingle -Mate" Roof Deck
36" x 144' rolls
Protection
#4
ASTM D 226 A UV -stabilized polypropylene breathable
Type II underlayment. To be used for roof deck
protection as an underlayment in sloped roof
assemblies.
ASTM D 226 A UV -stabilized polypropylene non -breathable
Type II underlayment. To be used for roof deck protection
as an underlayment in sloped roof assemblies.
ASTM D 226 A UV -stabilized polypropylene non -breathable
Type I - underlayment. To be used for roof deck protection
as an underlayment in sloped roof assemblies.
ASTM D 226 Fibergass-reinforced asphalt felt underlayment. To
Type I be used for roof deck protection as an
underlayment in sloped roof assemblies.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 2 of 10
PRO
bUCTs DESCRIPTION:
Test
Product
Product
Dimensions
Specification
Description
Libe
. Tm SA Glass Cap
39 3/s" x 34' rolls
ASTM D 1970
Granular surfaced modified, fiberglass reinforced,
Sheet
ASTM D 6163
self -adhering SBS roof membrane.
Mani
acturing
ASTM D 7530
Loca, �'on # 9
GAIT LAS@ Ply 4
39.37"
ASTM D2178
Aspahalt impregnated glass felt with aspahlt
Mail' cturing
(1 meter) Wide
Type IV
coating.
Location # 9, 10
GAF'GLAS® FlexP1yTM 6
39.37"
ASTM D2178
Aspahalt impregnated glass felt with aspalilt
Manufacturing
(1 meter) Wide
Type VI
coating.
,*on # 9, 10
vUFACTURING LOCATION:
.Mt. Vernon, IN
.North Bay, Ontario
.Mission, British Columbia
.Pryor, OK
.Qingdao, China
.Charleston, SC
.Spartanburg, SC
.Dadra, India
.Savannah, GA
O.Mobile, AL
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 3 of 10
PRI
Tech,
ENCE SUBMITTED:
Test Agency
k Testing Services NA Ltd.
G�;onstruction Materials
uologies, LLC.
-ERD
Test Identifier
Test Name/Report
Date
3077464-01
ASTM D 1970
08/23/06
3090131
Wind Uplift and Self Sealability
08/23/06
100258583COQ-OIOA
ASTM D 226 Type II
01/08/11
100673818COQ-003
ASTM D 226 Type II
06/13/13
10 1 57289000Q-005
ASTM D 226 Type 11
04/17/14
F8549.02-106-18
ASTM D 226 Type I
11/08/16
RGM-023-02-01
ASTM D 4798
05/16/07
GAF-1 12-02-01
ASTM D 226 Type II
03/15/06
GAF-238-02-01
ASTM D 1970
03/03/10
GAF-323-02-01
ASTM D 1970
11/30/11
GAF-324-02-01
ASTM D 1970
12/01/11
GAF-325-02-01
ASTM D 1970
12/01/11
GAF-326-02-01
ASTM D 1970
11/30/11
GAF-275-02-01
ASTM D 1970
11/11/10
GAF-344-02-01
ASTM D 1970
04/23/12
GAF-339-02-01
ASTM D 226 Type I
03/14/12
ELK-311-02-01
ASTM D 1970 .
09/11/07
GAF-518-02-01
ASTM D 226 Type I
06/04/14
GAF-818-02-01
ASTM D 4533
12/06/17
GAF-829-02-01
ASTM D 226 Type II
01/15/18
GAF-314-02-01
ASTM D 2178
07/21/11
GAF-315-02-01
ASTM D 2178
07/2,1/11
GAF-SC13285.03.17-1
ASTM D 1970
03/08/17
GAF-SC13285.03.17-3
ASTM D 1970
03/01/17
GAF-SC13285.03.17-4
ASTM D 1970
03/01/17
GAF-SC13285.02.17-2
ASTM D 4601 Type II
02/08/17
GAF-SC9700.08-15-RI
ASTM D 2178
09/09/15
GAF-SC12915.12.17-RI
ASTM D 1970
12/11/17
GAF-SC12915.12.17-RI
ASTM D 6163
12/11/17
GAF-SC12915.12.17-R1
ASTM D 7530
12/11/17
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 4 of 10
AP OVED ASSEMBLIES:
Deck Type 1: Wood, non -insulated
Dec Description: '9/32" or greater plywood or wood plank
System E (1): Anchor sheet mechanically fastened to deck, membrane adhered.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle -Mate' Roof Deck Protection OR one or more plies
of ASTM D 226 Type II, Deck-ArmorTm Premium Breathable Roof Deck Protection, FeltBuster°
High -Traction Synthetic Roofing Felt, or Tiger Paw' Roof Deck Protection with a minimum 4"
side lap and a 6" end lap mechanically fastened to the deck with approved nails and tin caps 6"
o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape (follow the tape's manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
brane: One or more plies of WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film
Surfaced Leak Barrier, LibertyTM SA Glass Cap Sheet, or LibertyTM SBS Self -Adhering
Base/Ply Sheet membrane with a minimum 3" side lap and 6" end lap. Place the first course of
membrane parallel to the eave, rolling the membrane to obtain maximum contact. Remove the
release membrane as the membrane is applied. Vertical strapping of the roof with
WeatherWatch' Mineral Surfaced Leak Barrier, or StormGuard® Film Surfaced Leak Barrier is
acceptable.
cing: Approved Roofing Assembly.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 5 of 10
Dec Type 1: Wood, non -insulated
Dec Description: "62" or greater plywood or wood plank
Syst Im E(2): Membrane mechanically fastened to deck.
Sep rator Sheet: One or more plies of GAFGLAS° Ply 4, GAFGLAS° FlexPlyTM 6, Shingle -Mateo Roof Deck
Protection, Deck -Armor TM Premium Breathable Roof Deck Protection, FeltBuster° High -
Traction Synthetic Roofing Felt, or Tiger PawTM Roof Deck Protection loose laid.
Membrane: One or more plies of WeatherWatch' Mineral Surfaced Leak Barrier, StormGuard® Film
Surfaced Leak Barrier, LibertyTM SA Glass Cap Sheet, or LibertyTM SBS Self -Adhering
Base/Ply Sheet membrane mechanically fastened with a minimum 3" side lap and a 6" end lap to
deck through the separator sheet with approved nails and tin caps 6" o.c. at the laps and two
staggered rows 12" o.c. in the field of the roll.
Sur Acing: Approved Roofing Assembly.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 6 of 10
Type 1: Wood, non -insulated
Description: 19/32" or greater plywood or wood plank
E (3): Anchor sheet mechanically fastened to deck, membrane adhered.
See hdary Water
Bar �Iier:
(Optional)
Sheet:
Install a minimum 4" wide WeatherWatch® Mineral Surfaced Leak Barrier, , LibertyTM SBS
Self -Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, or StormGuard® Film Surfaced
Leak Barrier membrane over the joints of the plywood roof deck prior to installation of the base
sheet. Do not overlap end or side joints. All side and end laps should be butted firmly side by
side, flush with each other but not overlapped. Do not leave the WeatherWatch® Mineral
Surfaced Leak Barrier, or StormGuard® Film Surfaced Leak Barrier membrane exposed for more
than 30 days without a roof deck protection underlayment protecting the secondary water barrier.
Two plies of ASTM D 226 Type I or Shingle -Mate Roof Deck Protection OR one or more plies
of ASTM D 226 Type Il, Deck -Armor TM Premium Breathable Roof Deck Protection,
FeltBusterg' High -Traction Synthetic Roofing Felt, or Tiger PawTM Roof Deck Protection with a
minimum 4" side lap and a 6" end lap mechanically fastened to the deck with approved nails and
tin caps 6" o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape (follow the tape manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fasteners.
Approved Roofing Assembly.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 7 of 10
De
Sy
Ba
Type 1: Wood, non -insulated
Description: 19/32" or greater plywood or wood plank
m E (4): Anchor sheet mechanically fastened to deck, membrane adhered.
Sheet: Two plies of ASTM D 226 Type I or Shingle -Mate® Roof Deck Protection OR one or more plies
of ASTM D 226 Type II, Deck-Armoi" Premium Breathable Roof Deck Protection,
FeltBuster® High -Traction Synthetic Roofing Felt, or Tiger Paw' Roof Deck Protection with a
minimum 4" side lap and a 6" end lap mechanically fastened to the deck with approved nails and
tin caps'6" o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape (follow the tape's manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
brane: One or more plies of StormGuard® Film Surfaced Leak Barrier membrane with a minimum 4"
side lap and 6" end lap. Place the first course of membrane parallel to the eave, rolling the
membrane to obtain maximum contact. Remove the release membrane as the membrane is
applied.
.cing: Approved for Metal roofing, Slate, and Asphalt Shingle assemblies.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 8 of 10
LIMITATIONS:
C
1. Fire classification is not part of this acceptance.
2. eatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-ArmorTM
remium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and tiger PawTM
oof Deck Protection shall not be used as roof tile underlayment.
3. his acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuardo Film Surfaced Leak
arrier, LibertyTM SBS Self -Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck
Protection, Deck-ArmorTM Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic
Roofing, Felt, and Tiger PawTM Roof Deck Protection shall be installed in strict compliance with applicable
Building Code.
4. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self-
,' dhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mateo Roof Deck Protection, Deck-ArmorTM
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection membranes shall be applied to a smooth, clean and dry surface with deck free of
5. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-ArmorTM
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection membranes shall not be applied over an existing roof membrane.
6. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-ArmorTM
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection shall not be left exposed as a temporary roof for longer than 30 days of application.
7. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-ArmorTM
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection may be used with any approved roof covering Notice of Acceptance listing WeatherWatch®
Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -Adhering Base/Ply
Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-ArmorTM Premium Breathable
Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger Paw' Roof Deck Protection
as a component part of an assembly in the Notice of Acceptance. If WeatherWatch® Mineral Surfaced Leak
I arrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -Adhering Base/Ply Sheet, LibertyTM SA
Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-ArmorTM Premium Breathable Roof Deck Protection,
FeltBuster' High -Traction Synthetic Roofing Felt and Tiger PawTM Roof Deck Protection are not listed; a request
may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Department
for approval provided that appropriate documentation is provided to detail compatibility of the products, wind
uplift resistance, and fire testing results.
8'. 1All nails in the deck shall be carefully checked for protruding heads. Re -fasten any loose decking panels. Sweep
the deck thoroughly to remove any dust and debris prior to application. Install when temperatures are 45' F and
9.�,lIWhen applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane
;from the center outward in both directions.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 9 of 10
LI ITATIONS:
10.l loll or broom the entire membrane surface so as to have 100% contact with the surface, giving special attention to
Iverlap areas.
11. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance and applicable Building Code.
12. k1l products listed herein shall have a quality assurance audit- in accordance with the Florida Building Code and
ule 61 G20-3 of the Florida Administrative Code.
13. 1All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo,
(city and state of manufacturing facility, and the following statement: "Miami -Dade County Product Control
jApproved" or the Miami -Dade County Product Control Seal as shown below.
END OF THIS ACCEPTANCE
NOA No.: 18-0119.15
WAMMADB COUNTY.
. • • .. � � Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 10 of 10