HomeMy WebLinkAboutNOA - GAF LEAK BARRIERS - ROOF DECK PROTECTIONMIAMN®ADE�
DEPARTMENT OF REGULATORY AND ECONOMIC RESOURCES (RER)
BOARD AND CODE ADMINISTRATION DIVISION
NOTICE OF ACCEPTANCE i
GAF
1 Campus Drive
Parsipanny, NJ 07054
MIAMI-DADE COUNTY
PRODUCT CONTROL SECTION
11805 SW 26 Street, Room 208
Miami, Florida 33175-2474
T (786) 315-2590 F (786) 315-2599
www.miatnidade.gov/cconomy
SCANNED
BY 8�31' l8
SCOPE:
01 LI Gle UOUMY
This NOA is being issued under the applicable rules and regulations governing the use of construction materials. The
documentation submitted has been reviewed and accepted by Miami -Dade County RER - Product Control Section to be
used in Miami Dade County and other areas where allowed by the Authority Having Jurisdiction (AHJ).
This I iOA shall not be valid after the expiration date stated below. The Miami -Dade County Product Control Section
(In Miami Dade County) and/or the AHJ (in areas other than Miami Dade County) reserve the right to have this
product or material tested for quality assurance purposes. If this product or material fails to perform in the accepted
manner, the manufacturer will incur the expense of such testing and the AHJ may immediately revoke, modify, or
suspend the use of such product or material within their jurisdiction. RER reserves the right to revoke this acceptance,
if it is determined by Miami -Dade County Product Control Section that this product or material fails to meet the
requirements of the applicable building code.
This product is approved as described herein, and has been designed to comply with the Florida Building Code
including the High Velocity Hurricane Zone of the Florida Building Code.
i
DESCRIPTION: GAF Leak Barriers and Roof Deck Protection
LABELING: Each unit shall bear a permanent label with the manufacturer's name or logo, city, state and following
statement: "Miami -Dade County Product Control Approved", unless otherwise noted herein.
RENEiWAL of this NOA shall be considered after a renewal application has been filed and there has been no change
in the applicable building code negatively affecting the performance of this product.
I
TERMINATION of this NOA will occur after the expiration date or if there has been a revision or change in the
materials, use, and/or manufacture of the product or process. Misuse of this NOA as an endorsement of any product,
for sales, advertising or any other purposes shall automatically terminate this NOA. Failure to comply with any section
of this NOA shall be cause for termination and removal of NOA.
ADVERTISEMENT: The NOA number preceded by the words Miami -Dade County, Florida, and followed by the
expiration date may be displayed in advertising literature. If any portion of the NOA is displayed, then it shall be done
in its entirety.
INSPECTION: A copy of this entire NOA shall be provided to the user by the manufacturer or its distributors and
shall be available for inspection at the job site at the request of the Building Official.
This TA renews and revises NOA 16-1213.04 and consists of pages 1 through 1
The submitted documentation was reviewed by Hamley Pacheco, P.E.
MU4MFOAD
"FILE COPY
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Pagel of 10
ROOFING COMPONENT APPROVAL
I
Category: Roofing
Sub-dategory: Underlayment
Material: SBS/Polypropylene/Asphalt
1 -
PRODUCTS DESCRIPTION:
Product
WeatlierWatch® Mineral
Surfaced Leak Barrier
Manufacturing
Location #1, 9
StormGuarda Film
Surfaced Leak Barrier
Manufacturing
Location #1, 9
LiberWm SBS Self-
Adher�ng Base/Ply Sheet
Manufacturing
Location #1, 9
I
Deck-ArmorTM Premium
Breathable Roof Deck
Protection
Manufacturing
Location #2
1
Tiger PaWTM Roof Deck
Protection
Manufacturing
Location #3, 5, 6
FeltBusiter® High -Traction
Synthetic Roofing Felt
Manufacturing
Location #7, 8
ShingleiMate® Roof Deck
Protection
Manufacturing
Location #4
MIAMMADECOUNTY
Test
Dimensions Specification
Product
Description
36" x 50' rolls ASTM D 1970 Granular surfaced modified, fiberglass reinforced,
36" x 66.7' rolls bituminous sheet material for use as a leak `barrier
underlayment in sloped roof assemblies.
Designed as an ice & rain shield.
36" x 66.7' rolls ASTM D 1970 Modified, fiberglass reinforced, bituminous sheet
material for use as a high temperature leak barrier
underlayment in sloped roof assemblies.
Designed as an ice & rain shield.
39 3/s" x 66' rolls ASTM D 1970
ASTM D4601
Type 11
Self -adhering SBS roof membrane.
54" x 222' rolls ASTM D 226 A UV -stabilized polypropylene breathable
48" x 100' rolls Type H underlayment. To be used for roof deck
protection as an underlayment in sloped roof
assemblies.
48" x 250' rolls ASTM D 226 A UV -stabilized polypropylene non -breathable
48" x 100' rolls Type 11 underlayment. To be used for roof deck protection
as an underlayment in sloped roof assemblies.
48" x 250' rolls ASTM D 226 A UV -stabilized polypropylene non -breathable
Type I underlayment. To be used for roof deck protection
as an underlayment in sloped roof assemblies.
36" x 144' rolls ASTM D 226 Fibergass-reinforced asphalt felt underlayment. To
Type I be used for roof deck protection as an
underlayment in sloped roof assemblies.
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 2 of 10
I
PRODUCTS DESCRIPTION:
i
Test
Product Dimensions Specification
LibertIyTM SA Glass Cap 393/8" x 34' rolls ASTM D 1970
Sheet I ASTM D 6163
Manufacturing ASTM D 7530
Location # 9
Product
Description
Granular surfaced modified, fiberglass reinforced,
self -adhering SBS roof membrane.
GAFGLAS@ Ply 4 39.37" ASTM D2178 Aspahalt impregnated glass felt with aspahlt
Manufacturing (1 meter) Wide Type IV coating.
Location # 9,10
GAFGLAS® F1exP1yTM 6 39.37" ASTM D2178 Aspahalt impregnated glass felt with aspahlt
Manufacturing (1 meter) Wide Type VI coating.
Location # 9,10
I
MANUFACTURING LOCATION:
1.Mt. Vernon, IN
2.North Bay, Ontario
3.1 lission, British Columbia
4.Pryor, OK
5.Qingdao, China
6.Charleston, SC
7.Spartanburg, SC
8.Dadra, India
9.Savannah, GA
10 jMobile, AL
I
I
MIAMMADE COUNTY
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 3 of 10
,I
EVIDENCE SUBMITTED:
i Test Agency
Test Identifier
Test Name/Report
Date
Interte'k Testing Services NA Ltd.
3077464-01
ASTM D 1970
08/23/06
3090131
Wind Uplift and Self Sealability
08/23/06
100258583COQ-OIOA
ASTM D 226 Type H
01/08/11
100673818COQ-003
ASTM D 226 Type H
06/13/13
10157289000Q-005
ASTM D 226 Type 11
04/17/14
F8549.02-106-18
ASTM D 226 Type I
11/08/16
PRI Construction Materials
RGM-023-02-01
ASTM D 4798
05/16/07
Techn I logies, LLC.
GAF-112-02-01
ASTM D 226 Type 11
03/15/06
GAF-238-02-01
ASTM D 1970
03/03/10
GAF-323-02-01
ASTM D 1970
11/30/11
GAF-324-02-01
ASTM D 1970
12/01/11
GAF-325-02-01
ASTM D 1970
12/01/11
GAF-326-02-01
ASTM D 1970
11/30/11
GAF-275-02-01
ASTM D 1970
11/11/10
GAF-344-02-01
ASTM D 1970
04/23/12
GAF-339-02-01
ASTM D 226 Type I
03/14/12
ELK-311-02-01
ASTM D 1970
09/11/07
GAF-518-02-01
ASTM D 226 Type 1
06/04/14
GAF-818-02-01
ASTM D 4533
12/06/17
GAF-829-02-01
ASTM D 226 Type H
01/15/18
GAF-314-02-01
ASTM D 2178
07/21/11,
GAF-315-02-01
ASTM D 2178
07/21/11
Trinity!ERD
GAF-SC13285.03.17-1
ASTM D 1970
03/08/17
GAF-SC13285.03.17-3
ASTM D 1970
03/01/17
GAF-SC13285.03.17-4
ASTM D 1970
03/01/17
GAF-SC13285.02.17-2
ASTM D 4601 Type 11
02/08/17
GAF-SC9700.08-15-R1
ASTM D 2178
09/09/15
GAF-SC12915.12.17-RI
ASTM D 1970
12/11/17
GAF-SC12915.12.17-RI
ASTM D 6163
12/11/17
GAF -SC 12915.12.1'1-Rl
ASTM D 7530
12/11/17
i
NOA No.: 18-0119.15
MIAMMADECOUNTY Expiration Date: 02/22/23
i Approval Date: 02/22/18
Page 4 of 10
APPROVED ASSEMBLIES:
Deck Type 1: Wood, non -insulated
DeckDescription: 19/32" or greater plywood or wood plank
System E (1): Anchor sheet mechanically fastened to deck, membrane adhered.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle -Mate® Roof Deck Protection OR one or more plies
of ASTM D 226 Type II, Deck -Armor Premium Breathable Roof Deck Protection, FeltBuster®
High -Traction Synthetic Roofing Felt, or Tiger Paw' Roof Deck Protection with a minimum 4"
side lap and a 6" end lap mechanically fastened to the deck with approved nails and tin caps 6"
o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape (follow the tape's manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
I
Membrane: One or more plies of WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film
Surfaced Leak Barrier, LibertyTM SA Glass Cap Sheet, or LibertyTM SBS Self -Adhering
Base/Ply Sheet membrane with a minimum 3" side lap and 6" end lap. Place the first course of
membrane parallel to the eave, rolling the membrane to obtain maximum contact. Remove the
release membrane as the membrane is applied. Vertical strapping of the roof with
WeatherWatch® Mineral Surfaced Leak Barrier, or StormGuard® Film Surfaced Leak Barrier is
acceptable.
Surfacing: Approved Roofing Assembly.
NOA No.: 18-0119.15
Mta MaDaDe couNrY Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 5 of 10
I
I
DeckllType 1: Wood, non -insulated
DeckiDescription: 19/32" or greater plywood or wood plank
System E(2): Membrane mechanically fastened to deck.
Separ, ator Sheet: One or more plies of GAFGLAS® Ply 4, GAFGLAS® FlexPlyTM 6, Shingle -Mate® Roof Deck
Protection, Deck-Armoi' Premium Breathable Roof Deck Protection, FeltBuster® High -
Traction Synthetic Roofing Felt, or Tiger Pawl Roof Deck Protection loose laid.
Membrane: One or more plies of WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film
Surfaced Leak Barrier, LibertyTM SA Glass Cap Sheet, or Libert3 T SBS Self -Adhering
Base/Ply Sheet membrane mechanically fastened with a minimum 3" side lap and a 6" end lap to
deck through the separator sheet with approved nails and tin caps 6" o.c. at the laps and two
staggered rows 12" o.c. in the field of the roll.
Surfacing: Approved Roofing Assembly.
i
i
I
i
MIAMI-DARE COUNTY
I
I
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 6 of 10
DecklType 1:
Wood, non -insulated
Deck Description:
"/32" or greater plywood or wood plank
System E (3):
Anchor sheet mechanically fastened to deck, membrane adhered.
Secondary Water
Install a minimum 4" wide WeatherWatch® Mineral Surfaced Leak Barrier,, LibertyTM SBS
Barrier:
Self -Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, or StormGuard® Film Surfaced
(Optional)
Leak Barrier membrane over the joints of the plywood roof deck prior to installation of the base
sheet. Do not overlap end or side joints. All side and end laps should be butted firmly side by
side, flush with each other but not overlapped. Do not leave the WeatherWatch® Mineral
Surfaced Leak Barrier, or StormGuard® Film Surfaced Leak Barrier membrane exposed for more
than 30 days without a roof deck protection underlayment protecting the secondary water barrier.
Base Sheet:
Two plies of ASTM D 226 Type I or Shingle -Mate® Roof Deck Protection OR one or more plies
i
of ASTM D 226 Type II, Deck -Armor" Premium Breathable Roof Deck Protection,
FeltBuster® High -Traction Synthetic Roofing Felt, or Tiger Paw' Roof Deck Protection with a
minimum 4" side lap and a 6" end lap mechanically fastened to the deck with approved nails and
tin caps 6" o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape (follow the tape manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fasteners.
Surfacing:
I
Approved Roofing Assembly.
NOA No.: 18-0119.15
MIAMI>DAOE COMM Expiration Date: 02/22/23
j Approval Date: 02/22/18
Page 7 of 10
y
Deck Type 1: Wood, non -insulated
Deck1 Description: 19/32" or greater plywood or wood plank
SystelI E (4): Anchor sheet mechanically fastened to deck, membrane adhered.
Base Sheet: Two plies of ASTM D 226 Type I or Shingle -Mate® Roof Deck Protection OR one or more plies
of ASTM D 226 Type II, Deck-Armoi' Premium Breathable Roof Deck Protection,
FeltBuster® High -Traction Synthetic Roofing Felt, or Tiger Paw' Roof Deck Protection with a
minimum 4" side lap and a 6" end lap mechanically fastened to the deck with approved nails and
tin caps 6" o.c. at the laps and four staggered rows 12" o.c. in the field of the roll.
If roof is exposed to rain/snow, tape all end and side laps with approved butyl adhesive based
seam/cover tape or an approved waterproof cloth duct tape (follow the tape's manufacturer's
installation instructions). Always apply tape over all fasteners at the center of the roll or the end
laps to help prevent rain or snow from entering at the fastneners.
Membrane: One or more plies of StormGuard® Film Surfaced Leak Barrier membrane with a minimum 4"
side lap and 6" end lap. Place the first course of membrane parallel to the eave,, rolling the
membrane to obtain maximum contact. Remove the release membrane as the membrane is
applied.
Surfacing: Approved for Metal roofing, Slate, and Asphalt Shingle assemblies.
I
I
MIAMLDADE COUNTY
I
I
i
NOA No.: 18-0119.15
Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 8 of 10
i
LIMITATIONS:
1. Fire classification is not part of this acceptance.
2. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-Armoi'
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection shall not be used as roof tile underlayment.
3. This acceptance is for prepared roofing applications. Minimum deck requirements shall be in compliance with
applicable building code. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak
Barrier, LibertyTM SBS Self -Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate° Roof Deck
Protection, Deck-ArmorTM Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic
Roofing Felt, and Tiger PawTM Roof Deck Protection shall be installed in strict compliance with applicable
Building Code.
4. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mateo Roof Deck Protection, Deck-Armoi'
Premium Breathable Roof Deck Protection, FeltBusterg High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection membranes shall be applied to a smooth, clean and dry surface with deck free of
irregularities.
5. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyT SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate' Roof Deck Protection, Deck-ArmorTM
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection membranes shall not be applied over an existing roof membrane.
1
6. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-Armoil
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection shall not be left exposed as a temporary roof for longer than 30 days of application.
7. WeatherWatch® Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -
Adhering Base/Ply Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mateo Roof Deck Protection, Deck -Armor m
Premium Breathable Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM
Roof Deck Protection may be used with any approved roof covering Notice of Acceptance listing WeatherWatch®
Mineral Surfaced Leak Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -Adhering Base/Ply
Sheet, LibertyTM SA Glass Cap Sheet, Shingle -Mate' Roof Deck Protection, Deck-Armoi' Premium Breathable
Roof Deck Protection, FeltBuster® High -Traction Synthetic Roofing Felt, and Tiger PawTM Roof Deck Protection
as is component part of an assembly in the Notice of Acceptance. If WeatherWatch® Mineral Surfaced Leak
Barrier, StormGuard® Film Surfaced Leak Barrier, LibertyTM SBS Self -Adhering Base/Ply Sheet, LibertyTM SA
Glass Cap Sheet, Shingle -Mate® Roof Deck Protection, Deck-Armof' Premium Breathable Roof Deck Protection,
FeltBuster® High -Traction Synthetic Roofing Felt and Tiger PawTM Roof Deck Protection are not listed; a request
may be made to the Authority Having Jurisdiction (AHJ) or the Miami -Dade County Product Control Department
fort approval provided that appropriate documentation is provided to detail compatibility of the products, wind
uplift resistance, and fire testing results.
8. All, nails in the deck shall be carefully checked for protruding heads. Re -fasten any loose decking panels. Sweep
thei deck thoroughly to remove any dust and debris prior to application. Install when temperatures are 451 F and
rising.
9. When applying the membrane in the valley, start at the low point and work to the high point, rolling the membrane
from the center outward in both directions.
i
NOA No.: 18-0119.15
MIAMI.DADS COUNTY Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 9 of 10
LIMITATIONS:
I
10. Roll or broom the entire membrane surface so as to have 100% contact with the surface, giving special attention to
7erlap areas.
11. Flash vent pipes, stacks, chimneys and penetrations in compliance with Roof Assembly current Product Control
Notice of Acceptance and applicable Building Code.
12. All products listed herein shall have a quality assurance audit in accordance with the Florida Building Code and
Rule 61 G20-3 of the Florida Administrative Code.
13. All membranes or packaging shall bear the imprint or identifiable marking of the manufacturer's name or logo,
6ity and state of manufacturing facility, and the following statement: "Miami -Dade County Product Control
Approved" or the Miami -Dade County Product Control Seal as shown below.
MlAM1 DADS COUNTY
,,..O
END OF THIS ACCEPTANCE
NOA No.: 18-0119.15
MIAMbDADB COUNTY Expiration Date: 02/22/23
Approval Date: 02/22/18
Page 10 of 10