HomeMy WebLinkAboutCYLINDER INFORMATION4
@CANNED
BY
n ucle County
71
50
35
40
52
HEIG
' T (IN)
LPG CAPACITY (GAL]
23.6
23.6
47.2
99.1
WA R CAPACITY (LBS)
239
239
474
1,000
MWA (PSIG]
250
250
250
250
CYLINDER DIAMETER (IN)
14.5
18
24
30
CYLI E,DER VOLUME (CU. IN)
COL R DIAMETER (IN)
6,629
11.4
6,629
16
13,120
16
27,680
16
COLLAR HEIGHT (IN)
6.4
6.9
6.9
6.9
FOOT ING DIAMETER (IN)
14.5
16.6
19
22
VALV
CGA-510 NO OPD
CGA-510 NO OPD
CGA-510 NO OPD
CGA-510 NO OPD
STAN
_
ARD SPECIFICATION
ASME
ASME
ASME
ASME
METRL
1,321
1,270
889
1,016
HEIGHT
(MM1
LI
PACITY (L)
86.7
86.7
172
360
WATE
, CAPACITY (KG).
108.4
108.4
215
450
MWAP*
(BAR)
17
17
17
17
CYLINIDER
DIAMETER (MM)
369
108.7
290
457
108.7
406
610
215
406
762
450
406
CYLItV�DER
COLLR
VOLUME (L)
DIAMETER (MM)
COLLAR
FOOTRING
HEIGHT (MM) 163
DIAMETER (MM) 368
^w CGA-510 NO OPO
175
422
CGA-510 NO OPD
175
483
CGA-510 NO OPD
175
559
CGA-510 NO OPD
VALV
STAN'
ARD SPECIFICATION ASME
ASME
ASME
ASME
*MWAP = Maximun\allowable working
ANNEX
(5) IA torch fire test shall be run for a minimum of 50 minutes.
The thermal insulation system shall retard the heat flow
to the steel plates so that none of the thermocouples on
the uninsulated side of the steel plate indicate a plate tem-
perature in excess of 800°F (427°G).
H.Jil Hose Stream Resistance Test. After 20 minutes' exposure
to the torch test, the test sample shall be hit with a hose stream
corii urrently with the torch for a period of 10 minutes.
Thel hose stream test shall be conducted in the following
(1) ifhe stream shall be directed first at the middle and then
fat all parts of the exposed surface, malting changes in
direction slowly.
(2) '�rlhe hose stream shall be delivered through a M in.
(64 min) hose discharging through a National Standard
playpipe of corresponding size equipped with a 1 r/a in.
i1(29 mm) discharge tip of the standard -taper smooth -bore
pattern without shoulder at the orifice. The water pres-
!isure at the base of the nozzle and for the duration of the
test shall be 30 psig (207 kPag). [Estimated delivery rate is
205 gpm (776 L/min).]
(3) ITIhe tip of the nozzle shall be located 20 ft (6 m) from, and
bn a line normal to, the center of the test specimen. if impos-
Q
o direct
intake t
vent appliance
aft
5 ft (m( in) (min)
Central AC (Note 1) (Note 3)
compressor Cylinders not filled on site
(source of Ignition)
at the point of use
For SI, units, i ft = 0,3048 m.
58-119
sible to be so located, die nozzle can be on a line with a
deviation not to exceed 30 degrees from the line normal to
the center of the test specimen. When so located, the dis-
tance from the center shall be less than 20 ft (6 m) by an
amount equal to 1 ft (0.3 m) for each 10 degrees of deviation
from the normal.
(4) Subsequent to the application of the hose stream, the
torching shall continue vi itil any thermocouple on the
uninsulated side of the steel plate indicates a plate tem-
perature in excess of 800°F (427°C).
(5) The thermal insulation system shall be judged to be resis-
tant to the action of the hose stream if the time from
initiation of torching for any thermocouple on the unin-
sulated side of the steel plate to reach in excess of 800°F
(427°C) is 50 minutes or greater.
(6) One successful combination torch rile and hose stream
test shall be required for certification.
Annex I Container Spacing
This annex is not a part of the requirements of this .NFPAdocument
but is included for informational purposes only.
I.1 Spacing of Containers. Figure I.I (a), Figure I.1(b), and
Figure 1.1(c) illustrate container spacing required in 6.31.
Window air
conditioner
(source of
;� ignition)
10 ft (min)
(Note 2)
Crawl space opening,
windows, or exhaust fan
3 ft Cylinder filled on
(min) site at the point
(Note 3) of use from
bulk truck
ivocas
(1) 5 minimum from relief valve In any direction away from any exterior source of Ignition, openings into direct -vent appliances,
or mechanical ventilation air Intakes. Refer to Table 6.3.4.3.
(2) if a cylinder is filled on site at the point of use from a bulk truck, the filling connection and vent valve must beat least
10 ft f'pm any exterior source of ignition,. openings Into direct -vent appliances, or mechanical ventilation air Intakes.
Refer �o 6.3.4.4.
(3) Rc (erto 6.3.4.3.
I.1(a) Cylinders. (Figure for illustrative purposes only; code compliance required )
2014 Edition