HomeMy WebLinkAboutPRODUCT APPROVALC AMYRD
YNT ®ID1UCTg®101'.IN�.L�BY
bC8'Y{YT -50 0 St LC1Ci,9 (;
This manual provides instructions for safe installation of •�
Square-D panel. The back plate sits securely on the face of t
allowing the front plate to slide be �e Interlock Kit onto a
between the main and generator breaker positions, he panel
IrtterLock Kit will only allow one of these breakers to be in the °° �� • •
the requirements of Article 702 of the National Electric Code The
installation of the breaker retaining strapmeets CN Position meeting
is Article 408.36 rsC 2008) 70' The
SArI ZTY z-1 , (riEc 2oos).
� �7^e�P ar'rAFO T A-UN7 T 6 AF' a jf 11tTSTRUcTy,DrT0Q
�' jAi'F.I\`T1i TG; ' Or' IM-V C"jr UC �i R 6Tf`-!I n-
�X--E 'T 0C1q
This kit must be installed and serviced only by qualified electrical Turn off all power supplying the equipment where this kit will be personnel
working on or inside the equipment installed before
Always use a properly rated voltage sensing device to corm that all
Off
Replace all devices, doors, and covers after installing this kit b power is
Power to the equipment before turning on
Always
equipment
wear safety eyewear while drilling or working around electric
al
To
., - -r
�.., FOLLOW T—j1,,�'ti
T.,U(C rC;Td ?XI aULT r ,.
Sr ~ TaES.'' 1BTS1TRVJC TxC' tTS
INST'ALI, TI®Id' INST�tiTCTY®
1) Disconnect power to the panel
2) separate plates. Remove backing from double stick tape. Align
So11) with the top of the first and second breaker slot (1,2 slot) back plate (P_ cover and under opening for main breaker. See FiOn front ofp I
time) gore (Do not drill holes at t
3) Remove panel cover his
4) Relocate breakers from slots 2 and 4 (top 2
utilizing Piggyback breakers as necessa spaces of the right breaker
5) Install generator breaker in the 2,4 slot. iy to create the needed spaces column)
6) Temporarily remove breakers from the 5,6 slots, Loop th
(S_1004) around breakers 1,2,3,4 _ , » P e breaker retaining strap
the head of the retaining strap at the top fight of the numb om the, front a of the breakers'tighten
Ali
the strap, See Figure JB Cut the tail of the retaining strap number 2 breaker and g
inches long and install Notice Label (5of the around
in the 1,6 slots. Veri ap approximate 2
fY that the retaining strap keeps the he 2,4 stall the breakers
attempting to remove the breaker. breaker in place by
7) On suitable surface use included 11164 drill bit
panel cover through the predrilled holes in the back plate �p drill01� t holes in the
8) Use file to smooth surface around holes and remove the burrs on back of
cover. On the back of the panel cover file awaypanel
head to sit with metal to metal contact. The binderi crews (H.5014)ow rmu re t
flush with the back °fthe panel cover must
sit
9) Insert binder screws (H.5014) through the back of the panel cover, back
5011), and front plate (P-5012). Use the binder post plate (P-
binder screws (H 5014). Handhold binder post (H-5013) while p �-$013) t° attach to front of
to tighten the binder screws (H-5014). The front plate should sIi'de agr�reand ever
back plate should sit firmly, Be careful not to over -tighten, y the
10}Set generator and inain breakers in the "OFF" position and reattach panel cover
Figure I
Figure IB
---- — ra11G1 cover t7rmly in place test the transfers easily between positions. Interlock to make sure that it
BOTH BREAKERS ABLE TO BE IN THE «ON�� POSITION AT THE SAME S SHOULD NOT BE
moderate pressure you should not be able to engage both breakers at once
TIME, Even with
12) Apply thread lock (H-so16) all four binder oat
p (H-5013) as per instructions
included with the thread Iock
13) Attach labels as shown in Figure II
14) Reconnect power to the panel :
Figure 11
Description Quantity
Back plate I
Front plate I
Binder post 4
Binder screw 4
Drill bit 11164 1
Thread lock pipette 1
Instruction booklet 1
Main label . 1
Da-4JVGER label 1
Generator label 1
-ns"'uations label . 1
Retaining Strap I
Retainin Stra Label I
Part #
P 5011
P-5012
H 5013
H 5014
H 5015
H-5016
W-5017
W-5018
W 5019
W 5020
W-5021
S-1004
S_1005
QLWSDEID T® INSTA L
Drill or cordless drill
- Flathead screwdriver
Metal file
Accurate voltage sensor
You can contact us b
2448 or by fax at (804) 31 1984hone at 804) 726-
Questions or comments:
uest'or�s i to locickit.com
/ � 1
TO SWITCH OPERATION FROM MAIN
TO GENERATOR
1) Turn main breaker to the "OFF"
Position
2) Turn all branch circuits to the
"OFF" position
3) Slide lnte:Lock plate up
4) Connect and start generator
5) Turn generator breaker to the
"ON" position
6) Turn on essential circuits one at
a time WA IMG: Allow
appliances to start before
engaging next circuit
TO RETURN TO MAIN POWER
REVERSE PROCEDURE
STAT`EMJEp�T fig+` It�4B.� ■ ..T�'
Electrical equipment should be installed,
Operated, serviced, and maintained b
qualified y
personnel. No responsibility is
assumed by Generator InterLock
Technologies, LLC for any consequences
arising out of the misuse of this material
Tested for use with
UL 67 Listed .Panelboards
Ref. Wyle Laboratories
Test .Report T52431.01