HomeMy WebLinkAboutEVALUATION REPORT - UNDERLAYMENTSNEW I etc.
Certificate ofAuthonzation #32455
353 Christian Street, Unit #13
Oxford, CT 06478
(203) 262-9245
EN b INEER EVALUATE TEST CONSULT CERTIFY
EVALUA�l ON REPORT
Polyglass SA, Inc. Evaluation Report P12060.02.09-R24
1111 Wei Newport Center Drive FL5259-1128
Deerfield Beach, FL 33442 Date of Issuance: 02/24/2009
(954) 233-1230 Revision 24: 01/24/2018
SCOPE:
This Eval ation Report is issued under Rule 61G20-3 and the applicable rules and regulations governing the use of
construct Din materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen, P.E.
for use oT the product under the Florida Building Code and Florida Building Code, Residential Volume. The products
described herein have been evaluated for compliance with the a Edition (2017) Florida Building Code sections noted
herein.
LABELING: (Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted herein.
CONTINU COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality A surance documentation changes, or provisions of the Code that relate to the product change. Acceptance of this
Evaluatiot Report by the named .client constitutes agreement to notify Robert Nieminen, P.E. of any changes to the
product(s!, the Quality Assurance or the production facility location(s). NEMOJetc. requires a complete review of this
Evaluatior Report relative to updated Code requirements with each Code Cycle_
ADVERTISE I ZIENT: The Evaluation Report number preceded by the words "NEMO l etc. Evaluated" may be displayed in
advertisir 3,, literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTIOI I: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or its
distributors and shall be available for inspection at the job site at the request of the Building Official.
This Evaluation Report consists of pages 1 through 14.
Prepared joy:
Robert J.I
Florida Rei
CERTIFICATH
1. NEMC
distrib
2. NEMC
3. Rober
which
4. Rober'
produ
5. This is
Nieminen, P.E.
ration No. 59166, Florida DCA ANE1983
The facsimile seal appearing was authorized by Robert Nieminen,
P.E. on 01/24/2018. This does not serve as an electronically
signed document.
N OF INDEPENDENCE:
etc. does not have, nor does it intend to acquire or will it acquire, a financial interest in any company manufacturing or
ting products it evaluates.
etc. is not owned, operated or controlled by any company manufacturing or distributing products it evaluates.
Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
ie evaluation reports are being issued.
Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
building code evaluation. Neither NENIOIetc. nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
an which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
illy for that purpose.
4.
ONEMOjetc.
Examination
Reference
Date
ST 6049)
Physical Properties
P40390.08.12-1
08/06/2012
ST 6049)
T
Physical Properties
P40390.08.12-2
08/07/2012
6049)
Physical Properties
C41420.09.12-3
09/11/2012
iST
ER (TST 6049)
Wind Uplift
P39680.03.13
03/04/2013
ER (TST 6049)
Physical Properties
P45370.04.13
04/26/2013
ER (TST 6049)
Wind Uplift
P1738.02.07-R2
04/29/2013
ER, (TST 6049)
Wind Uplift
11757.04.01-1-Ri
04/30/2013
ER I(TST 6049)
Wind Uplift
P41630.08.13
08/06/2013
ER (TST 6049)
Wind Uplift
P11751.05.03-Ri
11/26/2013
ER (TST 6049)
Wind Uplift
P11781.11.03-Ri
11/26/2013
ER (TST 6049)
Physical Properties
P45270.05.14
05/12/2014
ER (TST 6049)
Physical Properties
6020.07.14-1
09/08/2014
ER (TST 6049)
Physical Properties
6020.09.14-2
09/08/2014
ER (TST 6049)
Physical Properties
6020.09.14-3
09/08/2014
ER (TST6049)
Physical Properties
6020.09.14-4
09/08/2014
.ER (TST 6049)
Physical Properties
6020.09.14-5
09/08/2014
ER (TST 6049)
Physical Properties
6020.09.14-6
09/08/2014
ER (TST 6049)
Physical Properties
P46520.10.14
10/03/2014
ER (TST 6049)
Physical Properties
P43290.10.14
10/17/2014
ER (TST 6049)
Physical Properties
PLYG-SC7550.03.15
03/24/2015
ER (TST 6049)
Physical Properties
P40390.04.15
04/03/2015
ER (TST 6049)
Physical Properties
P44360.10.14-111
05/18/2015
ER (TST 6049)
Physical Properties
PLYG-SC8080.05.15-1
05/20/2015
ER (TST 6049)
Wind Uplift
PLYG-SC8905.05.16-1
05/17/2016
ER (TST 6049)
Physical Properties
PLYG SC8080.07.16
07/16/2016
ER (TST 6049)
Wind Uplift
PLYG-SC12025.10.16
10/12/2016
ER i (TST 6049)
Physical Properties
PLYG-SC13040.12.16
12/27/2016
ER (TST 6049)
Physical Properties
PLYG-SC11900.03.17
03/10/2017
ER (TST 6049)
Physical Properties
PLYG-SC12115.08.17
08/08/2017
ICC ES (EVL 2396)
IBC Compliance
ESR-1697
11/01/2014
Mi i-Dade (CER 1592)
HVHZ Compliance
NOA 14-0717.08
01/22/2015 .
Polglass USA
Manufacturing Affidavit
Products Current
02/18/2009
Pol,lilass USA
P/L Affidavit
Mule -Hide Cross Ltg
03/01/2008
Pol glass USA
Materials Affidavit
Polystick SA Compound
08/18/2011
UL, LC. (QUA9625)
Quality Control
Service Confirmation
Exp. 10/05/2018
PR DUCT DESCRIPTION:
I I
4.1
I Mechanically Fastened Underlayments:
4.11
Elastobase is a fiberglass reinforced, SBS modified bitumen base sheet.
4.1
Elastobase P is a polyester -reinforced, SBS modified bitumen
base sheet.
4.13
Polyglass GZ Base is a fiberglass -reinforced, asphaltic base
sheet.
4.1
j4 Polyglass APP Base is a fiberglass -reinforced, APP modified bitumen base sheet.
4.2II
Self -Adhering Underlayments:
4.22 Polystick IR-Xe is a nominal 60-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with an
aggregate surface; meets ASTM D1970.
4.2 Polystick TU Plus is a nominal 80-mil thick rubberized asphalt waterproofing membrane, glass fiber reinforced, with a
polyester fabric surface; meets ASTM D1970 and FRSA/TRI April 2012.
NEMO IF C, U.C. Evaluation Report P12050.02.09-R24
Certijlcat 01 fAuthorization #32455 6TM EDITION (2017) FBC NON-HVHZ EVALUATION FL5259-R28
Polyglass Roof Underlayments, (954) 233-1M Revision 24: 01/24/2018
Page 3 of 14
ONEMOjetc.
5. Allowable Roof Covers:
TABLE 1: ROOF COVER OPTIONS
Underlayment
Asphalt Shingles
Nail -On Tile
Foam -On Tile
Metal
wood Shakes
& Shingles
Slate
Ela
tobase
I
Yes
yes
(Base Sheet In 2-ply system)
Yes
(Base Sheet In 2-ply system)
Yes
Yes
Yes
Ela
J
tobase P
Yes
(Base Sheet n es
2-ply system)
e
(Base Sheet nt -ply system)
Yes
Yes
Yes
Pal
lass G2 Base
No
Yes
(Base Sheet in 2-ply system)
Yes
(Base Sheet in 2-ply system)
No
No
No
Pol
glass APP Base
No
Yes
(Base Sheet in 2-ply system)
Yes
(Base Sheet in 2-ply system)
No
No
No
Pal
stick MTS ar MTS PLUS
es
es
Na
Yes
Yes
Yes
Poll
ticklR-Xe
Yes
No
No
No
Yes
Yes
PolystickTU
P
No
Yes
Yes (See 5.5.1)
No
No
No
PolystickTU
Plus
Yes
Yes
Yes (See 5.5.1)
Yes
Yes
Yes
PolystickTU
Max
No
Yes
Yes (See 5.5.1)
Yes
No
No
Polystick
Dual Pro
Yes
No
No
Yes
Yes
Yes
Pal'ystickTile
Pro
Yes
Yes
Yes (See 5.5.1)
Yes
Yes
Yes
Pol stick MU-X
Yes
No
No
Yes
Yes
Yes
Ela oflex S6 G
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Ela (oflex 56 G FR
Yes
Yes
No
No
Yes
Yes
Ela (oflex GTU
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Pol 11ex G
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Pal
lex G FR
Yes
Yes
No
No
Yes
Yes
Pol ex SAP or SAP FR
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
Mu
or
e-Hide SA-APP Cap Sheet
-APP Cap Sheet (FR)
Yes
Yes
Yes (See 5.5.1)
No
Yes
Yes
5.5I11 "Foam -On Tile" is limited to use of the following Approved tile adhesives / underlayment combinations.
TABLE
1A: ALLOWABLE TILE ADHESIVE / UNDERLAYMENT COMBINATIONS)
Adhesive
Florida Product
Underlayments
Approval
DA
Foam Touch'n Seal Storm Bond Roof
FL14506
PolystickTU Plus, PolystickTU Max
THEPdhesive
Do
TileBond'"
FL22525
Polystick TU P, PolystickTU Plus, Polyflex SAP or Tile Pro
PolystickTU P, PolystickTU Plus, PolystickTU Max, Polystick Tile Pro,
ICP
dhesives Polyset® AH-160
FL6332
Elastoflex G TU, Elastoflex S6 G, Polyflex G, Polyflex SAP, Polyflex SA Cap FR,
Mule -Hide SA-APP Cap Sheet or Mule -Hide SA-APP Cap Sheet (FR)
Polystick TU P, Polystick TU Plus, Polystick TU Max, Polystick Tile Pro,
ICP
dhesives Polyset® RTA-1
FL6276
Elastoflex G TU, Elastoflex S6 G, Polyflex G, Polyflex SAP, Polyflex SA Cap FR,
Mule -Hide SA-APP Cap Sheet or Mule -Hide SA APP Cap Sheet (FR)
1 Refer Tile Manufacturer's or Adhesive Manufacturer's Florida Product Approval for Overturning Moment Resistance Performance.
NEMO IF C, U.C. Evaluation Report P12060.02.09-R24
Certifkot IofAuthorization #32455 6TM EDITION (2017) FBC NON-HVHZ EVALUATION FLS259-1128
Polyglass Roof Underlayments, (954) 233-1230 Revision 24: 01/24/2018
Page 5 of 14
OMEMO I etc.
5.i Allowable Substrates:
Polystick (all variations), Dual Pro, Tile Pro, Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet
(FR) self -adhered to:
➢ New untreated plywood; ASTM D41 primed new untreated plywood; Existing plywood; ASTM D41 primed existing
plywood; New or existing, unprimed OSB; ASTM D41 primed OSB; Southern Yellow Pine; ASTM D41 primed
Southern Yellow Pine; ASTM D41 primed structural concrete; Huber Engineered Woods "ZIP System" Panels
(designed and installed to meet wind loads for project).
Note: Polyglass does not require priming of new or existing plywood or OSB sheathing. New or existing plywood or
OSB sheathing should be cleaned of all dirt and debris prior to application of Polystick membranes.
Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR in hot asphalt to:
➢ ASTM D41 primed structural concrete.
Polyflex G or Polyflex G FR torch -applied to:
➢ ASTM D41 primed structural concrete.
Bond -to -Insulation:
Polystick (all variations), Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) self -adhered
to:
➢ ASTM C1289, Type II, Class 1 polyisocyanurate or Type V polyisocyanurate-composite insulation; Dens Deck
DuraGuard; Dens Deck Prime; or SECUROCK Gypsum -Fiber Roof Board.
Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR in hot asphalt to:
➢ Dens Deck Prime or SECUROCK Gypsum -Fiber Roof Board.
Polyflex G or Polyflex G FR torch -applied to:
➢ ASTM D41 primed structural concrete; Dens Deck Prime or SECUROCK Gypsum -Fiber Roof Board.
For installation under mechanically attached prepared roof coverings, insulation shall be attached per minimum
requirements of the prepared roof covering manufacturer's Product Approval. For installations under foam -on tile
systems, insulation attachment shall be designed by a qualified design professional and installed based on testing of
the insulation/underlayment system in accordance with FBC Section 1504.3.1.
Bond to Mechanically Attached Base Laver:
Polystick (all variations), Polyflex SAP or SAP FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR) Dual Pro or
Tile Pro self -adhered to:
➢ ASTM D226, Type I or II felt; Elastobase; Elastobase P or Mule -Hide Nail Base.
Elastoflex G TU, Elastoflex S6 G or Elastoflex S6 G FR in hot asphalt to:
➢ ASTM D226, Type 1 or If felt; Elastobase; Elastobase P, Mule -Hide Nail Base or Polyglass G2 Base.
Polyflex G or Polyflex G FR torch -applied to:
➢ Elastobase; Elastobase P, Mule -Hide Nail Base, Polyglass G2 Base or Polyglass APP Base.
For installations under mechanically attached prepared roof coverings, base layer shall be attached per minimum
codified requirements. For installations under foam -on tile systems, base layer shall be attached per minimum
requirements of FRSA/TRI April 2012 (04-12), Appendix A, Table 1, or as listed in Section S.6.4 herein, or as tested in
accordance with FBC Section 1504.3.1.
NEMO i CLLC. Evaluation Report P12060.02.09-R24
Certiif. 0;Auth0,.z,W,#32455 6EDITION (2017) FBC NON-HVHZ EVALUATION s FL5259-1128
Polyglass Roof Underlayments, (954) 233-1230 Revision 24: 01/24/2018
Page 6 of 14
6.
ONEMOletc.
6.1 Polyglass Roof Underlayments shall be installed in accordance with Polyglass published installation requirements
subject to the Limitations set forth in Section 5 herein and the specifics noted below.
6.2 Re -fasten any loose decking panels, and check for protruding nail heads. Sweep the substrate thoroughly to remove
any dust and debris prior to application, and prime the substrate (if applicable).
6:4I Elastobase, Elastobase P or Mule -Hide Nail Base:
6. 1 Non -Tile Applications:
Shall be installed in compliance with the codified requirements for ASTM D226, Type If underlayment in FBC Table
1507.1.1 for the type of prepared roof covering to be installed.
Elastobase, Elastobase P or Mule -Hide Nail Base may be covered with a layer of Polystick, Polyflex SAP, Polyflex SA
P FR, Mule -Hide SA-APP Cap Sheet or SA-APP Cap Sheet (FR), self -adhered, Elastoflex G TU, Elastoflex S6 G or
Elastoflex S6 G FR in hot asphalt or Polyflex G or Polyflex G FR, torch applied. Roof cover limitations are those are
those associated with the top -layer underlayment, as set forth in Table 1.
6. 2 Tile Applications:
Elastobase, Elastobase P or Mule -Hide Nail Base are limited to use as a mechanically attached base sheet in the"Two
Ply System" from FRSA/TRI April 2012 (04-12). Reference is made to Table 1 and Section 5.6.4 herein, coupled with
FRSA/TRI April 2012 (04-12) Installation Manual.
Shall be installed in compliance with the codified requirements for ASTM D1970 (except Polystick TU P) underlayment
in FBC Table 1507.1.1 for the type of prepared roof covering to be installed.
Direct -to -Deck with Mechanically Fastened Roof Covers:
All self -adhering materials, with the exception of Polystick TU Plus, Polyflex SAP or SAP FR and Mule -Hide SA-APP
Cap Sheet or SA-APP Cap Sheet (FR) should be back -nailed in selvage edge seam in accordance with Polyglass / Mule -
Hide back nailing guidelines. Nails shall be corrosion resistant, 11 gauge ring -shank type with a minimum 1-inch
diameter metal disk or Simplex -type metal cap nail, at a minimum rate of 12" o.c. Polystick TU Plus should be back -
nailed using the above noted fasteners and spacing, in area marked "nail area, area para claval" on the face of
membrane. The head lap membrane is to cover the area being back -nailed.
All seal -lap seams (selvage laps) must be
firmly rolled with a minimum 28 lb. hand .
roller to ensure full contact and adhesion. �•:;r, ,
For Dual Pro and Tile Pro, align the edge of
the top sheet to the end of the glue pattern
(the sheet will overlap the fabric).
View of ovelap Seam of Dual Pro and Tile Pro
All over -fabric and over -granule end -laps shall have a 6-inch wide, uniform layer of Polyplus 50 Premium Modified
Wet/Dry Cement or Polyglass PG500 Modified Cement applied in between the application of the lap.
Polystick TU Plus, Dual Pro and Tile Pro may not be used in any exposed application such as crickets, exposed valleys,
or exposed roof to wall details
NEMO C, LLC Evaluation Report P12060.02.09-R24
Certificat I of Authorization #31455 d' EDITION (2017) FBC NON-HVHZ EVALUATION . FL5259-R28
Polyglass Roof Underlayments; (954) 233-1230 Revision 24: 01/24/2018
Page 12 of 14