HomeMy WebLinkAboutEVALUATION REPORTSCANNED
t. Lucb, Gourd
EXTERIOR RESEARCH & DESIGN, I.I.C.
Certifrcote of Authorization #9503
TRINIY I ERD 353 MRIMN STREET, UNIT813
OXFORD, Cr 06478
EVALUATION REPORT R CE IV E ® ` . (203) 262-9245
Soprerna, Inc. Evaluation Report S1N10.06.094M
1640 rue Haggerty A U G 16 2018 F12569-R13
Drummondville, QuL&bec J2C 5P8 Canada Date of Issuance: 06/15/2009
Sl`. Lucie County, Permitting
(819) 478-2400 Revision 11:10106/2017
SCOPE:
This Evaluation Report is issued under Rule 61620-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted'has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code and Florida Building Code, Residential Volume. The
products described herein have been evaluated for compliance with the 6u' Edition (2017) Florida Building Code
sections noted herein.
DESCRIPTION: Soprema Roof Underlayments
UWEUNG: labeling shall be in_accordance with the requirements the Accredited Quality Assurance Agency noted
CONTINUED CGWUANM This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named, client constitutes agreement to notify Robert Nieminen, P.E. if the product
changes or the referenced Quality Assurance documentation changes. TrinkVI ERD requires a complete review of this
Evaluation Report relative to updated Code requiremeriftwith each Code Cycle.
ADVOMSEME n: The Evaluation Report number preceded by the words "Trinity) ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
iNWEcnoN: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the iob site at the request of the Building Official.
Evaluation Report consists of pages 1 through 8.
pared by:
Jac' 3!- t r--'�•y
j,,00.5 tGF.d7F3 's'
vert J.M. Nieminen• P.E.
•-t: �Q ?� 7lmfaatmseOlariig�sautha¢edbyxobert
daRegistrabonNa391W,FloridaMANW83 iya axa4 ;atiWkftftW RL0010300M7.iiftclmnasemasan
rQhrnnia�P - dMhMie1l11�d�Nnd�t
IfeW7tOA1 � iraa
TrinitylERD does not have, nor does it intend to acquire or will It acquire, a financial Interest in any company manufacturing or
distributing products it evatuaws.
Trinityl ERD is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
Robert Nieminen, P.E. does not have nor will acquire, a financial Interest in any company manufacturing or distributing products for
which the evaluation reports are being Issued.
Robert Nieminen, P.E. does' not have, nor will acquire, a financial interest in any other entity involved In the approval process of the
product
This is a building code evaluation. Neither TrinttylERD nor Robert Nieminen, P.E. are, In any way, the Wgner of Record for any
project on which this Evaluation Report; or previous versions thereof. is/was used for penrdtfing or design guidance unless retained
specifically for that mirvose.
COMPONENT EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Underlayment
Compliance Statement: Roof Underfayments, as produced by Soprema, have demonstrated compliance with the
following sections of the 6* Edition (2017) Florida Building Code through testing in accordance with the following
Standards. Compliance is subject to the Installation Requirements and Limitations / Conditions of Use set forth
herein.
2. STANDARDS:
Section
Property
Standard
Year
1504.3.1
Wind Resistance
FM 4474
2011
1504.3.2
Wind Uplift
UL 1897
2012
1507." T1507-L1,1507Z9.2
Physical Properties
ASTM D1970
2015
1SO733
Physical Properties
FRSA/TRI April 2M2
2012
FRSA/TRI April 2022 (04-12)
Physical Properties
ASTM D6163
2W8
TAS 110
Accelerated Weathering
TAS 110
2000
3. REFERENCES:
Entity
Examination
Reference
Date
ERD (TST6049)
ASTM D1970 / TAS 110
296805.04-2
OS/14/2004
ERD CM6049)
Physical Properties
2757.02AS
02103f2WS
ERD (TST6049)
ASrM D1974 / TAS 110
2974.0105-2
05/17/2005
ERD (TST6049)
Wind Resistance
277807.05
07/15/2005
ERD (TST6049)
Wind Resistance
2779.1L05-R1
0411BA007
ERD (TST6049)
TAS 203 / TAS 110
S7120AL07--2
11/02/2007
ERD (iSTW49)
ASTM D1970 / TAS 210
S13190.0209-R1
04/01/2010
ER6 (TST6049)
ASTM D1970/TAS 110
S3137Q0310.1 Rl
04/07/2110
ERD(TST6049)
Physical Properties /Tensile Adhesion
511150A)SI R1
09/09/2010
ERD (TST6049)
Physical Properties /Tensile Adhesion
S11150.05.09-R2
10/0SAM0
ERD (TST6049)
ASrM D1970
S37210ALU
11/09/2013L
ERD (7S'r6049)
ASTM D1970
S40540A2.13-1
02/19/2013
ERD(•TSWAX9)
Physical Properties/ Tensile Adhesion
S43530.0214-1
02/21/2014
ERD(TSM049)
Physical Properties /Tensile Adhesion
SOPC-SC7645.02.15
02/13/2015
ERD (TWM9)
Accelerated Weathering
SOPC-SCO52OL14
04/17/2015
ERD (TST6049)
Wind Resistance
SOPC-SC14045.0517-R1 06/07/2017
M-D (CER1592)
HVHZ Compliance
15-05O804
09/24/2015
ICC ES(EVL2396)
2015IBC Compliance
ESR 1524
03/01/2017
PRI (TST5878)
Physical Properties
SOP-064-02-01
12/03/2013
Sopnema, Inc. (PDM3511)
Equivalency Declaration
SA SMOaM PLY40
06/29/2015
UL, LLC (QUA9625)
Quality Control
Service Confirmation
Exp. 07/18/2020
4. PRODUCT DESCRIPTION:
4.1 LasUftn'd TU HT is a self -adhering, non -woven polyester fabric surfaced, SSS modified bitumen roof
undedayment; meets ASTM D1970 and FRSA/TRI April 2012 (04-12).
4.2 LasWbond Shield
Is, a self adhering, woven polyethylene surfaced, SBS
modified bitumen roof
underiayrrient available in two widths, 36 and 45 inch; meets ASTM D1970.
4.3 RESISTO SA SMOOTH PLY 40 Is a self -adhering, woven polyethylene surfaced, SBS modified bitumen roof
und6dayment; available in 3.3 ft x 65 ft rolls; meets ASTM D1970.
4.4 Lastolmnd Shield HT is a self -adhering, woven polyethylene surfaced, high temperature, SBS modified
bitumen roof underlayment. meets ASTM D3970.
Exterior Research and Design, LLC. Evaluation Report SM10AGAS-ILU
M�JSSQ3 EDMON(2017)FBCNOWWWEVALUATION F125694U3
Soprew, Inc. Revision 11:10/06/;017
Paga2ofa
5.
�7 I�l�TY I ERD
TRI
4.5 Lastobond Pro HT N is a self -adhering, woven polyethylene surfaced, SBS modified bitumen roof
underlayment available in two widths; 36 and 45 inch; meets ASTM D1970.
4.6 Lastobond Pro HT S is a self -adhering, woven polyethylene surfaced, high temperature, SBS modified
bitumen roof underlayment; meets ASTM.D1970.
4.7 Lastobond 195 Is a self -adhering, glass -mat reinforced, sand -surfaced, SBS modified bitumen roof
underlayment; meets ASTM D1970.
4.8 Lastobond: Eaves Protection Sheet is a.seWadhering, glass -mat reinforced, sand -surfaced, SBS modified
bitumen roofunderlayment; meets ASTM U1970.
4.9 - Lastobond..-Eco is a self -adhering, glass -mat' reinforced, sand -surfaced, SBS modified bitumen roof
�-- ndertayment; meets ASTM D1970.
4,11� RESISTO LB1236 is a self -adhering,_ glass=mat reinforced, sand -surfaced, SBS modified bitumen roof
underlayment, with a 36-inch sheetwidth; meets ASTM D1970.
4.12 PrimeSource Grip -Rite Eave & Valley Protector is a self -adhering, glass -mat reinforced, sand -surfaced, SBS
modified bitumen roof underlaymert with a 36-inch sheet width; meets ASTM D1970.
4.13 RESISTO LB1244 is a self -adhering,. glass=mat reinforced, sand -surfaced, SBS -modified bitumen roof
underlayment, with a 44-inch sheet width; meets ASTM D1970.
4.14 Colphene FR GR is a sell -adhering, fiberglass reinforced, granule -surfaced, SBS modified bitumen roof
underlayment;. meets ASTM D1970 and FRSA/TRI April 2012 (04-12).
LIMITATIONS:
5.1 This is a building code evaluation. Neither Trinity IERD nor Robert Nieminen, P.E. are, in any way, the
Designer of Record for any project on'iivhich1his Evaluation Report,.. or. previous versions thereof, is/was
used for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is notfor use in FBC HVHZ jurisdictions.
5.3 Fire Classification is not part of this report;.refer to current Approved Roofing Materials Directory for fire
ratings of this product.
5.4 Soprema Roof Underlayments may: be -Used with any prepared roof cover where the product is specifically
referenced within FBC approval documents':' If not listed, a request.may be made to the Authority Having
Jurisdiction for.approval based on this evaluation combined with supporting data for the prepared roof
covering.
Sty ..- AllowableAoof.Covers:
TAB[F� :RooF COVQt QPTioNS
Underlayntent
Asphalt,`=
Nall -On
Foam -On
Metal
Wood Shakes &
Slate
Shingles;
Tile
Tile
Shingles
Lastobond TU HT
Yes
- .Yes
Yes
Yes
Yes
Yes:
See 5;5:1
Lastobond.Shield / Pro HT N J RESISTO SA?:
SMOOTH PLY40
Yes
Noy
Nog
_; No,
Yes
Yes. '
Lastobond Shield HT/ Pro HT-S
Yes
111px
Nc
. Yes
Yes
Yes
Lastobond Eaves Protection Sheet/
Yes
No�IVo`i
YesYes
Lastobond 195
r
Now Q'
Lastobond ECO / RESISTO m236, Grip
Rte Save &Valley Protector/ RESISTO
Nor
Yes
Yes
Exterior Research and Design, LLC. Evaluation Report 518010.06.09-R11
CffWcafe ofAarharka .n 09S03 6T" EDITION (2017) FBC NON-HVHZ EVALUATION F1.2569 R13
Soprema, Inc Revision 11.10/06/2017
Page 3 of 8
QOTRII IMIIERD -
-
,Frr
Asphak
vail-0n
FUndedaymentoanh-01f
,Tf
Metal
WoodShalkes&'
Slate
Sifte"
f
Shilwes
Lastoboad Smooth Seal HT
Yes
- ,_" n�
'�:-
Yes
_Yes .
Yes
Yes
Colphene FR GR
Yes
Yes.
Yes ,-
�' Yes
See sm .
5-5-1 "Foam -On Tile" is limited to use of following Approved the adhesives / undedayment combinations.
AtIhesile
11CPAdhesivesPolysetGAN-26o
Honda ProdiictApproval
Umicrlayments
Dow ThleBond-
FL22525
Lastobond W Fir
FL6332
Lastobond 1U Hror Colphene Rt GR
5.6 Allowable Substrates:
S.6.1 Direct -Bond to Deck:
Lastobond Shield, LastobOnd Pro HT-N, RESISTO, SA SMOOTH PLY 40, Lastobond Shield HT, Lastobond
Pro HT S, Lastobond TU HT, Lastobond Eaves Protection Sheet, Lastobond 195, LaswWnd ECO, RESISTO
L 82236, Grip -Rite Eave & Valley Protector. RESISTO LB2244 or Lastobond Smooth Seal HT applied to:
➢ Plywood; ASTM D41 primed plywood; 058, ASTM D41 primed OSB; Southern Yellow Pine; ASTM D41
primed Southern Yellow Pine; ASTM D41 primed structural concrete.
Colphene FR GR applied to:
➢ Plywood; ASTM D41 primed plywood, ASTM D41 primed structural concrete.
Note:
➢ While not required over plywood, OSB or Southern Yellow,Pine substrates, Soprema recommends
priming with Elastocol Stick or Elastocol 600c if the final roof cover is not slated for installation within
24 hours.
➢ Soprema requires tongue -and -groove board decking be covered with plywood or OSB prior to
installation of the self -adhering underlayment.
5.6.2 Bond to4nsulation:
Lastobond Shield, Lastobond Pro HT-N, RESlSTO SA SMOOTH PLY 40, Lastobond Shield HT, Lastobond
Pro HT S, Lastobond TU HT, Lastobond Eaves Protection Sheet, Lastobond 295, Lastobond ECO, RESISTO
L81236, Grip4Ute Eave & Valley Protector, RESISTO L81244, Lastobond Smooth Seal HT or Colphene FR
GR applied to:
➢ Dens Deck Prime; SECUROCK Gypsum -Fiber Roof Board.
For installation under mechanically attached prepared roof coverings, insulation shall be attached per
minimum requirements of the prepared roof covering manufacturer's Product Approval. For installations
under foam -on tie systems (Lastobond TU HT only), insulation attachment shall be designed by a qualified
design professional and installed based on testing of the insulation/underlayment system in accordance
with FM 4474, Appendix D, Testing Application Standard TAS 114, Appendix J or UL1807.
2 Refer to Tile Manufacturer's orAdhesive Monufactumes flodda ProdoctApMval for ovwtuming Moment Resistance Perf rmance.
Exterior Research and oes%n, LLG
Qer�lmOeoJAoEhorieotbn6A5� 6'N EraWatlon RepoRSl8tri0: 9
WMCIX (20171 FOC K0*HVIR EVALUATM FLZ58569U3 4R13
Soprhshha, Inc Revisio:111:10/"/2017
Pm4of8
QOTPRJNnYIERD
5.6.3 Bond to Mechanically Attached Base Laver.
Lastobond Shield, Lastobond Pro HT-N, RESISTO SA SMOOTH PLY 40. Lastobond Shield HT, Lastobond Pro
HT S, Lastobond TU HT, Lastobond Eaves Protection Sheet, Lastobond 195;' Lastobond ECO, RESISTO
L61236, Grip -Rite Eave & Valley Protector, RESISTO L61244, Lastobond Smooth Seal HT or Colphene FR GR
applied to:
D ASTM D226, Type I or 11 felt, Sopra-G; Modified Sopra-G.
For installations under mechanically attached prepared roof coverings, -base layer shall be attached per
minimum codified requirements. For installations under foam -on file systems (Lastobond TU HT only),
base layer shall be attached in accordance with FRSA/TRI April 2012 (04-12),
5.6.4 Wind Resistance for Underlayment Systems in Foam -On Tile Applications: FRSA/TRI April 2012 (04-12)
does not address wind uplift resistance of all underlayment systems beneath foam -on tile systems, where
the underlayment forms part of the load -path. The following wind uplift limitations apply to underpayment
systems that are not addressed in FRSA/TRI April 2012 (04-12) and are used in foam -on file applications..
Maximum Design Pressure is the result of testing for wind load resistance based on allowable wind loads,
and reflects the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has
already been applied). Refer to FRSA/TRI Apra( 2012 (04-12) or FBC 1609 for determination of design wind
pressures.
#1 Maximum Design Pressure = -4S.0 osf:
Deck Min. 15/32-inch plywood to meet project requirements to satisfaction of Authority
Having Jurisdiction.
Primer. (Optional) Elastocol Sticky Elastocol 600c or RESiSTO EXTERIOR PRIMER
Underlayment: Lastobond TU HT or Colohene FR GR, self -adhered.
#2 _Maximum Design Pressure = -67S asf•
Deck: Structural concrete to meet project requirements to satisfaction of Authority Having
Jurisdiction.
Primer: Efastocol600c
Underlayment: . Lastobond TU HT or Colphene FR GR, self adhered.
#3 Maximum Design Pressure =-1s0 0 nsf-
neck: Min. 15/32-inch APA-rated SCX plywood (may be installed C-Ade up) to meet project
requirements to satisfaction of Authority HavingJurisdiction.
Deck Preparation: Plywood shall be thoroughly cleaned to remove dust and debris that may inhibit
adhesion. All sheathing fasteners shall be driven flush with the surface. All sharp
splinters and wood projections shall be removed/sanded.
Primer: (Optional) RESISTO EXTERIOR PRIMER
Underlayment: Lastobond TU HT, self -adhered, shall be thoroughly roll using hand roller and/or
weighted roller to ensure there are no voids, and ensure there are no voids/bridging at
side and end -laps.
#4 Maximum Design Pressure = -60 0 asE
Deck., Min. 19/324nch •plywood to meet project requirements to satisfaction of Authority
Having Jurisdiction.
Base Sheet: Sopra-G or Modified Supra-6 mechanically attached with nails (FBC 15175.1) and tin
caps (FBC 15175.2) spaced 6-inch o c. at the 44nch laps and 64nch o cr in three (3),
equally spaced rows in the center of the sheet.
Underlayment: , Lastobond TU HT or Colphene FR GP, self -adhered
5.6.4.1 All other direct -deck, adhered Soprema underlayment systems beneath foam -on the systems carry a
Maximum Design Pressure of -45 psi.
Extr W Research and Des%% LLC. Pnkvnan Report 518D1UM0 4W
Gert mteyau ONwra9l�o9 eEomox(zunFBcNoi wnfiVAwAiI m R2569-R13
Soprema, I m Revision 1L• 1. 0/WIM7
Pages orb
1 � jl
TRINITY I.ERD
5.6.4.2 For mechanically attached Base Sheet, the maximum design pressure.for the selected assembly shall meet
or exceed that required under FRSA/TRl April 2612 (04-12), Appendix A, Table 1A.
Alternatively, the maximum design pressure for the selected assembly shall meet or exceed the Zone 1
design pressure determined in accordance. with FBC 1609. In this case, Zones 2 and 3 shall employ an
attachment density designed by a qualified design professional to resist the elevated pressure criteria.
Commonly used methods are ANSI/SPRI . WD1, FM Loss: Prevention Data Sheet 1-29 and Roofing
Application Standard RAS 117. Assemblies, marked with an asterisk* carry the limitations set forth in
Section 2.2.10.1 of FM Loss Prevention Data Sheet 1-29 (January 1016) for Zone 2/3 enhancements.
5.7 Exposure Limitations:
Lastobond-Eaves-Protection Sheet, Lastobond 195,Lastobond Eco, Lastobond Smooth Seal HT, RESISTO
LB1236 Grip -Rite: Eave & Valley Protector or RESISTO L61244 shall not be left exposed for longer than 30-
days. afteririst-allation.
Lastabond Shield, Lastobond Pro HT N, RESISTO SA SMOOTH PLY-40, Lastobond Shield HT or Lastobond
Pro HT S shall not be left exposed for.long er than 90-days after installation.
Lastoborid TLI HT or Colphene FR GR.shall not be left exposed for longer than 180-days after installation.
5.8 Tile Slippage Limitations (TAS 103 per FRSA/TRI April 2012 (04-12)):
When loading roof tiles on the underlaym„ent in direct -deck the assemblies, the maximum roof slope shall
be as follows. These slope limitations can only be exceeded by using battens during loading of the roof
tiles.
A x TpeLE2 TILE$IIPPAGELIMRA'iIONSFORDIREC7-DECKTILEINSTAu:AT10N5:
Underlayment
Tile Profile
Staging Method
Maximum
Slope
Flat
Max.10-tile stack
6:12
Lugged
Max :10-tile stack
5:12
Max.10-tile stack (bottom 2-tile stack
shall be inverted,.followed by 8 tiles high 6:12
on slope; as shown below)
Lastobond TU HT
4.
Lugged
j
Colphene FR GR
Flat
Max ibLtile stack 5:12
Lugged
Max.10-tile stack
6:12
Exterior Research and Design, LLC. Evaluation Report S18010.06.09-R11
CerWcuteojAvthorlmtioa#9S03 e"EDITION(2017)FBCNONHVHZEVALUATION FL2569-RB
Soprema, Inc Revision 11:10/06/2017
Page 6 of8
q0TRIt"MIERD
6. INSTAt1A'now:
6.1 Soprema Roof Underlayments shall be installed in accordance with Soprema published installation
requirements subject to the limitations set forth in Section 5 herein and the specifics noted below.
6.2 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly
to remove any dust and debris prior to application, and prime the substrate with Elastocol Stick, Elastocol
600c or RESISTO EXTERIOR PRIMER (if applicable).
V«7�j�--*�������W��iJ'�.T�{Qf7�,�•�l��- f '•�F� t._ S+Y- i �;
�1 �M���C��}wY�s! � ,`��ry JypM�MY�iW�¢!� �iJ+!� . g2 .„i? JC Y - �i•.:. 1.%-�
,63.1 Shallbeinstalled in compliance with the requirements for ASTM D1970 underfavment in �FBC Table
2507.1.1 for the type of prepared roof covering to be installed.
6.3.2 Non -Tile Applications:
While priming is optional, Soprema. recommends priming with Elastocol Stick, Elastocol 600c or RESISTO
EXTERIOR PRIMER if the final roof cover is not slated for installation within 24 hours.
Apply sheet parallel to the roof edge. Roll out approximately 10 ft of membrane and peel back the first 3
ft of release film.
Adhere the exposed part to the substrate and unroll the remaining membrane as far as possible.
Once the entire length of membrane is in place, pe6off the release film diagonally while holding the
membrane tight. Firmly roll the membrane into place to achieve a bond.
Horizontal seams should be minimum 3-inches, configured to shed water- Vertical seams should be 6-
inches and staggered not less than 2-ft from vertical seams in the course below. All over -granule end -laps
shall be sealed using either heat -welding or hot air welding techniques.
When installing at slopes above 8:12, Soprema recommends back -nailing in the overlap area at the top of
the sheet at 124nch o.c.
For Valleys and Ridges: Cut underlayment into 4 to 6 foot lengths. Peel the release paper and center sheet
over valley or ridge. Drape and press sheet into place, working from the center of the valley or ridge in
each direction. For valleys, apply the sheet starting at the lowest point and work upward.
6.3.3 Tile Applications (lastobond TU HT or Colphene FR GR only):
Reference is made to FRSA/TRI April 2012 (04-12) Installation,Manual and Table 1 herein, using the
instructions noted above as a guideline.
For foam -on file applications, reference is made to Section 5.6.4 herein for wind resistance limitations that
fall outside the scope of FRSA/TRI April 2012 (04-12).
Tile shall be loaded and staged in a manner that prevents tile slippage and/or damage to the
underlayment. See Table 2 herein, and Soprema published requirements for file staging.
7. BUILDING POWITREt(UIREMENT3:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product I -
Enerior Research and DwIgn, LM Evaivat(on ReportS18010.OSA9-Ril
eeo/AadmrTmttare9�4olr 6'EDITION(20171FBC11101" WEVAWA710N R2569413
sopmmas hic. ReVislon 1k 20106/2Q17
Paxe7of8
�jTRHIM'MD
MMUFACPMNG PLAIWM
Contact the noted CIA agency for information on product locations covered for FJLC. 61620-3 CIA requirements.
The following plants have qualified products under their respective physical properties specifications.
I
Aam
LasInhand Weld, REMM SAMOM PLY40, Lastabond Sdeld HT,
Drununondville,
LasbDbond Pro trr-m Lmtobond Pro HT-% Lastoband 1W, Lwtobond
QC (Canada)
ASIM DIM
Bnw ProWctmagmef4 taAobmd Eam, Liftband Smooth Seal HT
RESIMIM23rx Wmw%urwGrip-Rite Ewe&ValWyPwft0w,
MISTO LB1244
ASrM MM & FRSAfM 04-12
Calphene FR GR
bmbobmrd M Las bond SMS PrOMMIJOn Sheet; LwWband Em,
Wadsvjorft OH
ASTM D1970
Wsk&wd Smooth Seal HT, REUM UWM PfimeSmum Grip-RAe
lave & Valley PwUxW RE RM LM244
ASTM D1970 & RSAfM 04-12
Iaftbond TU W; Cdphme FH GR
Laswmw M Lastobond raves Pmtmgon Steel; Lambond Eco,
Gwipor% ms
ASTM DL970
I
Laftband&nooth Seal HT, RE' MO 183230 PdmeSouroeGM)-flMe
I
---
Eave&Valley Protect REASTOL01244
QUALITY ASSURANCE ENTITY.
UL, LLC— QUA9625, (314) S78-3406, kchancellor@us.ul.com
- END OF EVALUATION REPORT -
Oftibritmearch and DeskkLLC- EyahmWnRepwtS1M0ALW4U1
Gs eojaotlrarkvEtmrlR 6P13)M0N(Z0MFBCN0N4MaEVALk;A7M I R2569-1113
Salmr,m, Im RWAS11M11:10106IM7
112080fe