HomeMy WebLinkAboutEVALUATION REPORT - MODIFIED BITUMENEXTERIOR RESEARCH & DESIGN, U.C.
Certificate of Authorization #9503
\IJ TRINITY ' 353 Christian Street
ERD Oxford, CT 06478
(203) 262-9245
JALUATION REPORT SGANNED
DlyglasS USA, Inc. BY Evaluation Report P9290.0 -R20
50 Lyon Drive FL165454-R22
:rnley, NV 89408.. St Lucie County Date of issuance: 02/11/2008
i70) 384-1230 Revision 20: 09/12/2017
This Evaluation Report is issued under Rule 611320-3 and the applicable rules and regulations governing the use of
construction materials in the State of Florida. The documentation submitted has been reviewed by Robert Nieminen,
P.E. for use of the product under the Florida Building Code. The product described herein has been evaluated for
compliance with the 6th Edition (2017) Florida Building Code sections noted herein.
DESCRIPTION: Polyglass SBS and APP Modified Bitumen Roof Systems
LABELING: Labeling shall be in accordance with the requirements the Accredited Quality Assurance Agency noted
herein.
CONTINUED COMPLIANCE: This Evaluation Report is valid until such time as the named product(s) changes, the referenced
Quality Assurance documentation changes, or provisions of the Code that relate to the product change. Acceptance of
this Evaluation Report by the named client constitutes agreement to notify Robert Nieminen, P.E. if the product
changes or the referenced Quality Assurance documentation changes. Trinity) ERD requires a complete review of this
Evaluation Report relative to updated Code requirements with each Code Cycle.
ADVERTISEMENT: The Evaluation Report number preceded by the words "Trinity I ERD Evaluated" may be displayed in
advertising literature. If any portion of the Evaluation Report is displayed, then it shall be done in its entirety.
INSPECTION: Upon request, a copy of this entire Evaluation Report shall be provided to the user by the manufacturer or
its distributors and shall be available for inspection at the job site at the request of the Building Official.
Evaluation Report consists of pages 1 through 6, plus a 58-page Appendix.
Prepared by:
Robert J.M. Nieminen, P.E.
Florida Registration No. 59166, Florida DCAANE1983
The facsimile seal appearing was authorized by Robert Nieminen,
P.E. an 09/1212017. This does not serve as an electronically signed
document.
CERTIFICATION OF INDEPENDENCE:
1. Exterior Research & Design, LLC. d/b/a Trinity I ERD does not have, nor does it intend to acquire or will it acquire, a financial interest
in any company manufacturing or distributing products it evaluates.
2. Exterior Research &Design, I.I.C. d/b/a Trinity I ERD Is not owned, operated or controlled by any company manufacturing or
distributing products it evaluates.
3. Robert Nieminen, P.E. does not have nor will acquire, a financial interest in any company manufacturing or distributing products for
which the evaluation reports are being issued.
4. Robert Nieminen, P.E. does not have, nor will acquire, a financial interest in any other entity involved in the approval process of the
product.
5. This is a building code evaluation. Neither Trinityl ERD nor Robert Nieminen, P.E. are, in any way, the Designer of Record for any
project on which this Evaluation Report, or previous versions thereof, is/was used for permitting or design guidance unless retained
specifically for that purpose.
` TRINITY !ERD
SYSTEMS EVALUATION:
1. SCOPE:
Product Category: Roofing
Sub -Category: Modified Bitumen Roof Systems
Compliance Statement: Polyglass SBS and APP Modified Bitumen Roof Systems, as produced by Polyglass USA,
Inc., have demonstrated compliance with. the following sections of the 6ei Edition (2017) Florida Building Code
through testing in accordance with the following Standards. Compliance is subject.to the Installation Requirements
and Limitations / Conditions of Use set forth herein.
2. STANDARDS:
Section
Property
Standard
Year
1504.3.1
Wind
FM 4474
2011
1504.3.1
Wind
UL 1897
2012
1504.7
Impact
FM 4470
2012
1507.21.2.
Physical Properties
ASTM D6162
2008
1507.11.2
Physical Properties
ASTM D6163
2008
1507.11.2
Physical Properties
ASTM D6164
2011
1507.11.2
Physical Properties
ASTM D6222 .
2011
1507.11.2
Physical Properties
ASTM D6509
2009
3. REFERENCES:
Ent
Examination
Reference
Date
ERD (TST6049)
Physical Properties
P10490.10.08-2
10/30/2008
ERD (TST6049)
FM 4470/4474
P13760.09.09
09/10/2009
ERD (TST6049)
FM 447D/4474
P13770.09.09
09/10/2009
ERD(TST6049)
FM 4470/4474
P30540.11.09-R1
il/30/2009•
ERD (TST6049)
FM 4470/4474
P30550.12.09
12/02/2009
ERD (TST6049)
Physical Properties
P33960.12.10
12/30/2010
ERD (TST6049)
FM 4470/4474
P33970.03.11
03/15/2011
ERD (TST6049)
Physical Properties
P37590.03.13-3A
03/06/2013
ERD (TST6049)
FM 4470/4474
P39680.03.13
03/04/2013
ERD (TST6049)
Physical Properties
P37590.03.13-1-R1
06/26/2613
ERD (TST6049)
Physical Properties
P37590.03.13-2-R1
07/01/2013
ERD (TST6049)
Physical Properties
P37590.07.13-2
07/01/2013
ERD (TST6049)
Physical Properties
P37590.03.13-5-111
07/01/2613
ERD (TST6049)
Physical Properties
P37590.07.13-1
07/02/2013
ERD (TST6049)
FM 4470/4474
P41630.08.13
08/06/2013
ERD (TST6049)
Physical Properties
P45940.09.13
09/04/2013
ERD (TST6049)
Physical Properties
P44370.10.13
10/04/2013
ERD (TST6049)
Physical Properties
P39520.09.14-2
09/11/2014
ERD (TST6049)
FM 4470/4474
SC6160.11.14
11/10/2014.
ERD (TST6049)
Physical Properties
PLYG-P45440SC.03.15-1
03/31/2015
ERD (TST6049)
Physical Properties
SC5170.0SAS
05/08/2015
ERD (TST6049)
FM 4474
SC8085.05.15
05/19/2015
ERD (TST6049)
Physical Properties
SC5170.12.15
12/29/2015
ERD (TST6049)
FM 4470/4474
SC9455.15
04/01/2016
ERD(TST6049)
FM 4470/4474
PLYG-SC8905.05.16-1
05/17/2016
ERD (TST6049)
FM 4470/4474
PLYG-SC8905.05.16-2
05/17/2016
ERD (TST6049)
FM 4470/4474
PLYG-SC10815.07.16-RI
09/23/2016
ERD (TST6049)
UL1897
PLYG-SC12025.10.16
10/12/2016
ERD (TST6049)
FM 4470/4474
PLYG-SC11475.16
11/17/2016
ERD (TST6049)
FM 4470/4474/UL1897
PLYG-SC13235.01.17
01/17/2017
ERD (TST6049)
FM 4474/UL1897/TAS 114
PLYG-SC13920.05.17
05/30/2017
ERD (TST11294)
FM 4474/UL1897/TAS 114
PLYG-CTL13945.05.17-1
05/30/2017
Exterior Research and Design, U.C.
Evaluation Report P9290.02.08-R20
Certifcate of A utharkation #9503
6T"'EDITION (2017) FBC NON-HVHZ
EVALUATION
FL2654-RZZ
Polyglass Modred Bitumen Roof Systems; (570) 384-1230
Revision 20: 09/22/2027
Page 2 of 6
'� TRINITY i ERD
Entity
Examination
Reference
Date
ERD(TST11294)
FM 4474/UL1897/TAS 114
PLYG-CTL13945.05.17-3
05/30/2017
ERD(TST6049)
FM.4474/UL1897
PLYG-SC13945.05.17
05/30/2017
ERD(TST6049)
FM 4474/TAS 124
PLYG-SC15760.09.17
09/11/2017
FM Approvals (TST1867)
FM 4470
2W7A7.AM
08/04/1994
FM Approvals (TST1867)
FM 4470
OD3A3.AM
04/04/1997
FM Approvals (TST1867)
FM 4470
2DOAO.AM
12/23/1998
FM Approvals (TST1867)
FM 4470
2D5A9.AM
06/22/1999
FM Approvals (TST1867)
FM 4470
3006646
01/04/2000
FM Approvals (TST1867)
FM 4470
3001334
01/25/2000
FM Approvals (TST1867)
FM 4470
3001334
02/15/2000
FM Approvals(TST1867)
FM 4470
3000857
01/12/2000
FM Approvals (TST1867)
FM 4470
3004091
01/12/2000
FM Approvals(TST1867)
FM 4470
3CO6115
05/02/2001
FM Approvals (TST1867)
FM 4470
3012321
07/29/2002
FM Approvals (TST1867)
FM 4470
3014692
08/05/2003
FM Approvals (TST1867)
FM 4470
3014751
08/27/2003
FM Approvals (TST1867)
FM 4470
3007170
01/13/2004
FM Approvals (TST1867)
FM 4470
3019317
06/30/2004
FM Approvals (TST1867)
FM 4470
3020703
07/30/2004
FM Approvals (TST1867)
FM 4470/4474
3018332
01/32/2006
FM Approvals (TST1867)
FM 4470/4474
3023368
03/20/2006
FM Approvals (TST1867)
FM 4470/4474
3024594
05/23/2006
FM Approvals (TST1867)
FM 4470/4474,
3023458
07/18/2006
FM Approvals (TST1867)
FM 4470/4474
3030668
09/12/2007
FM Approvals (TST1867)
FM 4470/4474
3032172
06/12/2009
FM Approvals (TST1867)
FM 4470/4474
3049631
04/21/2014
FM Approvals (TST1867)
FM 4470/4474
3057029
02/02/2017
PRI (TST5878)
Physical Properties
PUSA-062-02-01
12/04/2007
PRI (TST5878)
Physical Properties
PUSA-061-02-02
01/28/2008
PRI (TST5878)
Physical Properties
PUSA-064-02-02
02/27/2008
PRI (TSTS878)
Physical Properties
PUSA-062-02-02
12/04/2008
PRI(TST5878)
TAS 114
PUSA-188-02-01
02/08/2017
PRI (TST5878)
TAS 114
PUSA-188-02-02
02/08/2017
PRI (TST5878)
TAS 114
PUSA-188-02-03
02/08/2017
PRI (TST5878)
TAS 114
PUSA-202-02-01
05/17/2017
PRI(TSTS878)
TAS 114
PUSA-202-02-02
05/17/2017
Miami -Dade (CER1592)
HVHZ Compliance
Various NOAs
Various
Miami -Dade (CER1592)
Proposal for Review
10-0823
10/12/2010
UL LLC (QUA9625)
Quality Control
Service Confirmation, R14571
Exp. 10/06/2018
4. PRODUCT DESCRIPTION:
This Evaluation Report covers Polyglass Modified Bitumen Roof Systems installed in accordance with Polyglass USA,
Inc. published installation instructions and the Limitations / Conditions of Use herein. The following Polyglass
membranes make up the subject systems.
:TneiE i ROL[-GOODS FOR POkYG1 ASS MODIFIED $n UMEN ROOF SYSTEMS
Type
Product
Specification
Reference
Grade
Type
Base Sheets
Polyglass G2 Base
ASTM D4601
N/A
II
Polyflex SA Base
ASTM D4601
N/A
II.
Polyglass APP Base
ASTM D6509
N/A
N/A
Exterior Research and Design, U.C. Evaluation Report P9290.02.08-RZO
CerUjlcate ofAuthorrsotion #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL1654-R22
Polyglass Modified Bitumen Roof Systems; (570)'384-1230 Revision 20: 09/12/2017
Page 3 of 6
�`- :' TRINITY I ERD
TABLE IICONTINUEl7.� ROLL. GOADS FOR PALYGLlII$S MODIFIED BITUMEN ROOF SYiTEINS
Type
Product
Specification
Reference
Grade
Type
SBS Membranes
Polyglass HT Base 650
ASTM D6162
S
III
Elastobase
ASTM D6163
S
I
Elastoflex V
ASTM D61.63 ,
.q_p�
FElastofl_euTSq;V�Base't'
f ASTNIkD6163;Tafjle}2�
= S4 L�
J y
Elastoflex SA V FR Base
ASTM D6163, Table 2
S
I
Elastoflex SA V Plus
ASTM D6163
S
I
Elastoflex SA V Plus FR
ASTM D6163
S
I
Elastobase Poly
ASTM D6164
S
I
Elastoflex 56
ASTM D6164
S
I
Elastoflex 56 Type II
ASTM D6164
S
II
Elastoflex VG
ASTM D6163
G
I
Elastoflex VG FR
ASTM D6163
G
I
SBS Membranes
Elastoflex S6 G
ASTM D6164
G
I
Elastoflex S6 G FR
ASTM D6164
G
I
Polyfresko G SBS (sand or poly -film backed)
ASTM D6164
G
I
Polyfresko G SBS FR (sand or poly -film backed)
ASTM D6164
G
I
Elastoshield TS G
ASTM D6164
G
I
Elastoshield T5 G FR t
ASTM D6164
G
I
as"ltoflexT5A P'i I.- —; ;,+
rtA5T11/IrD61�64
y G e .
..,,.I
tYs-toflex SA P FR
ASTM D6164
G
I
Polyreflect
ASTM D6164
S
I
APP Membranes
Polyflex
ASTM D6222
S
I
Polyflex G
ASTM D6222
G
I
Polyflex G FR
ASTM D6222
G
I
Polyfresko G
ASTM D6222
G
I
Polyfresko G FR
ASTM D6222
G
I
Pol bond
ASTM D6222
S
I
Polybond G
ASTM D6222
G
I
Polyflex SA P
ASTM D6222
G
I
Polyflex SA P FR
ASTM D6222
G
I
Polyfresko G SA
ASTM D6222
G
I
Polykool
ASTM D6222
S
I
S. LIMITATIONS:
5.1 This is a building code evaluation. Neither TrinitylERD nor Robert N)eminen, P.E. are, in any way, the
Designer of Record for any project on which this Evaluation Report, or previous versions thereof, is/was used
for permitting or design guidance unless retained specifically for that purpose.
5.2 This Evaluation Report is not for use in FBC HVHZ jurisdictions.
5.3 Refer to a current Approved Roofing Materials Directory for fire ratings of this product.
5.4 For steel deck installations, foam plastic insulation shall be separated from the building interior in accordance
with FBC 2603.4 unless the exceptions stated in FBC 2603.4.1 and 2603.6 apply.
5.5 The roof system evaluation herein pertains to above -deck roof components. Roof decks and. structural
members shall be in accordance with FBC requirements to the satisfaction -of the Authority Having
Jurisdiction. Load resistance of the roof deck shall be documented through proper codified and/or FBC
Approval documentation.
5.6 For recover installations, the existing roof shall be examined in accordance with FBC 1511.
Exterior Research and Design,, U.C. Evaluation Report P9290.02.08-1120
Certificate ofAuthorkation N9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL1654-RZZ
Polyglass Modified Bitumen Roof Systems; (570) 384-1230 Revision 20; 09/12/2017
Page 4 of 6
t1',tr
''J. TRINITY I ERD
5.7 For mechanically attached insulation or membrane or strip -bonded insulation, the maximum design pressure
for the selected assembly shall meet or exceed the Zone 1 design pressure determined in accordance with
FBC Chapter 16. Zones 2 and 3 shall employ an attachment density designed by a qualified design
professional to resist the elevated pressure criteria. Commonly used methods are ANSI/SPRI WD1, FM Loss
Prevention Data Sheet 1-29, Roofing Application.Standard RAS 117 and Roofing Application Standard RAS
237. Assemblies marked with an asterisk* carry the limitations set forth in Section 2.2.10.1 of FM Loss
Prevention Data Sheet 1-29 (January 2016) for Zone 2/3 enhancements.
5.8 For assemblies with all components fully bonded in place, the maximum design pressure for the selected
assembly shall meet or exceed critical design pressure determined in accordance with FBC Chapter 16. No
rational analysis is permitted for these systems.
5.9 For mechanically attached insulation or membrane over existing roof decks, fasteners shall be tested in the
existing deck for withdrawal resistance. A qualified design professional. shall review the data for comparison
to the minimum requirements for the system. Testing and analysis shall be in accordance with ANSI/SPRI
FX-1 or Testing Application Standard TAS 105.
5.10 For bonded insulation or membrane over existing substrates in a re -roof (tear off) or recover installation, the
existing deck or existing roof surface shall be examined for compatibility with the adhesive to be installed. If
any surface. conditions exist that bring system performance into question, field uplift testing in accordance
with ANSI/SPRI IA-1, ASTM E907, FM Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS
124 shall be conducted on mock-ups of the proposed new roof assembly.
5.11 For bonded insulation or membrane over existing substrates in a recover installation, the existing roof
system shall be capable of resisting project design pressures an its own merit to the satisfaction of the
Authority. Having Jurisdiction, as documented through field uplift testing in accordance with ASTM E907, FM
Loss Prevention Data Sheet 1-52 or Testing Application Standard TAS 124.
5.12 Metal edge attachment (except gutters), shall be designed and installed for wind loads in accordance with
FBC Chapter 16 and tested for resistance in accordance. with ANSI/SPRI .ES-1 or.Roofing Application Standard
RAS 111,, except the basic wind speed shall be determined from FBC Figure 1609.3(1), 1609.3(2) or
1609.3(3).
5.13 Ali products in the roof assembly shall have quality assurance in accordance with FAC Rule 61G20-3.
6. INSTALLATION:
6.1 Polyglass Modified Bitumen Roof Systems shall be installed in accordance with Polyglass USA, Inc. published
installation instructions, subject to the Limitations / Conditions of Use noted herein.
6.2 System attachment requirements for wind load resistance are set forth in Appendix 1. "MDP" = Maximum
Design Pressure is the result of testing for wind load resistance based on allowable wind loads, and reflects
the ultimate passing pressure divided by 2 (the 2 to 1 margin of safety per FBC 1504.9 has already been
applied). Refer to FBC 2609 for determination of design wind loads.
Exterior Research and Design, U.C. Evaluation Report P9290.02.08-1120
Certiftcote ofAuthorhaHon #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION F1.1654-1122
Polyglass Modified Bitumen Roof Systems, (570) 384-1230 Revision 20: 09/12/2017
Page 3 of 6
TRINITY I ERD
6.3 Any of the following FBC Approved coatings may be applied to the top roof membrane without adverse effect
on the system wind load performance. Refer to current Roofing Materials Directory for fire ratings associated
with coating usage.
➢ PG200 Non-Fibered Roof Coating;
➢ PG300 Fibered Roof Coating;
➢ PG600 Non-Fibered Aluminum Roof Coating;
➢ PG650 Fibered Aluminum Roof Coating;
➢ PG700 High Quality Elastomeric Roof Coating or KM Acryl 25;
➢ PG700QS (Quick -Set) High Quality Elastomeric Roof Coating or KM Acryl 25-QS (over granule -surfaced
APP or SBS only);
➢ PG800 Asphalt Emulsion Roof Coating;
➢ .Polyplus 60 Premium Non-Fibered Aluminum Roof Coating;
➢ Polyplus 65 Premium Fibered Aluminum Roof Coating;
➢ Polybrite 70 Premium Grade Elastomeric Roof Coating or KM Acryl 15;
➢ Polybrite 70QS (Quick -Set) Premium Grade Elastomeric Roof Coating or KM Acryl 15-QS (over granule -
surfaced APP or SBS only);
➢ Polybrite 90 High Solids Silicone Roof Coating;
Polybrite 95 Silicone Roof Coating.
7. BUILDING PERMIT REQUIREMENTS:
As required by the Building Official or Authority Having Jurisdiction in order to properly evaluate the installation of
this product.
S. MANUFACTURING PLANTS:
Contact the noted QA agency for information on product locations covered for F.A.C. Rule 61G20-3 QA
requirements
9: QUALITY ASSURANCE ENTITY:
UL LLC-= QUA9625; (314) 578-3406, k.chancellor@us.ul.com
- THESS-PAGES THAT FOLLOW FORM PART OF THIS EVALUATION REPORT -
Exterior Researth and Design, I.I.C. Evaluation Report P9290.02.08-R20
Certificate of Authorisation #9503 6T" EDITION (2017) FBC NON-HVHZ EVALUATION FL1654-R22
Polyglass Modified Bitumen Roof Systems; (570) 384-1230 Revision 20: 09/12/2017
Page 5 of 6
M
\-"TRINITY;ERD
.
I _ .. TAHLEIF2 W000DEQ(S NEWCONSTR�1CTIdN,,REROOFI(ienR-0FF)aeRewvEa
i
51fS10EM7YPEE NOMaNSULA7E0;_MECHANICALLY111TACHEDBASE'5HEEr(saiEws&Pu�j;BONOED'ROOFCOVER
System
Base Sheet
Roof Cover (Note 25)
MDP
No.DedtlNote
3)
type Fasten Attach
Base Ply Cap
(Psq
SttFAoHd
xs BAte Pa:
W-i6
Min. 19/32-
Inch plywood
Elastobase, Elastobase P
(poly -Rim tap)
Dediast Hex (aka, Oekfast PL7-H-2-7/8) with Dekfast g14
orTrufast 3" Metal Insulation Plate with Tmfast HD
124nch o.c. in 4-inch lap end 12-Inch o.c. In two
(2), equally spaced, staggered center rows
SOS -SA
SBS-SA, APP-SA, SBS-
TA, APP TA
_52.5•
W 137
Min. 19/32-
Inch plywood
Elastabase, Elastobase P
(poly -film tap)
Dekfast Hex (aka, Dekfast PLT-H-2-7/8) with Dekfast e14
or Trufast 3" Metal Insulation Plate with Trufast HD
124nch o.c. In 4-Inch lap and 12-Inch o.c. intwo
(2), equally spaced, staggered center raw
PolVII SA Base
APP TA
-52.5•
W-138
IMin. 19/32-
Inch plywood
Elastobase, ElastobaseP
(poly-filmtop)
OMG Flat Bottom Plates (square) with,Roofgdp012
12-Inch o.c. in 4-inch lap and 12-Inch o.c. in two
(2), equallyspaced, staggered center taws
SBS-SA
SES-SA, APP-S,%SBS-
TA, APP TA
W-139
Min. 19/32-
Inch plywood
Elastobase, Elastobase P
(poly-Rlmtop)
OMG Flat Bottom Plates Isquare) with Ro r grip $112
12-Inch o.c. in 4-ihch lap and 12-Inch o.c. in two
(2), equally spaced, staggered center rows
Polyfiex SA Base
APP TA
-60.0•
TABLEiG:WOODDECKS NEINCONS�R4ClIONORREROOFjfEAROFF)
I
SYSTEMTYPEFNONINSU[ATED BONI)EQROOF,`COVER
m
System
Dedc Motel)
Primer
Roof Cow (Note 25)
MOP(Psf)
Jalnt Treatment
Base Ply
Ply
Cap Ply
W-240
Min' 15/32
None
None
SBS-SA
(Optional) SBS-SA, SBS-
SBS-SA, APP-SA, SBS-
-90.0
Inch plywood
TA,APP-TA
TA,APPTA
W-141
Min. 15/32-
(Optional) PG100
None
PoWex SA Base
(Optional) APP-TA
APP TA
-90.0
Inch plywood
Min. 35/32-
None
SBS-SA
(OP tlonal)SBS-SA, SBS-
SBS-SA, APP-SA, SBS-
_97.5
W-142I
Inch plywood
PG100
TA, APP-TA
TA, APP TA
MIn. 15/32-
Plywood joints are covered with 4-Inch wide strips of Elastoflex SA V Plus, rolled Into
Elastofiex SA V Base or
(Optional) SBS-SA, SBS-
SBS-SA, APP-SA, SBS.
-97.5
W-143
inch plywood
(Optional) PG100
place to create continuous bond.
Elastollex SA V FR Base
TA, APP-TA
TA, APP-TA
W 144 I
Min. 25/32-
yyB-3000
None
SBS-SA
(Optional)
SBS-SA, APP-SA, SBS-
_105.0
Inch plywood
TA, APP-TA
Min. 15/32-
Plywood Joints are covered with 4-Inch wide strips ofElastoflex SA V Plus, rolled into
Elastofiex SA V Plus or
(Optlanel) SBS-SA, SBS-
SBS-SA, APP-SA, SBS-
-235.0
W 145
Inch plywood
(optional) PG100
place to create continuous bond.
Elastafiex SA V us Fit
TA, APP TA
TA, APP TA
Min. 15/32-
(Optional) PG100
Plywood Joints are covered with 4-Inch wile strips of Elastofiex SA V Plus, rolled into
palyllex SA Base
(Optional) APP-TA
APPTA
-135.0
Inch plywood
place to create continuous bond.
Exterlor 1"T.
se...h endDesign, LLC. d/b/aTrmhy(Ego Evaluation Report P9290.02.00-R20 for FL1654-R22
ofAuthorization t19SD3 6EDITION (2017) FBC NON-HVN2 EVALUATION Revision 20:09/12/2017
Robert Nleminen, PE-59155 Polyglass Modified Bitumen Roof Systems; (570) 334-2230 Appendix 1, Page 21 of 58