HomeMy WebLinkAboutPRODUCT REPORT - METAL ROOFINGFBC
TEST
PRI C
1. UL
2. UL
BY
with Florida Building Code 2017 (61 ed.)
with Florida Product Approval Rule # 61620.3
Quality Assurance Program: PRi CONSTRUCTION MATERIALS TECHNOLOGY
is: 1504.3.2. 1507
302 Milton Drive
Fort Pierce, FL 34962
(772) 466-4040
lrimp thru fastened W rib at each panel edge and 1 fastener in the center of the panel, 24" net coverage, 26GA ASTM
2, 6-50, AZ5S, .018, SOksi min. over min.15/32" thick CDX plywood deck. Corrosion Resistant fastener #9-15 HWH.with
ing washers, metal to wood connections with fastener length to penetrate 5/16" thru substrate. Fasten along the crown
ie rite in the center.of panel and along the lap. First fastener to be within 3" of panel edges. Min.. 8Dx2" annular ring shank
spaced 6" O.C: reroofing, with less than 19/32" plywood (min.1S/32"), this attachment is to be used in addition to
ling attachment. Deck slope 2:12 or greater and shall be compliant with FBC 2017 61"` ed'. Underlayment: See FBC 2017 6TM
Sec. 1507 Table 1507.1.1
"
Design Pressure:
r
Spacing:
-69.25 PSF
16" O.C.
-129.25 PSF
6" O.C.
ASTM A792, G-SO, AZ55, .018, SOksi Victorian Crimp Shingle over 15/32" CDX/APA Plywood attached to roof trusses.
xsion Resistant Fastener #10 x 1" Zinc plated, MTW Pancake Head, installed at 2 per panel into lock seam. Panels applied
12" exposure, adjacent shingles inserted Into lock seam of previous shingle. Deck slope 2:12 or greater and shall be
pliant with FBC 2017 6" ed. Underlayment: See FBC 2017 6T" ed., Sec.1507 Table 1507.1.1
**Design Pressure.
-_ -105 PSF
'LUDES A SAFETY
Reference Data:
Test Laboratory (TST 1527) #0224-0501-06
uction Materials Technologies (TST 5878) #FAE-023-02-01
M test standards are equivalent to UL 580-06 test standards.
test standards are equivalent to UL 1897--12
2:1
TAS 12S (UL 58G-941)
UL 580-06/1.11. 1897-W
Underlayment to be compliance with current Florida Building Code (FBC)2017 61" ed—see Chart 1507.1.1 -
Minimum slope to be compliant with Florida Building Code 2017 61' ed., and per with Manufacturer's installation reference.
Products are compliant with State of Florida product approval per Rule 61G20-3. Compliance Method: 1-D
Engineering analysis for "project specific approval by local authorities w/jurisdiction is allowed by other registered
engineers.
Fire classification is not part of this acceptance. Shear diaphragm values are. outside this report.
Support framing in compliance w/FBC 2017 6t' ed., Chapter 22 Steel, Chapter 23 Wood and Chapter 16 Structural Loading.
This report does not imply warranty, installation, recommended product use outside of this report.
of Independence:
Bowden, P.E. does not have' not will acquire a financial interest in any company manufacturi%?flJJjJ$iputing products
this evaluation.
Bowden, P.E. is not owned, operated, or controlled by any company, manufacturer, or I gr this
oQ G f
- seal No.
2
FL�. ��• '�,. O , ORA �
SSIQNPti�:►'`�.
''04+, i u►+++► 11%
5 V Crimp
Fastener- #9-15 corrosion resistant w/sealing washers
24"coverage
Fastener: #9 x 15 corrosion resistant with sealing washers
in Compliance with 2017 Florida Building Code, Section 1507
Perimeter fastening: 61'o.c.
Main Field fastening 12"o.c.
Panel Width: 26"
Panel Coverage: 24"maximum
26 GA Architectural Metal Roof panel
VICTORIAN CRIMP SH
IR
MINIMUM 2 FASTENERS
AT LOCK SEAM
) CUT 1/2 SHINGLE
REATE STAGGERED
'ERN
ORIAN CRIMP
GLES
9"EXPOSURE
N
Fastener.#10 x 1 "
Zinc Plated MTW
Pancake Head